Skip to Content
You are currently on the new version of our website. Access the old version .

1,992 Results Found

  • Article
  • Open Access
2,063 Views
32 Pages

Improvement of the Analytical Model of an Energy Dissipator and Validation with Experimental Tests of a Prototype

  • Esteban Balboa-Constanzo,
  • Nelson Maureira-Carsalade,
  • Frank Sanhueza-Espinoza,
  • Ángel Roco-Videla and ,
  • Marcelo Sanhueza-Cartes,
  • Patricio Arias-Guzmán and
  • Cristian Canales
  • + 2 authors+ 0 author

9 September 2023

An improved numerical formulation for a self-centering frictional damper is presented. This was experimentally validated through quasi-static tests carried out on a steel-made prototype of the damper. Its design is ad hoc for implementation in the se...

  • Feature Paper
  • Article
  • Open Access
7 Citations
3,446 Views
16 Pages

Conceptualization and Prototype of an Anti-Erosion Sensing Revetment for Levee Monitoring: Experimental Tests and Numerical Modeling

  • Manuel Bertulessi,
  • Daniele F. Bignami,
  • Ilaria Boschini,
  • Andrea Chiarini and ,
  • Maddalena Ferrario,
  • Nicola Mazzon,
  • Giovanni Menduni,
  • Jacopo Morosi and
  • Federica Zambrini
  • + 4 authors+ 0 author

28 October 2020

The problem of levee embankment control during high flows is crucial for flood risk management in floodplains. Levee defense lines are often hundreds of kilometers long and surveys during emergencies are not easy tasks. For these reasons, levees moni...

(This article belongs to the Section Hydrology)
  • Article
  • Open Access
7 Citations
6,004 Views
12 Pages

This paper presents an efficient method of estimation of rotor cage temperature for induction machine design, applied for electric and hybrid vehicles. This factor influences the torque produced by the induction machine with a field-oriented control...

(This article belongs to the Section Power Electronics)
  • Article
  • Open Access
5 Citations
4,401 Views
14 Pages

Experimental Determination of the Energetic Performance of a Racing Motorcycle Battery-Pack

  • Pablo Esparza,
  • Sandra Castano-Solis,
  • David Jiménez-Bermejo,
  • Jesús Fraile Ardanuy and
  • Manuel Merino

31 October 2020

This paper presents the evaluation of the energetic performance of the battery-pack from the motorcycle prototype EME 16E. This racing prototype was developed by a student team from the Universidad Politécnica de Madrid (UPM) to participate in...

(This article belongs to the Special Issue Power System Expansion Planning)
  • Technical Note
  • Open Access
1,811 Views
10 Pages

Novel Concept for the Expansion of the Fibula Bone as an Autologous Bone Graft: Experimental Tests on an Animal Implant Prototype—In Memoriam Volker Buehren

  • Matthias Militz,
  • Volker Buehren,
  • Christoph Miethke,
  • Carolin Gabler and ,
  • Josephine Mauck,
  • Wolfram Mittelmeier,
  • Robert Bialas and
  • Rainer Bader
  • + 3 authors+ 0 author

22 March 2024

The current reconstructive surgical procedures implemented after the resection of extended bone segments are associated with high complication rates and long-term treatments. By transplanting an autologous, vascularized and stabilized bone segment, t...

  • Article
  • Open Access
2 Citations
4,802 Views
21 Pages

Mechanical Design and Experimental Study of a Small-Scale Wind Turbine Model

  • Eduardo Muñoz-Palomeque,
  • Segundo Esteban and
  • Matilde Santos

8 October 2025

The advancement of onshore and offshore wind turbines depends on the experimental validation of new technologies, novel component designs, and innovative concepts. However, full-scale models are typically very expensive, have limited functionality, a...

(This article belongs to the Special Issue Recent Developments in Machine Design, Automation and Robotics, Second Edition)
  • Article
  • Open Access
5 Citations
3,742 Views
21 Pages

Test Stand for Microjet Engine Prototypes

  • Cornel Mihai Tărăbîc,
  • Grigore Cican,
  • Cristian Olariu,
  • Gabriel Dediu and
  • Răzvan Marius Catană

30 September 2024

To investigate the functionality and performance of a prototype microjet engine, we constructed a versatile test stand tailored to the specifications of a 400 N prototype. This test stand facilitated a comprehensive study by enabling real-time record...

(This article belongs to the Section Turbomachinery)
  • Article
  • Open Access
3,613 Views
20 Pages

Experimental Testbed for Nondestructive Analysis of Curtain Airbags in Child Safety Applications

  • Isaac Lopez-Alvarez,
  • Christopher René Torres-SanMiguel,
  • Ivan Lenin Cruz-Jaramillo,
  • Juan Alejandro Flores-Campos and
  • Ilse Cervantes

Side impacts tend to produce more severe injuries than frontal collisions, particularly for vulnerable occupants such as children. Despite this, there is a limited number of studies and developments focused on side impact protection systems, and exis...

  • Article
  • Open Access
4 Citations
1,442 Views
37 Pages

10 November 2025

The increasing demand for sustainable engineering solutions has driven extensive research into natural fibre-reinforced composites (NFCs), notably flax fibre-reinforced polymers (FFRPs), which offer promising eco-friendly alternatives to synthetic co...

(This article belongs to the Section Polymer Composites and Nanocomposites)
  • Article
  • Open Access
4 Citations
3,028 Views
14 Pages

Geothermal Pavements: Experimental Testing, Prototype Testing, and Numerical Analysis of Recycled Demolition Wastes

  • Behnam Ghorbani,
  • Arul Arulrajah,
  • Guillermo A. Narsilio,
  • Suksun Horpibulsuk and
  • Apinun Buritatum

2 February 2023

Geothermal pavements have the potential to reduce the pavement surface temperature by circulating fluid in pipes within the pavement structure. This research investigated an innovative geothermal pavement system with multiple benefits, such as reduci...

(This article belongs to the Special Issue Waste to Value – Use of Innovative Green Materials in the Construction of Transportation Infrastructure)
  • Article
  • Open Access
2 Citations
2,754 Views
23 Pages

Research and Experimental Testing of a Remotely Controlled Ankle Rehabilitation Exoskeleton Prototype

  • Assylbek Ozhiken,
  • Gani Sergazin,
  • Kassymbek Ozhikenov,
  • Haohan Wang and ,
  • Nursultan Zhetenbayev,
  • Gulzhamal Tursunbayeva,
  • Asset Nurmangaliyev and
  • Arman Uzbekbayev
  • + 3 authors+ 0 author

6 November 2025

Today, there is a high demand for remote rehabilitation using mobile robotic complexes all over the world. They offer a wide range of options for convenient and effective therapy at home to patients and the elderly, especially those bedridden after m...

(This article belongs to the Section Sensors and Robotics)
  • Article
  • Open Access
21 Citations
8,104 Views
16 Pages

11 January 2017

In this paper, we propose a reliability-oriented design of a linear generator-based prototype of a wave energy conversion (WEC), useful for the production of hydrogen in a sheltered water area like Mediterranean Sea. The hydrogen production has been...

(This article belongs to the Special Issue Wave Energy Converters)
  • Article
  • Open Access
3 Citations
10,009 Views
20 Pages

15 March 2019

In this study, the simulation parameters of the door hinge were investigated in the Z direction to have a correlation between the experimental test and simulation. Tests and simulations were conducted according to the United Nations Economic Commissi...

  • Article
  • Open Access
6 Citations
2,743 Views
12 Pages

Prototype Tests on Screwed Steel–Aluminium Foam–Steel Sandwich Panels

  • Elena Elettore,
  • Massimo Latour,
  • Mario D’Aniello,
  • Raffaele Landolfo and
  • Gianvittorio Rizzano

13 November 2023

Metal foams are newly developed engineered materials with attractive mechanical properties such as lightness, high resistance-to-weight ratio, and insulation capabilities. Lately, applications of these technologies have demonstrated the possibility o...

(This article belongs to the Special Issue Studies on Metal Materials and Their Applications in Building Structures)
  • Article
  • Open Access
861 Views
21 Pages

Experimental Validation of CFD Predictions for Internal Duct Airflow and Thermal Behaviour in a High-Speed Train Supply Duct Prototype: A Preliminary Stage Towards Carbody Integrated HVAC Testing

  • Fauzun Fauzun,
  • Muhammad Arkan Febian Hermada,
  • Fakhreza Areli,
  • Arsyadani Tsalisul Ilham and ,
  • Fariz Galang Nusantara Putra Setiawan,
  • Samsul Ma’arip and
  • Cahyo Wibi Yogiswara
  • + 2 authors+ 0 author

24 July 2026

Unlike many previous high-speed train Heating, Ventilation, and Air Conditioning (HVAC) studies that combined numerical and experimental analyses within the cabin, this study evaluates the supply duct independently, offering a more targeted assessmen...

(This article belongs to the Section Chemical, Civil and Environmental Engineering)
  • Article
  • Open Access
10 Citations
11,336 Views
26 Pages

21 February 2024

This study aims to develop and evaluate a vertically rotated fin shading system for an energy-efficient, user-friendly office space. The system was designed to protect a 4 × 8 m office room with a south-facing facade from excessive solar radiat...

(This article belongs to the Special Issue New European Bauhaus (NEB) in Architecture, Construction and Urbanism)
  • Article
  • Open Access
7 Citations
5,182 Views
25 Pages

Developing wind tunnel models is time consuming, labor intensive, and expensive. Rapid prototyping for wind tunnel tests is an effective, faster, and cheaper method to obtain aerodynamic performance results while considerably reducing acquisition tim...

(This article belongs to the Section Aeronautics)
  • Feature Paper
  • Article
  • Open Access
7 Citations
3,637 Views
14 Pages

15 October 2021

This work is part of the project called “Gölem project”, started in 2017, about special devices developed to enable the so-called Accessible Tourism. This project aims to design and develop a trekking wheelchair for people with impaired mobility. Aft...

(This article belongs to the Special Issue New Trends in Design Engineering)
  • Article
  • Open Access
4 Citations
3,064 Views
15 Pages

Experimental Characterization of Thermal Conductivity with a New Compact Hot-Box Prototype

  • Francisco A. Ramírez-Rivera,
  • Néstor Guerrero-Rodríguez,
  • Yokasta García-Frómeta,
  • Diógenes Vargas and
  • Mauricio Montanaro

9 April 2025

In this study, a new compact “hot-box” prototype with a volume of 0.602 m3 has been designed, instrumented, and implemented to experimentally characterize the thermal conductivity of specimens measuring 25 cm × 25 cm, with the thick...

(This article belongs to the Special Issue Novel Research on Heat Transfer and Thermodynamics)
  • Article
  • Open Access
6 Citations
3,433 Views
31 Pages

30 January 2023

New knowledge in multidisciplinary methodology is presented in this article for the design, aerodynamic optimization, and model validation of an adaptive wing prototype. The optimization framework integrates the design, the finite element analysis, a...

(This article belongs to the Section Aerospace Science and Engineering)
  • Feature Paper
  • Article
  • Open Access
3,415 Views
20 Pages

Quasi-Prototype Size Testing of Wedge-Shaped Block for Armoring Embankment Dams and Levees

  • Francisco Javier Caballero,
  • Miguel Ángel Toledo,
  • Rafael Moran and
  • Javier Peraita

8 February 2023

A series of tests of wedge-shaped blocks intended for armoring embankment dams and levees was carried out in a new experimental facility (‘Hydraulic Experimentation Facility—Luis Ruano’) under quasi-prototype conditions. This unique...

(This article belongs to the Special Issue Dam Safety. Protection against Overtopping and Prevention of Geo-Structural Failure)
  • Article
  • Open Access
12 Citations
10,031 Views
25 Pages

An Embedded System in Smart Inverters for Power Quality and Safety Functionality

  • Rafael Real-Calvo,
  • Antonio Moreno-Munoz,
  • Juan J. Gonzalez-De-La-Rosa,
  • Victor Pallares-Lopez and ,
  • Miguel J. Gonzalez-Redondo and
  • Isabel M. Moreno-Garcia
  • + 1 author+ 0 author

18 March 2016

The electricity sector is undergoing an evolution that demands the development of a network model with a high level of intelligence, known as a Smart Grid. One of the factors accelerating these changes is the development and implementation of renewab...

(This article belongs to the Special Issue Microgrids)
  • Article
  • Open Access
2 Citations
3,616 Views
25 Pages

Laboratory and Physical Prototype Tests for the Investigation of Hydraulic Hysteresis of Pyroclastic Soils

  • Marianna Pirone,
  • Alfredo Reder,
  • Guido Rianna,
  • Luca Pagano and ,
  • Marco Valerio Nicotera and
  • Gianfranco Urciuoli
  • + 1 author+ 0 author

Proper soil water retention curves (SWRCs) are necessary for a fair analysis of groundwater flow in unsaturated slopes. The question is whether hydraulic parameters operating in situ can be reliably determined from laboratory tests or physical protot...

(This article belongs to the Special Issue Innovative Strategies for Sustainable Mitigation of Landslide Risk)
  • Article
  • Open Access
7 Citations
3,018 Views
22 Pages

Design Parameters Affecting the Performance of Vortex-Induced Vibration Harvesters

  • Alberto Pasetto,
  • Michele Tonan,
  • Federico Moro and
  • Alberto Doria

22 January 2025

Vortex-induced vibration harvesters are usually equipped with small piezoelectric patches mounted near the cantilever clamp, where the largest longitudinal stress occurs. This paper, aiming to improve energy harvesting performance, investigates the p...

(This article belongs to the Special Issue Piezoelectric MEMS/NEMS—Materials, Devices, and Applications, Third Edition)
  • Article
  • Open Access
8 Citations
3,683 Views
10 Pages

A Design of a 2 DoF Planar Parallel Manipulator with an Electro-Pneumatic Servo-Drive—Part 2

  • Jakub Takosoglu,
  • Urszula Janus-Galkiewicz and
  • Jaroslaw Galkiewicz

24 March 2023

This paper is the second part of the study of a planar manipulator and this section presents the construction of a prototype manipulator. A fuzzy control system for the manipulator is described in detail. An experimental study was carried out on the...

(This article belongs to the Special Issue Advanced Fluid Power and Mechatronics)
  • Article
  • Open Access
602 Views
22 Pages

Multi-Physics Design, Manufacturing, and Experimental Validation of a High-Efficiency IPMSM for Compact Electric Vehicles

  • Hayatullah Nory,
  • Ahmet Yildiz,
  • Nesibe Sibel Akbulut,
  • Abdurrahman Atila and
  • Ahmet Orhan

17 July 2026

This study presents the design, manufacturing, and prototype-level evaluation of a high-efficiency interior permanent magnet synchronous motor (IPMSM) developed for compact electric vehicle traction applications. The proposed motor employs a 12-slot/...

(This article belongs to the Special Issue Design, Performance Optimization and Application of Permanent Magnet Motors)
  • Article
  • Open Access
1,236 Views
17 Pages

16 February 2026

This paper presents a new approach to the design of hydraulic pumps, exemplified by a prototype gerotor pump with an integrated direct drive, based on an original concept constituting the basis of the Polish patent PL 236677. One of the objectives of...

  • Article
  • Open Access
1 Citations
6,142 Views
18 Pages

Structural Design and Simulation of Multi-Detector Same-Platform Laser Gyro Reflector Substrate Defect Detection Prototype

  • Jun Wang,
  • Zhenyang Li,
  • Maoxin Song,
  • Zhilong Xu and ,
  • Huan Luo,
  • Mingchun Ling,
  • Hengwei Qin,
  • Wuhao Liu,
  • Zhenhai Liu and
  • Jin Hong
  • + 5 authors+ 0 author

15 December 2024

Defect detection and classification in super-high reflector mirrors and their substrates are crucial for manufacturing laser gyroscope systems. This paper presents a prototype designed to meet the requirements for the reflection and transmission of l...

(This article belongs to the Section B: Biology and Biomedicine)
  • Article
  • Open Access
4 Citations
3,275 Views
15 Pages

1 September 2019

In most scale model tests of steel frame structures, researchers have usually paid more attention to the outcome of one single experiment rather than to the similitude error between the scale model and the prototype. As a result, only the experimenta...

(This article belongs to the Section Civil Engineering)
  • Article
  • Open Access
10 Citations
4,009 Views
12 Pages

Design and Construction of a Prototype of an Assisting Device for Arm Exercise

  • Marco Ceccarelli,
  • Susana Sanz,
  • Vicente Díaz and
  • Matteo Russo

17 February 2024

A new portable arm exercise device is presented as a laboratory prototype to assist arm movements in rehabilitation therapies and movement exercises. Unlike the devices currently used, a portable design is proposed, with easy assembly and operational...

(This article belongs to the Section Automation and Control Systems)
  • Article
  • Open Access
857 Views
19 Pages

A 3D-Printed Nasopharyngeal Swab Prototype with a Helical Tip Design: A Feasibility Study with Numerical/Experimental Correlation

  • Francesco Nicassio,
  • Marta De Giorgi,
  • Francesca Lionetto,
  • Zahra Rajabimashhadi and ,
  • Stefania Villani,
  • Carola Esposito Corcione,
  • Pietro Alifano,
  • Marta Madaghiele and
  • Christian Demitri
  • + 4 authors+ 0 author

The clinical reliability of swabs is affected by their ability to collect and elute biological samples for further detection. Since elution is particularly critical for swab functionality, the goal of this work was to develop a nasopharyngeal swab pr...

(This article belongs to the Topic Additive Manufacturing: From Promise to Practice)
  • Article
  • Open Access
1 Citations
2,280 Views
21 Pages

Our investigation delves into the scaling law governing planetary cratering impacts. We meticulously analyze the interplay between dimensionless parameters driving crater growth and the morphological transition of craters and construct the scaling an...

(This article belongs to the Section Astronautics & Space Science)
  • Article
  • Open Access
2 Citations
2,705 Views
21 Pages

Methodology Proposal, Virtual Simulations and 3D Printed Prototype of a Car Steering Wheel

  • Miriam Fandáková,
  • Pavol Kudela,
  • Maroš Jakubec and
  • Eva Lieskovská

31 December 2024

The design and production of car steering wheel prototypes have evolved significantly with advancements in virtual and additive manufacturing technologies. This study presents a comprehensive methodology for the development of a car steering wheel pr...

(This article belongs to the Section Additive Manufacturing Technologies)
  • Article
  • Open Access
578 Views
19 Pages

The scaled model test is currently the most reliable approach for the conceptual design and experimental validation of floating offshore wind turbines (FOWT). In current scaled model tests, the common practice of designing scaled blades using low-Rey...

(This article belongs to the Section Ocean Engineering)
  • Article
  • Open Access
10 Citations
4,442 Views
27 Pages

Prototyping and Experimental Investigation of Digital Hydraulically Driven Knee Exoskeleton

  • Rituraj Rituraj,
  • Rudolf Scheidl,
  • Peter Ladner,
  • Martin Lauber and
  • Andreas Plöckinger

19 November 2022

Digital hydraulic drives are known for their superior efficiency, power density, and robustness. Such advantages make them an attractive alternative (to electric drives) for actuation of exoskeleton devices. This work presents development of a protot...

(This article belongs to the Special Issue Application and Analysis in Fluid Power Systems)
  • Article
  • Open Access
6 Citations
4,038 Views
20 Pages

18 January 2025

This paper focuses on the experimental testing and characterisation of two designed and constructed prototypes of a human knee joint mechanism. The aim of the mechanical systems, presented as kinematic diagrams and 3D CAD drawings, is to reproduce th...

(This article belongs to the Special Issue Selected Papers from MEDER 2024: Advances of Mechanism Design for Robotic Machines)
  • Article
  • Open Access
13 Citations
4,886 Views
22 Pages

Experimental Study of a Heat Pump for Simultaneous Cooling and Desalination by Membrane Distillation

  • Ahmadou Tidiane Diaby,
  • Paul Byrne,
  • Patrick Loulergue,
  • Ousmane Sow and
  • Thierry Maré

23 September 2021

Heat pump systems can simultaneously produce cooling energy for space cooling in hotels, office and residential buildings and heat for desalination using membrane distillation (MD). The MD technique uses a heat input at a temperature compatible with...

(This article belongs to the Special Issue Advanced Membrane Processes in Water Treatment)
  • Feature Paper
  • Article
  • Open Access
4 Citations
5,471 Views
18 Pages

This paper describes the development and the realization of an adaptive antenna based on a reconfigurable parasitic structure. The geometry of the proposed antenna is circular, and it is composed by an active omni-directional radiator, surrounded by...

(This article belongs to the Special Issue Reconfigurable Antennas)
  • Article
  • Open Access
2 Citations
2,101 Views
25 Pages

Operating Properties of Deep Hole Boring Tools with Modified Design

  • Norbert Kępczak,
  • Grzegorz Bechciński and
  • Radosław Rosik

28 March 2024

This paper presents the results of research work on the revised design of a deep hole boring tool. The study was divided into three stages: theoretical, experimental and operational. In the theoretical part, a 3D model of the actual boring bar was cr...

(This article belongs to the Section Manufacturing Processes and Systems)
  • Article
  • Open Access
12 Citations
8,426 Views
21 Pages

26 February 2021

Serious Games (SG) provide a comfortable learning environment and are productive for various disciplines ranging from Science, Technology, Engineering, and Mathematics (STEM) to computer programming. The Object Oriented (OO) paradigm includes objects...

(This article belongs to the Special Issue Future Trends in Computer Programming Education)
  • Article
  • Open Access
11 Citations
5,902 Views
15 Pages

Modeling of a Field-Modulated Permanent-Magnet Machine

  • Xianglin Li,
  • K. T. Chau and
  • Yubin Wang

19 December 2016

In this work, an effective field-modulated permanent-magnet (FMPM) machine was investigated, in which the spoke-magnet outer rotor and open-slot stator were employed. The objective of this paper is to provide the mathematical modeling analysis that w...

(This article belongs to the Special Issue Electric Machines and Drives for Renewable Energy Harvesting)
  • Article
  • Open Access
3,022 Views
28 Pages

Design and Modeling of a Scaled Drone Prototype for Validation of Reusable Rocket Control Strategies

  • Juan David Daza Flórez,
  • Gabriel Andrés Payanene Zambrano and
  • Sebastián Roa Prada

2 September 2025

This paper presents the development, modeling, and validation of a scaled UAV-VTOL low-cost prototype equipped with a jet propulsion system with vertical take-off and landing capabilities. The prototype is designed as an experimental testbed for reus...

  • Article
  • Open Access
5 Citations
2,365 Views
12 Pages

Design of a Prototypical Mock-Up for the Experimental Investigation of WCLL First-Wall Performances

  • Pietro Maccari,
  • Pietro Arena,
  • Ranieri Marinari,
  • Amelia Tincani and
  • Alessandro Del Nevo

8 February 2023

A large research effort is currently ongoing within the framework of the EUROfusion consortium for the study and design of a water-cooled lithium–lead (WCLL) breeding blanket (BB). This concept will be tested in ITER through the installation of...

(This article belongs to the Special Issue Water Coolant Lithium Lead Breeding Blanket and Test Blanket Module: Design and R&D Activities in 2022)
  • Article
  • Open Access
4 Citations
3,027 Views
19 Pages

Experimental Behaviour of Tensioner for Rigid Hangers of Arch Bridges

  • Michele Fabio Granata,
  • Benedetta Fontana,
  • Marco Rosone and
  • Giovanni Culotta

In steel tied arch bridges where the hangers are made of rigid bars, the replacement of damaged hangers is rather complex. In fact, while generally the cable hangers are already prepared with anchors at the ends and their replacement traces the initi...

(This article belongs to the Topic Resilient Civil Infrastructure)
  • Article
  • Open Access
13 Citations
8,368 Views
25 Pages

2 May 2021

The purpose of the present work was to design, optimize, and test an innovative suspension system for race cars. The study was based on a comprehensive approach that involved conceptual design, modeling, simulation and optimization, and development a...

(This article belongs to the Section Mechanical Engineering)
  • Feature Paper
  • Article
  • Open Access
13 Citations
5,542 Views
26 Pages

25 May 2022

Elastic timber gridshells are lightweight structures whose stiffness is highly dependent on multiple factors, such as boundary conditions and the semi-rigidity and eccentricity of the joints. Their structural analysis requires calibrated numerical mo...

(This article belongs to the Section Civil Engineering)
  • Article
  • Open Access
91 Views
19 Pages

5 November 2026

Thermoplastic polyurethane (TPU) filaments are increasingly used in additively manufactured structures that require large deformation and flexible mechanical response. In this study, the mechanical behavior of TPU-95A filament was experimentally char...

(This article belongs to the Section Polymer Analysis and Characterization)
  • Article
  • Open Access
4 Citations
4,211 Views
20 Pages

16 October 2020

The paper is a continuation of our work on the dynamic load in piezoelectric pumps. In the study, the dynamic load of liquid in the pipelines was proposed as a key factor that limits the output performance of piezoelectric pumps. To decrease the dyna...

(This article belongs to the Section Electronic Sensors)
  • Article
  • Open Access
16 Citations
7,161 Views
17 Pages

29 June 2016

We present here—designed, manufactured, and tested by our research team—the Ti-alloy prototype of the multispiked connecting scaffold (MSC-Scaffold) interfacing the components of resurfacing arthroplasty (RA) endoprostheses with bone. The spikes of t...

(This article belongs to the Section Biomaterials)
  • Article
  • Open Access
598 Views
18 Pages

27 June 2026

This study presents the prototype manufacturing and experimental validation of a 1 kW, 750 rpm three-phase outer-rotor permanent magnet-assisted synchronous reluctance motor (PMASynRM) designed for in-wheel electric vehicle applications. The work is...

(This article belongs to the Special Issue New Advances in Synchronous Reluctance Motors)

of 40