Rechargeable aqueous Zn-ion batteries (ZIBs) have gained great attention due to their high safety and the natural abundance of Zn. Unfortunately, the Zn metal anode suffers from dendrite growth due to nonuniform deposition during the plating/strippin...
Lithium metal batteries are emerging as the next generation of high-density electrochemical energy storage systems because of the ultra-high specific capacity and ultra-low electrochemical potential of the Li metal anode. However, the uneven Li depos...
Al-doped ZnO combines high transparency and conductivity with abundant and non-toxic elements; making it suitable for optoelectronic devices with large-scale applications. In order to check the quality of the material deposited over large areas, spec...
The main objective of this investigation was to study the implications of incorporating zinc oxide nanoparticles into the matrix of a bioactive glass for the bioactivity and structural properties of the deposited coating. ZnO-containing bioactive gla...
The dynamic growth of MOCVD-grown ZnO thin films under temperature effect was systematically investigated by a numerical approach using computational fluid dynamics (CFD) technique. A three-dimensional (3D) reactor-scale model was developed to determ...
Aqueous zinc ion batteries (AZIBs) have considerable potential for energy storage owing to their cost-effectiveness, safety, and environmental sustainability. However, dendrite formation, hydrogen evolution reaction (HER), and corrosion of the bare z...
The influence of ZnO nanolayers as a passivating layer prevents electrons from recombining with the electrolyte or oxidized dye molecules at the interface by acting as a blocking layer for semiconducting materials. At 300 °C, it was observed that...
High transmittance ratio in visible range, low resistivity, and high mobility of IGZO thin films were prepared at room temperature for 30 min by co-sputtering of Zn2Ga2O5 (Ga2O3 + 2 ZnO, GZO) ceramic and In2O3 ceramic at the same time. The deposition...
This paper presents a cost-effective and versatile pico-dispensing technique as an efficient and straightforward approach for depositing zinc oxide nanoparticle (ZnO—NP) thin films on micromechanical devices (MEMS). Due to its piezoelectric pro...
Aerosol deposition (AD) is a simple, dry raw-powder deposition process in which the targeted film is formed by direct bombardment of accelerated starting powder onto the substrate surface at room temperature. Despite the increased interest in AD film...
The effects of zinc and sodium hydroxide concentrations in an alkaline non-cyanide zinc bath on the electrodeposition characteristics of zinc deposits are systematically investigated. Using microstructural and phase analyses of specimens with specifi...
Uncontrollable Zn dendrite formations and parasitic side reactions on Zn electrodes induce poor cycling stability and safety issues, preventing the large-scale commercialization of Zn-ion batteries. Herein, to achieve uniform Zn deposition and suppre...
Electroless deposition on zinc and its alloys is challenging because of the negative standard potential of zinc, the formation of poor surface layers during oxidation in aqueous solutions, and extensive hydrogen evolution. Therefore, there are only f...
Zinc sulfide (ZnS) thin films prepared using the chemical bath deposition (CBD) method have demonstrated great viability in various uses, encompassing photonics, field emission devices, field emitters, sensors, electroluminescence devices, optoelectr...
The efficiency of thin-film chalcogenide solar cells is dependent on their window layer thickness. However, the application of an ultrathin window layer is difficult because of the limited capability of the deposition process. This paper reports the...
In this study, pure ZnO and Al-doped ZnO(AZO) thin films were coated onto a SiO2 wafer using the electrostatic spray deposition (ESD) process for acetone gas detection under laboratory conditions. Voltage levels were varied to determine the optimal c...
Thin films of nanocomposite of zinc oxide–reduced graphene oxide (ZnO-rGO) deposited on soda-lime glass substrates were prepared using ultrasonic spray pyrolysis (USP) at 460 °C. The preparation process does not use harsh acids and is envir...
In this study, we utilized a sapphire substrate with a matrix protrusion structure as a template. We employed a ZnO gel as a precursor and deposited it onto the substrate using the spin coating method. After undergoing six cycles of deposition and ba...
The flexible transparent conductive films (TCFs) of a ZnS/Cu/Ag/TiO2 multilayered structure were deposited on a flexible PET substrate with high surface roughness using magnetic sputtering, and the effects of structural characteristics on the perform...
We study the effect of thermal annealing on the electrical properties of the nanoscale p-n heterojunctions based on single n-type ZnO nanorods on p-type GaN substrates. The ZnO nanorods are prepared by chemical bath deposition on both plain GaN subst...
In this present work, we have successfully synthesized vertical aligned ZnO nanorod arrays (ZnO NRs) on conductive stainless-steel substrate. These ZnO NRs were obtained by using a low temperature, low cost, and eco-friendly hydrothermal approach. Th...
Zinc oxide (ZnO) nanorods grown by chemical bath deposition (CBD) on the surface of polyetheresulfone (PES) electrospun fibers confer antimicrobial properties to the obtained hybrid inorganic–polymeric PES/ZnO mats. In particular, a decrement o...
ZnO thin-film ultraviolet photodetectors are widely used in the military, space, environmental protection, medicine, and other fields. Accurate printing of ZnO photoelectric-sensitive films plays a key role in the detection results. Therefore, obtain...
To address the uneven deposition of zirconium conversion coatings on multiphase 55AlZnMg under short pretreatment cycles, this study investigated the time-dependent formation behavior of ZrCC in a selected H2ZrF6 bath. By precisely controlling the im...
Aqueous zinc-ion batteries (AZIBs) have emerged as highly promising options for large-scale energy storage systems due to their cost-effectiveness, substantial energy capacity, and improved safety features. However, the Zn anode faces challenges such...
Zinc (Zn) coating is being used to protect steel structures from corrosion. There are different processes to deposit the coating onto a steel substrate. Therefore, in the present study, a 100 µm thick Zn coating was deposited by arc and plasma...
The spin-coating method has been employed for nanostructured crystalline zinc oxide (ZnO) thin film preparation on FTO glass substrates. Cadmium sulfide (CdS) layers were then deposited on the surface via the chemical bath deposition method. To inves...
Cu-ZnO-based catalysts are of importance for CO2 utilization to synthesize methanol. However, the mechanisms of CO2 activation, the split of the C=O double bond, and the formation of C-H and O-H bonds are still debatable. To understand this mechanism...
This research presents the development and characterization of a semi-automatic electrophoretic deposition (EPD) system designed for the synthesis of zinc oxide (ZnO) microstructures, utilizing a bioinspired neuro-fuzzy control strategy (ANFIS). The...
This study used a rapid and simple microwave-assisted synthesis method to grow ZnO nanoneedle arrays on the silicon substrate with the ZnO seed layer. The effects of reaction temperature and time on the lengths of ZnO nanoneedle arrays were investiga...
Herein, we synthesized the zinc oxide (ZnO) thin films (TFs) deposited on glass substrates via spray pyrolysis (SP) to prepare self-cleaning glass. Various process parameters were used to optimize photocatalytic performance. Substrates were coated at...
Cu2ZnSnS4 (CZTS) is a complex quaternary material, and obtaining a single-phase CZTS with no secondary phases is known to be challenging and dependent on the production technique. This work involves the synthesis and characterization of CZTS absorber...
Indium phosphide nanowires (InP NWs) are accessible at 440 °C from a novel vapor phase deposition approach from crystalline InP sources in hydrazine atmospheres containing 3 mol % H2O. Uniform zinc blende (ZB) InP NWs with diameters around 20 nm and...
This paper establishes the optimal thickness of TiN ceramic coating on the surface of Mg-Ca-Zn alloy using optical and scanning microscopy methods. X-ray diffraction analysis and tests on its mechanical properties showed that deposition of coating wi...
Substitutions of ions into an apatitic lattice may result in antibacterial properties. In this study, magnesium (Mg)-, zinc (Zn)-, and silicon (Si)-substituted hydroxyapatite (HA) were synthesized using a microwave irradiation technique. Polyvinyl al...
Transparent conductive oxide (TCO) layers, to be implemented in photo-anodes for dye-sensitized solar cells (DSCs), were prepared by co-deposition of ZnO and Al using pulsed-direct current (DC)-magnetron reactive sputtering processes. The films were...
Aqueous zinc ion batteries are highly sought after for the next generation of sustainable energy storage systems. However, their development is significantly impeded by the presence of undesired zinc dendrites, which greatly reduce their cycle life....
The Lanuoma sediment-hosted lead–zinc (Pb–Zn) deposit, situated in the central part of the Sanjiang base metal metallogenic belt (SMB) within the Changdu Basin, is hosted by Triassic Bolila Formation limestone. The source of metals and su...
In the Bazhenovskoye chrysotile–asbestos deposit (Middle Urals), nephrite bodies of the serpentinite type were found on the contact of after gabbro rodingites and serpentinites. The color is uniform to non-uniform, green to light green, bluish green,...
Results of comparative structural characterization of bare and Zn-covered ZnTe nanowires (NWs) before and after thermal oxidation at 300 °C are presented. Scanning electron microscopy, energy-dispersive X-ray spectroscopy, high-resolution transmissio...
Buckypaper (BP), a flexible and porous material, exhibits photovoltaic properties when exposed to light. In this study, we employed radio frequency (RF) sputtering of zinc oxide (ZnO) followed by rapid thermal annealing to enhance the photovoltaic re...
This work investigated the structural, morphological, electrical and photovoltaic properties of n-ZnNiO/p-Si heterostructures. ZnNiO nanocomposite thin films were fabricated on p-Si (100) substrates using pulsed laser deposition, enabling the formati...
In this paper, we demonstrate the significant impact of the solution flow and electrical field on the homogeneity of large-scale ZnO nanorod electrodeposition from an aqueous solution containing zinc nitrate and ammonium nitrate, primarily based on t...
Amorphous oxide semiconductors (AOSs) are interesting materials which combine optical transparency with high electron mobility. AOSs can be prepared at low temperatures by high throughput deposition techniques such as magnetron sputtering and are thu...
Zn-substituted hydroxyapatite with antibacterial effect was used in radiofrequency (RF) magnetron deposition of calcium phosphate coating onto Ti- and Si-inclined substrates. The development of surface nanopatterns for direct bacteria killing is a gr...
The physical properties of ZnO can be tuned efficiently and controllably by doping with the proper element. Doping of ZnO thin films with 3D transition metals that have unpaired electron spins (e.g., Fe, Co, Ni, etc.) is of particular interest as it...
Aqueous rechargeable zinc-ion batteries (ARZIBs) are potential candidates for grid-scale energy storage applications. In addition to its reversible chemistry in aqueous electrolytes, Zn metal is stable in water and air. However, there are critical ch...
The Wunuer deposit is an important hydrothermal Zn-Pb-Ag-Mo polymetallic deposit in the central Great Xing’an Range, NE China. The zinc–lead polymetal mineralization is closely hosted by the volcanic rocks of the Manketouebo formation (rh...
Aqueous zinc−ion batteries (ZIBs) are widely recognized as highly promising energy storage devices because of their inherent characteristics, including superior safety, affordability, eco−friendliness, and various other benefits. However,...
Pulsed laser deposition (PLD) is widely used for functional film fabrication, but traditional nanosecond-laser-induced thermal effects and interface roughness severely limit the quality of multilayer structures. To address this critical challenge, a...
of 4