Skip to Content

73 Results Found

  • Article
  • Open Access
7 Citations
3,842 Views
25 Pages

A Study of Particle Heating and Oxidation Protection in a Modified Internally Injected Ar–H2 Atmospheric Plasma Spraying Torch

  • Mahrukh Mahrukh,
  • Sen-Hui Liu,
  • Li Zhang,
  • Sohail Husnain and ,
  • Cheng-Chung Yang,
  • Xiao-Tao Luo and
  • Chang-Jiu Li
  • + 2 authors+ 0 author

13 February 2025

This study employs computational fluid dynamics (CFD) to analyze the in-flight dynamics of particles in an Ar–H2 atmospheric plasma spray (APS) torch with a modified diverging-type nozzle. The focus is on optimizing injection parameters—p...

  • Article
  • Open Access
261 Views
19 Pages

27 October 2026

Soft pneumatic actuators (SPAs) are widely applied in soft robots for their good compliance and environmental adaptability. However, conventional SPAs with a single prescribed deformation mode provide limited dexterity for tasks requiring reconfigura...

(This article belongs to the Special Issue Soft Actuators and Robotics—2nd Edition)
  • Article
  • Open Access
4 Citations
1,526 Views
23 Pages

17 June 2025

The influence of multiwall carbon nanotube (MWCNT) reinforcements on electrochemical corrosion investigations at varying NaCl concentrations (0.4 M, 0.6 M, 0.8 M, 1 M) of Mg-Zn-Ce nanocomposites is studied in this work. The Mg-Zn-Ce/MWCNT nanocomposi...

(This article belongs to the Special Issue Advances in Corrosion and Protection of Materials (Third Edition))
  • Article
  • Open Access
4 Citations
2,514 Views
24 Pages

In this paper, a new sacrificial cladding with foam concrete-filled square tubes (FCFST sacrificial cladding) was developed for dissipating impact energy. The impact experiment was conducted on the FCFST sacrificial claddings using a drop hammer impa...

(This article belongs to the Section Building Materials, and Repair & Renovation)
  • Article
  • Open Access
7,686 Views
19 Pages

1 February 2023

Qixiang is a unique sacrificial culture created by the Han army eight banners in northeast China. This culture not only has elements such as shamanism and Han people burning incense, but also has military sacrificial elements. This paper argues that...

(This article belongs to the Special Issue The Revitalization of Shamanism in Contemporary China)
  • Article
  • Open Access
6 Citations
2,181 Views
12 Pages

8 February 2024

Cathodic protection is widely used for metal corrosion protection. To improve their performance, it is necessary and urgent to study the influence of metal oxides on the microstructure and performance of aluminum alloy sacrificial anodes. Taking an A...

(This article belongs to the Special Issue Additive Manufacturing of Aluminum Alloys and Aluminum Matrix Composites)
  • Article
  • Open Access
14 Citations
5,683 Views
21 Pages

16 January 2023

This study aims to analyze the longitudinal seismic performance of a typical multi-span continuous girder bridge with seat-type abutments under earthquake excitation, especially accounting for different abutment behaviors. Three-dimensional finite el...

(This article belongs to the Special Issue Recent Developments in Vibration Control and Monitoring of Civil Structures)
  • Article
  • Open Access
16 Citations
6,622 Views
14 Pages

Emissions Characteristics of Hazardous Air Pollutants from the Incineration of Sacrificial Offerings

  • Shihao Zhang,
  • Lianhong Zhong,
  • Xi Chen,
  • Yanan Liu and ,
  • Xiaoman Zhai,
  • Yifeng Xue,
  • Wei Wang,
  • Jie Liu and
  • Kangli Xu
  • + 4 authors+ 0 author

18 June 2019

The incineration of sacrificial offerings generates numerous hazardous air pollutants, including particulate matter (PM), CO, SO2, NOx and non-methane hydrocarbons (NMHC), which has significant effects on the environment and human health. However, du...

  • Article
  • Open Access
15 Citations
5,203 Views
17 Pages

7 March 2021

The utilization of sacrificial layers to strengthen civilian structures against terrorist attacks is of great interest to engineering experts in structural retrofitting. The sacrificial cladding structures are designed to be attached to the façade of...

(This article belongs to the Section Modelling in Engineering Structures)
  • Article
  • Open Access
7 Citations
3,054 Views
16 Pages

31 January 2020

Mimicking natural structures has been highly pursued recently in composite structure design to break the bottlenecks in the mechanical properties of the traditional structures. Bone has a remarkable comprehensive performance of strength, stiffness an...

  • Article
  • Open Access
8 Citations
3,350 Views
20 Pages

15 September 2022

The defense effects of sacrificial cladding have been extensively studied in the field of blast resistance. As a polymer material with a cellular structure, polyurethane also has the potential to act as sacrificial cladding due to its good mechanical...

(This article belongs to the Special Issue Recent Developments in Geopolymer Composites)
  • Article
  • Open Access
10 Citations
5,797 Views
12 Pages

Fabrication of Magnetically Driven Microvalve Arrays Using a Photosensitive Composite

  • Tasuku Nakahara,
  • Junya Suzuki,
  • Yuki Hosokawa,
  • Fusao Shimokawa and ,
  • Hidetoshi Kotera and
  • Takaaki Suzuki
  • + 1 author+ 0 author

Microvalves play an important role in fluid control in micro total analysis systems (µTAS). Previous studies have reported complex fabrication processes for making microvalve elements in a channel. Hence, there is a need for a simpler microvalve fabr...

  • Feature Paper
  • Article
  • Open Access
2 Citations
6,943 Views
7 Pages

Free-Standing GaMnAs Nanomachined Sheets for van der Pauw Magnetotransport Measurements

  • Jae-Hyun Lee,
  • Seondo Park,
  • Chanuk Yang,
  • Hyung Kook Choi and ,
  • Myung Rae Cho,
  • Sung Un Cho and
  • Yun Daniel Park
  • + 2 authors+ 0 author

9 December 2016

We report on the realization of free-standing GaMnAs epilayer sheets using nanomachining techniques. By optimizing the growth conditions of the sacrificial Al0.75Ga0.25As layer, free-standing metallic GaMnAs (with ~6% Mn) microsheets (with TC ~85 K)...

  • Article
  • Open Access
12 Citations
3,079 Views
19 Pages

Blast Alleviation of Sacrificial Cladding with Graded and Uniform Cellular Materials

  • Yuanyuan Ding,
  • Yuxuan Zheng,
  • Zhijun Zheng,
  • Yonggang Wang and ,
  • Siyuan He and
  • Fenghua Zhou
  • + 1 author+ 0 author

9 December 2020

Graded cellular material is a superb sandwich candidate for blast alleviation, but it has a disadvantage for the anti-blast design of sacrificial cladding, i.e., the supporting stress for the graded cellular material cannot maintain a constant level....

  • Abstract
  • Open Access
4,032 Views
3 Pages

Screen-Printed Ceramic MEMS for Metal Oxide Gas Sensor

  • Oleg Kul,
  • Alexey Vasiliev,
  • Andrey Nikitin,
  • Anna Dmitrieva and
  • Alexandr Bolshakov

We developed a new approach to the fabrication of MEMS (Microelectromechanical system) substrates for gas sensors. This full screen-printing approach consists in the application of sacrificial material, which is solid at the near-room temperature of...

(This article belongs to the Proceedings of XXXV EUROSENSORS Conference)
  • Article
  • Open Access
19 Citations
6,835 Views
12 Pages

Thin Film Encapsulation for RF MEMS in 5G and Modern Telecommunication Systems

  • Anna Persano,
  • Fabio Quaranta,
  • Antonietta Taurino,
  • Pietro Aleardo Siciliano and
  • Jacopo Iannacci

10 April 2020

In this work, SiNx/a-Si/SiNx caps on conductive coplanar waveguides (CPWs) are proposed for thin film encapsulation of radio-frequency microelectromechanical systems (RF MEMS), in view of the application of these devices in fifth generation (5G) and...

(This article belongs to the Section Physical Sensors)
  • Article
  • Open Access
6 Citations
3,719 Views
28 Pages

Cost-Effective Corrosion Detection Sensor for Above-Ground Oil and Gas Flowlines

  • Nader Vahdati,
  • Oleg Shiryayev,
  • Shahid M. Parapurath,
  • Fook F. Yap and
  • Haider Butt

4 November 2022

A sensor for monitoring of the external corrosion of small-diameter aboveground oil and gas pipelines (called flowlines), based on fiber-optic strain sensing, is proposed. The working principle of our proposed sensor relies on the use of a pre-stress...

(This article belongs to the Special Issue Sensors for Vibration Control and Structural Health Monitoring)
  • Article
  • Open Access
12 Citations
3,397 Views
18 Pages

3 February 2020

Extensive research focus had been given to sacrificial sandwich panels to mitigate the effects of blast loads. This is due to their ability to distribute the load and absorb a significant portion of the blast energy. This paper studies the behavior o...

  • Article
  • Open Access
5 Citations
4,805 Views
17 Pages

Cold Sintering of PZT 2-2 Composites for High Frequency Ultrasound Transducer Arrays

  • Shruti Gupta,
  • Dixiong Wang,
  • Smitha Shetty,
  • Amira Meddeb and ,
  • Sinan Dursun,
  • Clive A. Randall and
  • Susan Trolier-McKinstry
  • + 2 authors+ 0 author

13 September 2021

Medical ultrasound and other devices that require transducer arrays are difficult to manufacture, particularly for high frequency devices (>30 MHz). To enable focusing and beam steering, it is necessary to reduce the center-to-center element spaci...

(This article belongs to the Section Actuator Materials)
  • Feature Paper
  • Article
  • Open Access
1,784 Views
16 Pages

Effect of SRB on the Electrochemical Performance of Aluminum-Based Sacrificial Anodes in Marine Mud

  • Baocheng Zhou,
  • Wei Zhang,
  • Xinwen Zhang,
  • Weiyin Quan and ,
  • Hua Huang and
  • Zhifeng Lin
  • + 1 author+ 0 author

25 December 2025

This study investigated the degradation of aluminum-based sacrificial anodes caused by sulfate-reducing bacteria (SRB) in marine mud. Through self-discharge tests simulating real cathodic protection conditions, alongside macroscopic observations, ele...

(This article belongs to the Special Issue Investigation on Structure and Corrosion Resistance of Steels/Alloys, 2nd Edition)
  • Article
  • Open Access
10 Citations
5,862 Views
13 Pages

This article presents a new wafer-bonding fabrication technique for Capacitive Micromachined Ultrasonic Transducers (CMUTs) using polymethyl methacrylate (PMMA). The PMMA-based single-mask and single-dry-etch step-bonding device is much simpler, and...

(This article belongs to the Section A: Physics)
  • Article
  • Open Access
8 Citations
6,896 Views
13 Pages

Large Out-of-Plane Displacement Bistable Electromagnetic Microswitch on a Single Wafer

  • Xiaodan Miao,
  • Xuhan Dai,
  • Yi Huang,
  • Guifu Ding and
  • Xiaolin Zhao

5 May 2016

This paper presents a bistable microswitch fully batch-fabricated on a single glass wafer, comprising of a microactuator, a signal transformer, a microspring and a permanent magnet. The bistable mechanism of the microswitch with large displacement of...

(This article belongs to the Special Issue Modeling, Testing and Reliability Issues in MEMS Engineering)
  • Article
  • Open Access
14 Citations
7,029 Views
14 Pages

Formation of Micro and Mesoporous Amorphous Silica-Based Materials from Single Source Precursors

  • Mohd Nazri Mohd Sokri,
  • Yusuke Daiko,
  • Zineb Mouline,
  • Sawao Honda and
  • Yuji Iwamoto

Polysilazanes functionalized with alkoxy groups were designed and synthesized as single source precursors for fabrication of micro and mesoporous amorphous silica-based materials. The pyrolytic behaviors during the polymer to ceramic conversion were...

(This article belongs to the Special Issue Mesoporous Materials)
  • Review
  • Open Access
10 Citations
6,290 Views
24 Pages

Selective Ultrasonic Gravimetric Sensors Based on Capacitive Micromachined Ultrasound Transducer Structure—A Review

  • Dovydas Barauskas,
  • Mindaugas Dzikaras,
  • Dovydas Bieliauskas,
  • Donatas Pelenis and ,
  • Gailius Vanagas and
  • Darius Viržonis
  • + 1 author+ 0 author

23 June 2020

This review paper discusses the advances of the gravimetric detection devices based on capacitive micromachined ultrasound transducers structure. Principles of gravimetric operation and device modeling are reviewed through the presentation of an anal...

(This article belongs to the Special Issue Modeling, Development and Applications of Novel Ultrasound Sensors)
  • Article
  • Open Access
22 Citations
4,645 Views
17 Pages

The cable system is an important bearing element of a bridge with stay cables or slings and a matter of major concern in the safety of the bridge structure. Bridge cables are vulnerable to corrosion induced by leakage and soaking during their service...

  • Article
  • Open Access
13 Citations
3,888 Views
17 Pages

The Effect of Increasing the Amount of Indium Alloying Material on the Efficiency of Sacrificial Aluminium Anodes

  • Krzysztof Zakowski,
  • Juliusz Orlikowski,
  • Kazimierz Darowicki,
  • Marcin Czekajlo and ,
  • Piotr Iglinski and
  • Kinga Domanska
  • + 1 author+ 0 author

2 April 2021

Al-Zn-In alloys having 4.2% zinc content and various indium content in the range of 0.02–0.2% were tested with respect to the most important electrochemical properties of sacrificial anodes in a cathodic protection, i.e., the current capacity and pot...

(This article belongs to the Section Corrosion)
  • Article
  • Open Access
18 Citations
5,153 Views
12 Pages

24 April 2021

Doping heteroatoms such as nitrogen (N) and boron (B) into the framework of carbon materials is one of the most efficient methods to improve the electrical performance of carbon-based electrodes. In this study, N-doped carbon has been facilely synthe...

(This article belongs to the Special Issue Advanced Materials and Technologies for Lithium-Ion Battery)
  • Article
  • Open Access
3 Citations
3,641 Views
18 Pages

Multi-Layer and Conformally Integrated Structurally Embedded Vascular Antenna (SEVA) Arrays

  • Amrita Bal,
  • Jeffery W. Baur,
  • Darren J. Hartl,
  • Geoffrey J. Frank and ,
  • Thao Gibson,
  • Hong Pan and
  • Gregory H. Huff
  • + 2 authors+ 0 author

4 March 2021

This work presents the design and fabrication of two multi-element structurally embedded vascular antennas (SEVAs). These are achieved through advances in additively manufactured sacrificial materials and demonstrate the ability to embed vascular mic...

(This article belongs to the Special Issue Applications of Antenna Technology in Sensors)
  • Proceeding Paper
  • Open Access
2,250 Views
5 Pages

Silicon-On-Nothing Micro-Pirani Gauge for Interior-Pressure Measurement

  • Andrey Kravchenko,
  • Vladislav Komenko and
  • Wolf-Joachim Fischer

20 November 2018

In the current work, we present a compact and cost effective Pirani gauge based on Silicon-On-Nothing (SON) technology. The proposed design uses an innovative approach of etching the sensing element directly in a crystalline silicon membrane. Such co...

(This article belongs to the Proceedings of EUROSENSORS 2018)
  • Article
  • Open Access
5 Citations
4,025 Views
20 Pages

Novel Fabrication Technology for Clamped Micron-Thick Titanium Diaphragms Used for the Packaging of an Implantable MEMS Acoustic Transducer

  • Lukas Prochazka,
  • Alexander Huber,
  • Michael Schneider,
  • Naureen Ghafoor and ,
  • Jens Birch and
  • Flurin Pfiffner
  • + 1 author+ 0 author

31 December 2021

Micro-Electro-Mechanical Systems (MEMS) acoustic transducers are highly sophisticated devices with high sensing performance, small size, and low power consumption. To be applied in an implantable medical device, they require a customized packaging so...

(This article belongs to the Special Issue Micromachined Acoustic Transducers for Audio-Frequency Range)
  • Article
  • Open Access
18 Citations
8,756 Views
10 Pages

2 November 2015

The study investigates the design and fabrication of a micromachined radio frequency (RF) capacitive switch using the complementary metal oxide semiconductor-microelectromechanical system (CMOS-MEMS) technology. The structure of the micromachined swi...

(This article belongs to the Special Issue CMOS-MEMS Sensors and Devices)
  • Article
  • Open Access
32 Citations
12,040 Views
11 Pages

9 November 2007

This study presents the simulation, fabrication and characterization ofmicromechanical radio frequency (RF) switch with micro inductors. The inductors areemployed to enhance the characteristic of the RF switch. An equivalent circuit model isdeveloped...

(This article belongs to the Special Issue Modeling, Testing and Reliability Issues in MEMS Engineering)
  • Article
  • Open Access
2 Citations
6,879 Views
11 Pages

17 January 2014

The fabrication and characterization of a radio frequency (RF) micromachined switch with annealing were presented. The structure of the RF switch consists of a membrane, coplanar waveguide (CPW) lines, and eight springs. The RF switch is manufactured...

(This article belongs to the Special Issue Modeling, Testing and Reliability Issues in MEMS Engineering 2013)
  • Article
  • Open Access
32 Citations
4,473 Views
13 Pages

14 November 2019

Two routes of preparation of mesoporous Ni-alumina materials favoring the intermediate formation of nanostructured nickel-aluminate are presented. The first one involves an aluminum containing MOF precursor used as sacrificial template to deposit nic...

(This article belongs to the Special Issue Microporous/Mesoporous Inorganic Materials)
  • Article
  • Open Access
512 Views
17 Pages

As a chemical element, manganese is used in a wide range of industries, particularly steelmaking and creating alloys and as a sacrificial coating for corrosion protection. Electrodeposition is a low-energy process; however, manganese electrodepositio...

(This article belongs to the Section Corrosion, Wear and Erosion)
  • Article
  • Open Access
1,557 Views
22 Pages

Fabrication and Properties of Zn-Containing Intermetallic Compounds as Sacrificial Anodes of Zn-Based Implants

  • Kelei Li,
  • Junwei Li,
  • Tiebao Wang,
  • Xin Wang and ,
  • Yumin Qi,
  • Lichen Zhao and
  • Chunxiang Cui
  • + 2 authors+ 0 author

30 April 2025

In the field of degradable metals, Zn-based implants have gradually gained more attention. However, the relatively slow degradation rate compared with the healing rate of the damaged bone tissue, along with the excessive Zn2+ release during the degra...

(This article belongs to the Special Issue Physical Metallurgy of Metals and Alloys (3rd Edition))
  • Article
  • Open Access
21 Citations
8,663 Views
13 Pages

A CMOS Pressure Sensor Tag Chip for Passive Wireless Applications

  • Fangming Deng,
  • Yigang He,
  • Bing Li,
  • Lei Zuo and ,
  • Xiang Wu and
  • Zhihui Fu
  • + 1 author+ 0 author

23 March 2015

This paper presents a novel monolithic pressure sensor tag for passive wireless applications. The proposed pressure sensor tag is based on an ultra-high frequency RFID system. The pressure sensor element is implemented in the 0.18 µm CMOS process and...

(This article belongs to the Section Physical Sensors)
  • Article
  • Open Access
25 Citations
14,768 Views
15 Pages

19 November 2008

This paper discusses sputtered silicon encapsulation as a wafer level packaging approach for isolatable MEMS devices. Devices such as accelerometers, RF switches, inductors, and filters that do not require interaction with the surroundings to functio...

(This article belongs to the Special Issue Modeling, Testing and Reliability Issues in MEMS Engineering)
  • Article
  • Open Access
3 Citations
7,008 Views
12 Pages

Ultra-Thin Platinum Deposits by Surface-Limited Redox Replacement of Tellurium

  • Fatima Haidar,
  • Mathieu Maas,
  • Andrea Piarristeguy,
  • Annie Pradel and ,
  • Sara Cavaliere and
  • Marie-Christine Record
  • + 1 author+ 0 author

15 October 2018

Platinum is the most employed electrocatalyst for the reactions taking place in energy converters, such as the oxygen reduction reaction in proton exchange membrane fuel cells, despite being a very low abundant element in the earth’s crust and...

(This article belongs to the Special Issue Design and Development of Nanostructured Thin Films)
  • Article
  • Open Access
703 Views
31 Pages

Seismic Energy Dissipation in Bridges for Performance Enhancement

  • Juan M. Mayoral,
  • Mauricio Pérez,
  • Azucena Román-de la Sancha,
  • Ingrid Guzmán and
  • Leomar González

22 April 2026

Modern performance-based bridge design seeks to control damage in specific failure modes in order to balance safety and economy, particularly in high-seismic regions where inelastic and ductile deformation is expected to occur, both in the structure...

  • Article
  • Open Access
18 Citations
5,433 Views
19 Pages

Structure and Electromagnetic Properties of Cellular Glassy Carbon Monoliths with Controlled Cell Size

  • Andrzej Szczurek,
  • Vanessa Fierro,
  • Artyom Plyushch,
  • Jan Macutkevic and ,
  • Polina Kuzhir and
  • Alain Celzard
  • + 1 author+ 0 author

1 May 2018

Electromagnetic shielding is a topic of high importance for which lightweight materials are highly sought. Porous carbon materials can meet this goal, but their structure needs to be controlled as much as possible. In this work, cellular carbon monol...

(This article belongs to the Special Issue Electromagnetic Wave Absorbing Structures)
  • Article
  • Open Access
10 Citations
9,959 Views
21 Pages

Optimal and Robust Design Method for Two-Chip Out-of-Plane Microaccelerometers

  • Sangmin Lee,
  • Hyoungho Ko,
  • Byoungdoo Choi and
  • Dong-il Dan Cho

24 November 2010

In this paper, an optimal and robust design method to implement a two-chip out-of-plane microaccelerometer system is presented. The two-chip microsystem consists of a MEMS chip for sensing the external acceleration and a CMOS chip for signal processi...

(This article belongs to the Section Physical Sensors)
  • Review
  • Open Access
2 Citations
2,505 Views
21 Pages

2 March 2026

This study examines religion as a potent pre-socialisation factor in modern military socialisation, exploring how sacred roots and transcendent anchors influence the formation of military identity. By synthesising Ecological Systems Theory, the Relig...

(This article belongs to the Special Issue The Ethics of War and Peace: Religious Traditions in Dialogue)
  • Proceeding Paper
  • Open Access
3 Citations
2,882 Views
9 Pages

18 February 2025

Gyroid-based mechanical metamaterials have garnered increasing attention for their unique mechanical properties, particularly in applications involving complex stress environments. This study focuses on the mechanical characterization of the gyroid c...

(This article belongs to the Proceedings of The 53rd Conference of the Italian Scientific Society of Mechanical Engineering Design)
  • Article
  • Open Access
282 Views
37 Pages

28 September 2026

Ceramic-matrix-composite (CMC) turbine seal segments lose their gas-side coatings in service. Assessing one loss configuration takes a thermal and a mechanical finite-element solve, and there are too many admissible configurations to solve them all....

  • Review
  • Open Access
165 Citations
15,567 Views
21 Pages

Tissue engineering aims to develop artificial human tissues by culturing cells on a scaffold in the presence of biochemical cues. Properties of scaffold such as architecture and composition highly influence the overall cell response. Electrospinning...

  • Article
  • Open Access
21 Citations
9,726 Views
13 Pages

Integrated Piezoelectric AlN Thin Film with SU-8/PDMS Supporting Layer for Flexible Sensor Array

  • Hong Goo Yeo,
  • Joontaek Jung,
  • Minkyung Sim,
  • Jae Eun Jang and
  • Hongsoo Choi

6 January 2020

This research focuses on the development of a flexible tactile sensor array consisting of aluminum nitride (AlN) based on micro-electro-mechanical system (MEMS) technology. A total of 2304 tactile sensors were integrated into a small area of 2.5 &tim...

(This article belongs to the Special Issue Development of Piezoelectric Sensors and Actuators)
  • Article
  • Open Access
16 Citations
4,601 Views
17 Pages

Embedded Corrosion Sensing with ZnO-PVDF Sensor Textiles

  • Tonoy Chowdhury,
  • Nandika D’Souza,
  • Yee Hsien Ho,
  • Narendra Dahotre and
  • Ifana Mahbub

28 May 2020

Corrosion in underground and submerged steel pipes is a global problem. Coatings serve as an impermeable barrier or a sacrificial element to the transport of corrosive fluids. When this barrier fails, corrosion in the metal initiates. There is a crit...

(This article belongs to the Section Nanosensors)
  • Review
  • Open Access
41 Citations
7,518 Views
20 Pages

Hexavalent chromium (Cr(VI)) is a toxic, mutagenic, teratogenic, and carcinogenic species. Its origin is in industrial activities. Therefore, its effective control is realized on a source basis. Although chemical methods proved effective in removing...

(This article belongs to the Special Issue Chemical-Based Removal of Heavy Metal Ions from Wastewater)
  • Article
  • Open Access
2 Citations
3,031 Views
21 Pages

8 September 2024

This article compares chemical coagulation with electrocoagulation, two popular methods for the primary treatment of wastewater generated in the process of underground coal gasification (UCG). The primary aim was to determine which method is more eff...

(This article belongs to the Special Issue Application of Electrochemical Technology for Water and Wastewater Treatment)

of 2