Skip to Content

167 Results Found

  • Article
  • Open Access
11 Citations
2,614 Views
15 Pages

Profile Control Using Fly Ash Three-Phase Foam Assisted by Microspheres with an Adhesive Coating

  • Yulong Yang,
  • Tingting Cheng,
  • Zhenjiang You,
  • Tuo Liang and
  • Jirui Hou

16 April 2021

Foam-assisted steam flooding is a promising technique to alleviate gas channeling and enhance sweep efficiency in heterogeneous heavy-oil reservoirs. However, long-term foam stabilization remains problematic at high temperatures. Three-phase foam (TP...

(This article belongs to the Special Issue Multiphase Flows in Microfluidics: Fundamentals and Applications)
  • Article
  • Open Access
33 Citations
6,584 Views
19 Pages

17 August 2017

A three-dimensional backfill pipeline transport model is developed using the computational fluid dynamics (CFD) technique, which is applied to study the pipeline transport properties of three-phase foam slurry backfill (TFSB). Based on rheological pr...

(This article belongs to the Special Issue Minerals in Mine Wastes: Contributions to the Circular Economy)
  • Article
  • Open Access
1 Citations
3,133 Views
14 Pages

Numerical Study of the Effects of Surface Tension and Initial Volume Fraction on Gas-Liquid-Foam Three-Phase Flow Separation Process

  • TianTian Tan,
  • Jiaqing Zhang,
  • Junjie Hu,
  • Jianghong Zhang and ,
  • Gang Sun,
  • Bo Li and
  • Yi Guo
  • + 2 authors+ 0 author

13 March 2023

Since it is low in cost and low in toxicity and has good biodegradability, gas-liquid-foam three-phase flow has been widely used in industrial fire protection. Due to the different characteristics of gas, liquid, and foam, liquid precipitation is lia...

(This article belongs to the Special Issue Fire Numerical Simulation)
  • Feature Paper
  • Article
  • Open Access
1 Citations
1,977 Views
17 Pages

Characteristics and Stabilization Mechanism of Three-Phase Foam: Improving Heavy Oil Recovery via Steam Stimulation through Two-Dimensional Visual Model

  • Mingxuan Wu,
  • Zengmin Lun,
  • Yongqiang Tang,
  • Jinming Dai and ,
  • Mingkai Liu,
  • Deqiang Wang and
  • Zhaomin Li
  • + 2 authors+ 0 author

4 September 2023

There is a problem of a rapid decline in production caused by the repeated heating of the near-wellbore zone during steam stimulation. Finding a suitable foam system to expand the area of the steam chamber and slow down the rapid production of hot wa...

(This article belongs to the Special Issue Multiphase Flow, and Efficient Development Methodology and Technology in Unconventional Reservoirs)
  • Article
  • Open Access
20 Citations
4,792 Views
13 Pages

28 April 2018

The dispersed particle gel (DPG) three-phase foam is a novel profile control and flooding system. The stability mechanism of the DPG three-phase foam was studied using an interfacial dilational rheology method. The results show that the elastic modul...

(This article belongs to the Section Advanced Composites)
  • Review
  • Open Access
2 Citations
2,128 Views
28 Pages

25 October 2025

Coal spontaneous combustion causes both human casualties and environmental pollution. Owing to special flow behaviors, foam materials used in fire-fighting technology can effectively bring water and solid non-combustible substances into the fire-figh...

(This article belongs to the Special Issue Foam Materials and Applications)
  • Article
  • Open Access
10 Citations
4,031 Views
19 Pages

8 August 2022

This study develops robust numerical algorithms for the simulation of three-phase (solid-liquid-gas) boiling and bubble formation problems in rectangular channels. The numerical algorithms are based on the Finite Volume Methods (FVM) and implement bo...

(This article belongs to the Section J1: Heat and Mass Transfer)
  • Article
  • Open Access
3 Citations
2,578 Views
24 Pages

10 September 2024

High-temperature geothermal wells frequently employ foam drilling fluids and Polycrystalline Diamond Compact (PDC) drill bits. Understanding the bottom-hole flow field of PDC drill bits in foam drilling is essential for accurately analyzing their hyd...

(This article belongs to the Special Issue Multiphase Flow and Granular Mechanics)
  • Feature Paper
  • Article
  • Open Access
18 Citations
4,841 Views
17 Pages

4 March 2022

The mining and mineral processing of Cu-Ni-PGM sulfide ores in South Africa occurs in semi-arid regions. The scarcity of water resources in these regions has become one of the biggest challenges faced by mineral concentrators. As a result, concentrat...

(This article belongs to the Special Issue Water within Minerals Processing)
  • Article
  • Open Access
1,586 Views
21 Pages

Optimizing Hydrophobicity of Cu@Zn Foam Catalysts for Efficient CO2 Electroreduction in a Microchannel Reactor

  • Qing Hu,
  • Zhihang Wei,
  • Linjie Chao,
  • Yujing Liu and ,
  • Lin Luo,
  • Bo Zhang and
  • Zhenmin Cheng
  • + 2 authors+ 0 author

9 May 2025

CO2 electrochemical reduction is a promising way to convert CO2 to valuable fuels and chemicals. This study presents a porous Cu@Zn foam catalyst with a tailored hydrophobic surface for enhanced CO2 reduction. The catalyst is synthesized via a modifi...

(This article belongs to the Section Chemical Processes and Systems)
  • Article
  • Open Access
1 Citations
1,513 Views
13 Pages

Investigations into Effects of Inclined Channels on the Forced Foam Drainage

  • Yumeng Deng,
  • Miao Jin,
  • Lisha Dong,
  • Jiakun Tan and
  • Chao Ni

Gangue particle entrainment during flotation remains a significant challenge in mineral processing. Previous studies have shown that incorporating inclined plates into the froth zone can reduce the recovery of fine gangue particles. However, the effe...

(This article belongs to the Section Separation Engineering)
  • Article
  • Open Access
20 Citations
6,371 Views
15 Pages

7 February 2019

The sensitivity enhancement of piezocomposites can realize new applications. Introducing a cellular structure into these materials decreases the permittivity and thus increases their sensitivity. However, foaming of piezocomposites is challenging bec...

(This article belongs to the Special Issue Polymeric Foams)
  • Article
  • Open Access
3 Citations
2,665 Views
19 Pages

Heat Transfer Performance of Gel Foam Layer with Nanoparticles Doping under a Radiative Heat Flux

  • Rifeng Zhou,
  • Pengyu Cui,
  • Qingli Cheng,
  • Xuqing Lang and ,
  • Yong Zhang,
  • Qie Sun and
  • Mu Du
  • + 2 authors+ 0 author

14 December 2022

The risk of fire in the chemical industry’s production process is fatal. Gel foam has been widely employed in petroleum storage tanks, oil pools, and other petrochemical equipment for fire extinguishing and thermal protection. Recently, nanopar...

(This article belongs to the Special Issue Heat and Mass Transfer Enhancement in Microchannels)
  • Article
  • Open Access
2 Citations
2,832 Views
16 Pages

25 April 2024

We present a surface modification technique that turns CuNi foam films with a high contact angle and non-sticking property into a sticky surface. By decorating with mesh-like biaxially oriented polypropylene (BOPP) and adjusting the surface parameter...

(This article belongs to the Special Issue The Microstructures and Advanced Functional Properties of Thin Films)
  • Article
  • Open Access
6 Citations
4,355 Views
21 Pages

19 April 2022

The multiphase splash phenomenon is especially interesting in the context of environmental protection, as it could be a mechanism for transporting various types of pollution. A numerical 3D multiphase transport model was applied to a splash that occu...

(This article belongs to the Section Environmental Sensing)
  • Article
  • Open Access
3 Citations
1,414 Views
23 Pages

The Influence of Selected Parameters of the Mathematical Model on the Simulation Performance of a Municipal Waste-to-Energy Plant Absorber

  • Michał Jurczyk,
  • Marian Banaś,
  • Tadeusz Pająk,
  • Krzysztof Dziedzic and ,
  • Bogusława Łapczyńska-Kordon and
  • Marcin Jewiarz
  • + 1 author+ 0 author

18 December 2024

The primary research aim of this manuscript was to present a simplified absorber model and analyse the simulation results of the absorber model created to which, by design, only water was added and the outlet flue gas temperature was optimal. The obt...

(This article belongs to the Collection Energy Efficiency and Environmental Issues)
  • Article
  • Open Access
12 Citations
3,664 Views
24 Pages

Numerical Modeling of Water Jet Plunging in Molten Heavy Metal Pool

  • Sergey E. Yakush,
  • Nikita S. Sivakov,
  • Oleg I. Melikhov and
  • Vladimir I. Melikhov

20 December 2023

The hydrodynamic and thermal interaction of water with the high-temperature melt of a heavy metal was studied via the Volume-of-Fluid (VOF) method formulated for three immiscible phases (liquid melt, water, and water vapor), with account for phase ch...

(This article belongs to the Special Issue Numerical Simulations and Mathematical Modelling in Engineering Physics)
  • Article
  • Open Access
1 Citations
2,607 Views
17 Pages

An Experimental Analysis of Gas Reduction in Multiphase Flow with a KMS Helical Static Mixer

  • Jose Alejandro Vasquez-Santacruz,
  • Rogelio de Jesus Portillo-Velez,
  • Pedro Javier Garcia-Ramirez,
  • Luis Felipe Marín-Urías and ,
  • Diego Sánchez-Montero and
  • Luis Hector Porrágas-Beltrán
  • + 1 author+ 0 author

10 August 2022

The separation dynamics of a multiphase fluid mixture is studied with the aim to validate the gas reduction from the mixture by means of a KMS helical static mixer device through a laboratory prototype based on the jet-pump artificial lift system for...

(This article belongs to the Special Issue Multiphase and Granular Flows)
  • Article
  • Open Access
9 Citations
2,870 Views
17 Pages

6 February 2023

Foam metal/epoxy interpenetrating phase composite is a new type of composite material with interpenetrating continuity in composition, which exhibits different intrinsic relationships under different stress states in tension and compression, and it i...

(This article belongs to the Special Issue Multiscale Modeling and Simulation of Polymer-Based Composites)
  • Article
  • Open Access
6 Citations
6,172 Views
11 Pages

Study on Combined Vacuum–Mechanical Defoaming Technology for Flotation Froth and Its Mechanism

  • Haibing Jiang,
  • Jiufen Liu,
  • Huaifa Wang,
  • Runquan Yang and ,
  • Wenzhi Zhao,
  • Duo Yang,
  • Song Yin and
  • Liang Shen
  • + 3 authors+ 0 author

14 June 2022

Foam is essential in the flotation process. However, the gas–liquid–solid three-phase froth produced in the flotation process has very strong stability and is difficult to burst spontaneously. The existence of these froths will reduce the...

(This article belongs to the Section Separation Processes)
  • Article
  • Open Access
14 Citations
5,066 Views
26 Pages

23 April 2021

This paper describes experimental investigations of single-phase and two-phase gas–liquid flow through channels with a diameter of 20 mm and length of 2690 mm, filled with metal foams. Three types of aluminium foams with pore densities of 20, 30 and...

(This article belongs to the Special Issue Multiphase Flows)
  • Article
  • Open Access
12 Citations
2,739 Views
17 Pages

30 October 2024

The combination of proteins with polysaccharides and polyphenols is expected to improve their physicochemical and functional properties. In this study, a novel plant-based antioxidant emulsifier was formed by soybean protein isolate (SPI), inulin (IN...

(This article belongs to the Section Food Physics and (Bio)Chemistry)
  • Article
  • Open Access
1 Citations
450 Views
15 Pages

Study on the Effect of Surface Air Leakage on Coal Spontaneous Combustion in Shallow-Buried Composite Goafs: A Case Study of Huojitu Coal Mine

  • Delei Kong,
  • Dong Ma,
  • Yongning Yu,
  • Yixuan Yang and ,
  • Fucheng Zhang and
  • Huogen Luo
  • + 1 author+ 0 author

5 August 2026

Coal spontaneous combustion is a severe hazard in the goafs of shallow-buried coal seams, particularly under the condition of continuous surface air leakage. This study conducted an integrated experimental and 3D multi-field coupled numerical investi...

(This article belongs to the Special Issue Fire/Explosion Risk Assessment and Loss Prevention of Hazardous Materials, Mines and Natural Gas, 2nd Edition)
  • Article
  • Open Access
26 Citations
6,796 Views
15 Pages

17 November 2019

Unfilled and talc-filled Copolymer Polypropylene (PP) samples were produced through low-pressure foam-injection molding (FIM). The foaming stage of the process has been facilitated through a chemical blowing agent (C6H7NaO7 and CaCO3 mixture), a phys...

(This article belongs to the Special Issue Polymeric Foams II)
  • Article
  • Open Access
10 Citations
4,578 Views
13 Pages

Stably Improving the Catalytic Activity of Oxygen Evolution Reactions via Two-Dimensional Graphene Oxide-Incorporated NiFe-Layered Double Hydroxides

  • Ling Chen,
  • Yue Lu,
  • Manman Duanmu,
  • Xin Zhao and ,
  • Shenglu Song,
  • Liyue Duan,
  • Zhipeng Ma,
  • Ailing Song and
  • Guangjie Shao
  • + 4 authors+ 0 author

19 April 2024

NiFe-layered double hydroxides (NiFe-LDH) have been reported to possess exceptional oxygen evolution reaction (OER) activity. However, maintaining the stability of high activity over a long time remains a critical challenge that needs to be addressed...

(This article belongs to the Section Catalytic Materials)
  • Article
  • Open Access
8 Citations
2,986 Views
18 Pages

9 December 2020

Magnesium-based composites reinforced with open-celled carbon foams (Cof) of porosity approx. 97 vol % and three cell sizes (20, 45 and 100 ppi) were examined to characterize the influence of foam cell size on the microstructure and properties when p...

(This article belongs to the Special Issue Lightweight Structural Materials for Automotive and Aerospace)
  • Article
  • Open Access
1 Citations
1,172 Views
30 Pages

Lightweight polylactic acid (PLA LW) is a thermally activated foaming filament in which print temperature governs the extent of in situ gas expansion. This dual role, as a microstructural design parameter and a primary source of performance variabili...

(This article belongs to the Section Composites Modelling and Characterization)
  • Article
  • Open Access
8 Citations
3,841 Views
23 Pages

New Insights on Expandability of Pre-Cured Epoxy Using a Solid-State CO2-Foaming Technique

  • Uy Lan Ngoc Du,
  • Christian Bethke,
  • Volker Altstädt and
  • Holger Ruckdäschel

24 July 2021

Foaming an epoxy is challenging because the process involves the curing reaction of epoxy and hardener (from monomer to oligomer, to a gel and a final three-dimensional crosslinked network) and the loading of gas phase into the epoxy phase to develop...

(This article belongs to the Special Issue Rheology as a Tool for the Investigation of Structures of Polymeric Materials)
  • Article
  • Open Access
31 Citations
7,236 Views
16 Pages

7 March 2019

The thermal and structural performance of geopolymer-coated polyurethane foam–phase change material capsules/geopolymer concrete composites was investigated. Three groups of concrete composites were prepared. The first was pure geopolymer (GP,...

(This article belongs to the Section Construction and Building Materials)
  • Article
  • Open Access
9 Citations
2,262 Views
24 Pages

Energy-Efficient Geopolymer Composites Containing Phase-Change Materials—Comparison of Different Contents and Types

  • Agnieszka Przybek,
  • Michał Łach,
  • Rafał Bogucki,
  • Justyna Ciemnicka and ,
  • Karol Prałat,
  • Artur Koper,
  • Kinga Korniejenko and
  • Adam Masłoń
  • + 3 authors+ 0 author

25 September 2024

The purpose of this study was to analyze the effects of phase-change components on the properties of geopolymer foams. Geopolymer foams are lightweight foamed geopolymers that are characterized by a high degree of porosity. Phase change materials, on...

(This article belongs to the Special Issue Environmentally Friendly Composites Incorporating Waste Materials)
  • Article
  • Open Access
25 Citations
3,661 Views
13 Pages

24 June 2021

The damage process and failure mechanisms were analyzed by a series of quasi-static compressive experiments of seven materials including pure epoxy (EP), three different PPI (pores per linear inch) foam nickel-iron, and three different PPI foam nicke...

  • Article
  • Open Access
30 Citations
3,808 Views
13 Pages

4 March 2021

A smart possible way to cool electronics equipment is represented by passive methods, which do not require an additional power input, such as Phase Change Materials (PCMs). PCMs have the benefit of their latent heat being exploited during the phase c...

(This article belongs to the Special Issue Research on Flow and Heat Transfer in Metal Foams)
  • Article
  • Open Access
5 Citations
4,026 Views
22 Pages

5 May 2021

This paper reports the results of a study concerned with air–water and air–oil two-phase flow in channels packed with open-cell metal foams. The research was conducted in horizontal channel with an internal diameter of 0.02 m and length of 2.61 m. Th...

(This article belongs to the Special Issue Multiphase Flows)
  • Article
  • Open Access
30 Citations
6,823 Views
25 Pages

Evaluation of Slag Foaming Behavior Using Renewable Carbon Sources in Electric Arc Furnace-Based Steel Production

  • Lina Kieush,
  • Johannes Schenk,
  • Andrii Koveria,
  • Andrii Hrubiak and ,
  • Horst Hopfinger and
  • Heng Zheng
  • + 1 author+ 0 author

12 June 2023

The influence of different carbon sources, including anthracite, calcined petroleum coke, three samples of high-temperature coke, biochar, and a mixture of 50 wt.% biochar and 50 wt.% coke, on slag foaming behavior was studied. The slag’s compo...

(This article belongs to the Special Issue Recent Progress in Biomass Pyrolysis and High Value Utilization of Pyrolytic Carbon)
  • Article
  • Open Access
23 Citations
7,160 Views
18 Pages

11 February 2019

To improve the foaming behavior of a common linear polypropylene (PP) resin, polycarbonate (PC) was blended with PP, and three different grafted polymers were used as the compatibilizers. The solid and foamed samples of the PP/PC 3:1 blend with diffe...

(This article belongs to the Special Issue Foaming and Injection Moulding in Polymer Processing)
  • Article
  • Open Access
6 Citations
3,103 Views
20 Pages

9 February 2022

This article presents the dynamic process of the three-phase contact (TPC) formation by colliding bubbles onto muscovite and talc surfaces in water and two types of solutions including cationic CTAC surfactant (cetyltrimethyl ammoniumchloride) and an...

(This article belongs to the Section Mineral Processing and Extractive Metallurgy)
  • Article
  • Open Access
14 Citations
4,476 Views
21 Pages

18 October 2022

In this paper, the effects of three cations, Ca2+, Mg2+, and Na+, on the stability of APG foams were investigated experimentally. The results show that cations can slow down the process of liquid drainage and coarsening of APG foam, which is benefici...

(This article belongs to the Special Issue Technological Innovation, Economic Analysis, and Environment Impact for Energy Production and Utilization)
  • Article
  • Open Access
34 Citations
5,008 Views
27 Pages

21 November 2022

Thermal management of electronic components is critical for long-term reliability and continuous operation, as the over-heating of electronic equipment leads to decrement in performance. The novelty of the current experimental study is to investigate...

(This article belongs to the Section D1: Advanced Energy Materials)
  • Article
  • Open Access
13 Citations
2,894 Views
22 Pages

28 January 2021

A local thermal non-equilibrium analysis of heat and fluid flow in a channel fully filled with aluminum foam is performed for three cases: (a) pore density of 5 PPI (pore per inch), (b) pore density of 40 PPI, and (c) two different layers of 5 and 40...

(This article belongs to the Section J: Thermal Management)
  • Article
  • Open Access
18 Citations
3,246 Views
29 Pages

31 August 2023

This paper investigates the influence of biochar, either as an individual component or in combination with high-temperature coke, on the slag foaming behavior. High-temperature coke serves as a reference. Three scenarios were considered to study the...

(This article belongs to the Special Issue Recent Progress in Biomass Pyrolysis and High Value Utilization of Pyrolytic Carbon)
  • Article
  • Open Access
21 Citations
2,625 Views
16 Pages

Influence of Different Types of Surfactants on the Flotation of Natural Quartz by Dodecylamine

  • Yuxin Ao,
  • Cong Han,
  • Linghao Kong,
  • Yanbai Shen and ,
  • Sikai Zhao,
  • Wengang Liu and
  • Shijie Zhou
  • + 2 authors+ 0 author

The synergistic effect among flotation agents is why combined flotation agents exhibit superior performance compared to single flotation agents. This research investigates the influence of three surfactants with different charges of polar groups, sod...

(This article belongs to the Section Cross-Field Chemistry)
  • Article
  • Open Access
2 Citations
1,654 Views
17 Pages

13 March 2025

In this study, the mechanical behavior of AA6082 foams with Weaire–Phelan (WP) cell structures under compressive loading was analyzed. The foams were produced using the lost-PLA replication method, a cost-effective and straightforward manufactu...

(This article belongs to the Special Issue Recent Advances in the Mechanical Properties and Microstructural Features of Porous Materials)
  • Article
  • Open Access
10 Citations
3,307 Views
20 Pages

17 August 2021

Heat transfer under flow boiling is better in a rectangular channel filled with open-cell metal foam than in an empty channel, but the high pressure drop is a drawback of the empty channel method. In this study, various types of metal foam insert con...

(This article belongs to the Special Issue Research on Flow and Heat Transfer in Metal Foams)
  • Proceeding Paper
  • Open Access
2 Citations
1,715 Views
4 Pages

Sandwich structures are widely used in aeronautics both for primary and secondary structures such as landing gear doors, flaps or floors. Multi-cores materials sandwich structures presents many advantages. By adding layers with another materials that...

(This article belongs to the Proceedings of Innovation Aviation & Aerospace Industry - International Conference 2020)
  • Article
  • Open Access
7 Citations
2,767 Views
23 Pages

Syntactic Iron Foams’ Properties Tailored by Means of Case Hardening via Carburizing or Carbonitriding

  • Jörg Weise,
  • Dirk Lehmhus,
  • Jaqueline Sandfuchs,
  • Matthias Steinbacher and ,
  • Rainer Fechte-Heinen and
  • Matthias Busse
  • + 1 author+ 0 author

4 August 2021

Metal foam inserts are known for their high potential for weight and vibration reduction in composite gear wheels. However, most metal foams do not meet the strength requirements mandatory for the transfer of sufficiently high levels of torque by the...

(This article belongs to the Section Metals and Alloys)
  • Article
  • Open Access
14 Citations
4,517 Views
21 Pages

Thermo-Mechanical Behavior of Novel EPDM Foams Containing a Phase Change Material for Thermal Energy Storage Applications

  • Marica Bianchi,
  • Francesco Valentini,
  • Giulia Fredi,
  • Andrea Dorigato and
  • Alessandro Pegoretti

27 September 2022

In this paper Ethylene Propylene Diene Monomer rubber (EPDM) foams were filled with different amounts of paraffin, a common phase change material (PCM) having a melting temperature at about 70 °C, to develop novel rubber foams with thermal energy...

(This article belongs to the Special Issue Polymer Research in INSTM—National Interuniversity Consortium of Materials Science and Technology—Never Stops)
  • Article
  • Open Access
13 Citations
2,536 Views
14 Pages

22 July 2020

This paper reports the results of a study concerned with air−water and air−oil two–phase flow pattern analysis in the channels with open–cell metal foams. The research was conducted in a horizontal channel with an internal dia...

(This article belongs to the Special Issue Advanced and High Performance Metallic Foams)
  • Technical Note
  • Open Access
1 Citations
2,086 Views
12 Pages

Investigation of Air Foam and Heptafluoropropane Foam Fire Extinguishment for Storage Tanks Containing Low-Boiling-Point Flammable Liquids

  • Youquan Bao,
  • Lu Wang,
  • Huiqiang Zhi,
  • Shichang Lu and ,
  • Junyang Wang,
  • Xia Du,
  • Yiliang Huang,
  • Kanghui Xu,
  • Qiyang Shu and
  • Xiaopo Wang
  • + 5 authors+ 0 author

10 April 2025

Due to the high saturated vapor pressure of low-boiling-point flammable liquids, it is difficult to make fire extinguishers for storage tanks containing them. Air foam extinguishing technology has been recommended by several standards. However, the e...

(This article belongs to the Special Issue Fire Extinguishing Agent and Application)
  • Article
  • Open Access
16 Citations
3,239 Views
16 Pages

Thermo-Economic Assessments on a Heat Storage Tank Filled with Graded Metal Foam

  • Gang Liu,
  • Yuanji Li,
  • Pan Wei,
  • Tian Xiao and ,
  • Xiangzhao Meng and
  • Xiaohu Yang
  • + 1 author+ 0 author

30 September 2022

To save and better deploy waste heat, the use of a mobilized heat storage system (MHSS) with phase change enhancement means is developed. In this paper, three kinds of gradient structures (positive gradient, negative gradient, and non-gradient) are d...

(This article belongs to the Topic Thermal Energy Transfer and Storage)
  • Article
  • Open Access
10 Citations
3,954 Views
15 Pages

16 November 2022

In this study, an asymmetric supercapacitor (ASSC) device is assembled by the deposition and annealing of silver-doped mixed metal oxides on reduced graphene oxide (rGO)/Ni foam and activated carbon (AC) on Ni foam as positive and negative electrodes...

(This article belongs to the Topic Batteries, Supercapacitors, Fuel Cells and Combined Energy/Power Supply Systems)

of 4