Skip to Content

171 Results Found

  • Feature Paper
  • Article
  • Open Access
22 Citations
6,712 Views
23 Pages

Development and Validation of 3D-CFD Injection and Combustion Models for Dual Fuel Combustion in Diesel Ignited Large Gas Engines

  • Lucas Eder,
  • Marko Ban,
  • Gerhard Pirker,
  • Milan Vujanovic and ,
  • Peter Priesching and
  • Andreas Wimmer
  • + 1 author+ 0 author

14 March 2018

This paper focuses on improving the 3D-Computational Fluid Dynamics (CFD) modeling of diesel ignited gas engines, with an emphasis on injection and combustion modeling. The challenges of modeling are stated and possible solutions are provided. A spec...

(This article belongs to the Special Issue Selected Papers from SDEWES 2017: The 12th Conference on Sustainable Development of Energy, Water and Environment Systems)
  • Article
  • Open Access
19 Citations
9,489 Views
20 Pages

A Three-Zone Scavenging Model for Large Two-Stroke Uniflow Marine Engines Using Results from CFD Scavenging Simulations

  • Michael I. Foteinos,
  • Alexandros Papazoglou,
  • Nikolaos P. Kyrtatos,
  • Anastassios Stamatelos and ,
  • Olympia Zogou and
  • Antiopi-Malvina Stamatellou
  • + 1 author+ 0 author

7 May 2019

The introduction of modern aftertreatment systems in marine diesel engines call for accurate prediction of exhaust gas temperature, since it significantly affects the performance of the aftertreatment system. The scavenging process establishes the in...

(This article belongs to the Section J: Thermal Management)
  • Feature Paper
  • Article
  • Open Access
11 Citations
4,086 Views
19 Pages

Modeling of Hydrogen Combustion from a 0D/1D Analysis to Complete 3D-CFD Engine Simulations

  • Thomas Gal,
  • Robin Schmelcher,
  • Antonino Vacca,
  • Francesco Cupo and ,
  • Marco Chiodi and
  • André Casal Kulzer
  • + 1 author+ 0 author

6 November 2024

Hydrogen and its unique properties pose major challenges to the development of innovative combustion engines, while it represents a viable alternative when it is based on renewable energy sources. The present paper deals with the holistic approach of...

(This article belongs to the Special Issue Towards Climate Neutral Thermochemical Energy Conversion)
  • Article
  • Open Access
26 Citations
4,344 Views
19 Pages

19 August 2020

Reynolds-averaged Navier–Stokes (RANS) three-dimensional (3D) computational fluid dynamics (CFD) simulations of gaseous emissions from combustion engines are very demanding due to the complex geometry, the emissions formation mechanisms, and th...

(This article belongs to the Special Issue Advances in Spark-Ignition Engines)
  • Article
  • Open Access
2 Citations
2,667 Views
33 Pages

29 September 2025

In the pursuit of zero-emission mobility, hydrogen represents a promising fuel for internal combustion engines. However, its low volumetric energy density poses challenges, especially for high-performance applications where compactness and lightweigh...

(This article belongs to the Special Issue Internal Combustion Engines: Research and Applications—3rd Edition)
  • Article
  • Open Access
11 Citations
3,006 Views
26 Pages

Virtual Development of a Single-Cylinder Hydrogen Opposed Piston Engine

  • Enrico Mattarelli,
  • Stefano Caprioli,
  • Tommaso Savioli,
  • Antonello Volza and ,
  • Claudiu Marcu Di Gaetano Iftene and
  • Carlo Alberto Rinaldini
  • + 1 author+ 0 author

22 October 2024

A significant challenge in utilizing hydrogen in conventional internal combustion engines is achieving a balance between NOx emissions and brake power output. A lean premixed charge (Lambda ≈ 2.5) allows for efficient and stable combustion with...

(This article belongs to the Special Issue Renewable Fuels for Internal Combustion Engines: 2nd Edition)
  • Article
  • Open Access
14 Citations
7,060 Views
24 Pages

An AI-Based Fast Design Method for New Centrifugal Compressor Families

  • Marco Bicchi,
  • Davide Biliotti,
  • Michele Marconcini,
  • Lorenzo Toni and ,
  • Francesco Cangioli and
  • Andrea Arnone
  • + 1 author+ 0 author

Limiting global warming’s effects requires a sudden reduction of greenhouse gas emissions to pursue a net-zero carbon growth in the next decades. Along with this energy transition, drastic and rapid changes in demand are expected in many sector...

(This article belongs to the Section Turbomachinery)
  • Article
  • Open Access
3 Citations
1,662 Views
30 Pages

Prediction of Combustion Parameters and Pollutant Emissions of a Dual-Fuel Engine Based on Recurrent Neural Networks

  • Joel Freidy Ebolembang,
  • Fabrice Parfait Nang Nkol,
  • Lionel Merveil Anague Tabejieu,
  • Fernand Toukap Nono and
  • Claude Valery Ngayihi Abbe

9 September 2025

A critical challenge in engine research lies in minimizing harmful emissions while optimizing the efficiency of internal combustion engines. Dual-fuel engines, operating with methanol and diesel, offer a promising alternative, but their combustion mo...

(This article belongs to the Section Energy Science and Technology)
  • Article
  • Open Access
24 Citations
7,406 Views
21 Pages

Development and Assessment of an Integrated 1D-3D CFD Codes Coupling Methodology for Diesel Engine Combustion Simulation and Optimization

  • Federico Millo,
  • Andrea Piano,
  • Benedetta Peiretti Paradisi,
  • Mario Rocco Marzano and ,
  • Andrea Bianco and
  • Francesco C. Pesce
  • + 1 author+ 0 author

1 April 2020

In this paper, an integrated and automated methodology for the coupling between 1D- and 3D-CFD simulation codes is presented, which has been developed to support the design and calibration of new diesel engines. The aim of the proposed methodology is...

(This article belongs to the Special Issue Internal Combustion Engines Improving Performance, Fuel Economy and Emissions)
  • Feature Paper
  • Review
  • Open Access
13 Citations
6,922 Views
39 Pages

20 September 2024

The growing demand to reduce emissions of pollutants and CO2 from internal combustion engines has led to a critical need for the development of ultra-lean burn engines that can maintain combustion stability while mitigating the risk of knock. One of...

(This article belongs to the Special Issue New Fuels and Advanced Combustion Modes for Innovative Internal Combustion Engines)
  • Article
  • Open Access
3 Citations
1,868 Views
22 Pages

7 February 2025

This study performed a 3D CFD analysis on a GP3 rotary engine to determine the stroke and flow characteristics and examine the thermal- and flow-related design factors’ validity. The 3D CFD analysis was performed using the CONVERGE program, uti...

(This article belongs to the Special Issue Advances in Powertrain Design for Greener and Sustainable Non-road Mobile Machineries)
  • Article
  • Open Access
3 Citations
6,014 Views
16 Pages

12 December 2023

A Kelvin-Helmholtz instability is formed when two fluids of different densities exert a shear on one another at their interface when flowing in opposite directions. This paper presents a step-by-step guide for the design of a low-cost, small-scale, e...

  • Article
  • Open Access
52 Citations
19,095 Views
19 Pages

Optimization methods have been widely applied to the aerodynamic design of gas turbine blades. While applying optimization to high-fidelity computational fluid dynamics (CFD) simulations has proven capable of improving engineering design performance,...

  • Article
  • Open Access
30 Citations
8,814 Views
22 Pages

Automated Simulation Framework for Urban Wind Environments Based on Aerial Point Clouds and Deep Learning

  • Chujin Sun,
  • Fan Zhang,
  • Pengju Zhao,
  • Xinyi Zhao and ,
  • Yuli Huang and
  • Xinzheng Lu
  • + 1 author+ 0 author

18 June 2021

Computational fluid dynamics (CFD) simulation is a core component of wind engineering assessment for urban planning and architecture. CFD simulations require clean and low-complexity models. Existing modeling methods rely on static data from geograph...

(This article belongs to the Special Issue Applications of AI and Remote Sensing in Urban Systems)
  • Article
  • Open Access
4 Citations
3,625 Views
21 Pages

23 September 2024

The objective of this study is to develop a 1D CFD simulation model to identify the optimal design parameters, using GT-POWER prior to the optimization of a new rotary engine derived from a three-lobe gerotor pump (GP3 RTE) based on 3D CFD simulation...

(This article belongs to the Special Issue Advances in Powertrain Design for Greener and Sustainable Non-road Mobile Machineries)
  • Article
  • Open Access
7 Citations
4,400 Views
20 Pages

In-Cylinder Heat Transfer Model Proposal Compatible with 1D Simulations in Uniflow Scavenged Engines

  • Héctor Climent,
  • Andrés Tiseira,
  • Josep Gomez-Soriano and
  • Aditya Darbhamalla

21 March 2023

Advanced two-stroke engines are considered as powertrains for range extenders in hybrid electric vehicles due to size, simplicity, cost, and power density advantages. In-cylinder heat transfer is a phenomenon that affects the temperature of burnt gas...

(This article belongs to the Section Energy Science and Technology)
  • Article
  • Open Access
8 Citations
3,288 Views
22 Pages

Tabulated Chemistry Combustion Model for Cost-Effective Numerical Simulation of Dual-Fuel Combustion Process

  • Marija Stipic,
  • Branislav Basara,
  • Steffen J. Schmidt and
  • Nikolaus A. Adams

13 December 2023

This study is dedicated to improving the efficiency of the flamelet-generated manifold (FGM) tabulated chemistry combustion modeling approach for predicting the combustion process in diesel-ignited internal combustion (IC) engines. The primary focus...

(This article belongs to the Topic Computational Fluid Dynamics (CFD) and Its Applications)
  • Article
  • Open Access
2 Citations
3,095 Views
23 Pages

25 June 2022

This paper describes the simulative approach to calibrate an already extremely highly turbocharged industrial diesel engine for higher low-speed torque. The engine, which is already operating at its cylinder-pressure maximum, is to achieve close to 3...

(This article belongs to the Section E: Electric Vehicles)
  • Article
  • Open Access
3 Citations
3,133 Views
33 Pages

20 March 2025

For computational fluid dynamic (CFD) modeling of advanced combustion engines, the cylinder is usually considered a closed system in which the initial conditions are estimated based on the experimental data. Most of these approximations hinder observ...

(This article belongs to the Special Issue Combustion Process, Emission Control, and Energy Generation in Internal Combustion Engines)
  • Feature Paper
  • Article
  • Open Access
6 Citations
5,361 Views
13 Pages

Computational Methodology for Knocking Combustion Analysis in Compression-Ignited Advanced Concepts

  • José Ramón Serrano,
  • Ricardo Novella,
  • Josep Gomez-Soriano and
  • Pablo José Martinez-Hernandiz

20 September 2018

In the present work, a numerical methodology based on three-dimensional (3D) computational fluid dynamics (CFD) was developed to predict knock in a 2-Stroke engine operating with gasoline Partially Premixed Combustion (PPC) concept. Single-cycle Unst...

(This article belongs to the Special Issue Direct Injection Reciprocating Internal Combustion Engines)
  • Article
  • Open Access
32 Citations
6,667 Views
19 Pages

2D CFD Simulation of Water Injection Strategies in a Large Marine Engine

  • Tomislav Senčić,
  • Vedran Mrzljak,
  • Paolo Blecich and
  • Igor Bonefačić

A two-dimensional computational fluid dynamics (2D CFD) simulation of a low-speed two-stroke marine engine simulation was performed in order to investigate the performance of 2D meshes that allow the use of more complex chemical schemes and pollutant...

  • Article
  • Open Access
15 Citations
8,404 Views
16 Pages

3D Hydrodynamic Modelling Enhances the Design of Tendaho Dam Spillway, Ethiopia

  • Getnet Kebede Demeke,
  • Dereje Hailu Asfaw and
  • Yilma Seleshi Shiferaw

4 January 2019

Hydraulic structures are often complex and in many cases their designs require attention so that the flow behavior around hydraulic structures and their influence on the environment can be predicted accurately. Currently, more efficient computational...

(This article belongs to the Section Hydraulics and Hydrodynamics)
  • Article
  • Open Access
5 Citations
4,288 Views
20 Pages

2-Stroke RCCI Engines for Passenger Cars

  • Enrico Mattarelli,
  • Carlo Alberto Rinaldini,
  • Luca Marmorini,
  • Stefano Caprioli and ,
  • Francesco Legrottaglie and
  • Francesco Scrignoli
  • + 1 author+ 0 author

5 February 2022

Reactivity Controlled Compression Ignition (RCCI) is one of the most promising solutions among the low temperature combustion concepts, in terms of thermal efficiency and pollutant emissions. However, for values of brake mean effective pressure highe...

(This article belongs to the Special Issue Numerical Simulation for Next Generation Engines)
  • Article
  • Open Access
1 Citations
1,112 Views
17 Pages

Numerical Investigation of Jatropha and Castor Biofuel Droplet Evaporation at High Engine Operating Conditions

  • Ali Raza,
  • Marva Hadia,
  • Zunaira Tu Zehra,
  • Sajjad Miran and ,
  • Muhammad Khurram and
  • Ghulam Murtaza
  • + 1 author+ 0 author

14 April 2026

Fossil fuel depletion has increased interest in renewable alternatives such as biodiesel derived from non-edible plant oils. Droplet evaporation is a key process influencing fuel–air mixing and combustion efficiency in diesel engines. In this s...

  • Feature Paper
  • Article
  • Open Access
22 Citations
7,455 Views
21 Pages

Optimization of Pre-Chamber Geometry and Operating Parameters in a Turbulent Jet Ignition Engine

  • Viktor Dilber,
  • Momir Sjerić,
  • Rudolf Tomić,
  • Josip Krajnović and ,
  • Sara Ugrinić and
  • Darko Kozarac
  • + 1 author+ 0 author

28 June 2022

A turbulent jet ignition engine enables operation with lean mixtures, decreasing nitrogen oxide (NOX) emissions up to 92%, while the engine efficiency can be increased compared to conventional spark-ignition engines. The geometry of the pre-chamber a...

(This article belongs to the Section I2: Energy and Combustion Science)
  • Review
  • Open Access
12 Citations
4,830 Views
42 Pages

18 September 2025

Accurate wind field modeling over hilly terrain is critical for wind energy, infrastructure safety, and environmental assessment, yet its inherent complexity poses significant simulation challenges. This paper systematically reviews this field’...

  • Article
  • Open Access
14 Citations
4,066 Views
22 Pages

4 January 2021

Gas turbine engines are highly intricate machines, and every component of them is closely associated with one another. In the traditional engine developing process, vast experiment tests are needed. To reduce unnecessary trials, a whole gas turbine e...

(This article belongs to the Section Aerospace Science and Engineering)
  • Article
  • Open Access
5 Citations
3,392 Views
20 Pages

Effect of Engineered Roughness on the Performance of Journal Bearings Lubricated by Bingham Plastic Fluid Using Computational Fluid Dynamics (CFD)

  • Nur Cahyo,
  • P. Paryanto,
  • Ariyana Dwiputra Nugraha,
  • Arionmaro Simaremare and ,
  • Indra Ardhanayudha Aditya,
  • Bara Songka Laktona Siregar and
  • Mohammad Tauviqirrahman
  • + 2 authors+ 0 author

25 November 2022

A journal bearing is a machine element that is used to keep the shaft rotating about its axis. The increasing demand for journal bearing applications in high-speed machines that are efficient and economical has resulted in the need for improvements t...

(This article belongs to the Special Issue Tribology in Manufacturing and Design)
  • Feature Paper
  • Article
  • Open Access
12 Citations
7,000 Views
20 Pages

26 March 2024

Hydrogen-powered mobility is believed to be crucial in the future, as hydrogen constitutes a promising solution to make up for the non-programmable character of the renewable energy sources. In this context, the hydrogen-fueled internal combustion en...

(This article belongs to the Special Issue Disruptive Solutions for Innovative Internal Combustion Engines and Advanced Combustion)
  • Article
  • Open Access
1,155 Views
22 Pages

Research on Quasi-One-Dimensional Ejector Model

  • Jinfan Chen,
  • Kaifeng He,
  • Jianqiang Zhang and
  • Guoliang Wang

29 September 2025

A new quasi-one-dimensional ejector model for the prediction of ejector performance is carried out, which is based on the theory of ideal gas expansion and free layer development. The model is proposed for calculation of the variable area bypass inje...

(This article belongs to the Special Issue High Speed Aircraft and Engine Design)
  • Article
  • Open Access
3 Citations
2,475 Views
20 Pages

Film Cooling Modeling in a Turbine Working under the Unsteady Exhaust Flow of Pulsed Detonation Combustion

  • Gokkul Raj Varatharajulu Purgunan,
  • Majid Asli,
  • Teodosio Nacci,
  • Daniela Anna Misul and ,
  • Simone Salvadori and
  • Panagiotis Stathopoulos
  • + 1 author+ 0 author

8 March 2024

Pressure gain combustors (PGCs) have demonstrated significant advantages over conventional combustors in gas turbine engines by increasing the thermal efficiency and reducing the pollution emission level. PGCs use shock waves to transfer energy which...

(This article belongs to the Section J: Thermal Management)
  • Article
  • Open Access
31 Citations
10,629 Views
19 Pages

17 June 2015

In-cylinder air flow is very important from the point of view of mixture formation and combustion. In this direction, intake chamber structure and piston crown shape play a very crucial role for in-cylinder air pattern of opposed-piston two-stroke (O...

(This article belongs to the Special Issue Electrical Power and Energy Systems for Transportation Applications)
  • Article
  • Open Access
3 Citations
5,306 Views
22 Pages

Analysis of a Stator-Rotor-Stator Spinning Disk Reactor in Single-Phase and Two-Phase Boiling Conditions Using a Thermo-Fluid Flow Network and CFD

  • Lorenzo Mazzei,
  • Francesco Maria Marin,
  • Cosimo Bianchini,
  • Riccardo Da Soghe and ,
  • Cristina Bertani,
  • Dario Pastrone,
  • Maddalena Angelucci,
  • Giuseppe Caggiano and
  • Michiel de Beer
  • + 4 authors+ 0 author

18 January 2022

Cryogenic liquid propellants are used in liquid rocket engines to obtain high specific impulse. The flow rates are controlled by turbopumps that deliver liquid propellant to the engine at high pressure levels. Due to the very low saturation temperatu...

(This article belongs to the Special Issue Multiphase Flow in Pipes with and without Porous Media)
  • Article
  • Open Access
14 Citations
7,021 Views
17 Pages

29 August 2017

The multiple injection strategy has been widely used in diesel engines to reduce engine noise, NOx and soot formation. Fuel injection developments such as the common-rail and piezo-actuator system provide more precise control of the injection quantit...

  • Feature Paper
  • Article
  • Open Access
8 Citations
4,563 Views
16 Pages

Numerical Study on Sensitivity of Turbofan Engine Performance to Blade Count of Centrifugal Compressor Impeller

  • Arkadiusz Bednarz,
  • Kirill Kabalyk,
  • Robert Jakubowski and
  • Rafał Bartłomowicz

8 July 2023

The aim of this publication was to investigate the effects the blade count of a high-pressure centrifugal compressor’s impeller has on the performance of the DGEN 380 turbine engine at take-off. The study began with the development of a zero-di...

(This article belongs to the Topic Decarbonised Powertrains and Emission Control in Transportation)
  • Article
  • Open Access
8 Citations
6,071 Views
24 Pages

18 May 2019

Turbulence is one of the most important aspects in spark-ignition engines as it can significantly affect burn rates, heat transfer rates, and combustion stability, and thus the performance. Turbulence originates from a large-scale mean motion that oc...

(This article belongs to the Special Issue Internal Combustion Engines Improving Performance, Fuel Economy and Emissions)
  • Article
  • Open Access
9 Citations
6,153 Views
24 Pages

A Comparative Study of Different CFD Codes for Fluidized Beds

  • Parindra Kusriantoko,
  • Per Fredrik Daun and
  • Kristian Etienne Einarsrud

16 June 2024

Fluidized beds are pivotal in the process industry and chemical engineering, with Computational Fluid Dynamics (CFD) playing a crucial role in their design and optimization. Challenges in CFD modeling stem from the scarcity or inconsistency of experi...

(This article belongs to the Topic Nonlinear Phenomena, Chaos, Control and Applications to Engineering and Science and Experimental Aspects of Complex Systems)
  • Article
  • Open Access
2 Citations
1,557 Views
21 Pages

8 October 2025

Finite element analysis (FEA)-based computational fluid dynamics (CFD) simulations are essential in biomedical engineering for studying haemodynamics, yet their high computational cost limits large-scale parametric studies. This paper presents a comp...

(This article belongs to the Special Issue Computational Intelligence and Soft Computing: Recent Applications—Second Volume)
  • Article
  • Open Access
10 Citations
5,576 Views
27 Pages

Retrofitting of Pressurized Sand Traps in Hydropower Plants

  • Wolfgang Richter,
  • Kaspar Vereide,
  • Gašper Mauko,
  • Ola H. Havrevoll and ,
  • Josef Schneider and
  • Gerald Zenz
  • + 1 author+ 0 author

14 September 2021

Unlined pressure tunnels in sound rock, combined with pressurized sand traps at the downstream end, allow for low-cost construction of hydropower tunnel systems. This design concept is utilized in hydropower plants across the world. Currently, many s...

(This article belongs to the Special Issue Advances and Challenges in Hydropower)
  • Article
  • Open Access
25 Citations
8,645 Views
27 Pages

A New Wind Turbine CFD Modeling Method Based on a Porous Disk Approach for Practical Wind Farm Design

  • Takanori Uchida,
  • Yoshihiro Taniyama,
  • Yuki Fukatani,
  • Michiko Nakano and ,
  • Zhiren Bai,
  • Tadasuke Yoshida and
  • Masaki Inui
  • + 2 authors+ 0 author

19 June 2020

In this study, the new computational fluid dynamics (CFD) porous disk (PD) wake model was proposed in order to accurately predict the time-averaged wind speed deficits in the wind turbine wake region formed on the downstream side by the 2-MW wind tur...

(This article belongs to the Section A3: Wind, Wave and Tidal Energy)
  • Article
  • Open Access
9 Citations
1,208 Views
18 Pages

Assessment of the Use of a Passive Pre-Chamber in a Marine Engine Fueled with Ammonia–Hydrogen Mixtures

  • Gabriele D’Antuono,
  • Enzo Galloni,
  • Davide Lanni,
  • Gianpaolo D’Andrea and
  • Gustavo Fontana

28 October 2025

This study investigates the combustion process in a marine spark-ignition engine fueled with an ammonia–hydrogen blend (15% hydrogen by volume) using a passive pre-chamber. A 3D-CFD model, supported by a 1D engine model, was employed to analyze...

(This article belongs to the Section I2: Energy and Combustion Science)
  • Article
  • Open Access
19 Citations
4,662 Views
19 Pages

29 October 2021

In this paper, the effects of different diesel–methanol blends on the combustion and emission characteristics of diesel engines are investigated in terms of cylinder pressure, heat release rate, cylinder temperature, brake specific fuel consumption,...

(This article belongs to the Special Issue Clean Combustion and Emission in Vehicle Power System)
  • Article
  • Open Access
6 Citations
3,429 Views
30 Pages

29 December 2020

Organic Rankine cycle technology is gaining increasing interest as one of potent future waste heat recovery potential from internal combustion engines. The turbine is the component where power production takes place. Therefore, careful attention to t...

(This article belongs to the Special Issue Mathematical Modelling in Applied Sciences)
  • Article
  • Open Access
4 Citations
16,871 Views
58 Pages

25 February 2020

Computational Fluid Dynamics (CFD) models are being rapidly integrated into applications across all sciences and engineering. CFD harnesses the power of computers to solve the equations of fluid dynamics, which otherwise cannot be solved analytically...

(This article belongs to the Special Issue Teaching and Learning of Fluid Mechanics)
  • Perspective
  • Open Access
87 Citations
11,118 Views
13 Pages

Hydrogen Application as a Fuel in Internal Combustion Engines

  • Stefania Falfari,
  • Giulio Cazzoli,
  • Valerio Mariani and
  • Gian Marco Bianchi

8 March 2023

Hydrogen is the energy vector that will lead us toward a more sustainable future. It could be the fuel of both fuel cells and internal combustion engines. Internal combustion engines are today the only motors characterized by high reliability, durati...

(This article belongs to the Section I2: Energy and Combustion Science)
  • Feature Paper
  • Article
  • Open Access
30 Citations
15,751 Views
20 Pages

8 June 2017

Around a third of the energy input in an automotive engine is wasted through the exhaust system. Since numerous technologies to harvest energy from exhaust gases are accessible, it is of great interest to find time- and cost-efficient methods to eval...

(This article belongs to the Special Issue Internal Combustion Engines (ICE) for Ground Transport)
  • Article
  • Open Access
3 Citations
3,120 Views
15 Pages

A 3D Numerical Study of Supersonic Steam Dumping Process of the Pressurizer Relief Tank

  • Yi Wang,
  • Xiao-Wei Guo,
  • Dong Liu,
  • Ge Wu and ,
  • Chao Li,
  • Lijuan Chen,
  • Ran Zhao and
  • Canqun Yang
  • + 3 authors+ 0 author

14 June 2019

Simulating the steam dumping process of a pressurized relief tank is a challenging engineering problem, due to the massive computing resource requirements and its complex physical models. This study gave a comprehensive 3D numerical study for the tra...

  • Article
  • Open Access
5 Citations
4,437 Views
18 Pages

21 November 2020

Geothermal is a renewable energy source that can be untapped through various subsurface technologies. Closed geothermal well solutions, such as deep geothermal heat exchangers (DBHEs), consist of circulating a working fluid to recover the available h...

(This article belongs to the Special Issue Geothermal Resources)
  • Article
  • Open Access
10 Citations
6,703 Views
18 Pages

Simulation Modeling Method and Experimental Investigation on the Uniflow Scavenging System of an Opposed-Piston Folded-Cranktrain Diesel Engine

  • Fukang Ma,
  • Zhenfeng Zhao,
  • Yangang Zhang,
  • Jun Wang and ,
  • Yaonan Feng,
  • Tiexiong Su,
  • Yi Zhang and
  • Yuhang Liu
  • + 3 authors+ 0 author

20 May 2017

The scavenging process for opposed-piston folded-cranktrain (OPFC) diesel engines can be described by the time evolution of the in-cylinder and exhaust chamber residual gas rates. The relation curve of in-cylinder and exhaust chamber residual gas rat...

  • Article
  • Open Access
1,284 Views
24 Pages

Shock-aware aerodynamic shape optimization of transonic airfoils requires surrogate models that capture both integral aerodynamic trends and shock-relevant pressure distribution features. This study addresses drag-oriented optimization of the RAE2822...

(This article belongs to the Special Issue Aerodynamic Optimization of Flight Wing)

of 4