We demonstrate the fabrication of air gaps in a PECVD SiN interlayer through lateral recess by employing two consecutive plasma etch steps on an AlN/SiN/Al2O3 stack. This approach enables the preservation of sub-100 nm openings in Al2O3, offering a p...
The exposure of workers to propylene glycol monomethyl ether acetate (PGMEA) in manufacturing environments can result in potential health risks. Therefore, systems for PGMEA removal are required for indoor air quality control. In this study, core&nda...
The focus of this study is on the manufacturing of micro air bearings (MABs) using silica film assisted processing. Structure of the three-layer micro air bearing is described in detail and the salient process flow of etching and bonding is illustrat...
In laser etching of ITO glass, the warpage due to workpiece positioning causes breakpoint or deformation of micron-scale etching circuits. Based on traditional laser etching, a micro-airflow array pressurization is proposed by using a micro-flow air...
For the development of high efficiency porous supports for composite membrane preparation, polysulfone (PSf) hollow fiber membranes (outer diameter 1.57 mm, inner diameter 1.12 mm) were modified by air plasma using the low temperature plasma treatmen...
Any excess solvent from dental adhesive systems must be eliminated prior to material photopolymerization. For this purpose, numerous approaches have been proposed, including the use of a warm air stream. This study aimed to investigate the effect of...
The aim of this in vitro study was to assess the influence of surface pretreatment on shear bond strength (SBS) of an adhesive resin cement (G-CEM Link Force TM, GC Corporation, Tokyo, Japan) to three different yttria-stabilized tetragonal zirconia p...
Background: Surface treatment of the intaglio surface of zirconia is important for bonding. However, it could affect the strength of the materials. The purpose of this study is to compare the effect of laser, etching, and air abrasion surface treatme...
Background: Bonding to sclerotic dentin remains one of the most challenging procedures in restorative dentistry due to tubular occlusion and hypermineralization, which limit resin infiltration. This study evaluated the influence of adhesive system, s...
This study developed a versatile and facile method for creating pores and tuning the porous structure in the polymer latex films by selectively etching the added functional polyvinyl pyrrolidone (PVP) molecules. The pore formed in the latex films had...
Background/Objectives: To compare the effects of different surface treatments on the color and translucency of three types of zirconia ceramics. Methods: Ninety CAD/CAM-milled zirconia disks (10 mm diameter, 1 mm thickness) were fabricated from Cerco...
Freestanding thin film electrodes are competitive candidate materials for high-performance energy stockpile equipment due to their self-supporting structure and because they lack any polymer binder or conductive additive. In our work, a porous carbon...
Platinum alloy gauzes are employed for the high-temperature oxidation of NH3 to NO used in the industrial production of HNO3 for application in agricultural fertilizers. To enhance the efficiency of NH3 oxidation, various Pt–Pd–Rh alloys...
Detailed studies of the luminescent properties of the Si-based 2D photonic crystal (PhC) slabs with air holes of various depths are reported. Ge self-assembled quantum dots served as an internal light source. It was obtained that changing the air hol...
Nickel-cobalt spinel catalyst (NCO) is a promising catalyst for air oxidation of humic acid, which is a typical natural refractory organic matter and a precursor of toxic disinfection by-products. In this study, reductive etchers, NaBH4 or Na2SO3, we...
This study compared the shear bond strength (SBS) and micromorphology of composite resin to human dentin after pre-treatment with silica-modified aluminum oxide air abrasion. Forty-six molar teeth were treated with either Scotchbond Multi-Purpose (SC...
The purposes of this study were to evaluate the efficacy of water–airborne-particle abrasion (WAPA) as pre-etching procedure for tooth surfaces to increase bond strength, and to compare the survival rate of WAPA vs. non-WAPA glass–ceramic restoration...
Adhesion of zirconia is difficult; thus, etching agents using several different methods are being developed. We investigated the effects of surface treatment with commercially available etching agents on the bond strength between zirconia and resin c...
Background/Objectives: Air particle abrasion (APA) is a common surface preparation method in dentistry, particularly for improving bond strength to dentin. This review evaluates the influence of APA on dentin adhesion. Methods: A systematic literatur...
Background: The aim of this study was to test the impact of hot acids etching and two types of adhesive cement on the retention of zirconia crowns. Methods: Forty maxillary premolars were prepared, and zirconia crowns were designed and fabricated wit...
This study aimed to evaluate the effect of the adhesive application method on the durability of the enamel bond and the thickness of the adhesive layer. A new-generation two-step universal adhesive system, G2-Bond Universal, and two conventional two-...
The aim of this work was to evaluate the effects of application time of an acid mixture solution on the surface roughness, phase transformation, and biaxial flexural strength of 3Y-TZP after sintering or air abrasion. For the biaxial flexural strengt...
Glass-ceramic spray deposition (GCSD) is a novel technique for coating lithium disilicate (LD) glass-ceramics onto zirconia through simple tempering steps. GCSD has been proven to improve the bonding of zirconia to resin cement, but the effect of etc...
Objective: To investigate the effect of various surface conditioning protocols on the shear bond strength between 3D-printed dental composite resin and feldspathic ceramic rods using Panavia V5 resin cement. Methods: 3D-printed composite resin discs...
This in vitro study was conducted to evaluate the shear bond strength of “non-self-adhesive” resin to dental zirconia etched with hydrofluoric acid (HF) at room temperature and to compare it to that of air-abraded zirconia. Sintered zirconia plates...
The effect of etching solution on the synthesis process of two-dimensional vanadium carbide (V2C MXene) was researched. Three etching solutions were used to etch ternary carbide V2AlC at 90 °C. The three solutions were: lithium fluoride + hydroch...
In this work, we investigate theoretically the reflective polarization rotator in a silicon waveguide formed by periodically arranged rectangular air holes. The etched air holes generate the large birefringence for the waveguide. The effective refrac...
Controlling the surface morphology and composition of the perovskite substrates is a critical aspect in tuning the final properties of the deposited films and of their interfaces. The paper reports on a chemical etching method developed for (110) and...
We report a cost-effective and scalable methodology for producing a hierarchical micro-/nanostructured silicon surface solely by metal-assisted chemical etching. It involves two major processing steps of fabricating micropillars and nanowires separat...
Current solutions for improving the light extraction efficiency of flip-chip light-emitting diodes (LEDs) mainly focus on relieving the total internal reflection at sapphire/air interface, but such methods hardly affect the epilayer mode photons. We...
An intrinsic Fabry-Perot interferometeric sensor based on a microfiber has been demonstrated. The micro-size suspended core is created by chemical etching a photonics crystal fiber, of which the cladding has a micrometer-spaced, hexagonal array of ai...
(1) Background: This study aimed to assess how two different adhesive solvent evaporation techniques affect the microtensile bond strength (µTBS) of a universal adhesive to dentin, as well as the enzymatic activity of dentinal matrix metallopro...
We present a novel method of surface processing of complex polymer-metal composite substrates. Atmospheric-pressure plasma etching in pure H2, N2, H2/N2 and air plasmas was used to fabricate flexible transparent composite poly(methyl methacrylate) (P...
Debonding and detachment of artificial teeth from the denture base is frequently encountered in prosthodontic practice. This study aims to assess the effect of modifications in the ridge-lap surface of denture teeth with various combinations of mecha...
Metalenses play an important role in optoelectronic integrated devices, given their advantages in miniaturization and integration. Due to its high aspect ratio subwavelength structure, fabricating metalenses requires a high-level dry etching technolo...
WO3-based electrochemical transistors (ECTs) are recognized as candidates for three-terminal memristors due to their high on–off ratio, long retention time, and rapid switching speed. However, their patterned fabrication often relies on complex...
This study evaluated the shear bond strength (SBS) and biaxial flexural strength (BFS) of resin cements according to the surface treatment method using low-temperature hot etching with hydrofluoric acid (HF) on a yttrium-stabilized tetragonal zirconi...
Diamond etching in high-temperature ambient-pressure experiments has been performed aimed to assess possible postimpact effects on diamonds in impact craters, for the case of the Popigai crater in Yakutia (Russia). The experiments with different etch...
Three-dimensional printed nitinol (NiTi) alloys have broad prospects for application in medicine due to their unique mechanical properties (shape memory effect and superplasticity) and the possibilities of additive technologies. However, in addition...
Using a graphite crucible as the counter-electrode, platinum microprobes with an aspect ratio of 30 and a tip apex radius less than 100 nm were fabricated by an electrochemical discharge etching process. The “neck-in” structure on the platinum wire i...
Dental implant therapy is a well-accepted treatment modality. Despite good predictability and success in the early stages, the risk of postplacement inflammation in the long-term periods remains an urgent problem. Surgical access and decontamination...
Organic-inorganic halide perovskite materials are considered excellent active layers in the fabrication of highly efficient and low-cost photovoltaic devices. This contribution demonstrates that rapid and low-temperature air-plasma treatment of mixed...
The tensile bond strength between zirconia subjected to different surface-pretreatment methods and methacryloyloxydecyl-dihydrogen-phosphate (MDP)-containing self-adhesive resin cement was evaluated herein. Eighty-eight cylindrical zirconia specimens...
Porous Nb2O5 films obtained by a modified hard-template method were studied and their optical and sensing properties were optimized in order to find applications in chemo-optical sensing. Porous films were prepared by following three steps: liquid mi...
Polyethylene terephthalate (PET) is a polyester used in the beverage bottling industry that generates a serious pollution problem. Films were obtained to reuse discarded PET bottles, and their surface was modified to determine their effectiveness in...
Effective high-aspect-ratio molds that minimize vacuum processes are becoming increasingly important for producing metalenses and other devices. To fabricate a high-aspect-ratio structure, a metal film must be used as a mask for dry etching, typicall...
We report a systematical study on the liquid assisted femtosecond laser machining of quartz plate in water and under different etching solutions. The ablation features in liquid showed a better structuring quality and improved resolution with 1/3~1/2...
This paper presents a micro-scale air flow sensor based on a free-standingcantilever structure. In the fabrication process, MEMS techniques are used to deposit asilicon nitride layer on a silicon wafer. A platinum layer is deposited on the silicon ni...
The present study aimed to evaluate the effect of air-abrasion as a dentin pre-treatment on the bond strength of contemporary adhesive systems. The bonding approaches included etch-and-rinse (ER), self-etch (SE) and universal (UN) adhesive systems, w...
This study evaluated the influence of different surface treatments and composite materials on the microtensile bond strength (μTBS) of repaired aged bulk-fill resin composite restorations, aligning with the principles of minimal intervention denti...
of 4