Skip to Content

1,187 Results Found

  • Article
  • Open Access
4 Citations
2,373 Views
11 Pages

Effect of B2 Precipitation on Hot Ductility of Fe–22Mn–9Al–0.6C Low-Density Steel

  • Jun Wang,
  • Tinghui Man,
  • Yihao Zhou,
  • Xicheng Wei and
  • Han Dong

19 June 2024

Fe–Mn–Al–C low-density steels are regarded as promising materials applied in the automotive industry to achieve the minimization of vehicular emissions and fuel consumption. This study investigates the high-temperature strength and...

(This article belongs to the Special Issue Novel Insights and Advances in Steels and Cast Irons)
  • Article
  • Open Access
7 Citations
2,144 Views
12 Pages

28 January 2024

Secondary phase precipitation in Fe-22Mn-9Al-0.6C low-density steel was investigated during a continuous cooling process with different cooling rates through a DIL805A thermal expansion dilatometer, and the changes in microstructures and hardness by...

(This article belongs to the Section Metals and Alloys)
  • Article
  • Open Access
3 Citations
1,899 Views
15 Pages

4 September 2025

This study investigated the hydrogen embrittlement behavior of Fe-28Mn-10Al-1C-(0,3) Cu austenitic low-density steels after hydrogen charging. Electrochemical hydrogen charging and thermal desorption spectroscopy (TDS) were employed to characterize h...

(This article belongs to the Section Metals and Alloys)
  • Article
  • Open Access
11 Citations
2,742 Views
14 Pages

26 January 2021

In the last decades, low-density steels for forging have increasing interest in the automotive industry, and good mechanical properties are required for their real application. This paper describes the results obtained for a 0.66C11.4Mn9.9Al duplex a...

(This article belongs to the Special Issue Heat Treatment of Steels)
  • Article
  • Open Access
14 Citations
2,683 Views
10 Pages

3 June 2024

This study compares the hydrogen embrittlement susceptibility of a Fe-30Mn-8Al-1.2C austenitic low-density steel aged at 600 °C for 0 (RX), 1 min (A1) and 60 min (A60), each exhibiting varying sizes and distributions of nano-sized κ-carbide...

(This article belongs to the Special Issue Enhancing In-Use Properties of Advanced Steels)
  • Article
  • Open Access
9 Citations
4,205 Views
10 Pages

Tensile Properties and Microstructure Evolutions of Low-Density Duplex Fe–12Mn–7Al–0.2C–0.6Si Steel

  • Shuai Liu,
  • Yinlei Ge,
  • Huanyou Liu,
  • Junyu Liu and ,
  • Yunli Feng,
  • Chen Chen and
  • Fucheng Zhang
  • + 2 authors+ 0 author

28 March 2022

An austenite-ferrite duplex low-density steel (Fe–12Mn–7Al–0.2C–0.6Si, wt%) was designed and fabricated by cold rolling and annealing at different temperatures. The tensile properties, microstructure evolution, deformation mec...

(This article belongs to the Topic Metallurgical and Materials Engineering)
  • Article
  • Open Access
6 Citations
3,359 Views
16 Pages

Microstructure and Continuous Cooling Transformation of an Fe-7.1Al-0.7Mn-0.4C-0.3Nb Alloy

  • Mônica Aline Magalhães Gurgel,
  • Eustáquio de Souza Baêta Júnior,
  • Rodolfo da Silva Teixeira,
  • Gabriel Onofre do Nascimento and ,
  • Suzane Sant’Ana Oliveira,
  • Duílio Norberto Ferronatto Leite,
  • Luciano Pessanha Moreira,
  • Luiz Paulo Brandao and
  • Andersan dos Santos Paula
  • + 4 authors+ 0 author

3 August 2022

Reducing pollutant emissions and improving safety standards are primary targets for modern mobility improvement. To meet these needs, the development of low-density steels containing aluminum is a new frontier of research for automotive applications....

(This article belongs to the Section Metal Casting, Forming and Heat Treatment)
  • Feature Paper
  • Article
  • Open Access
15 Citations
4,315 Views
20 Pages

Assessing the Potential of the DART Model to Discrete Return LiDAR Simulation—Application to Fuel Type Mapping

  • Sergio Revilla,
  • María Teresa Lamelas,
  • Darío Domingo,
  • Juan de la Riva and ,
  • Raquel Montorio,
  • Antonio Luis Montealegre and
  • Alberto García-Martín
  • + 2 authors+ 0 author

20 January 2021

Fuel type is one of the key factors for analyzing the potential of fire ignition and propagation in agricultural and forest environments. The increase of three-dimensional datasets provided by active sensors, such as LiDAR (Light Detection and Rangin...

(This article belongs to the Special Issue Feature Paper Special Issue on Forest Remote Sensing)
  • Article
  • Open Access
17 Citations
6,261 Views
29 Pages

25 October 2024

Three raster-based (RB) and one point cloud-based (PCB) algorithms were tested to segment individual Aleppo pine trees and extract their tree height (H) and crown diameter (CD) using two types of point clouds generated from two different techniques:...

(This article belongs to the Special Issue Dynamic Monitoring of Forest Resources Based on Multi-Source Remote Sensing Data)
  • Article
  • Open Access
11 Citations
3,087 Views
15 Pages

Titanium Alloy Ti-6Al-4V Electrochemical Dissolution Behavior in NaNO3 and NaCl Solutions at Low Current Density

  • Shen Niu,
  • Changyang Yu,
  • Pingmei Ming,
  • Siru Wang and ,
  • Ge Qin,
  • Xinchao Li and
  • Huan Liu
  • + 2 authors+ 0 author

14 October 2024

Jet electrochemical micromilling (JEMM) exhibits significant potential for high-efficiency and high-quality machining of titanium alloy microstructures. However, during the JEMM process, the machined surface of the workpiece inevitably experiences st...

  • Article
  • Open Access
8 Citations
2,729 Views
18 Pages

Microstructure and Constitutive Equation of Hot Compressive Fe-15Mn-15Al-5Ni-1C Low-Density Steel

  • Yingjie Wang,
  • Fengya Hu,
  • Zhongjun Wang,
  • Kuijun Fu and ,
  • Weijuan Li,
  • Jiaji Wang and
  • Jing Guo
  • + 2 authors+ 0 author

7 April 2022

The hot deformation behavior and dynamic recrystallization (DRX) of Fe-15Mn-15Al-5Ni-1C low-density steel in the as-cast state was investigated via hot compression experiments over temperature and strain rate ranges of 925 to 1150 °C and 0.01 to...

(This article belongs to the Section Metals and Alloys)
  • Article
  • Open Access
9 Citations
2,708 Views
11 Pages

17 May 2022

The precipitation behavior of κ-carbide and its effects on mechanical properties in Fe-30Mn-xAl-1C (x = 7–11%) steels under water quenching and furnace cooling are studied in the present paper. TEM, XRD, EPMA were employed to characterize...

(This article belongs to the Special Issue Advanced Structural Steels and Alloys)
  • Article
  • Open Access
  • Best Paper Award
35 Citations
5,371 Views
11 Pages

15 March 2022

Low-density materials show promising prospects for industrial application in engineering, and have remained a research hotspot. The ingots of Al15Zr40Ti28Nb12Cr5, Al15Zr40Ti28Nb12Mo5 and Al15Zr40Ti28Nb12Si5 high-entropy alloys were prepared using an...

(This article belongs to the Special Issue Amorphous and High-Entropy Alloy Coatings)
  • Article
  • Open Access
14 Citations
2,786 Views
17 Pages

24 April 2024

In this study, the synergistic behavior of Ni and Al in two low-density steels (Fe-26Mn-10.2Al-0.98C-0.15V (wt. %) and Fe-29Mn-5Al-1C-12Ni (wt. %)) and their influence on microstructures and mechanical properties were investigated. The chemical compo...

  • Article
  • Open Access
14 Citations
4,913 Views
11 Pages

Kappa Carbide Precipitation in Duplex Fe-Al-Mn-Ni-C Low-Density Steel

  • Jaka Burja,
  • Barbara Šetina Batič and
  • Tilen Balaško

18 October 2021

The microstructural evolution of a Fe-Mn-Al-Ni-C low-density steel was studied. The lightweight low-density steels are a promising material for the transportation industry, due to their good mechanical properties and low density. The base microstruct...

(This article belongs to the Special Issue Advance in Alloy Materials)
  • Review
  • Open Access
72 Citations
9,593 Views
14 Pages

29 July 2020

Fe-Mn-Al-C steels exhibit an outstanding combination of strength and ductility, and the addition of aluminum drastically reduces the density of steels. The low density also offers the advantage of lightweight structures compared with other alloys in...

  • Article
  • Open Access
8 Citations
3,427 Views
11 Pages

28 May 2022

Low-density multi-principal element alloys (MPEAs) combining a high specific strength and considerable ductility have remained a research hotspot, due to their promising prospects for energy-saving industrial applications. Light Ti-containing AlNbZrT...

  • Communication
  • Open Access
8 Citations
3,611 Views
10 Pages

Dynamic Compressive Mechanical Behavior and Microstructure Evolution of Rolled Fe-28Mn-10Al-1.2C Low-Density Steel

  • Hao Wu,
  • Yan Tan,
  • Abdul Malik,
  • Yangwei Wang and ,
  • Syed Zohaib Hassan Naqvi,
  • Huanwu Cheng,
  • Jiebin Tian and
  • Xianming Meng
  • + 3 authors+ 0 author

16 May 2022

In this study, the quasi-static and dynamic compressive mechanical behavior of a rolled Fe-28Mn-10Al-1.2C steel (low-density) was investigated. X-ray diffraction, optical microscopy, electron backscattered diffraction and transmission electron micros...

  • Article
  • Open Access
9 Citations
3,582 Views
21 Pages

Effect of Nb Alloying and Solution Treatment on the Mechanical Properties of Cold-Rolled Fe-Mn-Al-C Low-Density Steel

  • Litu Huo,
  • Jianxin Gao,
  • Yungang Li,
  • Pengfei Xu and ,
  • Xiangyu Wei and
  • Tao Ma
  • + 1 author+ 0 author

22 January 2025

The automotive industry’s rapid expansion has made the development of lightweight, high-strength automotive steels essential for both energy efficiency and emission reduction. Among these materials, Fe-Mn-Al-C steel has drawn considerable inter...

  • Article
  • Open Access
6 Citations
5,172 Views
22 Pages

Fracture Toughness Analysis of Aluminum (Al) Foil and Its Adhesion with Low-Density Polyethylene (LPDE) in the Packing Industry

  • Umer Sharif,
  • Beibei Sun,
  • Md Shafiqul Islam,
  • Kashif Majeed and ,
  • Dauda Sh. Ibrahim,
  • Orelaja Oluseyi Adewale,
  • Naseem Akhtar,
  • Zaki Ismail Zaki and
  • Zeinhom M. El-Bahy
  • + 4 authors+ 0 author

6 September 2021

Liquid food packages consist of various polymers films, which are bonded together with Aluminum foil (Al-foil) using adhesion or by direct heat. The main aim of this research was to define important material properties such as fracture toughness and...

(This article belongs to the Special Issue Strengthening, Corrosion and Protection of High Temperature Structural Materials)
  • Article
  • Open Access
8 Citations
2,842 Views
18 Pages

Flow Behavior and Microstructure of Hot-Worked Fe-30.9Mn-4.9Al-4.5Cr-0.4C and Fe-21.3Mn-7.6Al-4.3Cr-1C Low-Density Stainless Steels

  • Takatso Komane,
  • Nthabiseng Maledi,
  • Desmond Klenam,
  • Josias van der Merwe and
  • Michael Bodunrin

10 February 2023

Two as-cast low-density steels grades (austenite-based duplex Fe-30.9Mn-4.9Al-4.5Cr-0.4C and austenitic Fe-21.3Mn-7.6Al-4.3Cr-1C) with an initial dendritic microstructure were subjected to hot working conditions to understand the influence of deforma...

(This article belongs to the Special Issue Advanced Metal Forming and Smart Manufacturing Processes)
  • Article
  • Open Access
6 Citations
4,883 Views
11 Pages

1 June 2022

Mold with diameter sizes of 140 mm, 80 mm, 40 mm and 15 mm were designed to obtain the ingot of Fe-30Mn-10Al-1.1C low-density steel under different cooling rates. The influence of cooling rate on the grain morphology and elemental segregation behavio...

  • Article
  • Open Access
2,599 Views
11 Pages

30 July 2022

In the present research, the microstructure and mechanical properties of low-density Fe-0.72Mn-3.7Al-0.53C steel were investigated after solution treatment at 900 °C, 1000 °C, 1110 °C and 1200 °C for 1 h. The density of steel is about...

(This article belongs to the Section Metal Casting, Forming and Heat Treatment)
  • Article
  • Open Access
11 Citations
3,730 Views
19 Pages

Improvements of Fire Fuels Attributes Maps by Integrating Field Inventories, Low Density ALS, and Satellite Data in Complex Mediterranean Forests

  • Roberto Crespo Calvo,
  • Mª Ángeles Varo Martínez,
  • Francisco Ruiz Gómez,
  • Antonio Jesús Ariza Salamanca and
  • Rafael M. Navarro-Cerrillo

11 April 2023

One of the most determining factors in forest fire behaviour is to characterize forest fuel attributes. We investigated a complex Mediterranean forest type—mountainous Abies pinsapo–Pinus–Quercus–Juniperus with distinct struct...

(This article belongs to the Section Environmental Remote Sensing)
  • Article
  • Open Access
14 Citations
2,846 Views
12 Pages

High Temperature Deformation Behavior and Microstructure Evolution of Low-Density Steel Fe30Mn11Al1C Micro-Alloyed with Nb and V

  • Hui Wang,
  • Ziyuan Gao,
  • Zhiyue Shi,
  • Haifeng Xu and ,
  • Ling Zhang,
  • Guilin Wu,
  • Chang Wang,
  • Cunyu Wang,
  • Yuqing Weng and
  • Wenquan Cao
  • + 5 authors+ 0 author

1 November 2021

The thermal processing parameters is very important to the hot rolling and forging process for producing grain refinement in lightweight high-manganese and aluminum steels. In this work, the high temperature deformation behaviors of a low-density ste...

(This article belongs to the Section Metals and Alloys)
  • Article
  • Open Access
23 Citations
4,599 Views
15 Pages

Microband-Induced Plasticity in a Nb Content Fe–28Mn–10Al–C Low Density Steel

  • Tao Ma,
  • Jianxin Gao,
  • Huirong Li,
  • Changqing Li and ,
  • Haichao Zhang and
  • Yungang Li
  • + 1 author+ 0 author

19 February 2021

Novel Fe–28Mn–10Al–C–0.5Nb low-density steel was developed and the room temperature tensile behavior in the solid solution state and the microstructure evolution process during plastic deformation were studied, aiming to clarify the dominant deformat...

  • Article
  • Open Access
4 Citations
2,806 Views
26 Pages

Evaluation of Mechanical Behavior and Application Potential of Totora (Schoenoplectus californicus)-and-Recycled Low-Density Polyethylene–Aluminum (LDPE–Al) Hybrid Panels

  • Oscar Jara-Vinueza,
  • Wilson Pavon,
  • Abel Remache,
  • Flavio Arroyo and ,
  • Michael Gutiérrez and
  • Edgar Mora Figueroa
  • + 1 author+ 0 author

24 June 2025

The growing demand for sustainable materials has driven significant interest in composites reinforced with organic fibers, due to their mechanical performance, availability, and reduced environmental impact. This study investigates the mechanical beh...

(This article belongs to the Section Building Materials, and Repair & Renovation)
  • Article
  • Open Access
30 Citations
5,032 Views
14 Pages

Effect of Content and Surface Modification of Fique Fibers on the Properties of a Low-Density Polyethylene (LDPE)-Al/Fique Composite

  • Mario Fernando Muñoz-Vélez,
  • Miguel Angel Hidalgo-Salazar and
  • Jose Herminsul Mina-Hernández

20 September 2018

This work presents the physical-thermal and mechanical characterization of a low-density polyethylene (LDPE)-Al matrix composite material that was obtained from reinforcing recycled (post-consumer) long-life Tetra Pak packages with fique natural fibe...

(This article belongs to the Special Issue Modification of Natural Fibres to Improve Biocomposites Performances)
  • Article
  • Open Access
8 Citations
4,360 Views
8 Pages

5 April 2021

We demonstrate the highly efficient, GaN-based, multiple-quantum-well light-emitting diodes (LEDs) grown on Si (111) substrates embedded with the AlN buffer layer using NH3 growth interruption. Analysis of the materials by the X-ray diffraction omega...

(This article belongs to the Special Issue Wide Bandgap Based Devices: Design, Fabrication and Applications, Volume II)
  • Article
  • Open Access
26 Citations
7,152 Views
24 Pages

Identifying Forest Structural Types along an Aridity Gradient in Peninsular Spain: Integrating Low-Density LiDAR, Forest Inventory, and Aridity Index

  • Julián Tijerín-Triviño,
  • Daniel Moreno-Fernández,
  • Miguel A. Zavala,
  • Julen Astigarraga and
  • Mariano García

5 January 2022

Forest structure is a key driver of forest functional processes. The characterization of forest structure across spatiotemporal scales is essential for forest monitoring and management. LiDAR data have proven particularly useful for cost-effectively...

(This article belongs to the Topic Climate Change and Environmental Sustainability)
  • Article
  • Open Access
3 Citations
3,851 Views
9 Pages

14 March 2023

In this work, we analyze a resistive switching random access memory (RRAM) device with the metal–insulator–metal structure of Al/αTiOx/Al. The transport mechanism of our RRAM device is trap-controlled space-charge limited conduction...

(This article belongs to the Special Issue Advances in Semiconductor and Dielectric Materials)
  • Article
  • Open Access
22 Citations
5,669 Views
14 Pages

6 April 2023

Plastic pollution is one of the most serious environmental issues, causing severe environmental damage. It is of vital importance to find an efficient and eco-friendly approach to biodegrading plastics. The aim of this study was to isolate and charac...

(This article belongs to the Section Environmental Sciences)
  • Article
  • Open Access
26 Citations
5,688 Views
9 Pages

7 April 2020

Refractory high-entropy alloys (RHEAs) Al20+xCr20-xMo20-yTi20V20+y ((x, y) = (0, 0), (0, 10), and (10, 15)) were computationally studied to obtain a low density and a better mechanical property. The density functional theory (DFT) method was employed...

(This article belongs to the Special Issue Crystal Plasticity)
  • Article
  • Open Access
7 Citations
3,765 Views
9 Pages

19 June 2023

In this study, we present a detailed analysis of trapping characteristics at the AlxGa1−xN/GaN interface of AlxGa1−xN/GaN high-electron-mobility transistors (HEMTs) with reliability assessments, demonstrating how the composition of the Al...

  • Article
  • Open Access
14 Citations
6,034 Views
15 Pages

Carbon Sequestration in Carob (Ceratonia siliqua L.) Plantations under the EU Afforestation Program in Southern Spain Using Low-Density Aerial Laser Scanning (ALS) Data

  • Guillermo Palacios-Rodríguez,
  • Luis Quinto,
  • Miguel A. Lara-Gómez,
  • Javier Pérez-Romero and ,
  • José Manuel Recio,
  • Marta Álvarez-Romero,
  • Antonio M. Cachinero-Vivar,
  • Salvador Hernández-Navarro and
  • Rafael M. Navarro-Cerrillo
  • + 4 authors+ 0 author

10 February 2022

Climate change is one of the environmental issues of global dominance and public opinion, becoming the greatest environmental challenge and of interest to researchers. In this context, planting trees on marginal agricultural land is considered a favo...

(This article belongs to the Special Issue Adaptive Forest Management to Climatic Change)
  • Article
  • Open Access
21 Citations
4,874 Views
8 Pages

Tensile Behavior and Deformation Mechanism of Fe-Mn-Al-C Low Density Steel with High Strength and High Plasticity

  • Jingyu Pang,
  • Zhanming Zhou,
  • Zhengzhi Zhao,
  • Di Tang and ,
  • Juhua Liang and
  • Qing He
  • + 1 author+ 0 author

16 August 2019

Tensile behavior and plastic deformation mechanisms of Fe-22.8Mn-8.48Al-0.86C low-density steel were studied in this thesis. After solution treatment 1100 °C for 1 h; the steels obtained an excellent combination in mechanical properties; with ten...

  • Article
  • Open Access
15 Citations
3,481 Views
10 Pages

Effect of κ Carbides on Deformation Behavior of Fe-27Mn-10Al-1C Low Density Steel

  • Siyuan Li,
  • Dazhao Li,
  • Haitao Lu,
  • Pengfei Cao and
  • Ruofei Xie

17 July 2022

Fe-Mn-Al-C steel, which is a potential lightweight material for automobiles, has a variety of microstructures and good mechanical properties. The effect of κ carbides on the mechanical properties and strain hardening rate of Fe-27Mn-10Al-1C (wt...

(This article belongs to the Special Issue Structural Changes during Steel Processing)
  • Feature Paper
  • Review
  • Open Access
17 Citations
4,571 Views
16 Pages

Research Progress of Low Density and High Stiffness of Be-Al Alloy Fabricated by Investment Casting

  • Junyi Li,
  • Yao Xie,
  • Yiqun Yang,
  • Zhaogang Liu and ,
  • Dongxin Wang and
  • Yajun Yin
  • + 1 author+ 0 author

19 August 2022

Be-Al alloy is a type of in situ metal matrix composite composed of a primary Be phase for strength and stiffness and a continuous Al matrix for ductility and toughness. Be-Al alloy (AlBe-Cast®910) has the characteristics of low density (2.17 g/c...

(This article belongs to the Special Issue Light Alloy and Its Application)
  • Article
  • Open Access
7 Citations
2,069 Views
17 Pages

26 November 2024

In this study, a novel lightweight Fe-Mn-Al-C steel composition and thermomechanical processing route was developed to produce a fully austenitic microstructure with a uniform intragranular dispersion of B2-NiAl precipitation in order to overcome the...

(This article belongs to the Section Metal Casting, Forming and Heat Treatment)
  • Article
  • Open Access
9 Citations
3,460 Views
13 Pages

Nano-Scaled Creep Response of TiAlV Low Density Medium Entropy Alloy at Elevated Temperatures

  • Xiangkai Zhang,
  • Hanting Ye,
  • Jacob C. Huang,
  • Taiyou Liu and ,
  • Pinhung Lin,
  • Yaocheng Wu,
  • Mintsang Tsai,
  • Yuchin Liao and
  • Jason S. C. Jang
  • + 4 authors+ 0 author

20 December 2019

A low density, medium entropy alloy (LD-MEA) Ti33Al33V34 (4.44 g/cm3) was successfully developed. The microstructure was found to be composed of a disordered body-centered-cubic (BCC) matrix and minor ordered B2 precipitates based on transmission ele...

  • Article
  • Open Access
9 Citations
2,045 Views
22 Pages

14 September 2023

Oxidation results in the formation of an oxide film whose properties and structure can be tailored by controlling the oxidation conditions. Reactive molecular dynamics simulations were performed to study thermal oxidation of polycrystalline Al substr...

(This article belongs to the Section Crystalline Metals and Alloys)
  • Article
  • Open Access
2 Citations
3,285 Views
19 Pages

Mechanical Properties of High Carbon Low-Density Steels

  • Jiří Hájek,
  • Zbyšek Nový,
  • Ludmila Kučerová,
  • Hana Jirková and ,
  • Črtomir Donik and
  • Zdeněk Jansa
  • + 1 author+ 0 author

19 May 2023

The paper presents the possibilities of heat treatment of low-density structural steels usable for springs. Heats have been prepared with chemical compositions 0.7 wt% C and 1 wt% C, as well as 7 wt% Al and 5 wt% Al. Samples were prepared from ingots...

(This article belongs to the Special Issue Heat Treatment of Metallic Materials in Modern Industry)
  • Article
  • Open Access
60 Citations
5,324 Views
15 Pages

Novel Ultralight-Weight Complex Concentrated Alloys with High Strength

  • Yuefei Jia,
  • Yandong Jia,
  • Shiwei Wu,
  • Xindi Ma and
  • Gang Wang

8 April 2019

To explore a novel high strength and low modulus ultralight-weight complex concentrated alloys (ULW-CCAs), a series of light alloys are designed and explored based on some low-density and low modulus elements, such as Al, Li, Mg, Ca, Si, and Y. An Al...

  • Article
  • Open Access
9 Citations
4,898 Views
9 Pages

The Effect of Strain Rate on the Deformation Behavior of Fe-30Mn-8Al-1.0C Austenitic Low-Density Steel

  • Jiahui Du,
  • Peng Chen,
  • Xianjun Guan,
  • Jiawei Cai and ,
  • Qian Peng,
  • Chuang Lin and
  • Xiaowu Li
  • + 2 authors+ 0 author

18 August 2022

Automotive steels suffer different strain rates during their processing and service. In this study, the effect of strain rates on the tensile properties of fully austenitic Fe-30Mn-8Al-1.0C (wt.%) steel was investigated, and the dominant deformation...

(This article belongs to the Special Issue Deformation, Fracture and Microstructure of Metallic Materials)
  • Article
  • Open Access
38 Citations
5,701 Views
26 Pages

Estimating Stand and Fire-Related Surface and Canopy Fuel Variables in Pine Stands Using Low-Density Airborne and Single-Scan Terrestrial Laser Scanning Data

  • Cecilia Alonso-Rego,
  • Stéfano Arellano-Pérez,
  • Juan Guerra-Hernández,
  • Juan Alberto Molina-Valero and ,
  • Adela Martínez-Calvo,
  • César Pérez-Cruzado,
  • Fernando Castedo-Dorado,
  • Eduardo González-Ferreiro,
  • Juan Gabriel Álvarez-González and
  • Ana Daría Ruiz-González
  • + 5 authors+ 0 author

20 December 2021

In this study, we used data from a thinning trial conducted on 34 different sites and 102 sample plots established in pure and even-aged Pinus radiata and Pinus pinaster stands, to test the potential use of low-density airborne laser scanning (ALS) m...

(This article belongs to the Special Issue 3D Point Clouds in Forest Remote Sensing II)
  • Article
  • Open Access
7 Citations
1,516 Views
14 Pages

Quantifying Stress Shielding in Dental Implants: A Comparative Finite Element Study of Titanium, CFR-PEEK, and Ceramic Materials

  • Mario Ceddia,
  • Tea Romasco,
  • Natalia Di Pietro,
  • Alessandro Cipollina and ,
  • Adriano Piattelli,
  • Luciano Lamberti and
  • Bartolomeo Trentadue
  • + 2 authors+ 0 author

26 February 2026

Background: Stress shielding, which occurs when there is a mismatch between the stiffness of the implant and the bone, can alter load transfer and drive peri-implant bone remodeling, particularly in low-density bone. Methods: We compared the biomecha...

(This article belongs to the Section Biomaterials)
  • Article
  • Open Access
18 Citations
3,765 Views
20 Pages

Microstructural Constituents and Mechanical Properties of Low-Density Fe-Cr-Ni-Mn-Al-C Stainless Steels

  • Steffen Scherbring,
  • Guanghui Chen,
  • Bastian Veltel,
  • Gert Bartzsch and ,
  • Julia Richter,
  • Malte Vollmer,
  • Malte Blankenburg,
  • Saikat Shyamal,
  • Olena Volkova and
  • Javad Mola
  • + 8 authors+ 3 authors

23 July 2022

Metallic material concepts associated with the sustainable and efficient use of resources are currently the subject of intensive research. Al addition to steel offers advantages in view of lightweight, durability, and efficient use of high-Fe scrap f...

(This article belongs to the Special Issue Phase Transformation and Microstructure Evolution in Stainless Steels)
  • Article
  • Open Access
3 Citations
2,211 Views
19 Pages

Study on the Austenite Grain Growth Behavior of Fe-Mn-Al-C Low-Density Steel Containing Niobium

  • Litu Huo,
  • Tao Ma,
  • Weimin Gao,
  • Yungang Li and ,
  • Haichao Zhang and
  • Jianxin Gao
  • + 1 author+ 0 author

23 May 2025

To explore the impact of niobium (Nb) addition on the austenitization behavior of Fe-Mn-Al-C lightweight steels, the effects were examined through Thermo-Calc thermodynamic simulations, optical microscopy, transmission electron microscopy (TEM), and...

  • Article
  • Open Access
26 Citations
3,757 Views
13 Pages

A Lightweight AlCrTiV0.5Cux High-Entropy Alloy with Excellent Corrosion Resistance

  • Zhen Peng,
  • Baowei Li,
  • Zaibin Luo,
  • Xuefei Chen and ,
  • Yao Tang,
  • Guannan Yang and
  • Pan Gong
  • + 2 authors+ 0 author

6 April 2023

Lightweight high-entropy alloys (HEAs) are a new class of low-density, high strength-to-weight ratio metallic structural material. Understanding their corrosion behavior is crucial for designing microstructures for their practical applications. This...

(This article belongs to the Special Issue Physical Metallurgy of Metals and Alloys)
  • Feature Paper
  • Article
  • Open Access
14 Citations
4,528 Views
14 Pages

Improved Chaff-Based CMIX for Solving Location Privacy Issues in VANETs

  • Mishri Saleh Al-Marshoud,
  • Ali H. Al-Bayatti and
  • Mehmet Sabir Kiraz

Safety application systems in Vehicular Ad-hoc Networks (VANETs) require the dissemination of contextual information about the scale of neighbouring vehicles; therefore, ensuring security and privacy is of utmost importance. Vulnerabilities in the me...

(This article belongs to the Section Electrical and Autonomous Vehicles)

of 24