Spin-freeze-drying is a promising technique to enable long-term storage of pharmaceutical unit doses of aqueous drug solutions. To investigate the sublimation of the ice during the primary phase of freeze-drying, X-ray imaging can yield crucial tempo...
Recent advances in high resolution X-ray tomography (μCT) technology have enabled in-situ dynamic μCT imaging (4D-μCT) of time-dependent processes inside 3D structures, non-destructively and non-invasively. This paper illustrates the application of 4...
Several methods, including X-ray radiography, have been developed for the investigation of the characteristics of water-saturated quasi-brittle materials. Here, the water content is one of the most important factors influencing their strength and fra...
In this work, the microstructural evolution during the dynamic transformation of austenite to bainite was directly observed by in-situ high energy synchrotron X-ray diffraction measurements during warm uniaxial compression performed at the P07 beamli...
This work aims to identify the mechanisms of restoration occurring in Ti-6Al-4V during hot plastic deformation and subsequent heat treatment. The allotropic phase transformation that occurs during cooling distorts the interpretation of the restoratio...
Organic solar cells, characterized by a symmetrical regular layered structure, are very promising systems for developing green, low cost, and flexible solar energy conversion devices. Despite the efficiencies being appealing (over 17%), the technolog...
The mechanical properties of laser powder bed fused (LPBFed) Invar 36 alloy have been limited by the presence of manufacturing defects. It is imperative to investigate the influence of these defects on the mechanical behavior of LPBFed Invar 36 alloy...
In order to study the fracture behavior and structure evolution of 1,3,5-Triamino-2,4,6-Trinitrobenzene (TATB)-based polymer bonded explosive in thermal-mechanical loading, in-situ studies were performed on X-ray computed tomography system using quas...
AFt is one of the major products at the early stage of cement hydration. It is an important product that influences the performance of the fresh and hardened cement pastes such as the setting time. However, there is a lack of detailed investigation o...
Starting from subsurface Zr0-doped “inverse” Pd and bulk-intermetallic Pd0Zr0 model catalyst precursors, we investigated the dry reforming reaction of methane (DRM) using synchrotron-based near ambient pressure in-situ X-ray photoelectron...
In-situ investigations of structural transitions during the thermal-oxidative event of mixed-metal spinel oxide precursors, the so-called nickel- (NCO) and zinc-containing (ZCO) cobaltite spinel precursors, were investigated to understand the formati...
On the basis of the major application for block copolymers to use them as separation membranes, lithographic mask, and as templates, the preparation of highly oriented nanoporous thin films requires the selective removal of the minor phase from the p...
Investigation of biofilms and visualization using non-destructive imaging techniques like X-ray μCT has recently gained interest. Biofilms are congregations of microorganisms that attach to surfaces and comprise of microbial cells embedded in extr...
In this study, the effects of ultrasonic on melt pool dynamic, microstructure, and properties of underwater wet flux-cored arc welding (FCAW) joints were investigated. Ultrasonic vibration enhanced melt flow and weld pool oscillation. Grain fragmenta...
Renewable technologies, and in particular the electric vehicle revolution, have generated tremendous pressure for the improvement of lithium ion battery performance. To meet the increasingly high market demand, challenges include improving the energy...
In order to clarify the mechanical features of a metal under thermal cyclic loading for the system Ni30Cr-
Copper and copper oxide electrode surfaces are suitable for the electrochemical reduction of CO2 and produce a range of products, with the product selectivity being strongly influenced by the surface structure of the copper electrode. In this paper,...
Investigations on comb crack resistance of milling inserts coated with chemical vapor deposition (CVD) Ti(C,N)/α-Al2O3 and Zr(C,N)/α-Al2O3 showed a distinct wear evolution in both systems. Wear studies revealed that the appearance of comb cracks is c...
In optical crystals, photodarkening will occur after they were irradiated with high-energy particles, and such induced optical loss generally results in significant performance degradation whether they are used as passive or active optical elements....
This study presents a non-invasive in situ methodology based on the use of portable elemental (energy dispersive X-ray fluorescence spectroscopy, EDXRF) and molecular (Raman spectroscopy) spectroscopic-based instrumentation as a tool to obtain prelim...
Hot working tool steel (AISI H13) is one of the most common die materials used in casting industries. A die suffers from damage due to friction and wear during its lifetime. Therefore, various methods have been developed for its repair to save costs...
The transient nature of the internal pore structure of particulate wall flow filters, caused by the continuous deposition of particulate matter, makes studying their flow and filtration characteristics challenging. In this article we present a new me...
Molybdenum carbide (Mo2C) with a Pt-like d-band electron structure exhibits certain activities for oxygen reduction and evolution reactions (ORR/OER) in alkaline solutions, but it is questioned due to its poor OER stability. Combining Mo2C with trans...
In laser powder bed fusion processes, keyholes are the gaseous cavities formed where laser interacts with metal, and their morphologies play an important role in defect formation and the final product quality. The in-situ X-ray imaging technique can...
The oxidation of palladium nanoparticles causes the performance degradation of alkaline direct ethanol fuel cells. Quantifying this oxidation is a task of tremendous importance to design mitigation strategies that extend the service life of catalysts...
Understanding biaxial deformation is essential for a more realistic evaluation of rubber elasticity compared to the more usual uniaxial deformation. To study crystallisation occurring during biaxial deformation of natural rubber films, a new simple e...
A flow-through reaction cell has been developed for studying minerals leaching by in-situ time-resolved powder X-ray diffraction, allowing for a better understanding of the leaching mechanisms and kinetics. The cell has the capability of independent...
The phase transformations occurring during the heat treatments leading to transformation-induced plasticity (TRIP)-aided bainitic steel have been investigated in-situ by high-energy X-ray diffraction (HEXRD) conducted with synchrotron light at 90 keV...
The deformation behavior of semi-crystalline polymers is strongly dependent on the morphology formed during processing. In this study, in-situ synchrotron X-ray was firstly used to identify the morphological distributions of injection-molded isotacti...
In-situ high energy X-Ray diffraction (HEXRD) was used on compositionally graded steels to study the effect of substitutional elements on ferrite growth kinetics in Fe–C–X and Fe–C–X–Y systems. Two systems were selected...
The intercalation degree of nanoclays in polymeric foamed nanocomposites containing clays is a key parameter determining the final properties of the material, but how intercalation occurs is not fully understood. In this work, energy dispersive X-ray...
Various types of 2D organic–inorganic perovskite solar cells have been developed and investigated due to better electron transport behavior and environmental stability. Controlling the formation of phases in the 2D perovskite films has been con...
We developed a stress sensor for in-situ deformation experiments using synchrotron radial X-ray diffraction. This stress sensor provided nearly diffraction-plane-independent stress that, when used in series with a sample, reduced the uncertainty of t...
The oxidation behaviour of chemical vapour deposited ZrN, ZrC and ZrCN coatings was investigated using in-situ synchrotron X-ray diffraction (XRD). To obtain a precise analysis of the temperature–dependent phase evolution during oxidation, coating po...
We report on formation of a bicontinuous double gyroid phase by a wedge-shaped amphiphilic mesogen, pyridinium 4′-[3″,4″,5″-tris-(octyloxy)benzoyloxy]azobenzene-4-sulfonate. It is found that this compound can self-organize in zeolite-like structures...
The development of low-cost catalytic systems that mimic the activity of tyrosinase enzymes (Catechol oxidase) is of great promise for future biochemistry technologic demands. Herein, we report the synthesis of new biomolecules systems based on hydra...
The fabrication of molecular gas sieving materials with specific affinities for a single gas species and able to store large quantities of materials at a low or atmospheric pressure is desperately required to reduce the adverse effects of coal and oi...
This paper reports on the production and mechanical properties of Ti6Al4V microlattice structures with strut thickness nearing the single-track width of the laser-based powder bed fusion (LPBF) system used. Besides providing new information on the me...
Thermochemical energy storage is considered as an auspicious method for the recycling of medium-temperature waste heat. The reaction couple Mg(OH)2–MgO is intensely investigated for this purpose, suffering so far from limited cycle stability. T...
Oxygen-depolarized cathodes are a novel concept to be used in chlor-alkali electrolysis in order to generate significant energy savings. In these porous gas diffusion electrodes, hydrophilic and catalytically active microsized silver grains and a hyd...
A new cathode material, FeS2-decorated carbon nanofiber (CNF), is proposed for Li-S batteries. The structure and physicochemical properties of the material have been engineered to enhance the poor cycling stability typically displayed by sulfur compo...
This paper shows the development of a freeze-drying stage for in-situ μ-CT measurements. The stage can operate in a temperature range of −40 °C up to 70 °C, and a pressure range from atmospheric pressure to 7 Pa at the sample holder....
Recently, high entropy oxides (HEO) with special stabilization effects have been widely investigated as new anode materials for lithium-ion batteries. However, the lithium storage mechanism of HEO is still under debate. In this work, we applied a mod...
The dissolution of nano-sized Ni3Al-based γ′ precipitates was investigated in the newly developed polycrystalline nickel-based VDM® Alloy 780 at the surface and in the bulk region with in-situ lab-source and synchrotron X-ray diffract...
We developed an experimental platform for combinative use of an X-ray free electron laser (XFEL) and a high-power nanosecond laser. The main target of the platform is an investigation of matter under high-pressure states produced by a laser-shock com...
The current study focuses on studying the effect of reinforcement of carbon fabric (CF) decorated with in-situ grown silver (Ag) nanoparticles (NPs) on the performance properties of epoxy composite. The Ag NPs were grown on carbon fabric by reducing...
In this study, an MA957 oxide dispersion-strengthened (ODS) alloy was irradiated with high-energy ions in the Argonne Tandem Linac Accelerator System. Fe ions at an energy of 84 MeV bombarded MA957 tensile specimens, creating a damage region ~7.5 μm...
Observation of dynamic testing by means of X-ray computed tomography (CT) and in-situ loading devices has proven its importance in material analysis already, yielding detailed 3D information on the internal structure of the object of interest and its...
The mechanisms responsible for the deformation of nanocrystalline materials are not well understood although many mechanisms have been proposed. This article studies the room-temperature stress-strain relations of bulk nanocrystalline silver deformed...
The use of X-ray radioscopy for in-situ studies of metal foam formation and evolution is reviewed. Selected results demonstrate the power of X-ray radioscopy as diagnostic tool for metal foaming. Qualitative analyses of foam nucleation and evolution,...
of 7