This study aimed to evaluate the depth of cure (DoC) of bulk-fill composite resins, measured by the bottom-to-top Vickers microhardness ratio, using different light-curing units (LCUs): single-wave LED, polywave LED, and halogen. Six bulk-fill compos...
The pursuit of less time-consuming procedures led to the development of high-power light-curing-units (LCU) to light-cure dental-resin-based-materials. This review aims to describe high-power light-emitting-diode (LED)-LCUs, by a bibliometric systema...
The aim of this research was to compare the pulp temperature (PT) rise induced by four light-emitting diode light-curing units (LED LCUs) (Bluephase 20i, Demi Ultra, SPEC 3, and Valo) in different curing modes. Immediately after extraction, the pulp...
Modern dentistry increasingly relies on light-curing units (LCUs) and lasers in essential clinical procedures such as composite resin polymerization, caries treatment, and periodontal therapy. This review aims to outline the evolution of light-emitti...
Purpose: The aim of this in vitro study was to evaluate the influence of different models of commercially available portable dental radiometers on the measurement of light irradiance emitted by light-emitting diode (LED) photocuring units. Materials...
The aim of this in vitro study is to evaluate the effect of resin type and placement technique on the hardness of resin-based composites (RBCs). A total of 300 samples consisting of five RBCs (Filtek Z250 microhybrid, Filtek P60 packable, Tetric Cera...
Background/Objectives: The performance of the adhesive system used for bonding fundamentally influences the success of fixed orthodontic treatment. To withstand masticatory forces and prevent bracket debonding, it is critical to achieve optimal shear...
This study investigated the impact of different light curing units (LCUs) for the polymerization of adhesive system visio.link (VL) on the tensile bond strength (TBS) of different PEEK compositions. For TBS measurements, 216 PEEK specimens with varyi...
This paper reviews the progress of AlGaN-based deep-ultraviolet (DUV) light emitting diodes (LEDs), mainly focusing in the work of the authors’ group. The background to the development of the current device structure on sapphire is described an...
Polymerization of resin-based composites depends on an overlap between photoinitiator absorption and light-curing unit (LCU) emission, yet resins that fail to cure cannot be measured and go unreported. This study tested how photoinitiator chemistry a...
This study aimed to evaluate the effect of two different light-curing units and curing times on the surface microhardness (SMH), compressive strength (CS), and volumetric shrinkage (VS) of four restorative materials (FiltekTM Z250, FiltekTM Bulk Fill...
Ultraviolet light-emitting diode (UV LED) technology offers advantages over conventional UV mercury (UV Hg) lamps, including precise wavelength control, high energy efficiency and rapid curing. While UV LED is widely applied in sectors like dentistry...
Background: Resin composites undergo a certain degree of shrinkage when light-cured with different light sources available on the market, resulting in microleakage of dental restorations. The aim of the present study was to assess microleakage of cla...
Over the last three decades, it has been frequently reported that the properties of dental restorative composites cured with argon laser are similar or superior to those achieved with conventional halogen and light emitting diode (LED) curing units....
The aim of this study was to compare three different light-curing-units (LCUs) and determine their effectiveness in the adhesive cementation of indirect composite restorations when a light-curing resin cement is used. Two resin composites were select...
The aim was to investigate the effects of different post-curing units on the chemical properties (degree of conversion) of 3D-printed resins for producing models in dentistry. The goal is to determine whether less-expensive post-curing units can be a...
This study aimed to assess the light transmittance (T) and temperature increase through different increments of dual-cure bioactive bulk-fill restorative material (ACTIVA), light-cure bulk-fill, and conventional composite resin materials. Cylindrical...
Silicone resin has recently attracted great attention as a high-power Light Emitting Diode (LED) encapsulant material due to its good thermal stability and optical properties. In general, the abrupt curing reaction of the silicone resin for the LED e...
This study aims to investigate the effects of three toughening agents—core–shell rubber particles (CSR), nano-silica particles (NSPs), and epoxidized polybutadiene (EPB)—on the performance of UV-LED-cured epoxy electronic encapsulan...
Wafer-level camera lenses are a very promising process for camera lens fabrication. However, there exist some problems with this technology, such as uneven exposure due to curing non-uniformities. In this study, an optical simulation was implemented...
LED packaging miniaturization has raised more requirements for LED materials. As a material contacting the LED chip directly, the reliability of LED non-conductive adhesive has also garnered increasing attention. This study optimized the formula for...
Photopolymers are an attractive option for large-format additive manufacturing (LFAM), because they can be formulated from structural thermosets and cure rapidly in ambient conditions under low-energy ultraviolet light-emitting diode (UV LED) lamps....
This study evaluated the exposure time of light-curing of the polymers used for cementation on microhardness test in different storage times. The polymers (specifically called resin cements) were RelyX ARC, RelyX U100, and SET. Five specimens of each...
Objective: This systematic review aimed to analyze if polywave light curing units can polymerize Bulk Fill resin composites better than monowave. Materials and methods: Inclusion criteria were in vitro studies that evaluated the polymerization of Bul...
Ultraviolet light emitting diodes (UV-LEDs) have attracted great interest in recent years. They can be used to polymerize coatings, such as those used for prefinished wood flooring. In this project, two lamps were compared for their suitability to be...
Background and Objectives: The objective of this study was (1) to measure the amount of monomers released into the saliva depending on the time elapsed after the hardening of the composite and on the type of monomer used; and (2) with the prolongatio...
The objective of this study was to compare the polymerization kinetics of bulk-fill resin composites cured with a LED-curing device and a diode laser (449 nm). Three bulk-fill composites were light-cured with constant radiation exposure at 10 J/cm2 b...
Resin-based composites (RBCs) have transformed restorative dentistry and its procedures. However, the characteristics of RBCs have been modified over the years to enhance the physical and chemical properties of the materials. This context raises the...
This study aims to examine the effect of additional light curing on the color stability and degree of conversion (DoC) of mono-shade resin composites cured using different light curing units and irradiation levels. Sixty-six disk-shaped samples were...
This study investigated the influence of conventional (10 s at 1160 mW/cm2) and fast high-irradiance (3 s at 2850 mW/cm2) light curing on the micro-tensile bond strength (μTBS) of bulk-fill resin composites bonded to human dentin. Sixty-four extra...
In a high-power white light emitting diode (LED) package, the phosphor/silicone composite is typically used for photometric and colorimetric conversions, ultimately producing the white light. However, the phosphor/silicone composite is always exposed...
Resin-based composites (RBCs) are widely used in restorative dentistry, and their clinical performance depends on the degree of conversion (DC). Light-curing units are used to initiate polymerization, but factors such as the distance between the ligh...
(1) Background: This study investigates the effects of curing light intensity, exposure time, and distance on the Vickers microhardness (VMH), hardness bottom-to-top ratio (HR), and temperature rise (TR) of conventional dental resin-based composite (...
Dental researchers and manufacturers use the ISO 4049 standard to determine the depth of cure (DoC) of resin-based composites (RBCs). This standard uses a 4 mm diameter stainless-steel mold and subsequently divides the length of the remaining hard RB...
Light-emitting diodes (LEDs) are popular as a light source for in vitro plants because they save energy and allow the morphology of the plant to be altered. The purpose of this study was to show that switching from classical fluorescent light (FL) to...
III-nitride-based ultraviolet light emitting diode (UV LED) has numerous attractive applications in air and water purification, UV photolithography, and in situ activation of drugs through optical stimulus, solid state lighting, polymer curing, and l...
With the growing use of high-intensity LED units in orthodontics, the effect of ultra-fast curing protocols on polymerization efficiency remains unclear. This study aimed to evaluate the influence of conventional and rapid high-intensity light curing...
Objectives: To measure and compare the bond strength between three different types of ceramics and resin cement, as well as the degree of conversion of resin cement after using different light-curing units and curing modes. Methods: Three types of ce...
Background and objectives: The light-curing unit is considered an essential piece of equipment in every dental office. This study was conducted to evaluate the effect of Light-Emitting Diodes (LEDs) by the light cure (LC) device on gingival tissues o...
This study investigated the effect of 3 s light-curing with a high-power LED curing unit on the shear bond strength of bulk-fill composites. Four bulk-fill composites were bonded to dentin with a universal adhesive (Scotchbond Universal Plus): two ma...
Optical health monitoring and treatment have been spotlighted due to their biocompatible properties. Several researchers are investigating optical devices for obtaining health signals and curing diseases without any damage to the body. In particular,...
Background: Material-dependent parameters have an important impact on the efficiency of light polymerization. The present in vitro study aimed to investigate the influence of the increment thickness and shade of nano- and nanohybrid resin composites...
The aim of the study was to evaluate the effect of the oxygen-inhibited layer on the bond strength of dental adhesives. The protocol was registered in PROSPERO. PRISMA 2020 guidelines were followed. The focused structured question using Population (P...
(1) Background: To compare the degree of conversion of resin cores in various types of cavities and determine an effective irradiation method for achieving a higher degree of conversion. (2) Methods: Four different-sized cavities (narrow–shallo...
With the advantages offered by cationic photopolymerization (CP) such as broad wavelength activation, tolerance to oxygen, low shrinkage and the possibility of “dark cure”, it has attracted extensive attention in photoresist, deep curing...
Most gelatin hydrogels used in regenerative medicine applications today are fabricated by photocrosslinking due to the convenience and speed of this method. However, in most cases photoinitiators are used, which require UV light, which, in turn, can...
The contribution aims to bring forth a novel synthesis route in developing transparent UV LED-curable coatings accounting for various exposure options. A selection of perfluoropolyether (PFPE)-urethane methacrylate and acrylate resins, free-radical p...
The aim of this in vitro study was to investigate cytotoxic effects of dual-cure bulk-fill resin materials polymerized with a third-generation LED light-curing unit (LCU) on L929 fibroblast cells in terms of morphology and viability. Three novel dual...
How dentists cure a resin-based material has deleterious effects on the material’s properties and its interaction with surrounding dental tissues. Biofilm accumulation has been implicated in the pathogenesis of carious lesions around dental restorati...
Photodynamic therapy (PDT) augments the host antitumor immune response, but the role of the PDT effect on the tumor microenvironment in dependence on the type of photosensitizer and/or therapeutic protocols has not been clearly elucidated. We employe...
of 3