Skip to Content

477 Results Found

  • Article
  • Open Access
7 Citations
5,218 Views
15 Pages

4 February 2025

The Split-Hopkinson pressure bar (SHPB) test is a commonly accepted experiment to investigate the material behavior under high strain rates. Due to the low impedance of soft materials, here, the test has to be performed with plastic bars instead of m...

  • Article
  • Open Access
7 Citations
3,444 Views
16 Pages

On the Development of a Release Mechanism for a Split Hopkinson Tension and Compression Bar

  • Georg Baumann,
  • Dominik Niederkofler,
  • Christian Ellersdorfer and
  • Florian Feist

10 December 2021

Split Hopkinson bars are used for the dynamic mechanical characterisation of materials under high strain rates. Many of these test benches are designed in such a way that they can either be used for compressive or tensile loading. The goal of the pre...

  • Article
  • Open Access
6 Citations
3,734 Views
14 Pages

Development of a True-Biaxial Split Hopkinson Pressure Bar Device and Its Application

  • Shumeng Pang,
  • Weijun Tao,
  • Yingjing Liang,
  • Shi Huan and ,
  • Yijie Liu and
  • Jiangping Chen
  • + 1 author+ 0 author

29 November 2021

Although highly desirable, the experimental technology of the dynamic mechanical properties of materials under multiaxial impact loading is rarely explored. In this study, a true-biaxial split Hopkinson pressure bar device is developed to achieve the...

(This article belongs to the Special Issue Mechanical Metamaterials: Optimization and New Design Ideas)
  • Article
  • Open Access
12 Citations
3,780 Views
19 Pages

An Open-Source Algorithm for Correcting Stress Wave Dispersion in Split-Hopkinson Pressure Bar Experiments

  • Arthur Van Lerberghe,
  • Kin Shing O. Li,
  • Andrew D. Barr and
  • Sam D. Clarke

6 January 2025

Stress wave dispersion can result in the loss or distortion of critical high-frequency data during high-strain-rate material tests or blast loading experiments. The purpose of this work is to demonstrate the benefits of correcting stress wave dispers...

(This article belongs to the Special Issue Advanced Sensing Technologies in Geotechnical Engineering—2nd Edition)
  • Article
  • Open Access
6 Citations
2,618 Views
14 Pages

10 October 2022

The energy-absorption mechanism of nanofluidic systems is being investigated under dynamic cases, represented by the split Hopkinson pressure bar experiment. However, the cost of this cannot be ignored. Therefore, numerical simulation is playing an i...

(This article belongs to the Section Advanced Composites)
  • Article
  • Open Access
28 Citations
4,192 Views
11 Pages

2 April 2020

The effect of using a pulse shaper technique, such as rounding a striker or applying a pulse shaper on the signals recorded with the split Hopkinson pressure bar (SHPB) technique, when the striker and the input bar are in an imperfect position, was i...

(This article belongs to the Section Civil Engineering)
  • Article
  • Open Access
5 Citations
3,057 Views
16 Pages

On the Dynamic Electro-Mechanical Failure Behavior of Automotive High-Voltage Busbars Using a Split Hopkinson Pressure Bar

  • Tobias Werling,
  • Georg Baumann,
  • Florian Feist,
  • Wolfgang Sinz and
  • Christian Ellersdorfer

22 October 2021

High-voltage busbars are important electrical components in today’s electric vehicle battery systems. Mechanical deformations in the event of a vehicle crash could lead to electrical busbar failure and hazardous situations that pose a threat to peopl...

  • Article
  • Open Access
16 Citations
4,501 Views
12 Pages

17 September 2022

Using a split-Hopkinson pressure bar test instrument with a temperature control device, in this work, silicone rubber was tested at different temperatures (−40 °C–200 °C) and different strain rates (1.2 × 103 s−1&ndash...

(This article belongs to the Section Polymer Analysis and Characterization)
  • Article
  • Open Access
1 Citations
1,970 Views
17 Pages

A Dynamic Tensile Method Using a Modified M-Typed Specimen Loaded by Split Hopkinson Pressure Bar

  • Yuan Lin,
  • Jitang Fan,
  • Xinlu Yu,
  • Yingqian Fu and ,
  • Gangyi Zhou,
  • Xu Wang and
  • Xinlong Dong
  • + 2 authors+ 0 author

2 January 2025

Obtaining reliable dynamic mechanical properties through experiments is essential for developing and validating constitutive models in material selection and structural design. This study introduces a dynamic tensile method using a modified M-type sp...

(This article belongs to the Special Issue 3D & 4D Printing in Engineering Applications, 2nd Edition)
  • Article
  • Open Access
12 Citations
5,225 Views
8 Pages

Split Hopkinson Tension Bar and Universal Testing Machine for High-Speed X-ray Imaging of Materials under Tension

  • Puneeth Jakkula,
  • Amitay Cohen,
  • Bratislav Lukić,
  • David Levi-Hevroni and ,
  • Alexander Rack,
  • Georg Ganzenmüller and
  • Stefan Hiermaier
  • + 2 authors+ 0 author

Studying the failure behaviour of engineered or natural materials under dynamic loading scenarios is of high importance, for example to investigate the fracture mechanics and to prevent catastrophic failures of constructions. When dynamic loading is...

  • Article
  • Open Access
17 Citations
4,828 Views
20 Pages

27 March 2021

A dynamic tensile experiment was performed on a rectangular specimen of a non-crimp fabric (NCF) thermoplastic composite T700 carbon/polyamide 6.6 specimens using a split Hopkinson pressure (Kolsky) bar (SHPB). The experiment successfully provided us...

(This article belongs to the Section Advanced Composites)
  • Article
  • Open Access
16 Citations
3,809 Views
16 Pages

Investigation of Mixed-Mode I/II Fracture under Impact Loading Using Split-Hopkinson Pressure Bar

  • Fei Wang,
  • Zheming Zhu,
  • Meng Wang,
  • Hao Qiu and ,
  • Lei Zhou,
  • Ruifeng Liu and
  • Peng Ying
  • + 2 authors+ 0 author

14 October 2020

Mixed-mode fracture of construction building materials under impact loading is quite common in civil engineering. The investigation of mixed-mode crack propagation behavior is an essential work for fundamental research and engineering application. A...

(This article belongs to the Section Civil Engineering)
  • Article
  • Open Access
10 Citations
3,896 Views
26 Pages

26 September 2020

The dynamic behavior of the lithium-ion battery is evaluated by simulating the full battery system and each corresponding component, including the jellyroll and thin-foil electrodes. The thin-foil electrodes were evaluated using a novel design of spl...

(This article belongs to the Special Issue Crash Safety of Lithium-Ion Batteries)
  • Article
  • Open Access
22 Citations
5,073 Views
25 Pages

16 July 2019

Fiber-reinforced polymer (FRP) has become increasingly popular in repairing existing steel-reinforced concrete (RC) members or constructing new structures. Although the quasi-static axial compression performance of FRP-confined concrete (FCC) has bee...

(This article belongs to the Special Issue Structural Performances of Concrete Composite Members: Experimental, Theoretical, Numerical Approaches)
  • Article
  • Open Access
13 Citations
3,419 Views
16 Pages

21 November 2022

The dynamic fracture process of rock materials is of importance for several industrial applications, such as drilling for geothermal installation. Numerical simulation can aid in increasing the understanding about rock fracture; however, it requires...

(This article belongs to the Section Advanced Materials Characterization)
  • Article
  • Open Access
23 Citations
4,321 Views
19 Pages

Dynamic Behavior of Aluminum Alloy Aw 5005 Undergoing Interfacial Friction and Specimen Configuration in Split Hopkinson Pressure Bar System at High Strain Rates and Temperatures

  • Amine Bendarma,
  • Tomasz Jankowiak,
  • Alexis Rusinek,
  • Tomasz Lodygowski and ,
  • Bin Jia,
  • María Henar Miguélez and
  • Maciej Klosak
  • + 2 authors+ 0 author

16 October 2020

In this paper, experimental and numerical results of an aluminum alloy’s mechanical behavior are discussed. Over a wide range of strain rates (10−4 s−1 ≤ έ ≤ 103 s−1) the influence of the loading impact, velocity and tem...

(This article belongs to the Section Metals and Alloys)
  • Feature Paper
  • Article
  • Open Access
3 Citations
2,753 Views
21 Pages

24 June 2022

In the presented research, a split Hopkinson tension bar (SHTB) was used to measure the mechanical response of multi-material single-lap joints in the high-rate loading regime. High-performance applications require high-quality measurements of the me...

(This article belongs to the Special Issue Hybrid Metal-Polymer Joints)
  • Article
  • Open Access
11 Citations
3,532 Views
15 Pages

28 October 2020

To reveal the stress transfer mechanism of the flange in a split Hopkinson tension bar, explicit finite element analyses of the impact of the hollow striker on the flange were performed across a range of flange lengths. The tensile stress profiles mo...

(This article belongs to the Section Mechanical Engineering)
  • Article
  • Open Access
12 Citations
3,273 Views
14 Pages

22 April 2022

Young’s modulus is a key parameter of materials. The method of its calculation in the current paper is concerned with the mismatch of the mechanical impedance at the bar/specimen interface for a compression SHPB (split Hopkinson pressure bar) t...

(This article belongs to the Topic Processing, Analysis, Modelling and Mechanics of Materials and Structures)
  • Article
  • Open Access
8 Citations
5,335 Views
14 Pages

Fracture Analysis of Ultrahigh-Strength Steel Based on Split Hopkinson Pressure Bar Test

  • Shihong Xiao,
  • Xiaosheng Luan,
  • Zhiqiang Liang,
  • Xibin Wang and ,
  • Tianfeng Zhou and
  • Yue Ding
  • + 1 author+ 0 author

6 April 2022

Impact loading is an important cause of fracture failure of ultrahigh-strength steel parts during service. Revealing the fracture mechanism of ultrahigh-strength steel under impact loading has important reference significance for the material prepara...

(This article belongs to the Special Issue Advances in High-Strength Low-Alloy Steels)
  • Article
  • Open Access
12 Citations
2,833 Views
20 Pages

High Strain Rate Response of Sandstones with Different Porosity under Dynamic Loading Using Split Hopkinson Pressure Bar (SHPB)

  • Grzegorz Stopka,
  • Roman Gieleta,
  • Robert Panowicz,
  • Daniel Wałach and
  • Grzegorz Piotr Kaczmarczyk

20 June 2024

This article presents the results of dynamic tests of sandstone samples differing in strength parameters and porosity, which were carried out with the use of the split Hopkinson pressure bar (SHPB). For this study, three types of sandstones were cons...

(This article belongs to the Section Materials Science and Engineering)
  • Article
  • Open Access
6 Citations
3,960 Views
15 Pages

22 October 2021

In this study, a total of 30 3D re-entrant honeycomb specimens made of polyamide were fabricated with various configurations by using the additive manufacturing (AM) technique. Split Hopkinson Pressure Bar (SHPB) tests were conducted on the RH specim...

(This article belongs to the Special Issue Vehicle Crashworthiness and Lightweight Design)
  • Article
  • Open Access
4 Citations
1,931 Views
17 Pages

25 January 2025

In recent years, a kind of novel cellular concrete, fabricated by spherical saturated superabsorbent polymers, was developed. Its compressive behavior under high strain rate loadings has been studied by split Hopkinson pressure bar equipment in previ...

(This article belongs to the Special Issue Recycling and Development of New Building Materials or Products (Second Volume))
  • Article
  • Open Access
24 Citations
3,767 Views
15 Pages

Research on Dynamic Strength and Inertia Effect of Concrete Materials Based on Large-Diameter Split Hopkinson Pressure Bar Test

  • Bi Sun,
  • Rui Chen,
  • Yang Ping,
  • ZhenDe Zhu and ,
  • Nan Wu and
  • Zhenyue Shi
  • + 1 author+ 0 author

20 April 2022

The Split Hopkinson Pressure Bar (SHPB) test device is an important tool to study the dynamic characteristics of concrete materials. Inertial effect is one of the main factors that cause inaccurate results in SHPB tests of concrete materials. To solv...

(This article belongs to the Special Issue Mechanical Behavior of Concrete Materials and Structures: Experimental Evidence and Analytical Models)
  • Article
  • Open Access
4 Citations
2,081 Views
17 Pages

15 December 2023

The laminated metal materials are widely used in military, automobile and aerospace industries, but their dynamic response mechanical behavior needs to be further clarified, especially for materials with joint interface paralleling to the loading dir...

(This article belongs to the Special Issue Innovative Material Design and Nondestructive Testing Applications for Infrastructure Materials)
  • Article
  • Open Access
10 Citations
3,712 Views
17 Pages

Investigation on Dynamic Mechanical Properties of Recycled Concrete Aggregate under Split-Hopkinson Pressure Bar Impact Test

  • Wenping Du,
  • Caiqian Yang,
  • Hans De Backer,
  • Chen Li and ,
  • Kai Ming,
  • Honglei Zhang and
  • Yong Pan
  • + 2 authors+ 0 author

The dynamic mechanical properties of recycled concrete (RC) and natural concrete (NC) were studied by impact tests and numerical simulation. The quasi-static tests were conducted by a servo-hydraulic machine, while the impact test used a 50 mm diamet...

(This article belongs to the Special Issue Sustainable Development: Recycle and Reuse of Waste Materials in Construction Industry)
  • Data Descriptor
  • Open Access
3 Citations
3,834 Views
17 Pages

1 March 2023

Bar impact instruments, such as the (split) Hopkinson bars and direct impact Hopkinson bars, measure blast/impact waves or mechanical properties of materials at high strain rates. To effectively use such instruments, it is essential to know (i) the e...

  • Article
  • Open Access
12 Citations
3,276 Views
19 Pages

12 October 2020

The ductile behavior of strain-hardening cement-based composites (SHCC) under direct tensile load makes them promising solutions in applications where high energy dissipation is needed, such as in earthquakes, impacts by projectiles, or blasts. Howev...

(This article belongs to the Special Issue Mineral-Bonded Composites for Enhanced Structural Impact Safety)
  • Data Descriptor
  • Open Access
8 Citations
5,766 Views
18 Pages

28 April 2022

This manual presents a procedure to calibrate the one-dimensional sound speed (co) and Poisson’s ratio (ν) of a (split) Hopkinson bar using the open-source templates written in Excel® and Matlab® for dispersion correction. The Excel&...

  • Article
  • Open Access
2 Citations
1,489 Views
16 Pages

1 August 2024

The split-Hopkinson pressure bar technique is widely used to determine the dynamic mechanical behavior of materials. However, spike-like stress features appear in the initial stress behavior of ultra-soft materials tested with a split-Hopkinson bar....

(This article belongs to the Section Materials Physics)
  • Article
  • Open Access
9 Citations
6,130 Views
22 Pages

11 January 2023

The split Hopkinson pressure bars (SHPB) system is the most commonly employed machine to study the dynamic characteristics of different materials under high strain rates. In this research, a numerical investigation is carried out to study different b...

(This article belongs to the Special Issue Lightweight Composites Materials: Sustainability and Applications)
  • Article
  • Open Access
11 Citations
3,303 Views
15 Pages

Mechanical Response and Failure Mechanisms of Natural Bamboo Fiber Reinforced Poly-Benzoxazine Composite Subjected to Split-Hopkinson Tensile Bar Loading

  • Kai Zhang,
  • Fangxin Wang,
  • Bin Yang,
  • Lin Li and ,
  • Li Gao,
  • Yongyang Sun and
  • Fuzheng Guo
  • + 2 authors+ 0 author

2 April 2022

In this study, chopped natural bamboo fibers were successfully added in the benzoxazine matrix by the hot-pressing method to fabricate environmentally friendly bio-composite. The mechanical behaviors and failure mechanisms of neat benzoxazine matrix...

(This article belongs to the Section Polymer Composites and Nanocomposites)
  • Article
  • Open Access
3 Citations
2,552 Views
15 Pages

27 November 2023

The split Hopkinson pressure bar (SHPB) is a machine used for obtaining dynamic material properties at high strain rates of 102–104 s−1. In the SHPB test, the material properties obtained vary depending on the shape of the specimen. In ot...

  • Article
  • Open Access
14 Citations
4,349 Views
16 Pages

1 January 2020

Polymer matrix composites (PMC), despite their many advantages, have limited use at elevated temperatures. To expand the scope of their uses, it becomes necessary to use thermal barrier coatings (TBC). In addition to elevated temperatures, composite...

(This article belongs to the Special Issue Advances in Fiber-Reinforced Polymer Composites)
  • Article
  • Open Access
3 Citations
2,710 Views
20 Pages

Numerical Design of a Thread-Optimized Gripping System for Lap Joint Testing in a Split Hopkinson Apparatus

  • Bernardo S. Moreira,
  • Paulo D. P. Nunes,
  • Carlos M. da Silva,
  • António Francisco G. Tenreiro and ,
  • António M. Lopes,
  • Ricardo J. C. Carbas,
  • Eduardo A. S. Marques,
  • Marco P. L. Parente and
  • Lucas F. M. da Silva
  • + 4 authors+ 0 author

17 February 2023

Currently, few experimental methods exist that enable the mechanical characterization of adhesives under high strain rates. One such method is the Split Hopkinson Bar (SHB) test. The mechanical characterization of adhesives is performed using differe...

(This article belongs to the Section Physical Sensors)
  • Article
  • Open Access
10 Citations
5,010 Views
22 Pages

2 March 2022

Numerical models can be useful for analysis of the ability of structural engineering materials to withstand harsh environmental conditions such as dynamic loading. In the present study, a microstructure-variable-based numerical model for predicting t...

  • Proceeding Paper
  • Open Access
3 Citations
3,004 Views
10 Pages

An experimental and numerical study on three flat specimen geometries for characterization of the dynamic shear behavior of metals with the use of the compression Split Hopkinson Pressure Bar (SHPB) technique is presented in the paper. The aim of the...

(This article belongs to the Proceedings of The 19th International Conference on Experimental Mechanics)
  • Article
  • Open Access
72 Citations
9,500 Views
15 Pages

Dynamic Splitting Performance and Energy Dissipation of Fiber-Reinforced Concrete under Impact Loading

  • Dashun Cui,
  • Limin Wang,
  • Chunwei Zhang,
  • Huiting Xue and ,
  • Dianwei Gao and
  • Fanxiu Chen
  • + 1 author+ 0 author

14 January 2024

In this paper, the influence of different fiber materials on the dynamic splitting mechanical properties of concrete was investigated. Brazil disc dynamic splitting tests were conducted on plain concrete, palm fiber-reinforced concrete, and steel fib...

  • Article
  • Open Access
7 Citations
3,442 Views
13 Pages

4 January 2021

The Split-Hopkinson pressure bar (SHPB), which is used for acquiring material properties at high strain rates (102–104 s−1), requires proper specimen size selection. Under the same applied pressure, an increased S-S curve is obtained as t...

  • Article
  • Open Access
3 Citations
2,969 Views
13 Pages

Experimental Investigation of Unidirectional Glass-Fiber-Reinforced Plastics under High Strain Rates

  • Sören Bieler,
  • Sebastian Haller,
  • Robert Brandt and
  • Kerstin Weinberg

26 October 2023

When a vehicle leaves the road, crash barriers stop it and prevent significant damage to the vehicle, its environment, and the occupants. Typically, such protection systems are made of simple steel, but fiber-reinforced composites can efficiently abs...

(This article belongs to the Special Issue Early Career Scientists’ (ECS) Contributions to Applied Mechanics)
  • Article
  • Open Access
16 Citations
2,948 Views
17 Pages

Study on Damage Characteristics and Failure Modes of Gypsum Rock under Dynamic Impact Load

  • Yongxiang Ge,
  • Gaofeng Ren,
  • Congrui Zhang,
  • Yihu Shi and
  • Luwei Zhang

13 May 2023

The objective of this work was to investigate the damage characteristics and failure modes of gypsum rock under dynamic impact loading. Split Hopkinson pressure bar (SHPB) tests were performed under different strain rates. The strain rate effects on...

  • Article
  • Open Access
3 Citations
3,449 Views
14 Pages

Dynamic and Static Strength Analysis of 5056 Aluminum Alloy Fabricated by Wire-Arc Additive Manufacturing

  • Alexey Evstifeev,
  • Aydar Mavlyutov,
  • Darya Volosevich,
  • Marina Gushchina and ,
  • Olga Klimova-Korsmik,
  • Konstantin Nasonovskiy and
  • Sofya Shabunina
  • + 2 authors+ 0 author

12 February 2025

This article presents the results of experimental studies on the dynamic and static strength of commercial aluminum alloy 5056 manufactured by wire-arc additive manufacturing (WAAM). The main objective is to evaluate the utilization potential of this...

  • Article
  • Open Access
16 Citations
2,882 Views
26 Pages

Experimental Investigation of the Dynamic Mechanical Properties of Polypropylene-Fiber-Reinforced Foamed Concrete at High Temperatures

  • Longyang Chen,
  • Penghui Li,
  • Weiguo Guo,
  • Ruifeng Wang and ,
  • Dongjian Zhang,
  • Meng Gao and
  • Chang Peng
  • + 2 authors+ 0 author

31 May 2023

Polypropylene-fiber-reinforced foamed concrete (PPFRFC) is often used to reduce building structure weight and develop engineering material arresting systems (EMASs). This paper investigates the dynamic mechanical properties of PPFRFC with densities o...

(This article belongs to the Section Polymer Composites and Nanocomposites)
  • Article
  • Open Access
35 Citations
3,759 Views
13 Pages

19 May 2021

As mining depth increases, the backfill mining method is more and more widely used in underground mines. The dynamic load generated by the blasting can affect the stability of the cemented tailings backfill (CTB). The CTB samples were prepared to con...

(This article belongs to the Special Issue Backfilling Materials for Underground Mining, Volume II)
  • Article
  • Open Access
959 Views
26 Pages

Quasi-Static and High Strain-Rate Behavior of Carbon Fiber Reinforced Modified BOFS Concrete

  • Yeou-Fong Li,
  • Chun-Wei Chien,
  • Jin-Yuan Syu,
  • Chih-Hong Huang and ,
  • Wen-Shyong Kuo and
  • Ying-Kuan Tsai
  • + 1 author+ 0 author

27 September 2025

This study examines the mechanical properties of concrete in which natural aggregates are entirely replaced by modified basic oxygen furnace slag (MBOFS) and reinforced with chopped carbon fibers, under both dynamic and quasi-static loading condition...

(This article belongs to the Special Issue Fiber-Reinforced Polymer (FRP) and Composites for Structural Engineering)
  • Article
  • Open Access
26 Citations
5,073 Views
18 Pages

27 February 2022

Honeycomb aluminum structures are used in energy-absorbing constructions in military, automotive, aerospace and space industries. Especially, the protection against explosives in military vehicles is very important. The paper deals with the study of...

(This article belongs to the Topic Processing, Analysis, Modelling and Mechanics of Materials and Structures)
  • Article
  • Open Access
16 Citations
2,814 Views
14 Pages

27 April 2021

This study focuses on the dynamic compression performance of corroded steel fiber-reinforced concrete (SFRC) exposed to drying–wetting chloride cycles by a 37 mm diameter split Hopkinson pressure bar (SHPB) system. Three steel fiber contents (0.5%, 1...

(This article belongs to the Special Issue Sustainable, Self-Healing, and Functional Building Materials)
  • Article
  • Open Access
10 Citations
3,460 Views
11 Pages

Surface Interactions of Transonic Shock Waves with Graphene-Like Nanoribbons

  • Shamal L. Chinke,
  • Inderpal Singh Sandhu,
  • Tejashree M. Bhave and
  • Prashant S. Alegaonkar

17 September 2020

Graphene-like nanoribbons (GLNRs) were fabricated (length—20 μm; width—2 μm) and subjected to blast-like pulsed pressure >1.5 GPa (pulse speed ≈1 Mach, impulse duration, ≈µs) to examine the amount of absorption....

  • Article
  • Open Access
26 Citations
5,462 Views
19 Pages

5 January 2018

To study the dynamic shear deformation and failure properties of Ti-6Al-4V (Ti-64) alloy and Ti-5Al-5Mo-5V-1Cr-1Fe (Ti-55511) alloy, a series of forced shear tests on flat hat shaped (FHS) specimens for the two investigated materials was performed us...

of 10