Investigation on Dynamical Mechanics, Energy Dissipation, and Microstructural Characteristics of Cemented Tailings Backfill under SHPB Tests

As mining depth increases, the backfill mining method is more and more widely used in underground mines. The dynamic load generated by the blasting can affect the stability of the cemented tailings backfill (CTB). The CTB samples were prepared to conduct a test of the split Hopkinson pressure bar (SHPB) to investigate the dynamic disturbance of CTB. The present paper discusses dynamical mechanics, energy dissipation, and microstructure analysis of CTB. Microcomputer tomography (micro-CT) scanning of CTB samples after the SHPB test was performed to analyze the evolution of internal cracks. The experimental results showed that when the average strain rate (ASR) increased from 30 to 98 s−1, the dynamic uniaxial compression strength (DUCS) of the CTB showed a trend of first increasing and decreasing with the increase in ASR. The dynamic stress–strain pre-peak curve of CTB directly enters the linear elastic stage. As ASR increases, the absorbed energy of the CTB shows a trend of first increasing and then decreasing. Moreover, according to the micro-CT scanning results, the crack area of CTB accounts for about 16% of the sample near the incident bar and about 1% near the transmitted bar. The crack area ratio is exponentially related to the specimen height. These findings can provide reasonable dynamical CTB strength data selection for underground pillar mining.


Introduction
Underground metal mines have made a steady transition to deep mining as time goes on. Many metal mining methods are available such as caving, open stoping, and filling methods for excavating ore reserves from underground. Among the many methods employed, the filling mining method has been widely used because of its advantages, such as a small stripping ratio, low loss rate, reduced solid waste accumulation, and prevention of surface settlement. Therefore, the mechanical properties of the cemented backfill are very important in ensuring the safety of mining [1,2]. In recent years, the instability accidents of backfills have been mostly caused by blasting vibrations in nearby mining areas. Jiang et al. [3] studied dynamic mechanisms of layered cemented backfill pillars under the far-field blasting and found that the peak values of the velocity and the displacement response of the backfilling body are affected by the frequency of stress waves. In this scenario, the cemented tailings backfill (CTB) or cemented paste backfill (CPB) in goaf is disturbed by the impact load generated during the blasting of the mining adjacent stope, which affects the stability of the CTB.
for the backfill mining method, the same size of the mining chamber and prop are used in mines. Therefore, in this paper, the size of the specimen used in the SHPB test is 50 mm in diameter × 50 mm in height, closer to the typical mine site. The paper introduces new ideas to study the strengthening effect of the strain rate of cemented backfill under SHPB and analyze the stress-strain curve. The micro-CT reveals the internal micro-crack law of CTB under SHPB, thus providing a useful reference for improving the stability of CTB in the pillar mine.

Material Characterization
The tested unclassified gold tailings used in the study were from a gold mine in the Shandong Gold Group Co., Ltd. The density of the tested tailings was 2.34 g/cm 3 , and the specific surface area was 39.595 m 3 /kg. After drying, the tailings were analyzed by a laser particle size analyzer. Figure 1 shows the particle size distribution curve of unclassified tailing. The d50 of unclassified tailing is 321.295 µm, which belongs to largersized tailings according to Landriault's mine tailings classification [30,31]. A sequential X-ray fluorescence spectrometer is used to test the chemical composition of tested tailings and cement. Table 1 shows the chemical composition of the tested tailings. The main component is SiO 2 , accounting for 58.4 wt.%. Figure 2 shows the X-ray diffraction (XRD) patterns of tested tailings, which agrees well with their chemical components [32]. The tailings mainly consist of crystalline minerals (i.e., quartz and lime).

Specimen Preparation
In this study, the value of solid content and the cement-tailings ratio of the manufactured CTB samples was constantly set to 75 wt.% and 0.25. The experiment personnel used a standard electronic scale to weigh the tailings, cement, and tap water and fully stirred the materials in the mixer for 180 s [33]. The content of each component is 34.5g of cement, 138 g of tailings, and 57.5 g of water. The slump value of the tested CTB slurry was about 24.5 cm. Then, the stirred slurry was poured into the mold (the mold with a height of 50 mm and a diameter of 50 mm) with the requirements of ASTM C192/C192M [34]. The CTB samples were placed inside the standard curing box at 20 ℃ ± 1 ℃ in temperature, 90% ± 1% in humidity. After 48 h, the samples were demolished from the mold and then returned to the curing box until 28 d [35]. After 28 d, the specimen was gently polished at both ends to meet the flatness requirements of the dynamic load test [36]. The preparation process of CTB specimens is shown in Figure 3. The ordinary Portland cement 42.5R was used to be the cementing material. The chemical composition is shown in Table 2. Among them, the effective ingredient CaO accounts for 35.4 wt.%.
The water used is tap water.

Specimen Preparation
In this study, the value of solid content and the cement-tailings ratio of the manufactured CTB samples was constantly set to 75 wt.% and 0.25. The experiment personnel used a standard electronic scale to weigh the tailings, cement, and tap water and fully stirred the materials in the mixer for 180 s [33]. The content of each component is 34.5 g of cement, 138 g of tailings, and 57.5 g of water. The slump value of the tested CTB slurry was about 24.5 cm. Then, the stirred slurry was poured into the mold (the mold with a height of 50 mm and a diameter of 50 mm) with the requirements of ASTM C192/C192M [34]. The CTB samples were placed inside the standard curing box at 20°C ± 1°C in temperature, 90% ± 1% in humidity. After 48 h, the samples were demolished from the mold and then returned to the curing box until 28 d [35]. After 28 d, the specimen was gently polished at both ends to meet the flatness requirements of the dynamic load test [36]. The preparation process of CTB specimens is shown in Figure 3.

Experimental Devices
The SHPB test platform consisted of a nitrogen cylinder, Hopkinson pressure bar test bench, launch chamber, elastic pressure bar, confining pressure device, super dynamic strain gauge, oscilloscope, computer, timer, and other parts. The diameter of the pressure bar in the SHPB test device was 50 mm, the material was 40 Cr alloy steel, the density was 7800 kg/m 3 , and the wave velocity was 5200 m/s. In this study, the maximum average strain rate was 98 s −1 . Besides, the sensitivity of the hyper dynamic strain gauge was more than 0.2V/100 με, and the strain coefficient was 2.0 [37]. Figure 4 is a schematic diagram of the SHPB test device system. Before the beginning of SHPB, a thin layer of Vaseline should be coated on the end surfaces of the specimen to eliminate possible stress that is uneven due to contact between the specimen and bars. The micro-CT test system used in this study was a dual-source, dual-detector system. The two sources are the 225 kV microfocus and 450 kV light source, whereas the two detectors were a flat panel and line array detector. In this experiment, a 225 kV micro-focus micro-CT light source was used for a continuous rotating scan at a spatial distribution rate

Experimental Devices
The SHPB test platform consisted of a nitrogen cylinder, Hopkinson pressure bar test bench, launch chamber, elastic pressure bar, confining pressure device, super dynamic strain gauge, oscilloscope, computer, timer, and other parts. The diameter of the pressure bar in the SHPB test device was 50 mm, the material was 40 Cr alloy steel, the density was 7800 kg/m 3 , and the wave velocity was 5200 m/s. In this study, the maximum average strain rate was 98 s −1 . Besides, the sensitivity of the hyper dynamic strain gauge was more than 0.2 V/100 µε, and the strain coefficient was 2.0 [37]. Figure 4 is a schematic diagram of the SHPB test device system. Before the beginning of SHPB, a thin layer of Vaseline should be coated on the end surfaces of the specimen to eliminate possible stress that is uneven due to contact between the specimen and bars.

Experimental Devices
The SHPB test platform consisted of a nitrogen cylinder, Hopkinson pressure bar test bench, launch chamber, elastic pressure bar, confining pressure device, super dynamic strain gauge, oscilloscope, computer, timer, and other parts. The diameter of the pressure bar in the SHPB test device was 50 mm, the material was 40 Cr alloy steel, the density was 7800 kg/m 3 , and the wave velocity was 5200 m/s. In this study, the maximum average strain rate was 98 s −1 . Besides, the sensitivity of the hyper dynamic strain gauge was more than 0.2V/100 με, and the strain coefficient was 2.0 [37]. Figure 4 is a schematic diagram of the SHPB test device system. Before the beginning of SHPB, a thin layer of Vaseline should be coated on the end surfaces of the specimen to eliminate possible stress that is uneven due to contact between the specimen and bars. The micro-CT test system used in this study was a dual-source, dual-detector system. The two sources are the 225 kV microfocus and 450 kV light source, whereas the two detectors were a flat panel and line array detector. In this experiment, a 225 kV micro-focus micro-CT light source was used for a continuous rotating scan at a spatial distribution rate The micro-CT test system used in this study was a dual-source, dual-detector system. The two sources are the 225 kV microfocus and 450 kV light source, whereas the two detectors were a flat panel and line array detector. In this experiment, a 225 kV micro-focus micro-CT light source was used for a continuous rotating scan at a spatial distribution rate of 23 Lp/mm. The exact resolution of the backfill specimen prepared in the experiment was 68 µm. Figure 5 presents a diagram of the CT test system device.
Minerals 2021, 11, x FOR PEER REVIEW 6 of 13 of 23 Lp/mm. The exact resolution of the backfill specimen prepared in the experiment was 68 μm. Figure 5 presents a diagram of the CT test system device.

Figure 5.
Diagram of micro-CT test system device.

Dynamic Stress Equilibrium
The assumption condition for establishing the SHPB test system is that it conforms to the one-dimensional stress wave propagation theory and that the two ends of the specimen reach stress equilibrium [38]. Therefore, it is necessary to check the stress equilibrium at both ends of the specimen. When the incident wave plus the reflected wave is approximately equal to the transmitted wave, the two ends of the specimen are said to reach a stressed equilibrium. Figure 6 is a superposition of the waveform relationship of the CTB specimen. The stress at the incident end of the specimen is counted by the incident wave plus the reflected wave, and the stress at the transmitted end is the transmitted wave. The relationship between the stress and time in the pressure bars at both ends of the specimen can be obtained by superposition. As shown in Figure 6, the amplitudes of superimposed wave and transmitted wave are almost equal. The waveforms overlap, indicating that the two ends of the backfill specimen in this experiment have reached a stressed equilibrium.

Dynamic Stress Equilibrium
The assumption condition for establishing the SHPB test system is that it conforms to the one-dimensional stress wave propagation theory and that the two ends of the specimen reach stress equilibrium [38]. Therefore, it is necessary to check the stress equilibrium at both ends of the specimen. When the incident wave plus the reflected wave is approximately equal to the transmitted wave, the two ends of the specimen are said to reach a stressed equilibrium. Figure 6 is a superposition of the waveform relationship of the CTB specimen. The stress at the incident end of the specimen is counted by the incident wave plus the reflected wave, and the stress at the transmitted end is the transmitted wave. The relationship between the stress and time in the pressure bars at both ends of the specimen can be obtained by superposition. As shown in Figure 6, the amplitudes of superimposed wave and transmitted wave are almost equal. The waveforms overlap, indicating that the two ends of the backfill specimen in this experiment have reached a stressed equilibrium.
Minerals 2021, 11, x FOR PEER REVIEW 6 of 13 of 23 Lp/mm. The exact resolution of the backfill specimen prepared in the experiment was 68 μm. Figure 5 presents a diagram of the CT test system device.

Figure 5.
Diagram of micro-CT test system device.

Dynamic Stress Equilibrium
The assumption condition for establishing the SHPB test system is that it conforms to the one-dimensional stress wave propagation theory and that the two ends of the specimen reach stress equilibrium [38]. Therefore, it is necessary to check the stress equilibrium at both ends of the specimen. When the incident wave plus the reflected wave is approximately equal to the transmitted wave, the two ends of the specimen are said to reach a stressed equilibrium. Figure 6 is a superposition of the waveform relationship of the CTB specimen. The stress at the incident end of the specimen is counted by the incident wave plus the reflected wave, and the stress at the transmitted end is the transmitted wave. The relationship between the stress and time in the pressure bars at both ends of the specimen can be obtained by superposition. As shown in Figure 6, the amplitudes of superimposed wave and transmitted wave are almost equal. The waveforms overlap, indicating that the two ends of the backfill specimen in this experiment have reached a stressed equilibrium.

Relation between Dynamic Stress and Strain
Actually, the dynamical strength enhancement factor obtained in this manuscript could provide a data basis for the engineering application of the strength design of the backfill. As we know, the design of the CTB must consider the safety factor in the actual mining process. CTB samples were performed ASR by SHPB of ASR in the range from 30 to 98 s −1 . Figure 6 shows the relationship between the ASR of CTB and DUCS and the dynamic strength enhancement factor. As shown in Figure 6, when the ASR was between 30 and 98 s −1 , the DUCS of CTB shows a trend of first increasing and then decreasing with ASR. When the strain rate is 74 s −1 , the peak DUCS of CTB is 14.1 MPa. According to the uniaxial compression test, the static uniaxial compressive strength of CTB is 4.47 MPa. In rock dynamics, dynamic strength enhancement factors are often used further to express the strain rate effect [39].
In the equation, K is the dynamic strength enhancement factor, σ d is the peak compressive strength under dynamic load, and σ S is the peak compressive strength under static load. The calculation results are shown in Figure 7.

Relation between Dynamic Stress and Strain
Actually, the dynamical strength enhancement factor obtained in this manuscript could provide a data basis for the engineering application of the strength design of the backfill. As we know, the design of the CTB must consider the safety factor in the actual mining process. CTB samples were performed ASR by SHPB of ASR in the range from 30 to 98 s −1 . Figure 6 shows the relationship between the ASR of CTB and DUCS and the dynamic strength enhancement factor. As shown in Figure 6, when the ASR was between 30 and 98 s −1 , the DUCS of CTB shows a trend of first increasing and then decreasing with ASR. When the strain rate is 74 s −1 , the peak DUCS of CTB is 14.1 MPa. According to the uniaxial compression test, the static uniaxial compressive strength of CTB is 4.47 MPa. In rock dynamics, dynamic strength enhancement factors are often used further to express the strain rate effect [39].    Figure 7 and Figure 8, CTB also exhibits a strengthening effect of ASR, consistent with the findings of other scholars [13,16]. However, the difference is that when the ASR is 74 s −1 , the strengthening effect of the strain rate decreases. The large wave impedance of CTB may cause this. The height to diameter ratio of the specimen used here is 1, and the height to diameter ratio of the backfill specimen studied by most scholars is 0.5. Hence, when the strain rate is greater than 74 s −1 , the strengthening effect of the strain rate decreases.
In this study, the pre-peak mechanical properties of CTB were significantly investigated. The paper also analyzes the pre-peak stress-strain curve of CTB with the ASR of 74 s −1 . The stress-strain curve at the OB section is nearly straight. Due to the immediate impact speed, the pore compaction stage of the specimen does not appear, and the stressstrain curve directly enters the elastic deformation stage. When the BC section is at the  Figure 8 shows that the relationship between the stress and strain curves of the CTB under different ASR. As shown in Figures 7 and 8, CTB also exhibits a strengthening effect of ASR, consistent with the findings of other scholars [13,16]. However, the difference is that when the ASR is 74 s −1 , the strengthening effect of the strain rate decreases. The large wave impedance of CTB may cause this. The height to diameter ratio of the specimen used here is 1, and the height to diameter ratio of the backfill specimen studied by most scholars is 0.5. Hence, when the strain rate is greater than 74 s −1 , the strengthening effect of the strain rate decreases. stage in which the micro-fracture development is stable, the specimen presents microfracture and develops steadily, although the stress-strain curve is still almost linear at this point. When the BC section is at the progressive rupture stage, the micro-rupture continues to accumulate and develop until the specimen is completely damaged and reaches the compressive strength of the cemented backfill at the dynamic peak, that is, point C.

Energy Dissipation Analysis
The SHPB test was conducted along with the energy dissipation, and the absorbed energy was used for evaluation. The relationships among incident energy I W , reflected energy R W , transmitted energy T W , and absorbed energy S W are given by [39], where E is the elastic modulus of the compression bar, A is the cross-sectional area of the incident bar, 0 C is the velocity of elastic stress wave, I ε is the incident strain, R ε is the reflected strain, and T ε is the transmitted strain. According to the test results. The CTB energy is obtained as shown in Table 3. Next, the relationship diagram among strain rate and incident energy reflected energy, transmitted energy, and absorbed energy is drawn according to Table 3. It can be In this study, the pre-peak mechanical properties of CTB were significantly investigated. The paper also analyzes the pre-peak stress-strain curve of CTB with the ASR of 74 s −1 . The stress-strain curve at the OB section is nearly straight. Due to the immediate impact speed, the pore compaction stage of the specimen does not appear, and the stress-strain curve directly enters the elastic deformation stage. When the BC section is at the stage in which the micro-fracture development is stable, the specimen presents microfracture and develops steadily, although the stress-strain curve is still almost linear at this point. When the BC section is at the progressive rupture stage, the micro-rupture continues to accumulate and develop until the specimen is completely damaged and reaches the compressive strength of the cemented backfill at the dynamic peak, that is, point C.

Energy Dissipation Analysis
The SHPB test was conducted along with the energy dissipation, and the absorbed energy was used for evaluation. The relationships among incident energy W I , reflected energy W R , transmitted energy W T , and absorbed energy W S are given by [39], where E is the elastic modulus of the compression bar, A is the cross-sectional area of the incident bar, C 0 is the velocity of elastic stress wave, ε I is the incident strain, ε R is the reflected strain, and ε T is the transmitted strain. According to the test results. The CTB energy is obtained as shown in Table 3. Next, the relationship diagram among strain rate and incident energy reflected energy, transmitted energy, and absorbed energy is drawn according to Table 3. It can be seen from Figure 9 that the incident energy of the cemented backfill and the reflected energy both increase as the strain rate increases. As the strain rate increases, the transmitted energy first decreases and then increases. However, transmitted energy is less than 1 J due to the large difference between the density of the cemented backfill and the density of the impact bar and the large difference in wave impedance [16]. This lessens the transmitted wave received in the transmitted bar, making the transmitted energy so little and, thus, negligible. At the same time, the absorbed energy of the cemented backfill shows a trend first increasing and then decreasing with the increase in strain rate. This indicates that the cemented backfill has a better energy absorbed performance, although it may be limited as the energy cannot be absorbed after reaching the peak. The energy-absorbing performance is consistent with its dynamic peak intensity.
Minerals 2021, 11, x FOR PEER REVIEW 9 of 13 seen from Figure 9 that the incident energy of the cemented backfill and the reflected energy both increase as the strain rate increases. As the strain rate increases, the transmitted energy first decreases and then increases. However, transmitted energy is less than 1 J due to the large difference between the density of the cemented backfill and the density of the impact bar and the large difference in wave impedance [16]. This lessens the transmitted wave received in the transmitted bar, making the transmitted energy so little and, thus, negligible. At the same time, the absorbed energy of the cemented backfill shows a trend first increasing and then decreasing with the increase in strain rate. This indicates that the cemented backfill has a better energy absorbed performance, although it may be limited as the energy cannot be absorbed after reaching the peak. The energy-absorbing performance is consistent with its dynamic peak intensity.

Two-Dimensional Micros-Crack Distribution of CTB Specimens
The distribution of cracks and pores in the CTB was obtained by micro-CT scanning. When the ASR is 30 s −1 , the CTB after dynamic load was generally intact and scanned by micro-CT. The 2D images of the CTB samples were obtained by the slicing function of micro-CT with 0.5 mm spacing along the Z-direction of samples. ImageJ software (V1.8.0, National Institutes of Health, MD, USA) was used to binarize the CT slice images to make the cracks more clearly displayed and then used the analyze particles function to calculate the area ratio of the cracks to the entire slice. Finally, the results are shown in Figure 10. As the specimen's height increases and the specimen comes closer to the incident bar, the failure area of the specimen increases. Near the incident bar, the failure area of the CTB accounts for about 16% of the total area, whereas the failure area only accounts for about 1% near the transmitted bar. The crack area ratio is exponentially related to the specimen height. The correlation coefficient R 2 = 0.989 indicates that the exponential function has a high correlation, and the exponential equation relation is

Two-Dimensional Micros-Crack Distribution of CTB Specimens
The distribution of cracks and pores in the CTB was obtained by micro-CT scanning. When the ASR is 30 s −1 , the CTB after dynamic load was generally intact and scanned by micro-CT. The 2D images of the CTB samples were obtained by the slicing function of micro-CT with 0.5 mm spacing along the Z-direction of samples. ImageJ software (V1.8.0, National Institutes of Health, MD, USA) was used to binarize the CT slice images to make the cracks more clearly displayed and then used the analyze particles function to calculate the area ratio of the cracks to the entire slice. Finally, the results are shown in Figure 10. As the specimen's height increases and the specimen comes closer to the incident bar, the failure area of the specimen increases. Near the incident bar, the failure area of the CTB accounts for about 16% of the total area, whereas the failure area only accounts for about 1% near the transmitted bar. The crack area ratio is exponentially related to the specimen height. The correlation coefficient R 2 = 0.989 indicates that the exponential function has a high correlation, and the exponential equation relation is y = a * e − x b + y 0 , where a, b, and y 0 are constants (a = 0.12, b = −17.89, y 0 = 0.62). Minerals 2021, 11, x FOR PEER REVIEW 10 of Figure 10. Crack area distribution along Z-axis.
A slice image was taken every 10 mm for further analysis, as shown in Figure 10. can be seen that there are initial holes in CTB. A pseudo color-enhancing algorithm w used to process the micro-CT slice images to facilitate image analysis [40,41]. Figure shows that the part of CTB wherein the stress wave acts first (Z = 40 mm) had partly be spalled and had some cracks and micro-cracks. Furthermore (Z = 30 mm), the main crac and micro-cracks increased when the spalling area of CTB reduced. When Z=20 mm, t structure of CTB is intact without spalling, and there are two main cracks and one micr crack. When Z = 10 mm, the structure of CTB is also intact without spalling; although the are two main cracks, no micro-cracks are observed. According to the test results, when t CTB undergoes a different strain rate by Hopkinson dynamic load tests, only 30 s −1 r mains basically intact, and the others are impacted into fragments. Overall, it can be se that when the strain rate is 30 s −1 , CTB can maintain a complete shape with residu strength.

Failure Modes of CTB Specimens Analysis
The specimen or specimen pieces of the impacted cemented backfill are collected an summarized. The CTB specimen with a strain rate of 30 s −1 remains relatively intact aft the impact. Thus, this specimen was selected for micro-CT scanning, and other specim pieces were flattened and photographed into pictures. The pictures underwent grey-sca binarization processing. Table 4 shows the diagrams of each cemented backfill that is dam aged under different strain rates. In this section, the maximum block size of CTB was use to assess the failure degree. With the increase in the ASR from 54 to 98, the maximu block size of the CTB specimen decreased from 25 to 17 mm.
A slice picture was obtained every 0.5 mm using CT scan, and slice image data r constructed the damaged cemented backfill. The results are shown in Table 4. Distinctl at an ASR of 30 s −1 , CTB can still maintain a relatively intact shape. The entire surface the specimen shows tensile cracks. With the increase in ASR, it is obvious that the rate large blocks decreases, and the rate of small blocks increases after the cemented backfill damaged.
The specimen under dynamic load with the ASR of 30 s −1 was used for three-dime sional reconstruction of the crack. Figure 11 shows the different angles of the three-dime sional reconstruction of the crack of the specimen. Obviously, when the ASR is 30 s −1 , t transfixion crack of CTB is a tensile crack accompanied by a shear crack on the surfac Actually, the phenomenon of CTB or CPB failure was prone to occurring in pillar minin A slice image was taken every 10 mm for further analysis, as shown in Figure 10. It can be seen that there are initial holes in CTB. A pseudo color-enhancing algorithm was used to process the micro-CT slice images to facilitate image analysis [40,41]. Figure 10 shows that the part of CTB wherein the stress wave acts first (Z = 40 mm) had partly been spalled and had some cracks and micro-cracks. Furthermore (Z = 30 mm), the main cracks and micro-cracks increased when the spalling area of CTB reduced. When Z = 20 mm, the structure of CTB is intact without spalling, and there are two main cracks and one micro-crack. When Z = 10 mm, the structure of CTB is also intact without spalling; although there are two main cracks, no micro-cracks are observed. According to the test results, when the CTB undergoes a different strain rate by Hopkinson dynamic load tests, only 30 s −1 remains basically intact, and the others are impacted into fragments. Overall, it can be seen that when the strain rate is 30 s −1 , CTB can maintain a complete shape with residual strength.

Failure Modes of CTB Specimens Analysis
The specimen or specimen pieces of the impacted cemented backfill are collected and summarized. The CTB specimen with a strain rate of 30 s −1 remains relatively intact after the impact. Thus, this specimen was selected for micro-CT scanning, and other specimen pieces were flattened and photographed into pictures. The pictures underwent grey-scale binarization processing. Table 4 shows the diagrams of each cemented backfill that is damaged under different strain rates. In this section, the maximum block size of CTB was used to assess the failure degree. With the increase in the ASR from 54 to 98, the maximum block size of the CTB specimen decreased from 25 to 17 mm.
A slice picture was obtained every 0.5 mm using CT scan, and slice image data reconstructed the damaged cemented backfill. The results are shown in Table 4. Distinctly, at an ASR of 30 s −1 , CTB can still maintain a relatively intact shape. The entire surface of the specimen shows tensile cracks. With the increase in ASR, it is obvious that the rate of large blocks decreases, and the rate of small blocks increases after the cemented backfill is damaged.
The specimen under dynamic load with the ASR of 30 s −1 was used for threedimensional reconstruction of the crack. Figure 11 shows the different angles of the three-dimensional reconstruction of the crack of the specimen. Obviously, when the ASR is 30 s −1 , the transfixion crack of CTB is a tensile crack accompanied by a shear crack on the surface. Actually, the phenomenon of CTB or CPB failure was prone to occurring in pillar mining, such as the fragmentation and collapse of artificial CTB pillars. In addition, the deformation of the CTB or CPB in the downhand cut and fill mining method was also a typical type of tensile failure. dimensional reconstruction of the crack of the specimen. Obviously, when the ASR is 30 s −1 , the transfixion crack of CTB is a tensile crack accompanied by a shear crack on the surface. Actually, the phenomenon of CTB or CPB failure was prone to occurring in pillar mining, such as the fragmentation and collapse of artificial CTB pillars. In addition, the deformation of the CTB or CPB in the downhand cut and fill mining method was also a typical type of tensile failure.

Conclusions
In this paper, a series of laboratory tests, including the SHPB test, energy dissipation and micro-CT scan, was conducted on CTB specimens to explore their dynamica mechanics and microstructural characteristics. The conclusions are as follows: (1) In the SHPB test, the superimposed wave of the incident wave and reflected wave was almost equal to the amplitude of the transmitted wave, and the waveforms overlapped. The two ends of the CTB specimen in this experiment reached a stressed equilibrium. (2) When the ASR is 30-98 s −1 , with the increase in the ASR, the DUCS of the CTB shows a trend of first increasing and then decreasing. (3) The CTB also exhibits a strengthening effect of strain rate, and when the ASR is greater than 74 s −1 , the strengthening effect decreases. (4) As the ASR increases, the incident energy of the CTB increases, and the reflected energy also increases. The transmitted energy can be negligible, and the absorbed 25mm 20mm 17mm dimensional reconstruction of the crack of the specimen. Obviously, when the ASR is 30 s −1 , the transfixion crack of CTB is a tensile crack accompanied by a shear crack on the surface. Actually, the phenomenon of CTB or CPB failure was prone to occurring in pillar mining, such as the fragmentation and collapse of artificial CTB pillars. In addition, the deformation of the CTB or CPB in the downhand cut and fill mining method was also a typical type of tensile failure.

Conclusions
In this paper, a series of laboratory tests, including the SHPB test, energy dissipation, and micro-CT scan, was conducted on CTB specimens to explore their dynamical mechanics and microstructural characteristics. The conclusions are as follows: (1) In the SHPB test, the superimposed wave of the incident wave and reflected wave was almost equal to the amplitude of the transmitted wave, and the waveforms overlapped. The two ends of the CTB specimen in this experiment reached a stressed equilibrium. (2) When the ASR is 30-98 s −1 , with the increase in the ASR, the DUCS of the CTB shows a trend of first increasing and then decreasing. (3) The CTB also exhibits a strengthening effect of strain rate, and when the ASR is greater than 74 s −1 , the strengthening effect decreases. (4) As the ASR increases, the incident energy of the CTB increases, and the reflected energy also increases. The transmitted energy can be negligible, and the absorbed 25mm 20mm 17mm Minerals 2021, 11, x FOR PEER REVIEW 11 of 13 dimensional reconstruction of the crack of the specimen. Obviously, when the ASR is 30 s −1 , the transfixion crack of CTB is a tensile crack accompanied by a shear crack on the surface. Actually, the phenomenon of CTB or CPB failure was prone to occurring in pilla mining, such as the fragmentation and collapse of artificial CTB pillars. In addition, the deformation of the CTB or CPB in the downhand cut and fill mining method was also a typical type of tensile failure.

Conclusions
In this paper, a series of laboratory tests, including the SHPB test, energy dissipation and micro-CT scan, was conducted on CTB specimens to explore their dynamica mechanics and microstructural characteristics. The conclusions are as follows: (1) In the SHPB test, the superimposed wave of the incident wave and reflected wave was almost equal to the amplitude of the transmitted wave, and the waveforms overlapped. The two ends of the CTB specimen in this experiment reached a stressed equilibrium. (2) When the ASR is 30-98 s −1 , with the increase in the ASR, the DUCS of the CTB shows a trend of first increasing and then decreasing. (3) The CTB also exhibits a strengthening effect of strain rate, and when the ASR is greater than 74 s −1 , the strengthening effect decreases. (4) As the ASR increases, the incident energy of the CTB increases, and the reflected energy also increases. The transmitted energy can be negligible, and the absorbed 25mm 20mm 17mm Minerals 2021, 11, x FOR PEER REVIEW 11 of 13 dimensional reconstruction of the crack of the specimen. Obviously, when the ASR is 30 s −1 , the transfixion crack of CTB is a tensile crack accompanied by a shear crack on the surface. Actually, the phenomenon of CTB or CPB failure was prone to occurring in pillar mining, such as the fragmentation and collapse of artificial CTB pillars. In addition, the deformation of the CTB or CPB in the downhand cut and fill mining method was also a typical type of tensile failure.

Conclusions
In this paper, a series of laboratory tests, including the SHPB test, energy dissipation, and micro-CT scan, was conducted on CTB specimens to explore their dynamical mechanics and microstructural characteristics. The conclusions are as follows: (1) In the SHPB test, the superimposed wave of the incident wave and reflected wave was almost equal to the amplitude of the transmitted wave, and the waveforms overlapped. The two ends of the CTB specimen in this experiment reached a stressed equilibrium. (2) When the ASR is 30-98 s −1 , with the increase in the ASR, the DUCS of the CTB shows a trend of first increasing and then decreasing. (3) The CTB also exhibits a strengthening effect of strain rate, and when the ASR is greater than 74 s −1 , the strengthening effect decreases. (4) As the ASR increases, the incident energy of the CTB increases, and the reflected energy also increases. The transmitted energy can be negligible, and the absorbed 25mm 20mm 17mm Minerals 2021, 11, x FOR PEER REVIEW 11 of 13 dimensional reconstruction of the crack of the specimen. Obviously, when the ASR is 30 s −1 , the transfixion crack of CTB is a tensile crack accompanied by a shear crack on the surface. Actually, the phenomenon of CTB or CPB failure was prone to occurring in pillar mining, such as the fragmentation and collapse of artificial CTB pillars. In addition, the deformation of the CTB or CPB in the downhand cut and fill mining method was also a typical type of tensile failure.

Conclusions
In this paper, a series of laboratory tests, including the SHPB test, energy dissipation, and micro-CT scan, was conducted on CTB specimens to explore their dynamical mechanics and microstructural characteristics. The conclusions are as follows: (1) In the SHPB test, the superimposed wave of the incident wave and reflected wave was almost equal to the amplitude of the transmitted wave, and the waveforms overlapped. The two ends of the CTB specimen in this experiment reached a stressed equilibrium. (2) When the ASR is 30-98 s −1 , with the increase in the ASR, the DUCS of the CTB shows a trend of first increasing and then decreasing. (3) The CTB also exhibits a strengthening effect of strain rate, and when the ASR is greater than 74 s −1 , the strengthening effect decreases. (4) As the ASR increases, the incident energy of the CTB increases, and the reflected energy also increases. The transmitted energy can be negligible, and the absorbed 25mm 20mm 17mm Minerals 2021, 11, x FOR PEER REVIEW 11 of 13 dimensional reconstruction of the crack of the specimen. Obviously, when the ASR is 30 s −1 , the transfixion crack of CTB is a tensile crack accompanied by a shear crack on the surface. Actually, the phenomenon of CTB or CPB failure was prone to occurring in pillar mining, such as the fragmentation and collapse of artificial CTB pillars. In addition, the deformation of the CTB or CPB in the downhand cut and fill mining method was also a typical type of tensile failure.

Conclusions
In this paper, a series of laboratory tests, including the SHPB test, energy dissipation, and micro-CT scan, was conducted on CTB specimens to explore their dynamical mechanics and microstructural characteristics. The conclusions are as follows: (1) In the SHPB test, the superimposed wave of the incident wave and reflected wave was almost equal to the amplitude of the transmitted wave, and the waveforms overlapped. The two ends of the CTB specimen in this experiment reached a stressed equilibrium. (2) When the ASR is 30-98 s −1 , with the increase in the ASR, the DUCS of the CTB shows a trend of first increasing and then decreasing. (3) The CTB also exhibits a strengthening effect of strain rate, and when the ASR is greater than 74 s −1 , the strengthening effect decreases. (4) As the ASR increases, the incident energy of the CTB increases, and the reflected energy also increases. The transmitted energy can be negligible, and the absorbed 25mm 20mm 17mm Minerals 2021, 11, x FOR PEER REVIEW 11 of 13 dimensional reconstruction of the crack of the specimen. Obviously, when the ASR is 30 s −1 , the transfixion crack of CTB is a tensile crack accompanied by a shear crack on the surface. Actually, the phenomenon of CTB or CPB failure was prone to occurring in pillar mining, such as the fragmentation and collapse of artificial CTB pillars. In addition, the deformation of the CTB or CPB in the downhand cut and fill mining method was also a typical type of tensile failure.

Conclusions
In this paper, a series of laboratory tests, including the SHPB test, energy dissipation, and micro-CT scan, was conducted on CTB specimens to explore their dynamical mechanics and microstructural characteristics. The conclusions are as follows: (1) In the SHPB test, the superimposed wave of the incident wave and reflected wave was almost equal to the amplitude of the transmitted wave, and the waveforms overlapped. The two ends of the CTB specimen in this experiment reached a stressed equilibrium. (2) When the ASR is 30-98 s −1 , with the increase in the ASR, the DUCS of the CTB shows a trend of first increasing and then decreasing. (3) The CTB also exhibits a strengthening effect of strain rate, and when the ASR is greater than 74 s −1 , the strengthening effect decreases. (4) As the ASR increases, the incident energy of the CTB increases, and the reflected energy also increases. The transmitted energy can be negligible, and the absorbed 25mm 20mm 17mm Minerals 2021, 11, x FOR PEER REVIEW 11 of 13 dimensional reconstruction of the crack of the specimen. Obviously, when the ASR is 30 s −1 , the transfixion crack of CTB is a tensile crack accompanied by a shear crack on the surface. Actually, the phenomenon of CTB or CPB failure was prone to occurring in pillar mining, such as the fragmentation and collapse of artificial CTB pillars. In addition, the deformation of the CTB or CPB in the downhand cut and fill mining method was also a typical type of tensile failure.

Conclusions
In this paper, a series of laboratory tests, including the SHPB test, energy dissipation, and micro-CT scan, was conducted on CTB specimens to explore their dynamical mechanics and microstructural characteristics. The conclusions are as follows: (1) In the SHPB test, the superimposed wave of the incident wave and reflected wave was almost equal to the amplitude of the transmitted wave, and the waveforms overlapped. The two ends of the CTB specimen in this experiment reached a stressed equilibrium. (2) When the ASR is 30-98 s −1 , with the increase in the ASR, the DUCS of the CTB shows a trend of first increasing and then decreasing. (3) The CTB also exhibits a strengthening effect of strain rate, and when the ASR is greater than 74 s −1 , the strengthening effect decreases. (4) As the ASR increases, the incident energy of the CTB increases, and the reflected energy also increases. The transmitted energy can be negligible, and the absorbed 25mm 20mm 17mm Minerals 2021, 11, x FOR PEER REVIEW 11 of 13 such as the fragmentation and collapse of artificial CTB pillars. In addition, the deformation of the CTB or CPB in the downhand cut and fill mining method was also a typical type of tensile failure.

Conclusions
In this paper, a series of laboratory tests, including the SHPB test, energy dissipation, and micro-CT scan, was conducted on CTB specimens to explore their dynamical mechanics and microstructural characteristics. The conclusions are as follows: (1) In the SHPB test, the superimposed wave of the incident wave and reflected wave was almost equal to the amplitude of the transmitted wave, and the waveforms overlapped. The two ends of the CTB specimen in this experiment reached a stressed equilibrium. (2) When the ASR is 30-98 s −1 , with the increase in the ASR, the DUCS of the CTB shows a trend of first increasing and then decreasing. (3) The CTB also exhibits a strengthening effect of strain rate, and when the ASR is greater than 74 s −1 , the strengthening effect decreases. (4) As the ASR increases, the incident energy of the CTB increases, and the reflected energy also increases. The transmitted energy can be negligible, and the absorbed energy shows a trend of first increasing and then decreasing, which is consistent with its dynamic peak intensity.

Conclusions
In this paper, a series of laboratory tests, including the SHPB test, energy dissipation, and micro-CT scan, was conducted on CTB specimens to explore their dynamical mechanics and microstructural characteristics. The conclusions are as follows: (1) In the SHPB test, the superimposed wave of the incident wave and reflected wave was almost equal to the amplitude of the transmitted wave, and the waveforms overlapped. The two ends of the CTB specimen in this experiment reached a stressed equilibrium. (2) When the ASR is 30-98 s −1 , with the increase in the ASR, the DUCS of the CTB shows a trend of first increasing and then decreasing. (3) The CTB also exhibits a strengthening effect of strain rate, and when the ASR is greater than 74 s −1 , the strengthening effect decreases. (4) As the ASR increases, the incident energy of the CTB increases, and the reflected energy also increases. The transmitted energy can be negligible, and the absorbed energy shows a trend of first increasing and then decreasing, which is consistent with its dynamic peak intensity.
(5) The pseudo-color enhancement was carried out for the original CT slice image with micro-CT. Results show that the closer the specimen near the incident bar, the larger the crack area of the specimen. The crack area ratio is exponentially related to the specimen height.
In this study, the research finding has revealed the dynamical mechanics and microstructural characteristics of CTB. In future work, the further dynamic energy dissipation analysis of CTB will be considered. Additionally, the SHPB experiments with 3D-DIC techniques will be considered to observe the real progress of the crack development of CTB.