Skip to Content

56 Results Found

  • Article
  • Open Access
1 Citations
3,382 Views
12 Pages

4 July 2023

Fibre-reinforced shotcrete is an essential part of the support of hard rock tunnels. Due to the complexity of the design, a combination of empirical and numerical analysis is commonly used in the design. The required dosage of fibres for structural p...

  • Article
  • Open Access
20 Citations
6,000 Views
11 Pages

Indirect Tensile Behaviour of Fibre Reinforced Alkali-Activated Composites

  • Filipe Almeida,
  • Vítor M. C. F. Cunha,
  • Tiago Miranda and
  • Nuno Cristelo

14 May 2018

There are currently still some sustainability-related issues that need to be tackled within the construction sector. Namely, cement production is accountable for nearby 5% of the worldwide total CO2-eq release. Therefore, environmentally viable and e...

  • Article
  • Open Access
13 Citations
4,078 Views
14 Pages

16 January 2020

This article describes an experimental program developed to study the influence of longitudinal prestress on the behaviour of high-strength concrete hollow beams under pure torsion. The pre-cracking, the post-cracking and the ultimate behaviour are a...

(This article belongs to the Special Issue Architectural Structure)
  • Article
  • Open Access
5 Citations
2,235 Views
26 Pages

Comparative Study on the Impact of Various Non-Metallic Fibres on High-Performance Concrete Properties

  • Aleksandrs Korjakins,
  • Girts Kolendo,
  • Vitalijs Lusis,
  • Laura Spure and ,
  • Kaspars Bondars,
  • Diana Bajare and
  • Genadijs Sahmenko
  • + 2 authors+ 0 author

17 November 2024

The performance of high-performance concrete has been enhanced in the present study by incorporating non-metallic fibres without altering the binder content. The impact of these fibres on high-performance concrete flexural and compression characteris...

(This article belongs to the Special Issue Novel Cement and Concrete Materials)
  • Article
  • Open Access
2,778 Views
11 Pages

26 December 2022

This study presents analysis of two types of experimental test related to the crack propagation in concrete specimens subjected to high-sustained loading levels and quasi-static loadings. The concept of the equivalent crack length is introduced to pe...

(This article belongs to the Topic Advances on Structural Engineering, 2nd Volume)
  • Article
  • Open Access
5 Citations
3,910 Views
20 Pages

Modern concrete mix design is a complex process involving superplasticisers, fine powders, and fibres, requiring time and energy due to the high number of trial tests needed to achieve rheological properties in the fresh state. Concrete batching invo...

(This article belongs to the Section Building Materials, and Repair & Renovation)
  • Article
  • Open Access
11 Citations
9,631 Views
23 Pages

In a previously published study, the authors explained the formal design efficiency of the 3D-printed biodigital clay bricks 3DPBDCB: a project that aimed to change the conventional methods of clay brick design and mass production. This was achieved...

  • Review
  • Open Access
644 Views
39 Pages

24 August 2026

Natural fibres, both bio-based and mineral-derived, are increasingly investigated for use in mortar as a means of improving technical efficiency while potentially reducing reliance on synthetic fibres where performance and durability are adequate. Th...

(This article belongs to the Special Issue Bio-Based Building Materials for Environmental Applications)
  • Review
  • Open Access
191 Views
45 Pages

Fibre-Reinforced Concrete at Elevated Temperatures: Damage Mechanisms, Spalling, and Residual Performance

  • Jinbo Xie,
  • Wenlong Zhao,
  • Xi Du,
  • Lixin Chang and ,
  • Yungui Pan and
  • Qinglong You
  • + 1 author+ 0 author

19 October 2026

Fibre-reinforced concrete exhibits complex deterioration when exposed to elevated temperatures because of physicochemical degradation, moisture migration, thermal incompatibility, pore-pressure development, and progressive cracking. Previous reviews...

(This article belongs to the Special Issue Performance Enhancement of New and Existing Concrete and Masonry Structural Materials)
  • Review
  • Open Access
1,396 Views
40 Pages

End-of-life tyres present a significant waste management challenge, prompting increasing interest in the use of tyre-derived materials in engineering applications. This review critically evaluates the performance of tyre-derived materials across conc...

(This article belongs to the Special Issue Sustainable Environmental Solutions: Waste Valorization, Water Protection, and Soil Management)
  • Article
  • Open Access
12 Citations
1,769 Views
19 Pages

15 August 2025

This study investigates the flexural performance, tensile splitting strength, and fracture behaviour of self-compacting concrete (SCC) reinforced with polypropylene (PP) and basalt (BF) fibres. A total of eleven SCC mixtures with varying fibre types...

(This article belongs to the Special Issue Advances in Modern Cement-Based Materials for Composite Structures)
  • Article
  • Open Access
2 Citations
2,185 Views
31 Pages

Behaviour Analysis of Timber–Concrete Composite Floor Structure with Granite Chip Connection

  • Anna Haijima,
  • Elza Briuka,
  • Janis Sliseris,
  • Dmitrijs Serdjuks and ,
  • Arturs Ziverts and
  • Vjaceslavs Lapkovskis
  • + 1 author+ 0 author

2 October 2025

This study investigates the mechanical behaviour of timber–concrete composite (TCC) floor members with an innovative adhesive connection reinforced by granite chips, glass fibre yarn net in the epoxy adhesive layer, and polypropylene (PP) fibre...

(This article belongs to the Special Issue Behaviour and Analysis of Timber–Concrete Composite Structures)
  • Review
  • Open Access
18 Citations
7,461 Views
26 Pages

Chloride-Induced Corrosion Effects on the Structural Performance of Concrete with Rebar and Fibres: A Review

  • Petar Bajić,
  • Bruno Leporace-Guimil,
  • Carmen Andrade,
  • Nikola Tošić and
  • Albert de la Fuente

8 June 2025

Chloride-induced corrosion is a major contributor in the degradation of standardised steel-based products (e.g., rebars and fibres) commonly used for reinforcing concrete structures. Since cracked reinforced concrete elements are determined to be mor...

(This article belongs to the Special Issue Fiber-Reinforced Concrete: Recent Progress and Future Directions)
  • Article
  • Open Access
15 Citations
4,504 Views
13 Pages

Mechanical Performance of Concrete Made with the Addition of Recycled Macro Plastic Fibres

  • Pietro A. Vaccaro,
  • Adela P. Galvín,
  • Jesús Ayuso,
  • Auxi Barbudo and
  • Antonio López-Uceda

22 October 2021

For many decades, researchers have been working on finding innovative and sustainable solutions to address the enormous quantities of plastic waste that are produced every year which, after being collected, are transformed into energy, recycled, or s...

(This article belongs to the Special Issue Advances in Recycling of Construction Materials)
  • Article
  • Open Access
599 Views
18 Pages

From Laboratory to Building Scale: A Digital-Twin Methodology for Resilience-Oriented Assessment of RC Infrastructure Using Waste Wool-Fibre Cementitious Materials

  • Carlos Ruiz-Díaz,
  • Paula Triviño-Tarradas,
  • Guillermo Guerrero-Vacas,
  • Óscar Rodríguez-Alabanda and ,
  • Pedro Medina-Triviño and
  • María M. Serrano-Baena
  • + 1 author+ 0 author

16 April 2026

As natural and anthropogenic hazards intensify, improving the performance of reinforced-concrete (RC) infrastructure within a resilience-oriented assessment framework while limiting environmental burdens has become an important challenge for sustaina...

(This article belongs to the Special Issue Sustainable Risk Management and Resilient Infrastructure)
  • Article
  • Open Access
2 Citations
2,561 Views
26 Pages

Toughness of Natural Hydraulic Lime Fibre-Reinforced Mortars for Masonry Strengthening Overlay Systems

  • João A. P. P. Almeida,
  • Joaquim A. O. Barros and
  • Eduardo N. B. Pereira

27 February 2024

Masonry structures are susceptible to damage and collapse due to seismic actions, a problem in many urban areas. To address this issue, researchers are studying the use of fibre-reinforced mortars as overlay strengthening systems. This study assessed...

(This article belongs to the Special Issue Advances in Cement-Based Materials)
  • Feature Paper
  • Article
  • Open Access
265 Citations
17,437 Views
22 Pages

Experimental Exploration of Metal Cable as Reinforcement in 3D Printed Concrete

  • Freek P. Bos,
  • Zeeshan Y. Ahmed,
  • Evgeniy R. Jutinov and
  • Theo A. M. Salet

16 November 2017

The Material Deposition Method (MDM) is enjoying increasing attention as an additive method to create concrete mortar structures characterised by a high degree of form-freedom, a lack of geometrical repetition, and automated construction. Several sma...

(This article belongs to the Special Issue NextGen Materials for 3D Printing)
  • Article
  • Open Access
5 Citations
3,901 Views
28 Pages

Insights on Lattice Discrete Particle Model Calibration and Validation Procedure to Simulate Polypropylene and Steel Fibre-Reinforced Concrete

  • Sushant Poudel,
  • Antonio Cibelli,
  • Clementina Del Prete,
  • Roman Wan-Wendner and ,
  • Claudio Mazzotti and
  • Nicola Buratti
  • + 1 author+ 0 author

5 February 2025

The use of fibre-reinforced concrete (FRC) has been substantially increasing in the last few years, in different fields of the construction industry. Recently, many experiments have been performed to observe the short- and long-term mechanical behavi...

  • Article
  • Open Access
410 Views
31 Pages

Performance of Reinforced Concrete–UHPC Composite Slabs Under Four-Point Bending: Experimental Tests, Numerical Simulations and Analytical Methods

  • Qi-Chun Wang,
  • Jun Peng,
  • Hui-Qiang Yan,
  • Yong-Xin Yang and ,
  • Shao-Bo Kang,
  • Yi Chen and
  • Qiao-Ling Fu
  • + 2 authors+ 0 author

3 August 2026

This study investigates the behaviour of normal-strength concrete (NSC)–ultra-high-performance concrete (UHPC) composite slabs under four-point bending through experimental tests, finite element simulations, and analytical modelling. A total of...

(This article belongs to the Section Building Structures)
  • Article
  • Open Access
704 Views
25 Pages

26 April 2026

This article analyses the possibility of the application of advanced fasteners in the construction of steel–concrete composite beams. The fasteners were made of corrugated metal sheet with a thickness of 1.00 mm, were in a dovetail shape, and h...

(This article belongs to the Section Construction and Building Materials)
  • Article
  • Open Access
39 Citations
5,829 Views
21 Pages

Effect of Fibre Material and Fibre Roughness on the Pullout Behaviour of Metallic Micro Fibres Embedded in UHPC

  • Niels Wiemer,
  • Alexander Wetzel,
  • Maximilian Schleiting,
  • Philipp Krooß and ,
  • Malte Vollmer,
  • Thomas Niendorf,
  • Stefan Böhm and
  • Bernhard Middendorf
  • + 3 authors+ 0 author

14 July 2020

The use of micro fibres in Ultra-High-Performance Concrete (UHPC) as reinforcement increases tensile strength and especially improves the post-cracking behaviour. Without using fibres, the dense structure of the concrete matrix results in a brittle f...

(This article belongs to the Special Issue High and Ultra-High Performance Concrete for Sustainable Construction)
  • Article
  • Open Access
15 Citations
3,446 Views
14 Pages

Development of Sustainable Concrete from Hypo Sludge Combined with Basalt Fibre and Latex

  • Krishnan Chandra Sekar,
  • Ramasamy Murugesan,
  • Muthusamy Sivaraja and
  • Ramaiah Prakash

13 July 2023

Cement production is a major source of carbon dioxide pollution. An environmentally friendly concrete needs to be developed in order to overcome the adverse environmental impacts of cement production and the continuing depletion of natural resources....

  • Article
  • Open Access
11 Citations
4,319 Views
20 Pages

Torsional Behaviour of Steel Fibre Reinforced Alkali Activated Concrete

  • Chee Keong Lau,
  • Trevor N. S. Htut,
  • Jack J. Melling,
  • Amin Chegenizadeh and
  • Tian Sing Ng

3 August 2020

Nine alkali-activated concrete beams were produced and tested under pure torsional load to failure. The alkali-activated concrete beams were produced with following variables: (i) fibres only, (ii) conventionally reinforced or (iii) a hybrid of both...

(This article belongs to the Special Issue Concrete and Construction Materials)
  • Article
  • Open Access
571 Views
20 Pages

7 June 2026

This study investigates the effects of polypropylene fibre content on the workability and compressive strength of recycled aggregate concrete (RAC), as well as the flexural behaviour of RAC beams. The results indicate that recycled aggregates adverse...

(This article belongs to the Section Green Building)
  • Article
  • Open Access
14 Citations
4,002 Views
25 Pages

Experimental Research and Numerical Analysis of CFRP Retrofitted Masonry Triplets under Shear Loading

  • Houria Hernoune,
  • Benchaa Benabed,
  • Rajab Abousnina,
  • Abdalrahman Alajmi and ,
  • Abdullah M GH Alfadhili and
  • Abdullah Shalwan
  • + 1 author+ 0 author

6 September 2022

This paper presents an experimental and numerical study into the shear response of brick masonry triplet prisms under different levels of precompression, as well as samples reinforced with carbon fiber-reinforced polymer (CFRP) strips. Masonry triple...

(This article belongs to the Special Issue Polymer Fiber and Nanowire Reinforced Materials)
  • Article
  • Open Access
11 Citations
3,941 Views
32 Pages

Experimental and Numerical Research of Post-Tensioned Concrete Beams

  • Anna Jancy,
  • Adam Stolarski and
  • Jacek Zychowicz

1 June 2023

The purpose of this paper is to present a new approach for the modelling of post-tensioned beams with calibration of the FE model to experimental results until the load capacity and post-critical state are reached. Two post-tensioned beams with diffe...

(This article belongs to the Special Issue Masonry Structures and Reinforced Concrete Structures)
  • Article
  • Open Access
13 Citations
3,836 Views
20 Pages

Phase Field Simulation of Laminated Glass Beam

  • Francesco Freddi and
  • Lorenzo Mingazzi

20 July 2020

The complex failure mechanisms of glass laminates under in-plane loading conditions is modelled within the framework of phase-field strategy. Laminated glass is widely used for structural purposes due to its safe post-glass-breakage response. In fact...

(This article belongs to the Special Issue Fracture Mechanics and Phase Field Approaches in Engineering Materials)
  • Feature Paper
  • Article
  • Open Access
33 Citations
3,508 Views
10 Pages

Modelling the Variability and the Anisotropic Behaviour of Crack Growth in SLM Ti-6Al-4V

  • Rhys Jones,
  • Calvin Rans,
  • Athanasios P. Iliopoulos,
  • John G. Michopoulos and ,
  • Nam Phan and
  • Daren Peng
  • + 1 author+ 0 author

13 March 2021

The United States Air Force (USAF) Guidelines for the Durability and Damage Tolerance (DADT) certification of Additive Manufactured (AM) parts states that the most difficult challenge for the certification of an AM part is to establish an accurate pr...

(This article belongs to the Special Issue The Science and Technology of 3D Printing)
  • Article
  • Open Access
137 Views
17 Pages

Hygrothermal Degradation Effects on Mode I Fracture in Adhesively Bonded Carbon–Epoxy Composites

  • Paula Vigón,
  • Antonio Argüelles,
  • Jaime Viña,
  • Luis Álvarez-Gómez and
  • Miguel Lozano

31 October 2026

Hygrothermal ageing can affect the mechanical performance of adhesively bonded carbon-fibre reinforced polymer (CFRP) joints under both static and fatigue loading. Understanding how their fracture behaviour evolves with exposure time is important for...

(This article belongs to the Special Issue Degradation Mechanisms, Durability Enhancement and Decommission of Composite Materials)
  • Article
  • Open Access
8 Citations
3,882 Views
19 Pages

11 September 2020

This paper presents the development of a numerical model aimed at the simulation of nonlinear behaviour of traditional joints between walls made of autoclaved aerated concrete (AAC) masonry units. Nonlinear behaviour and cracking of AAC and mortar we...

(This article belongs to the Special Issue Masonry Structures and Reinforced Concrete Structures)
  • Proceeding Paper
  • Open Access
156 Views
10 Pages

20 October 2026

Post-tensioned reinforcement can be used in different structural arrangements. Bonded internal tendons are usually grouted with cement mortar, whereas internal or external unbonded tendons use wax or grease. This selection significantly affects crack...

(This article belongs to the Proceedings of The 15th Central European Congress on Concrete Engineering)
  • Article
  • Open Access
10 Citations
4,683 Views
17 Pages

21 August 2021

The paper presents a failure analysis of the bell tower of the church of St. Francis of Assisi on Kaptol in Zagreb subjected to seismic activity using the finite-discrete element method—FDEM. The bell tower is a masonry building, and throughout histo...

(This article belongs to the Special Issue Selected Papers from the 1st Croatian Conference on Earthquake Engineering (1CroCEE))
  • Article
  • Open Access
4 Citations
1,939 Views
16 Pages

X-IGA Used for Orthotropic Material Crack Growth

  • Mohammed Berrada Gouzi,
  • Ahmed El Khalfi,
  • Sorin Vlase and
  • Maria Luminita Scutaru

2 August 2024

In this paper, we propose a new approach for numerically simulating the growth of cracks in unidirectional composite materials, termed extended isogeometric analysis, evaluating the maximum stress intensity factor and T-stress. To validate our approa...

  • Article
  • Open Access
23 Citations
12,016 Views
10 Pages

5 December 2014

This article describes the susceptibility of 316L stainless steel to stress corrosion cracking (SCC) in a nitrite-containing chloride solution. Slow strain rate testing (SSRT) in 30 wt. % MgCl2 solution established SCC susceptibility, as evidenced b...

(This article belongs to the Special Issue Corrosion of Materials)
  • Article
  • Open Access
33 Citations
6,168 Views
19 Pages

Influence of LPBF-Surface Characteristics on Fatigue Properties of Scalmalloy®

  • Jens Musekamp,
  • Thorsten Reiber,
  • Holger Claus Hoche,
  • Matthias Oechsner and ,
  • Matthias Weigold and
  • Eberhard Abele
  • + 1 author+ 0 author

6 December 2021

Laser powder bed fusion (LPBF) has indisputable advantages when designing new components with complex geometries due to toolless manufacturing and the ability to manufacture components with undercuts. However, fatigue properties rely heavily on the s...

(This article belongs to the Topic Additive Manufacturing)
  • Article
  • Open Access
5 Citations
4,129 Views
23 Pages

This research investigates the fatigue behaviour and fracture mechanics of high-performance concrete (HPC), including various compositions such as HPC with basalt aggregates (HPC-B), HPC with gravel (HPC-G), and high-strength coarse mortar (CM) under...

  • Review
  • Open Access
161 Views
28 Pages

9 November 2026

Laser Powder Bed Fusion (LPBF) enables the manufacturing of complex Ti6Al4V components, but the resulting mechanical and fatigue responses are condition-dependent. This critical narrative review examines how alloy grade and interstitial chemistry, po...

(This article belongs to the Special Issue Advances in Additive Manufacturing: Microstructure, Toughness and Mechanical Properties)
  • Article
  • Open Access
38 Citations
7,201 Views
16 Pages

Cold-Rolling Strain Hardening Effect on the Microstructure, Serration-Flow Behaviour and Dislocation Density of Friction Stir Welded AA5083

  • Zainuddin Sajuri,
  • Nor Fazilah Mohamad Selamat,
  • Amir Hossein Baghdadi,
  • Armin Rajabi and ,
  • Mohd Zaidi Omar,
  • Amir Hossein Kokabi and
  • Junaidi Syarif
  • + 2 authors+ 0 author

2 January 2020

5083 aluminium (Al) alloy materials have extensive structural applications in transportation industries because of their high strength-to-weight ratio and corrosion resistance. However, under conventional fusion weldings, these materials are limited...

  • Article
  • Open Access
2 Citations
1,911 Views
16 Pages

12 December 2024

Two identically sized RC beams were fabricated to investigate the effects of explosive loads on the flexural behaviour of Reinforced Concrete (RC) beams. One of the beams was subjected to an explosive load to induce post-explosion damage, and subsequ...

(This article belongs to the Special Issue Advanced Sensing Technology in Structural Health Monitoring)
  • Feature Paper
  • Article
  • Open Access
79 Citations
9,284 Views
19 Pages

Effect of Surface and Subsurface Defects on Fatigue Behavior of AlSi10Mg Alloy Processed by Laser Powder Bed Fusion (L-PBF)

  • Milad Hamidi Nasab,
  • Alessandro Giussani,
  • Dario Gastaldi,
  • Valeria Tirelli and
  • Maurizio Vedani

29 September 2019

The fatigue behaviour of an AlSi10Mg alloy processed by laser powder bed fusion (L-PBF) and subjected to different surface finishing processes was investigated paying special attention to the residual defects on the surface and the dominant fatigue f...

  • Article
  • Open Access
2 Citations
981 Views
18 Pages

Optimization of Sisal Content in Geopolymer Mortars with Recycled Brick and Concrete: Design and Processing Implications

  • Oscar Graos-Alva,
  • Aldo Castillo-Chung,
  • Marisol Contreras-Quiñones and
  • Alexander Vega-Anticona

Geopolymer mortars were produced from construction and demolition waste using a binary binder of recycled brick powder/recycled concrete powder (RBP/RCP = 70/30 wt%), activated with a hybrid alkaline solution (NaOH/Na2SiO3/KOH) and reinforced with si...

  • Article
  • Open Access
22 Citations
7,929 Views
19 Pages

4 December 2019

Several surface modification technologies are typically applied to improve the mechanical properties of the material surface of structural components subjected to severe conditions of load, wear and chemical erosion of the surface. The nitrocarburizi...

(This article belongs to the Special Issue Fatigue Design and Defects in Metals and Alloys)
  • Article
  • Open Access
5 Citations
3,143 Views
14 Pages

To study the residual lateral capacity of reinforced concrete (RC) columns after being subjected to static and horizontal impact action, static and horizontal impact tests of a total of sixteen RC columns were conducted. The variables considered in t...

(This article belongs to the Special Issue Sustainability and Resiliency of Building Materials and Structures)
  • Article
  • Open Access
156 Views
41 Pages

Self-compacting concrete (SCC) is widely used in reinforced concrete structures, yet its residual structural behaviour after fire exposure remains insufficiently understood, particularly under the combined effects of mixture composition, heating rate...

  • Review
  • Open Access
1 Citations
1,241 Views
22 Pages

Fibre-Reinforced Earth-Based 3D Printing: A Review of Mechanical Performance and Environmental Sustainability

  • Karim Fahfouhi,
  • Alberto Leal Matilla,
  • Daniel Ferrández,
  • Alfonso Cobo and ,
  • Humberto Varum,
  • Helena Bártolo and
  • Ana Sofia Guimarães
  • + 2 authors+ 0 author

11 April 2026

Earth-based additive manufacturing (AM) combines design flexibility and automation of 3D printing (3DP) with low embodied energy, local availability, and circular economy compatibility of earthen materials. However, the sustainability performance of...

(This article belongs to the Special Issue Innovative Approaches in Earthquake and Structural Engineering: Resilience, Performance, and Sustainability)
  • Article
  • Open Access
442 Views
31 Pages

7 August 2026

Magnesium alloys are promising candidates for biomedical implants, but their rapid corrosion limits clinical use. Simulated body fluid (SBF) is commonly used to evaluate corrosion behaviour; however, Ca-P and carbonate deposits can mask the intrinsic...

(This article belongs to the Special Issue Advances in Surface Engineering and Biocompatible Coatings for Biomedical Applications, 3rd Edition)
  • Article
  • Open Access
11 Citations
3,395 Views
21 Pages

Towards an Understanding of the Effect of Adding a Foam Core on the Blast Performance of Glass Fibre Reinforced Epoxy Laminate Panels

  • Sherlyn Gabriel,
  • Christopher J. von Klemperer,
  • Steeve Chung Kim Yuen and
  • Genevieve S. Langdon

23 November 2021

This paper presents insights into the blast response of sandwich panels with lightweight foam cores and asymmetric (different thicknesses) glass fibre epoxy face sheets. Viscously damped elastic vibrations were observed in the laminates (no core), wh...

(This article belongs to the Special Issue Sandwich Composites: Design, Simulation and Applications)
  • Article
  • Open Access
296 Views
26 Pages

Investigation of the Mechanical Properties and Strain-Displacement Field Evolution of the Rock-like Backfill Composite Structure Under Biaxial Loading

  • Pengtao Wang,
  • Jiajian Li,
  • Weidong Song,
  • Bolin Tang and ,
  • Zaihai Wu,
  • Hanwen Jia and
  • Xiaofei Li
  • + 2 authors+ 0 author

7 September 2026

In the subsequent backfilling mining method, the composite structure formed by the ore pillar and the backfill is the key element in ensuring the stability of the working face. Its mechanical behaviour directly affects mining safety and ore recovery...

  • Article
  • Open Access
5 Citations
4,678 Views
21 Pages

Extruded-Calendered Sheets of Fully Recycled PP/Opaque PET Blends: Mechanical and Fracture Behaviour

  • David Loaeza,
  • Jonathan Cailloux,
  • Orlando Santana Pérez,
  • Miguel Sánchez-Soto and
  • Maria Lluïsa Maspoch

19 July 2021

This work presents the experimental results of the mechanical and fracture behaviour of three polymeric blends prepared from two recycled plastics, namely polypropylene and opaque poly (ethylene terephthalate), where the second one acted as a reinfor...

(This article belongs to the Special Issue State-of-the-Art Polymer Science and Technology in Spain (2020,2021))
  • Article
  • Open Access
1 Citations
3,139 Views
23 Pages

This paper is focused on the retrofitting techniques of Zuo-Dou connections in Dieh-Dou timber frames in Far East Asia. The target is to develop appropriate techniques for the reinforcement and maintenance of the wooden cultural heritage. A series of...

(This article belongs to the Special Issue Advances in Building Conservation)

of 2