Skip to Content

97 Results Found

  • Article
  • Open Access
4 Citations
3,061 Views
12 Pages

31 October 2019

A tribotester with an integrated load sensor based on a strain gauge is typically used to measure the friction coefficient generated by the contact-related sliding motion of two objects. Since the friction coefficient is obtained by dividing the meas...

(This article belongs to the Section A: Physics)
  • Article
  • Open Access
390 Views
23 Pages

Multi-stage cold forging processes are widely adopted in actual industrial manufacturing of complex components. However, the influence of deformation history on lubrication behavior during such processes has not been fully clarified. This study inves...

  • Article
  • Open Access
1 Citations
1,025 Views
11 Pages

The Influence of Ball Surface Properties on the Friction and Wear Results of the Four-Ball Tribo-Test

  • Raimondas Kreivaitis,
  • Irenijus Rastokas,
  • Paulius Bendžiūnas,
  • Adolfo Senatore and ,
  • Audrius Žunda and
  • Simona Tučkutė
  • + 1 author+ 0 author

Lubricity is critical for maintaining the reliability of mechanical systems. Consistent monitoring of in-service lubricants and the development of new formulations require reliable test equipment and standardised procedures. The four-ball tribo-test...

  • Article
  • Open Access
10 Citations
2,696 Views
14 Pages

Investigation of the Lubricating Conditions in a Reciprocating Sliding Tribotest with Applied Electric Voltage

  • Raimondas Kreivaitis,
  • Albinas Andriušis,
  • Jolanta Treinytė,
  • Artūras Kupčinskas and
  • Vytenis Jankauskas

The appearance, evolution, and proliferation of electric-vehicle motors have introduced new challenges for lubricants. The appearance of electric currents in the shafts of electric motors can dramatically change the original properties of lubricated...

  • Review
  • Open Access
14 Citations
7,495 Views
23 Pages

High Temperature Tribology under Linear Oscillation Motion

  • Raj Shah,
  • Rui Chen,
  • Mathias Woydt,
  • Christoph Baumann and ,
  • Joshua Jurs and
  • Philip Iaccarino
  • + 1 author+ 0 author

High temperature tribology is considered to begin from a minimum temperature of 300–350 °C, where organic base oils and polymers begin to decompose, until a temperature of 1000 °C. In this field of tribology, tests are typically run und...

(This article belongs to the Special Issue In Commemoration of Professor Duncan Dowson: Tribology: Hydrodynamics, Elastohydrodynamics and Biotribology)
  • Feature Paper
  • Article
  • Open Access
37 Citations
6,188 Views
12 Pages

On the Improvement of AA2024 Wear Properties through the Deposition of a Cold-Sprayed Titanium Coating

  • Antonello Astarita,
  • Felice Rubino,
  • Pierpaolo Carlone,
  • Alessandro Ruggiero and ,
  • Claudio Leone,
  • Silvio Genna,
  • Massimiliano Merola and
  • Antonino Squillace
  • + 3 authors+ 0 author

11 August 2016

This paper deals with the study of the enhancement of the tribological properties of AA2024 through the deposition of a titanium coating. In particular two different coatings were studied: (1) untreated titanium coating; and (2) post-deposition laser...

(This article belongs to the Special Issue Aluminum Alloys)
  • Article
  • Open Access
9 Citations
3,174 Views
10 Pages

Wear Resistance of the Glass-Fiber Reinforced Polymer Composite with the Addition of Quartz Filler

  • Wojciech Zurowski,
  • Jarosław Zepchło,
  • Aneta Krzyzak,
  • Edwin Gevorkyan and ,
  • Mirosław Rucki,
  • Elżbieta Siek and
  • Anita Białkowska
  • + 2 authors+ 0 author

8 July 2021

The paper presents the results of investigations on the glass fiber reinforced composite for the floor panels with quartz powder additions of different percentages in terms of wear resistance, friction coefficient, hardness, and strength. The wear re...

(This article belongs to the Special Issue Tribology: Friction and Wear of Engineering Materials (Second Volume))
  • Article
  • Open Access
11 Citations
3,590 Views
23 Pages

Effect of Sliding on the Relation of Tribofilm Thickness and Wear

  • Martin Jech,
  • Maria L. Miranda-Medina,
  • Thomas Wopelka,
  • Christian Tomastik and
  • Carsten Gachot

10 February 2023

The formation of tribofilms depends on temperature, shear stress, availability of the related chemical components, and characteristics of the near surface region, e.g., roughness and surface chemistry. The purpose of a tribofilm is to separate two sl...

  • Article
  • Open Access
28 Citations
6,187 Views
11 Pages

Design and Construction of a Micro-Tribotester for Precise In-Situ Wear Measurements

  • Oleksiy V. Penkov,
  • Mahdi Khadem,
  • Andy Nieto,
  • Tae-Hyeong Kim and
  • Dae-Eun Kim

28 March 2017

Extensive research efforts have been devoted to understand the complex mechanisms of wear with the aim to minimize wear in sliding systems. Improvements in the instruments used for the characterization of the wear phenomenon are required to enhance t...

(This article belongs to the Special Issue Microtribology, Adhesion and Surface Engineering)
  • Article
  • Open Access
1 Citations
1,766 Views
17 Pages

The control of lubricity induced by electric potential is appealing for numerous applications. On the other hand, the high polarity of ionic liquids facilitates the adsorption of equally charged molecules onto polar surfaces. This phenomenon and its...

  • Article
  • Open Access
11 Citations
6,902 Views
20 Pages

Liquid lubricants are critical to enable long-life operation of high-performance machinery, such as geared actuators employed in robotics. In space applications, actuator gearboxes must operate in low temperatures, where liquid lubricants face inhere...

(This article belongs to the Special Issue Adaptive/Smart Structures and Multifunctional Materials in Aerospace)
  • Article
  • Open Access
28 Citations
5,016 Views
14 Pages

Optimization of the Rheological Properties and Tribological Performance of SAE 5w-30 Base Oil with Added MWCNTs

  • Bahaa M. Kamel,
  • Vineet Tirth,
  • Ali Algahtani,
  • Mohamed S. Shiba and ,
  • Ahmed Mobasher,
  • Hassan Abu Hashish and
  • Sameh Dabees
  • + 2 authors+ 0 author

16 September 2021

The augmentation of lubricant oil properties is key to protecting engines, bearings, and machine parts from damage due to friction and wear and minimizing energy lost in countering friction. The tribological and rheological properties of the lubrican...

  • Article
  • Open Access
11 Citations
6,198 Views
25 Pages

A Semantic Annotation Pipeline towards the Generation of Knowledge Graphs in Tribology

  • Patricia Kügler,
  • Max Marian,
  • Rene Dorsch,
  • Benjamin Schleich and
  • Sandro Wartzack

Within the domain of tribology, enterprises and research institutions are constantly working on new concepts, materials, lubricants, or surface technologies for a wide range of applications. This is also reflected in the continuously growing number o...

(This article belongs to the Special Issue Machine Learning in Tribology)
  • Article
  • Open Access
2 Citations
1,847 Views
13 Pages

27 September 2024

In this study, we analyze the extent to which thin hard coatings can serve as tribological protective layers for the selected plastic substrate materials PA12 (polyamide 12) und PEEK (polyetheretherketone), with and without fiber reinforcement. The a...

(This article belongs to the Special Issue Tribology in Germany: Latest Research and Development)
  • Article
  • Open Access
17 Citations
5,801 Views
17 Pages

Tests of Dental Properties of Composite Materials Containing Nanohybrid Filler

  • Jarosław Zubrzycki,
  • Tomasz Klepka,
  • Magdalena Marchewka and
  • Robert Zubrzycki

30 December 2022

Complex composite materials are used in many areas of dentistry. Initially, chemically hardened materials were also used, and in this group nanohybrid composites are highly valued. They are often used today, mainly for the direct reconstruction of da...

(This article belongs to the Section Polymeric Materials)
  • Article
  • Open Access
2 Citations
1,620 Views
17 Pages

Effect of Current Density on Mechanical and Tribological Properties of Wear-Resistant Cr Coatings

  • Mária Hagarová,
  • Gabriela Baranová,
  • Alica Mašlejová,
  • Peter Horňak and ,
  • Dávid Csík,
  • Marek Vojtko and
  • Martin Truchlý
  • + 2 authors+ 0 author

30 October 2025

As a functional coating, the wear-resistant Cr coating is of considerable importance in metal plating. In the present paper, S235 steel samples were electrodeposited with 5 µm thick Cr coating at current densities of 15, 27 and 40 A dm−2....

(This article belongs to the Section Inorganic Crystalline Materials)
  • Article
  • Open Access
2 Citations
934 Views
24 Pages

Improving Tribological Properties of Oil-in-Water Lubricating Fluid Using Hybrid Protic Ionic Liquid and Nanoparticle Additives

  • Raimondas Kreivaitis,
  • Jolanta Treinytė,
  • Artūras Kupčinskas,
  • Milda Gumbytė and
  • Ieva Gaidė

Water is attractive as a base fluid due to its availability and environmental friendliness. To enhance its lubricity, environmentally friendly additives must be applied. This study combined protic ionic liquid and several nanoparticles to form hybrid...

(This article belongs to the Special Issue Lubrication Mechanism of Ionic Liquids)
  • Article
  • Open Access
7 Citations
4,411 Views
15 Pages

In recent years, additive manufacturing methods such as Fused Layer Modeling have been continuously improved by industry and research institutions. In many cases, the influence of process control on the mechanical component properties is being invest...

(This article belongs to the Special Issue Additive Manufacturing and Device Applications)
  • Article
  • Open Access
26 Citations
6,591 Views
18 Pages

This paper reports the sliding wear properties and wear mechanisms of Hadfield high-Mn austenitic steel in a dry-sliding reciprocal tribotest against a WC counterpart. The associated wear mechanisms were studied through extensive characterisation of...

  • Feature Paper
  • Article
  • Open Access
12 Citations
6,101 Views
14 Pages

Formation of Boundary Film from Ionic Liquids Enhanced by Additives

  • Erik Nyberg,
  • Johanne Mouzon,
  • Mattias Grahn and
  • Ichiro Minami

26 April 2017

Room temperature ionic liquids (RTILs) have several properties that make them interesting candidates as base fluids for extreme conditions. However, a lack of compatibility with tribo-improving additives combined with an often overly aggressive natur...

(This article belongs to the Section Chemical and Molecular Sciences)
  • Article
  • Open Access
6 Citations
3,421 Views
20 Pages

Enhanced Tribological Performance of Low-Friction Nanocomposite WSexSy/NP-W Coatings Prepared by Reactive PLD

  • Vyacheslav Fominski,
  • Dmitry Fominski,
  • Maxim Demin,
  • Roman Romanov and
  • Alexander Goikhman

21 March 2023

A novel laser-based method for producing nanocomposite coatings consisting of a tungsten sulfoselenide (WSexSy) matrix and W nanoparticles (NP-W) was developed. Pulsed laser ablation of WSe2 was carried out in H2S gas under appropriate laser fluence...

(This article belongs to the Special Issue Laser Synthesis and Processing of Nanostructured Materials)
  • Article
  • Open Access
6 Citations
2,145 Views
24 Pages

Tribological Performance of Anti-Wear Coatings on Tools for Forming Aluminium Alloy Sheets Used for Producing Pull-Off Caps

  • Kamil Czapla,
  • Krzysztof Żaba,
  • Marcin Kot,
  • Ilona Nejman and ,
  • Marcin Madej and
  • Tomasz Trzepieciński
  • + 1 author+ 0 author

28 September 2023

Ensuring adequate reliability of the production process of packaging closures has made it necessary to study the effect of annealing and varnishing variants on the strength and structural properties of the stock material. As a test material, EN AW-50...

(This article belongs to the Special Issue Recent Trends in Roughness Measurement and Data Analysis of Machined Surfaces)
  • Article
  • Open Access
12 Citations
5,842 Views
11 Pages

11 June 2019

This work presents the design of a modular ad-hoc fretting fatigue and fretting wear tribotester for thin steel wires. The working principles of the different modules are described, such as the displacement and contact modules. Preliminary studies fo...

(This article belongs to the Special Issue Recent Advances on Fretting Fatigue)
  • Article
  • Open Access
8 Citations
4,744 Views
17 Pages

Evaluating the Tribological Behaviour in Cutting Operations Using a Modified Ball-on-Disc Open Tribotester

  • Belal G Nassef,
  • Florian Pape,
  • Gerhard Poll,
  • Jan Schenzel and ,
  • Benjamin Bergmann and
  • Berend Denkena
  • + 1 author+ 0 author

28 February 2024

Predicting the tribological behaviour in the secondary shear zone in the metal-cutting processes is considered a significant challenge in contemporary research. This work investigated the frictional performance in the secondary shear zone of a planin...

  • Article
  • Open Access
26 Citations
3,841 Views
16 Pages

3 May 2020

Ball burnishing appears to be a very promising approach for reducing surface height, generating compressive residual stresses and increasing hardness. Ball burnishing treatment was carried out using a Haas CNC Vertical Mill Center VF-1 equipped with...

(This article belongs to the Special Issue Tribology: Friction and Wear of Engineering Materials)
  • Article
  • Open Access
7 Citations
2,042 Views
19 Pages

Effect of Countersample Coatings on the Friction Behaviour of DC01 Steel Sheets in Bending-under-Tension Friction Tests

  • Tomasz Trzepieciński,
  • Krzysztof Szwajka,
  • Marek Szewczyk,
  • Marek Barlak and
  • Joanna Zielińska-Szwajka

23 July 2024

The aim of this article is to provide an analysis of the influence of the type of hard anti-wear coatings on the friction behaviour of DC01 deep-drawing steel sheets. DC01 steel sheets exhibit high formability, and they are widely used in sheet metal...

(This article belongs to the Special Issue Advances in Metal Coatings for Wear and Corrosion Applications)
  • Feature Paper
  • Article
  • Open Access
11 Citations
2,642 Views
18 Pages

Microwave Synthesis of Molybdenum Disulfide Nanoparticles Using Response Surface Methodology for Tribological Application

  • Thachnatharen Nagarajan,
  • Mohammad Khalid,
  • Nanthini Sridewi,
  • Priyanka Jagadish and
  • Rashmi Walvekar

27 September 2022

We used response surface methodology (RSM) based on the central composite design (CCD) model to optimize the synthesis time and temperature of the molybdenum disulfide (MoS2) nanoparticles using the flexiWAVE microwave. Furthermore, the synthesized M...

(This article belongs to the Section Nanocomposite Materials)
  • Article
  • Open Access
30 Citations
4,068 Views
10 Pages

25 March 2020

18Ni(300) maraging steel, which has exceptional strength and toughness, is used in the field of aviation and aerospace. In this paper, using a high-speed tribo-tester, tribological behaviors of 18Ni(300) maraging steel were investigated under high-sp...

  • Article
  • Open Access
45 Citations
9,267 Views
9 Pages

21 October 2015

Environmentally friendly multipurpose grease formulation has been synthesized by using Jatropha vegetable residual oil with lithium soap and multifunctional additive. The thus obtained formulation was evaluated for its tribological performance on a...

(This article belongs to the Special Issue Lubricating Greases)
  • Article
  • Open Access
20 Citations
5,948 Views
15 Pages

Influence of Water on Tribolayer Growth When Lubricating Steel with a Fluorinated Phosphonium Dicyanamide Ionic Liquid

  • Luigi A. Urtis,
  • Andrea Arcifa,
  • Peng Zhang,
  • Junxiao Du and ,
  • Marzia Fantauzzi,
  • Daniel Rauber,
  • Rolf Hempelmann,
  • Tobias Kraus,
  • Antonella Rossi and
  • Nicholas D. Spencer
  • + 5 authors+ 0 author

This work aims to elucidate the role of environmental humidity on the tribological behavior of steel surfaces lubricated with an ionic liquid comprised of a fluorinated phosphonium cation—tributyl-3,3,4,4,5,5,6,6,7,7,8,8,8-tridecafluoro-octyl-phospho...

(This article belongs to the Special Issue Ionic Liquids: Friction and Lubrication Mechanisms)
  • Communication
  • Open Access
6 Citations
2,422 Views
8 Pages

Tribological Performance of Porous Ti–Nb–Ta–Fe–Mn Alloy in Dry Condition

  • Carolina Guerra,
  • Magdalena Walczak,
  • Mamié Sancy,
  • Carola Martínez and ,
  • Claudio Aguilar and
  • Marek Kalbarczyk
  • + 1 author+ 0 author

23 July 2020

The tribological properties of a novel porous Ti–Nb–Ta–Fe–Mn alloy with 0%, 30%, and 60% porosity were evaluated for biomedical applications. The tribotesting was performed using a ball-on-disc under dry conditions, using an a...

(This article belongs to the Special Issue Structure and Mechanical Properties of Alloys)
  • Review
  • Open Access
74 Citations
15,346 Views
62 Pages

A Comprehensive Review of Water-Based Nanolubricants

  • Afshana Morshed,
  • Hui Wu and
  • Zhengyi Jiang

10 September 2021

Applying nanomaterials and nanotechnology in lubrication has become increasingly popular and important to further reduce the friction and wear in engineering applications. To achieve green manufacturing and its sustainable development, water-based na...

(This article belongs to the Special Issue Advances in Water-Based Nanolubricants)
  • Article
  • Open Access
22 Citations
4,123 Views
19 Pages

The high-temperature superlubricity performances of h-BN coatings on the nontextured and textured surface of an Inconel X750 alloy is reported in the present paper. The hardness and bond strength of the h-BN coating and alloy were investigated. The t...

(This article belongs to the Special Issue Green Tribology: New Insights toward a Sustainable World 2023)
  • Article
  • Open Access
33 Citations
4,689 Views
14 Pages

Lubrication Performance of Graphene as Lubricant Additive in 4-n-pentyl-4′-cyanobiphyl Liquid Crystal (5CB) for Steel/Steel Contacts

  • Zhiliang Li,
  • Chonghai Xu,
  • Guangchun Xiao,
  • Jingjie Zhang and ,
  • Zhaoqiang Chen and
  • Mingdong Yi
  • + 1 author+ 0 author

26 October 2018

The lubrication performance of graphene used as additive in 4-n-pentyl-4′-cyanobiphyl liquid crystal (5CB) for steel/steel contacts was studied on a ball-on-plate tribotester. The friction test results show that when the graphene content in the...

(This article belongs to the Section Carbon Materials)
  • Article
  • Open Access
6 Citations
2,326 Views
16 Pages

6 June 2022

This work aims to determine and select the suitable friction stir processing parameters for recycled aluminum alloy 6063 surface composites reinforced with titanium dioxide for better tribological performance. A medium range of processing parameters...

(This article belongs to the Special Issue Surface Modification of Metallic Materials for Wear and Fatigue)
  • Article
  • Open Access
45 Citations
5,743 Views
11 Pages

Wear and Friction Analysis of Brake Pad Material Using Natural Hemp Fibers

  • Mithul Naidu,
  • Ajit Bhosale,
  • Yashwant Munde,
  • Sachin Salunkhe and
  • Hussein Mohamed Abdelmoneam Hussein

30 December 2022

Non-exhaust brake dust and pollution arising from metal, semi-metal, and ceramic brake pads have made recent research consider their replacement by potential natural fibers such as hemp, flax, sisal, etc. These natural fibers are lightweight, biodegr...

(This article belongs to the Section Polymer Analysis and Characterization)
  • Proceeding Paper
  • Open Access
2 Citations
3,165 Views
6 Pages

Experimental Study on Galling Behavior in Aluminum Stamping Processes

  • Heli Liu,
  • Xiao Yang,
  • Yang Zheng and
  • Liliang Wang

Aluminum stamping processes are extensively used in automotive and aviation manufacturing for fabricating lightweight components, but their qualities are often restricted by galling, an adhesive wear phenomenon that causes the aluminum transfer and a...

(This article belongs to the Proceedings of The 19th International Conference on Experimental Mechanics)
  • Article
  • Open Access
14 Citations
2,540 Views
12 Pages

Preparation, Mechanical Properties, and High-Temperature Wear Resistance of Ti–Al–B alloy

  • Gongjun Cui,
  • Yanping Liu,
  • Guijun Gao,
  • Huiqiang Liu and ,
  • Sai Li and
  • Ziming Kou
  • + 1 author+ 0 author

14 November 2019

Ti–Al matrix alloy reinforced with a high content of boron was fabricated by using a high-temperature alloying method and powder metallurgy technique (P/M). The preparation method of Ti–Al–B alloying powder was put forward. Phases,...

  • Feature Paper
  • Article
  • Open Access
15 Citations
3,886 Views
16 Pages

Friction Reduction in Unidirectional Lubricated Sliding Due to Disc Surface Texturing

  • Slawomir Wos,
  • Waldemar Koszela,
  • Andrzej Dzierwa and
  • Pawel Pawlus

29 February 2020

Surface texturing is an option of surface engineering resulting in reduction of friction due to the creation of isolated dimples or grooves on sliding surfaces. The purpose of this work is to find the effect of the groove bottom profiles on the reduc...

(This article belongs to the Special Issue Tribological Behavior of Functional Surface: Models and Methods)
  • Article
  • Open Access
10 Citations
4,677 Views
10 Pages

In the present paper, the influence of self-mated friction materials on the tribological properties of hydrogenated amorphous silicon films (a-Si:H films) is studied systemically at high temperature. The results are obtained by comparing the tribolog...

(This article belongs to the Special Issue Science and Technology of Thermal Barrier Coatings)
  • Article
  • Open Access
8 Citations
5,028 Views
13 Pages

Friction Performance of Aluminum-Silicon Alloy Cylinder Liner after Chemical Etching and Laser Finishing

  • Fengming Du,
  • Chengdi Li,
  • Zetian Mi,
  • Ruoxuan Huang and ,
  • Xiaoguang Han,
  • Yan Shen and
  • Jiujun Xu
  • + 2 authors+ 0 author

11 April 2019

In order to enhance the surface friction performance of the aluminum-silicon (Al-Si) alloy cylinder liner, chemical etching and laser finishing techniques are applied to improve the friction performance. The cylinder liner samples are worn against a...

  • Article
  • Open Access
3 Citations
3,214 Views
21 Pages

Tribological Performance of a Composite Cold Spray for Coated Bores

  • Eduardo Tomanik,
  • Laurent Aubanel,
  • Michael Bussas,
  • Francesco Delloro and
  • Thomas Lampke

The tribological performance of a thermal sprayed, mirror-like surface with localized protuberances was investigated through tribotests and computational simulation. A composite coating with a 410L steel matrix and M2 tool steel hard particles was ap...

(This article belongs to the Special Issue Tribology in Mobility, Volume II)
  • Article
  • Open Access
12 Citations
2,678 Views
17 Pages

10 February 2022

This work aims to optimize the friction stir processing parameters of recycled aluminum alloy 6063 for enhanced mechanical and tribological properties. The selected friction stir processing parameters that were used to produce friction stir processed...

(This article belongs to the Special Issue Surface Modification of Metallic Materials for Wear and Fatigue)
  • Article
  • Open Access
15 Citations
5,014 Views
15 Pages

The Lubricity of Ternary Fuel Mixture Blends as a Way to Assess Diesel Engine Durability

  • Abul Kalam Azad,
  • Mohammad Golam Rasul,
  • Subhash Chandra Sharma and
  • Mohammad Masud Kamal Khan

24 December 2017

The study deals with the lubrication characteristics of ternary fuel mixture blends to assess diesel engine durability by using better performing fuels, namely Mandarin Crambe and Paraffin (ManCr_Pa) and Avocado Bush nut and Paraffin (AvBn_Pa). Tribo...

(This article belongs to the Collection Bioenergy and Biofuel)
  • Article
  • Open Access
12 Citations
3,791 Views
13 Pages

Anti-Wear Property of Aluminum–Silicon Alloy Treated by Chemical Etching, Mechanical Honing and Laser Finishing

  • Fengming Du,
  • Chengdi Li,
  • Zetian Mi,
  • Yan Shen and ,
  • Ruoxuan Huang,
  • Xiaoguang Han,
  • Yong Dong and
  • Jiujun Xu
  • + 3 authors+ 0 author

18 April 2019

To enhance the anti-wear property of aluminum–silicon (Al–Si) alloy, three processing technologies—chemical etching, mechanical honing and laser finishing—were compared in terms of their effects on anti-wear performance. The t...

(This article belongs to the Special Issue Tribology of Materials and Analysis)
  • Article
  • Open Access
12 Citations
4,181 Views
19 Pages

Tribochemical Interactions between Carbon Nanotubes and ZDDP Antiwear Additive during Tribofilm Formation on Uncoated and DLC-Coated Steel

  • Wojciech Dzięgielewski,
  • Joanna Kowalczyk,
  • Andrzej Kulczycki,
  • Monika Madej and
  • Dariusz Ozimina

23 May 2020

The data from the authors’ earlier investigations show that molecules of zinc dithiophosphate (ZDDP) added to a lubricant can absorb energy emitted by a solid surface, which is where triboreactions occur. If the lubricant contains structures ab...

(This article belongs to the Special Issue Tribology: Friction and Wear of Engineering Materials)
  • Article
  • Open Access
11 Citations
4,285 Views
19 Pages

Tribology of Polymer Blends PBT + PTFE

  • Constantin Georgescu,
  • Lorena Deleanu,
  • Larisa Chiper Titire and
  • Alina Cantaragiu Ceoromila

20 February 2021

This paper presents results on tribological characteristics for polymer blends made of polybutylene terephthalate (PBT) and polytetrafluoroethylene (PTFE). This blend is relatively new in research as PBT has restricted processability because of its p...

(This article belongs to the Special Issue Polymer Composites for Tribological Applications)
  • Article
  • Open Access
56 Citations
7,842 Views
10 Pages

Preparation and Tribological Properties of WS2 Hexagonal Nanoplates and Nanoflowers

  • Xianghua Zhang,
  • Jiangtao Wang,
  • Hongxiang Xu,
  • Heng Tan and
  • Xia Ye

This paper presents the facile synthesis of two different morphologies of WS2 nanomaterials—WS2 hexagonal nanoplates and nanoflowers—by a sulfurization reaction. The phases and morphology of the samples were investigated by X-ray diffract...

(This article belongs to the Special Issue Preparation and Properties of 2D Materials)
  • Article
  • Open Access
13 Citations
5,590 Views
20 Pages

Effect of Hygrothermal Ageing on Tribological Behaviour of PTFE-Based Composites

  • Mohammad-Reza Homayoun,
  • Arash Golchin and
  • Nazanin Emami

26 November 2018

The present study investigates the influence of hygrothermal ageing on the tribological behaviour of polytetrafluoroethylene (PTFE) polymer composites. Three PTFE composites along with unfilled PTFE were tested in sliding contact against Inconel 625...

  • Article
  • Open Access
9 Citations
3,012 Views
12 Pages

Tribological Properties of Spark Plasma Sintered Al-SiC Composites

  • Beata Leszczyńska-Madej,
  • Marcin Madej and
  • Dariusz Garbiec

4 November 2020

The paper presents the results of research on the tribological properties of spark-plasma-sintered Al-SiC composites. Composites with contents of 50 and 70 wt.% SiC were prepared. The sintering process was carried out using an HP D 25/3 spark plasma...

(This article belongs to the Special Issue Tribology: Friction and Wear of Engineering Materials)

of 2