A new constitutive model for Q235B structural steel is proposed, incorporating the effect of dynamic strain aging. Dynamic strain aging hugely affects the microstructural behavior of metallic compounds, in turn leading to significant alterations in t...
In this study, the evolution of the mechanical properties of Fe–30Mn–9Al–1C steel has been determined in tensile tests at strain rates of 10−4 to 102 s−1. The results show that the strain rate sensitivity becomes a negat...
In this study, the flow stress behavior of ferritic-pearlitic steel (C45E steel) is investigated through isothermal compression testing at different strain rates (1 s−1, 5 s−1, and 60 s−1) and temperatures ranging from 200 to 700 &d...
Austenitic stainless steels similar to type AISI 316L are widely used structural materials in current and future nuclear reactors. Careful development and characterization of these materials and their welds is needed to verify the structural integrit...
The dynamic strain aging (DSA) behavior of an extruded Mg–3Gd–1Zn (wt.%) alloy was investigated under compressive deformation at intermediate temperatures (150–250 °C) and strain rates ranging from 5 × 10−5 to 10&min...
In the study of the liquid metal embrittlement (LME) of the T91/lead-bismuth eutectic (LBE) system, it is observed that LME occurs in a temperature interval which is similar to the temperature range where dynamic strain aging (DSA) is observed. Howev...
In the current study, dynamic strain ageing (DSA) phenomena in 316L austenitic stainless steel was investigated under as-received and as-welded conditions. A tensile test was carried out on as-received and as-welded samples for the temperatures of 25...
As a new treatment process after welding, the process parameters of laser shock peening (LSP) in dynamic strain aging (DSA) temperature regimes can be precisely controlled, and the process is a non-contact one. The effects of LSP at elevated temperat...
This work reports results from quasi-static nanoindentation measurements of iron, in the un-strained state and subjected to 15% tensile pre-straining at room temperature, 125 °C and 300 °C, in order to extract room temperature hardness and el...
An enhancement in fatigue life for ferrite–pearlite low-carbon steel (LCS) at high temperature (HT) has been discovered, where it increased from 190,873 cycles at room temperature (RT) to 10,000,000 cycles at 400 °C under the same stress co...
The extruded Mg–6Bi alloy and Mg–6Bi–1Ag alloy subjected to extrusion at 300 °C with the extrusion ratio of 25:1 and die-exit speed of 2 m/min were used to investigate microstructure characteristics and mechanical behavior. The...
The tensile and low-cycle fatigue properties of a Fe-Ni-based GH1059 superalloy were investigated at room temperature (RT, about 25 °C) in air and at 550 °C in high vacuum. The tensile curve at 550 °C indicated that dynamic strain aging i...
The formability at room temperature and low speed limits the application of aluminum alloy, while high strain rates positively improve the formability of materials. The constitutive behaviors of materials under high strain rates or impact loadings ar...
The paper analyzes the elastoplastic transition in Fe–0.025 wt. % C at a temperature of 296–503 K and strain rate of 6.67·10−6–3.33·10−3 s−1. The analysis shows that the lower yield stress increases b...
The effect of initial texture on slip activity, dynamic recrystallization, and basal texture development was investigated in a Mg–9 wt.% Ag alloy during high-temperature plane strain compression. Three sets of specimens with different initial c...
We studied the Portevin-Le Chatelier effect and fracture behavior of a FeMnC TWIP steel using high speed digital image correlation by varying the specimen geometry (flat vs. round) and test strain rate (0.001 vs. 0.1 s−1). The results show that...
In this study, the effect of interstitial contents on the mechanical properties and strain-induced martensite formation in an austenitic stainless steel was investigated. The mechanical properties of solution annealed Fe-15Cr-7Mn-4Ni-0.5Si-(0.01-0.2)...
The present study intends to assess the ratcheting response of SA508 and SA333 steel alloys subjected to asymmetric loading cycles at various operating temperatures of 298, 573, and 623K through a hardening framework developed by Ahmadzadeh–Var...
The present study intends to evaluate the ratcheting of ER9 wheel medium carbon steel and austenitic steel samples at room and elevated temperatures subjected to uniaxial loading cycles through the use of the Ahmadzadeh–Varvani (A–V) kine...
In this study, we comparatively investigate the low cycle fatigue behavior of Alloy 617 (INCONEL 617) weldments by gas tungsten arc welding process at room temperature and 800 °C in the air to support the qualification in high temperature application...
Machining process modeling has been an active endeavor for more than a century and it has been reported to be able to predict industrially relevant process outcomes. Recent advances in the fundamental understanding of material behavior and material m...
Inconel 625 is a nickel-based alloy that is mainly used in high-temperature applications. Inconel 625 exhibits an unstable plastic flow at elevated temperatures characterized by serrated yielding, well-known as the Portevin-Le Chatelier effect. The e...
Serrated flow effects are visible on a metal surface even after coating. Thus, they are undesirable to manufacturers and product users. To meet the expectations of the industry, research on the conditions for serrated flow occurrence in 5019 aluminum...
Since Ni-based single-crystal superalloys are anisotropic materials, their behavior in different crystal orientations is of great interest. In this study, the yielding behavior in both tension and compression for...
A thermo-mechanical treatment (TMT) at the temperature of maximum dynamic strain aging has been optimized and performed on quenched and tempered steel SAE4140H (German designation: 42CrMo4) in order to improve the fatigue limit in the high cycle fati...
The strain hardening and damage behavior of Al-added twinning induced plasticity (TWIP) steels were investigated. The study was focused on comparing two different alloying concepts by varying C and Mn contents with stacking fault energy (SFE) values...
Serrated flow and work-hardening behavior (by Voce equation) of China low activation martensitic (CLAM) steel were investigated in the temperature range of 300–923 K (27 °C to 650 °C). The steel exhibited serrated flow at intermediate t...
The development of FeCrAl alloys has commenced for use as nuclear fuel cladding material, intended to serve as an enhanced accident-tolerant alternative to Zr-based alloys. In this study, the Fe-13Cr-4Al alloy, specifically designed for advanced acci...
This study investigates the mechanical behavior and deformation mechanisms of Fe-30Mn-0.05C (30Mn0.05C) and Fe-34Mn-0.7C (34Mn0.7C) steels at room temperature (RT) and liquid nitrogen temperature (LNT). The 30Mn0.05C sample exhibited a significant en...
The mechanical behavior of S135 and V150 (Mo-V-Nb microalloyed) drill pipe steels was systematically investigated at room temperature (RT) and elevated temperatures (100–300 °C), alongside the microstructural evolution after long-term therm...
In this study, two vineyards of different age were chosen. During three years, a sampling campaign was performed for isolating vineyard-associated Saccharomyces cerevisiae (S. cerevisiae) strains. Bark portions and, when present, grape bunches were r...
The Portevin-Le Châtelier (PLC) effect in a powder metallurgy (PM) Co-Ni-based superalloy was systematically investigated via the tensile tests at temperatures ranging from 200 to 600 °C and strain rates at 1.0 × 10−4 to 1.0 &ti...
Temperature- and strain-rate-dependent serrated flow, localized plastic instability, and qualitative microcrack evolution in Mn13 Hadfield steel were investigated using stress–strain analysis and in situ tensile observation. Solution treatment...
We have developed a self-consistent model for predicting the velocity of 1/2[111] screw dislocation in binary iron–carbon alloys gliding by a high-temperature Peierls mechanism. The methodology of modelling includes: (i) Kinetic Monte-Carlo (kM...
The Portevin–Le Châtelier (PLC) effect often results in serrated plastic flow during tensile testing of aluminum alloys. Its magnitude and characteristics are often sensitive to a material’s heat treatment condition and to the applied strain rate and...
This article is focused on the mechanical behavior and its relationship with the microstructural changes observed in two high-manganese steels presenting twinning-induced plasticity (TWIP) and transformation-induced plasticity (TRIP), namely Steel B...
The paper reviews the recent works concerning the Portevin–Le Chatelier (PLC) effect in Advanced High-Strength Steels (AHSSs) with a special attention to high-strength medium-manganese steels. Theories explaining the mechanism of the plastic in...
The dynamic tensile behavior of the twinning-induced plasticity (TWIP) steel with the vanadium carbide is investigated at different strain rates of 10−4, 10−3, 10−2 and 0.05 s−1. Microstructure characterization, carried out us...
Epoxy polymer concrete (EPC) is widely applied in engineering for its excellent mechanical properties. The impact loads and severe climatic conditions such as ultraviolet radiation, temperature change and rain erosion are in general for its engineeri...
This study examined the effects of heat treatment on the microstructure and dynamic deformation characteristics of AA2519 aluminum alloy in T4, T6, and T8 tempers under high strain rates of 1000–4000 s−1. A Split Hopkinson pressure bar (S...
Hydroxyl terminated polybutadiene (HTPB) coating is widely used in a solid rocket motor, but an aging phenomenon exists during long-term storage, which causes irreversible damage to the performance of this HTPB coating. In order to study the effect o...
This study investigated the small-strain dynamic properties of expanded polystyrene (EPS) lightweight soil (ELS), a low-density geosynthetic material used to stabilize slopes and alleviate the subgrade settlement of soft soil. Resonant column tests w...
The dynamic behaviour of high-volume fly ash concrete with nano-silica (HVFANS) and polypropylene fibres at curing ages of 7 to 90 days was determined by using a split Hopkinson pressure bar (SHPB) machine. At each curing age, the concrete samples we...
The effects of oxidative aging on the static and dynamic properties of nitrile rubber at the molecular scale were investigated by molecular dynamics simulation. The aged nitrile rubber models were constructed by introducing hydroxyl groups and carbon...
Unsaturated polyester polymer concrete (UPPC) is a promising rapid repair material for pavement engineering, while the age-dependent and rate-dependent bonding behaviors between UPPC and ordinary Portland concrete (OPC) substrate remains poorly under...
The longitudinal compressive behavior of the three-dimensional four-step braided composites after cyclic hygrothermal aging was investigated using a split Hopkinson pressure bar (SHPB) apparatus under high strain rates (1100~1250 s−1, 1400~1600...
Iron-based SMAs can be used in the medical field for both their shape memory effect (SME) and biodegradability after a specific period, solving complicated chirurgical problems that are partially now addressed with shape-memory polymers or biodegrada...
This work studied the high strain rate behavior of the Ti-4Al-5Mo-5V-5Cr-1Nb (Ti-45551) alloy after two-stage aging, with dynamic tension tests conducted using the split Hopkinson tensile bar. The results show that the microstructure, especially the...
In this article, a mathematical model of the wire’s average temperature change in the process of multiple drawing on high-speed straight-line drawing machines has been developed. The calculation results showed that the average temperature of th...
This study focuses on the dynamic compression performance of corroded steel fiber-reinforced concrete (SFRC) exposed to drying–wetting chloride cycles by a 37 mm diameter split Hopkinson pressure bar (SHPB) system. Three steel fiber contents (0.5%, 1...
of 8