Skip to Content

10,648 Results Found

  • Article
  • Open Access
23 Citations
5,304 Views
14 Pages

14 January 2019

Predicting and controlling process-induced deformation of composites during cure can play a significant role in ensuring the accuracy of manufacture and assembly of composite structures. In this paper the parametric investigation on the process-induc...

  • Article
  • Open Access
15 Citations
4,235 Views
9 Pages

29 July 2019

A magnesium alloy was fabricated through the consolidation of chips accumulated during the turning process, followed by cold compaction and hot extrusion. A variation in the depths of cut was done during turning to understand the effect of deformatio...

  • Article
  • Open Access
8 Citations
3,793 Views
19 Pages

Shape Analysis of the Elastic Deformation Region throughout the Axi-Symmetric Wire Drawing Process of ETP Grade Copper

  • Paweł Strzępek,
  • Andrzej Mamala,
  • Małgorzata Zasadzińska,
  • Grzegorz Kiesiewicz and
  • Tadeusz Antoni Knych

20 August 2021

The wire drawing process is commonly perceived as one of the best studied metal forming processes in almost every aspect; however, when considering elastic deformation, researchers usually focus on the uniaxial tensile forces after the material exits...

(This article belongs to the Special Issue Commemorating the Launch of the Section 'Metals and Alloys')
  • Review
  • Open Access
18 Citations
5,047 Views
53 Pages

11 December 2024

Titanium (Ti) and its alloys are used in various applications, including aircraft frames, ship parts, heat exchangers, and evaporator tubes, because of their extraordinary properties, such as high specific strength, excellent corrosion resistance at...

(This article belongs to the Section Metals and Alloys)
  • Article
  • Open Access
1 Citations
5,041 Views
15 Pages

30 October 2019

Wrinkling of beverage cans is one of the problems faced by can manufacturers and aluminum suppliers. The bottom of an aluminum can is wrinkled by compression during the forming process. In this study, to predict the occurrence of wrinkles during the...

  • Article
  • Open Access
21 Citations
4,168 Views
13 Pages

11 October 2020

Residual stresses are generated by tool-part interaction due to the large difference in the coefficients of thermal expansion (CTE) between the tool and the composite part, resulting in more process-induced part deformation. In this paper, a 3-D nume...

  • Article
  • Open Access
14 Citations
6,548 Views
15 Pages

18 November 2019

The orbital riveting process has been successively adopted in the assembly of wheel hub bearing, due to its special merits of high efficiency, low cost, and so on. The forming process and deformation behavior of the inner ring have significant influe...

(This article belongs to the Special Issue Advanced Metal Forming Processes)
  • Feature Paper
  • Review
  • Open Access
5 Citations
2,972 Views
11 Pages

In recent times, an alternative synthesis pathway involving severe plastic deformation for Mg-based materials has been explored involving the generation of turnings according to a set of machining parameters and cold compaction into billets followed...

  • Article
  • Open Access
9 Citations
4,394 Views
18 Pages

21 October 2019

With the rapid development of modern aviation industry, dual-property turbine disc with fine comprehensive performance plays an important role in raising the thrust-to-weight ratio of the aero-engine. For manufacturing dual-property turbine disc, the...

(This article belongs to the Special Issue The Behaviours of Alloys under Thermo-Mechanical Treatment)
  • Article
  • Open Access
9 Citations
2,705 Views
22 Pages

Microstructure Evolution and Deformation Mechanisms of As-Cast Antibacterial Ti6Al4V-5Cu Alloy for Isothermal Forging Process

  • Solomon Kerealme Yeshanew,
  • Chunguang Bai,
  • Qing Jia,
  • Tong Xi and ,
  • Zhiqiang Zhang,
  • Diaofeng Li,
  • Zhizhou Xia,
  • Rui Yang and
  • Ke Yang
  • + 4 authors+ 0 author

6 May 2022

The hot workability behavior of antibacterial Ti6Al4V-5Cu alloy was investigated using a hot compression experiment in the temperature range of 790–1040 °C and strain rate of 10−3–10 s−1 with a strain of 0.4. The deformation behavior of the alloy was...

  • Article
  • Open Access
10 Citations
3,233 Views
19 Pages

Hot Deformation Behavior and Simulation of Hot-Rolled Damage Process for Fine-Grained Pure Tungsten at Elevated Temperatures

  • Yongqi Lv,
  • Siqi Zhao,
  • Tao Liu,
  • Huichao Cheng and ,
  • Jinglian Fan and
  • Yuanchun Huang
  • + 1 author+ 0 author

20 November 2022

Fine-grained pure tungsten fabricated by a sol drying reduction low-temperature sintering method and hot isothermal compression tests were performed by using the Gleeble 3800 thermo mechanical simulator at deformation temperatures from 1273 K to 1473...

(This article belongs to the Special Issue Advanced Manufacturing of Metals and Composites: Effect of Processes on Microstructure and Mechanical Properties)
  • Article
  • Open Access
2 Citations
1,713 Views
15 Pages

Influence of Process Liquids on the Formation of Strengthened Nanocrystalline Structures in Surface Layers of Steel Parts during Thermo-Deformation Treatment

  • Ihor Hurey,
  • Andy Augousti,
  • Pavlo Maruschak,
  • Alan Flowers and ,
  • Volodymyr Gurey,
  • Volodymyr Dzyura and
  • Olegas Prentkovskis
  • + 2 authors+ 0 author

9 September 2024

The results of the influence of a range of process liquids on the formation of strengthened nanocrystalline structures in the surface layers of steel samples with different carbon content during thermo-deformation treatment are presented. The liquids...

(This article belongs to the Section Materials Science and Engineering)
  • Article
  • Open Access
527 Views
18 Pages

Rutting and moisture-induced damage are critical challenges for asphalt pavements in tropical regions such as Vietnam, where high temperatures and heavy traffic accelerate permanent deformation. This study aims to evaluate the rutting performance, de...

(This article belongs to the Special Issue Surface Protection of Pavements: New Perspectives and Applications)
  • Article
  • Open Access
116 Views
16 Pages

Phased Array Antenna Surface Deformation Reconstruction Based on Modal Low-Rank Correction and Gaussian Process Data Migration

  • Yuefei Yan,
  • Shengqi Pan,
  • Yafan Qin,
  • Yan Wang and ,
  • Shikun Zheng,
  • Jingtan Chen,
  • Song Xue,
  • Zhihai Wang,
  • Kunpeng Yu and
  • Congsi Wang
  • + 5 authors+ 0 author

12 November 2026

Deformation of a phased array antenna surface can degrade its electrical performance. Conventional modal reconstruction depends on the accuracy of the structural model, while purely data-driven methods require extensive experimental data. We propose...

(This article belongs to the Section E: Engineering and Technology)
  • Article
  • Open Access
7 Citations
2,048 Views
12 Pages

18 July 2024

Continuous fiber-reinforced composites are increasingly used in industry for their superior specific modulus and strength. The curing process-induced deformation (PID) has been a critical problem during manufacturing, which always exhibits dispersed...

(This article belongs to the Section Carbon Materials)
  • Article
  • Open Access
733 Views
22 Pages

8 December 2025

To ensure the sustainability of mining activities, it is imperative to effectively manage their environmental impacts, particularly geological hazards. Mining areas feature fragile geological environments subject to intense engineering disturbances,...

(This article belongs to the Special Issue Mineral Resource Utilization and GeoConservation for Sustainable Development)
  • Article
  • Open Access
5 Citations
2,027 Views
18 Pages

6 October 2023

For this study, the geological engineering features and possible failure modes of the Dabenliu quarry slope in the Jinping-I Hydropower Station were qualitatively analyzed before a method for setting viscous boundary and an algorithm for modeling pre...

(This article belongs to the Special Issue Advances in Failure Mechanism and Numerical Methods for Geomaterials)
  • Article
  • Open Access
8 Citations
2,037 Views
22 Pages

3 November 2024

The process-induced deformation (PID) during the manufacturing of thermosetting composite materials can significantly compromise manufacturing precision. This paper introduces an innovative method that combines a finite element analysis (FEA), featur...

(This article belongs to the Section Composites Modelling and Characterization)
  • Article
  • Open Access
7 Citations
2,137 Views
11 Pages

Fractional Model of the Deformation Process

  • Olga Sheremetyeva and
  • Boris Shevtsov

The article considers the fractional Poisson process as a mathematical model of deformation activity in a seismically active region. The dislocation approach is used to describe five modes of the deformation process. The change in modes is determined...

(This article belongs to the Special Issue Fractional Calculus and Fractals in Mathematical Physics)
  • Article
  • Open Access
962 Views
14 Pages

20 April 2026

The article discusses the methods for classifying processes for testing and processing metals by plastic deformation, based on the characteristics of their stress–strain state. The basic methods for determining the stress and strain states usin...

(This article belongs to the Special Issue Deformation of Metals and Alloys: Theory, Simulations and Experiments—2nd Edition)
  • Article
  • Open Access
12 Citations
2,671 Views
16 Pages

Hot Deformation Behavior and Processing Map of GH901 Superalloy

  • Rui Ma,
  • Lulu Li,
  • Ruixue Zhai,
  • Xiangnan Meng and
  • Jun Zhao

10 November 2021

During the forging process GH901 superalloys easily produce cracks and defects, such as coarse crystals in tissues, which affect the performance of the alloy. Using GH901 nickel-based alloy, high-temperature compression tests at deformation temperatu...

(This article belongs to the Topic Single-Crystal Ni-Based Alloys)
  • Article
  • Open Access
1 Citations
1,617 Views
16 Pages

Study on Thermal Deformation Behavior and Thermal Processing Map of a New Al-Li Alloy

  • Daoqi Chen,
  • Xinyang Han,
  • Yinggan Zhang,
  • Yan Liu and
  • Junfeng Chen

30 April 2025

As a representative third-generation Al-Li alloy, 2A97 alloy has attracted significant attention for applications in aeronautics and astronautics, but its poor hot workability and complex thermal deformation behavior, which make for difficult optimiz...

(This article belongs to the Special Issue Microstructure and Properties of Metals and Alloys)
  • Article
  • Open Access
1 Citations
2,436 Views
22 Pages

Bayesian Modeling for Nonstationary Spatial Point Process via Spatial Deformations

  • Dani Gamerman,
  • Marcel de Souza Borges Quintana and
  • Mariane Branco Alves

11 August 2024

Many techniques have been proposed to model space-varying observation processes with a nonstationary spatial covariance structure and/or anisotropy, usually on a geostatistical framework. Nevertheless, there is an increasing interest in point process...

(This article belongs to the Special Issue Bayesianism)
  • Article
  • Open Access
30 Citations
4,546 Views
17 Pages

Hot Deformation Characteristics—Constitutive Equation and Processing Maps—of 21-4N Heat-Resistant Steel

  • Yiming Li,
  • Hongchao Ji,
  • Wangda Li,
  • Yaogang Li and ,
  • Weichi Pei and
  • Jinping Liu
  • + 1 author+ 0 author

27 December 2018

The hot deformation behavior of 21-4N heat-resistant steel was studied by hot compression test in a deformation temperature range of 1000–1180 °C, a strain rate range of 0.01–10 s−1 and a deformation degree of 60%, and the stres...

  • Article
  • Open Access
8 Citations
4,340 Views
18 Pages

12 June 2020

The flow behavior of a new kind of high-strength nickel brass used as automobile synchronizer rings was investigated by hot compression tests with a Gleeble-3500 isothermal simulator at strain rates ranging from 0.01 to 10 s−1 and a wide deform...

(This article belongs to the Special Issue High-Temperature Behavior of Metals)
  • Article
  • Open Access
7 Citations
2,965 Views
12 Pages

Hot-Deformation Behavior and Processing Maps of a Low-Carbon Fe-2 wt% Nb Steel

  • Wentao Luo,
  • Pengzhan Cai,
  • Ziyong Hou,
  • Yuhui Wang and ,
  • Ling Zhang and
  • Guilin Wu
  • + 1 author+ 0 author

30 November 2021

In the present work, the deformation behavior and processing maps of a low-carbon Fe-2 wt% Nb steel were studied by means of hot-compression tests at temperatures of 800–1150 °C and strain rates of 0.01–10 s−1. The hot-processin...

(This article belongs to the Section Crystallography and Applications of Metallic Materials)
  • Article
  • Open Access
11 Citations
2,705 Views
19 Pages

28 July 2022

With higher creep strength and heat resistance, 34CrNi3Mo has been widely used in the production of engine rotors, steam turbine impellers, and turbine blades. To investigate the hot deformation behaviors of 34CrNi3Mo steel, hot compressive tests wer...

(This article belongs to the Section Metals and Alloys)
  • Article
  • Open Access
23 Citations
4,023 Views
19 Pages

21 June 2020

With the development of the aviation industry, the performance requirements of materials for aviation large-scale structural parts are getting higher and higher. Ti-6554 alloy is the material of choice for aviation large-scale structural parts, but i...

(This article belongs to the Special Issue Titanium Alloys and Titanium-Based Matrix Composites)
  • Article
  • Open Access
5 Citations
2,131 Views
12 Pages

4 December 2024

It is important to explore the hot deformation behavior and establish the hot processing map of steel to design and optimize the hot rolling process. In this paper, 50CrVA spring steel was used as the experimental material. Single-pass compression te...

(This article belongs to the Special Issue Research on Microstructure and Performance Mechanisms of Advanced Steels and Alloys)
  • Article
  • Open Access
3 Citations
2,395 Views
13 Pages

Hot Deformation Behavior and Processing Maps of ZnSnO3/Cu Composites

  • Wei-Jian Li,
  • Zi-Yao Chen,
  • Xiao-Peng Tang,
  • Wen-Zhu Shao and
  • Liang Zhen

21 October 2022

In this work, we designed ternary ZnSnO3 particle-reinforced Cu matrix composites and evaluated the hot deformation behavior of ZnSnO3/Cu composites. The hot deformation characteristics of typical dynamic recrystallization were probed by the resultin...

(This article belongs to the Section Metals and Alloys)
  • Article
  • Open Access
4 Citations
2,496 Views
17 Pages

Hot Deformation Behavior and Processing Maps of 26CrMo7S Steel Used in Oil Exploration

  • Hemiao Jiang,
  • Hongying Li,
  • Dianyuan Huang,
  • Yinghui Zhao and ,
  • Jiwen Liu,
  • Qing Gao,
  • Hang He and
  • Ximao Liu
  • + 3 authors+ 0 author

6 November 2023

The hot deformation behavior and flow stress characteristics of experimental 26CrMo7S steel were analyzed using a thermal simulator under a range of conditions, including a strain rate range of 0.01~10 s−1, a temperature range of 850~1250 °...

(This article belongs to the Special Issue Advanced Metal Matrix Functional Composites and Applications)
  • Article
  • Open Access
207 Views
13 Pages

Hot Deformation Behavior, Constitutive Model, and Processing Map of 022Cr12Ni10MoTi Alloy

  • Xiuxuan Yang,
  • Wanhua Chen,
  • Changjun Wang,
  • Jianxiong Liang and
  • Chengguo Yu

29 September 2026

This study investigates the hot deformation behavior of 022Cr12Ni10MoTi alloy over a wide range of strain rates and temperatures. Hot compression experiments were carried out at deformation temperatures ranging from 900 °C to 1200 °C and stra...

(This article belongs to the Section Metals and Alloys)
  • Feature Paper
  • Article
  • Open Access
11 Citations
2,185 Views
17 Pages

27 June 2023

Fe-Al-Ta alloys are expected to replace high-alloyed steels in steam turbine blades. However, the mechanical properties of the forged blades are still not optimal due to limited grain refinement during hot forging and the coarse-grained microstructur...

(This article belongs to the Special Issue Thermomechanical Treatment of Metals and Alloys)
  • Article
  • Open Access
89 Citations
9,190 Views
22 Pages

Semi-Automatic Identification and Pre-Screening of Geological–Geotechnical Deformational Processes Using Persistent Scatterer Interferometry Datasets

  • Roberto Tomás,
  • José Ignacio Pagán,
  • José A. Navarro,
  • Miguel Cano and ,
  • José Luis Pastor,
  • Adrián Riquelme,
  • María Cuevas-González,
  • Michele Crosetto,
  • Anna Barra and
  • Nicola Casagli
  • + 18 authors+ 13 authors

14 July 2019

This work describes a new procedure aimed to semi-automatically identify clusters of active persistent scatterers and preliminarily associate them with different potential types of deformational processes over wide areas. This procedure consists of t...

(This article belongs to the Section Remote Sensing in Geology, Geomorphology and Hydrology)
  • Article
  • Open Access
966 Views
30 Pages

13 August 2026

This study devised a blasting experiment to establish a dynamic quantified relationship between blasting and movement, failure, and ejection of rock masses. The experiment was conducted using the 3D digital image correlation method (3D-DIC), which pr...

(This article belongs to the Special Issue Numerical Simulation and Engineering Application of Rock Mechanics and Geotechnical Engineering (Second Edition))
  • Article
  • Open Access
1 Citations
848 Views
14 Pages

Hot Deformation Behavior and Processing Map of 25Cr2Ni2MoV Steel

  • Yong Wang,
  • Yanwu Dong,
  • Zhouhua Jiang,
  • Lev Medovar and
  • Ganna Stovpchenko

10 February 2026

This study investigates the hot deformation behavior of electroslag remelted (ESR) 25Cr2Ni2MoV steel, focusing on the effects of deformation temperature and strain rate on flow stress, microstructure evolution, and dynamic recrystallization (DRX) mec...

  • Article
  • Open Access
9 Citations
2,752 Views
18 Pages

Hot Deformation Behavior Coordination and Processing Maps of 40Cr/Q345B Bimetallic Blank by Centrifugal Casting

  • Yanlong Jia,
  • Huiping Qi,
  • Mengmeng Pei,
  • Zhenjiang Li and ,
  • Fangcheng Qin and
  • Lu Jia
  • + 1 author+ 0 author

29 July 2022

The compact cast-rolling compound forming of bimetallic ring is an efficient process for manufacturing large bimetallic rings. The difference in hot deformation behavior of the two metals directly affects the coordinated deformation of bimetals durin...

  • Review
  • Open Access
9 Citations
7,019 Views
22 Pages

Spine Deformity Assessment for Scoliosis Diagnostics Utilizing Image Processing Techniques: A Systematic Review

  • Nurhusna Najeha Amran,
  • Khairul Salleh Basaruddin,
  • Muhammad Farzik Ijaz,
  • Haniza Yazid and ,
  • Shafriza Nisha Basah,
  • Nor Amalina Muhayudin and
  • Abdul Razak Sulaiman
  • + 2 authors+ 0 author

22 October 2023

Spinal deformity refers to a range of disorders that are defined by anomalous curvature of the spine and may be classified as scoliosis, hypo/hyperlordosis, or hypo/hyperkyphosis. Among these, scoliosis stands out as the most common type of spinal de...

(This article belongs to the Special Issue Advanced Imaging in Orthopedic Biomechanics)
  • Article
  • Open Access
9 Citations
3,080 Views
17 Pages

Deformation Behavior and Processing Maps of 7075 Aluminum Alloy under Large-Strain Thermal Compression

  • Erli Xia,
  • Tuo Ye,
  • Sawei Qiu,
  • Limei Liu and ,
  • Fang Luo,
  • Huanyu Yue and
  • Yuanzhi Wu
  • + 2 authors+ 0 author

29 November 2023

The investigation of thermal deformation behavior plays a significant role in guaranteeing the overall performance of alloy materials. In this manuscript, a series of isothermal compression tests at different temperatures (300, 350, 400, and 450 °...

(This article belongs to the Special Issue Research on the Microstructure and Properties of Metal Alloys)
  • Article
  • Open Access
18 Citations
3,089 Views
20 Pages

Spatiotemporal Deformation of Existing Pipeline Due to New Shield Tunnelling Parallel Beneath Considering Construction Process

  • Xiang Liu,
  • Annan Jiang,
  • Qian Fang,
  • Yousheng Wan and ,
  • Jianye Li and
  • Xinping Guo
  • + 1 author+ 0 author

5 January 2022

In this paper, we study the effects of the shield tunnel construction on the deformation of an existing pipeline parallel to and above the new shield tunnel. We propose an analytical solution to predict the spatiotemporal deformation of the existing...

(This article belongs to the Special Issue Deep Rock Mass Engineering: Excavation, Monitoring, and Control)
  • Article
  • Open Access
108 Views
22 Pages

High-Temperature Hot Deformation Behavior and Processing Map of TC11 Titanium Alloy

  • Yanchun Zhu,
  • Yefan Li,
  • Jie Lu,
  • Shijie Wang and ,
  • Lei Liu,
  • Zhibing Chu,
  • Shangwu Jia,
  • Yong Niu and
  • Fan Wang
  • + 4 authors+ 0 author

4 November 2026

In this study, the high-temperature deformation behavior of TC11 titanium alloy was investigated through hot compression experiments. The relationship between flow stress, strain rate, and deformation temperature was described by analyzing stress&nda...

(This article belongs to the Section Metal Casting, Forming and Heat Treatment)
  • Article
  • Open Access
6 Citations
2,418 Views
12 Pages

Deformation and Fracture Characterization of an Mg-Sn-Ca Alloy Using 3D Processing Maps

  • Chenchen Zhi,
  • Zhenyu Wu,
  • Junyi Lei,
  • Zhiquan Huang and ,
  • Haijie Xv,
  • Yanchun Zhu,
  • Weitao Jia,
  • Pengtao Liu and
  • Lifeng Ma
  • + 4 authors+ 0 author

24 March 2023

The deformation and fracture characterization of an Mg−2Sn−1Ca alloy were studied through uniaxial isothermal compression tests. The flow stress curves, the efficiency of power dissipation, the instability parameter and the fracture behav...

(This article belongs to the Section Metal Casting, Forming and Heat Treatment)
  • Article
  • Open Access
17 Citations
5,281 Views
22 Pages

Effect of SiC Nanoparticles on Hot Deformation Behavior and Processing Maps of Magnesium Alloy AZ91

  • Kaibo Nie,
  • Xinkai Kang,
  • Kunkun Deng,
  • Ting Wang and ,
  • Yachao Guo and
  • Hongxia Wang
  • + 1 author+ 0 author

1 February 2018

The hot deformation behavior and processing characteristics of AZ91 alloy and nano-SiCp/AZ91 composite were compared at temperature ranges of 523 K–673 K and strain rates of 0.001–1 s−1. Positive impact of SiC nanoparticles on pinning grain boundarie...

  • Article
  • Open Access
17 Citations
3,725 Views
13 Pages

Hot Deformation Behavior and Processing Maps of a New Ti-6Al-2Nb-2Zr-0.4B Titanium Alloy

  • Zhijun Yang,
  • Weixin Yu,
  • Shaoting Lang,
  • Junyi Wei and ,
  • Guanglong Wang and
  • Peng Ding
  • + 1 author+ 0 author

9 May 2021

The hot deformation behaviors of a new Ti-6Al-2Nb-2Zr-0.4B titanium alloy in the strain rate range 0.01–10.0 s−1 and temperature range 850–1060 °C were evaluated using hot compressing testing on a Gleeble-3800 simulator at 60% of deformation degree....

  • Article
  • Open Access
1 Citations
1,663 Views
16 Pages

Hot Deformation Behavior and Processing Maps of Vapor-Phase-Grown Carbon Nanofiber Reinforced 7075Al Composites

  • Mengying Zhu,
  • Zhefeng Xu,
  • Junhua Wu,
  • Satoshi Motozuka and ,
  • Caili Tian,
  • Jianglong Gu and
  • Jinku Yu
  • + 2 authors+ 0 author

1 November 2024

The present study prepared 7075Al composites reinforced with vapor-phase-grown carbon nanofibers (VGCNFs) using the spark plasma sintering (SPS) method. Constitutive equations of the composites were calculated, and thermal processing maps were constr...

(This article belongs to the Special Issue Numerical and Experimental Advances in Metal Processing)
  • Article
  • Open Access
19 Citations
3,761 Views
17 Pages

20 February 2021

Hot compression tests over the temperature range from 350 °C to 500 °C and strain rates range from 0.001 s−1 to 1 s−1 for homogenized Al–6.32Zn–2.10Mg alloy were carried out on a Gleeble-3800 thermal simulation machine to characterize its hot deforma...

  • Article
  • Open Access
923 Views
13 Pages

Investigation into Hot Deformation Behavior and Processing Maps of 14CrMoR High-Performance Vessel Steel

  • Ya Gao,
  • Yuzhuo Zhao,
  • Yuan Gao,
  • Zejin Chen and ,
  • Yangbing Li,
  • Weina Zhang and
  • Zhenyu Liu
  • + 2 authors+ 0 author

20 October 2025

14CrMoR steel, possessing excellent low-temperature impact toughness and corrosion resistance, is an important material for core equipment in the coal chemical industry. In this paper, 14CrMoR steel was subjected to single-pass compression tests at d...

(This article belongs to the Special Issue Research on Microstructure and Performance Mechanisms of Advanced Steels and Alloys)
  • Article
  • Open Access
2 Citations
2,338 Views
14 Pages

Deformation Behavior and Processing Map of AlCoCrFeNiTi0.5 High-Entropy Alloy at High Temperature

  • Xinbin Liu,
  • Tiansheng Li,
  • Yong Wang,
  • Xianghua Kong and
  • Chenyang Zhao

22 October 2023

AlCoCrFeNiTi0.5 high-entropy alloy (HEA) shows excellent properties in hardness and corrosion resistance. AlCoCrFeNiTi0.5 HEA was prepared using a non-consumable vacuum arc furnace. Hot-deformation behavior of AlCoCrFeNiTi0.5 HEA was explored under 1...

(This article belongs to the Section Corrosion, Wear and Erosion)
  • Article
  • Open Access
340 Views
21 Pages

Hot Deformation Behavior and Processing Maps of 6082-T6 Aluminum Alloy Based on Friction and Temperature Correction

  • Zhenhu Wang,
  • Lijun Dong,
  • Yajun Luo,
  • Erli Xia and ,
  • Sawei Qiu,
  • Junjiang Xun,
  • Xindong Liu and
  • Heman Wen
  • + 3 authors+ 0 author

25 August 2026

In the current manuscript, the hot deformation behavior and the thermal processing map of 6082-T6 rolled aluminum alloy sheet were studied. A series of compression tests were conducted using the Gleeble-3500 thermal simulation machine under the condi...

(This article belongs to the Section Surface Characterization, Deposition and Modification)
  • Article
  • Open Access
5 Citations
3,487 Views
23 Pages

Steel Sheet Deformation in Clinch-Riveting Joining Process

  • Waldemar Witkowski,
  • Jacek Mucha and
  • Łukasz Boda

21 March 2024

This paper presents the deformation of a joined sheet after the clinch riveting process. The DX51D steel sheet with zinc coating was used. The samples to be joined with clinch riveting technology had a thickness of 1 ± 0.05 mm and 1.5 ±...

(This article belongs to the Special Issue New Technology of Welding/Joining of Metallic Materials)

of 213