Skip to Content

94 Results Found

  • Article
  • Open Access
1,201 Views
16 Pages

Wettability Study of Soldered Joints in SiC Ceramics and Combined Ni-SiC Using SnSbTi-Based Solder and Electron Beam Heating

  • Tomas Melus,
  • Roman Kolenak,
  • Jaromir Drapala,
  • Peter Gogola and ,
  • Matej Pasak,
  • Daniel Drimal and
  • Mikulas Sloboda
  • + 2 authors+ 0 author

16 June 2025

The reactive soldering of silicon-carbide (SiC) ceramics to a Ni-SiC composite was investigated using an Sn-5Sb-3Ti active solder and electron-beam heating at 750 °C, 850 °C and 950 °C. Wettability: The average contact angle decreased fro...

(This article belongs to the Special Issue Functionalized Ceramics and Their Composites: Preparation, Properties and Applications)
  • Article
  • Open Access
8 Citations
3,207 Views
11 Pages

Investigation of the Interfacial Reactions between the CoCuFeNi High Entropy Alloy and Sn Solder

  • Tzu-Yang Chiang,
  • Yong-Chi Chang,
  • Chao-Hong Wang,
  • Andromeda Dwi Laksono and
  • Yee-Wen Yen

5 April 2023

The CoCuFeNi high entropy alloy (HEA) has excellent electrical, thermal, and mechanical properties. In electronic packaging technology, Sn is the major element of lead-free solders. In this study, we used the CoCuFeNi HEA as the substrate and Sn as t...

(This article belongs to the Special Issue Feature Papers in Welding & Joining)
  • Feature Paper
  • Article
  • Open Access
8 Citations
6,654 Views
17 Pages

Metallurgical Soldering of Duplex CrN Coating in Contact with Aluminum Alloy

  • Pal Terek,
  • Lazar Kovačević,
  • Aleksandar Miletić,
  • Branko Škorić and ,
  • Janez Kovač and
  • Aljaž Drnovšek
  • + 1 author+ 0 author

24 March 2020

Coatings deposited by physical vapor deposition (PVD) significantly reduce the wear of high pressure die casting tools; however, cast alloy soldering still has a strong negative effect on production efficiency. Although a lot of research has been alr...

(This article belongs to the Special Issue Surface Topography Effects on Functional Properties of PVD Coatings)
  • Communication
  • Open Access
3 Citations
860 Views
14 Pages

17 December 2025

This study systematically investigates the influence of Bi content on the electromigration (EM) lifetime of low-temperature Cu/Sn-xBi-1Ag (600 μm)/Cu interconnects, where x = 57, 47 and 40 wt.%. The intrinsically higher product of diffusivity and...

(This article belongs to the Special Issue Research Advances in Microelectronics Packaging and Devices: From Materials to Reliability)
  • Article
  • Open Access
3 Citations
3,622 Views
12 Pages

28 August 2019

A typical dissolution wetting system, Bi-Sn eutectic filler metal over a Bi substrate in a high-purity argon atmosphere was investigated first using real-time in situ hot stage microscopy for the extensive use of the sharp-interface model and the dif...

(This article belongs to the Special Issue Multiscale Modeling of Materials and Processes)
  • Article
  • Open Access
19 Citations
10,665 Views
10 Pages

22 April 2016

The intermetallic compounds formed during the diffusion soldering of a Bi2Te2.55Se0.45 thermoelectric material with a Cu electrode are investigated. For this bonding process, Bi2Te2.55Se0.45 was pre-coated with a 1 μm Sn thin film on the thermoelectr...

(This article belongs to the Special Issue Intermetallics 2016)
  • Article
  • Open Access
20 Citations
4,587 Views
11 Pages

26 November 2022

Pt-nanoparticle (NP)-alloyed Sn-58Bi solders were reacted with electroless nickel-immersion gold (ENIG) and electroless nickel-electroless palladium-immersion gold (ENEPIG) surface finishes. We investigated formation of intermetallic compounds (IMCs)...

(This article belongs to the Section Advanced Materials Characterization)
  • Article
  • Open Access
9 Citations
2,333 Views
15 Pages

4 May 2024

Sn-3Ag-0.5Cu (SAC305)- and Sn-9Zn-based alloys (Sn-Zn-X, X = Al, In) are lead-free solders used in the fabrication of solder joints with Cu metallization. Electroplating is a facile technology used to fabricate Cu metallization. However, the addition...

(This article belongs to the Section Electronic Materials)
  • Review
  • Open Access
21 Citations
18,208 Views
39 Pages

11 November 2009

In this paper we will demonstrate how a thermodynamic-kinetic method can be utilized to rationalize a wide range of interfacial phenomena between Sn-based lead-free solders and Ni metallizations. First, the effect of P on the interfacial reactions, a...

  • Article
  • Open Access
439 Views
12 Pages

Effect of Reflow Temperature on Interfacial IMC Growth in Pb-Free/Pb Mixed-Assembly Micro-Solder Joints

  • Yang Xiao,
  • Yifan Bai,
  • Xinyuan He,
  • Qiming Cui and ,
  • Lijuan Cheng,
  • Rui Yang,
  • Qi Zhang and
  • Yong Wang
  • + 3 authors+ 0 author

29 August 2026

This study examines interfacial intermetallic compound (IMC) growth in Pb-free/Pb mixed assemblies comprising 450 µm SAC305 solder balls and Cu pads printed with a 0.12 mm layer of Sn63Pb37 solder paste. Samples were reflowed at peak temperatur...

(This article belongs to the Special Issue Advanced Surface Engineering Processes in Micro/Nano-Manufacturing)
  • Feature Paper
  • Article
  • Open Access
9 Citations
3,511 Views
11 Pages

The melting behavior and microstructure of bulk Sn-xIn (x = 6, 12 and 24, wt.%) solders and the thermomigration, elemental distribution and intermetallic compound (IMC) growth in Cu/Sn-xIn/Cu micro solder joints during soldering and aging under tempe...

(This article belongs to the Section Semiconductor Devices)
  • Article
  • Open Access
7 Citations
4,299 Views
8 Pages

16 June 2022

The development of advanced electronic devices leads to highly miniaturized interconnect circuits (ICs), which significantly increases the electromigration (EM) phenomenon of solder and circuits due to higher current density. The electromigration of...

(This article belongs to the Special Issue Advanced Packaging for Microsystem Applications)
  • Article
  • Open Access
7 Citations
2,734 Views
15 Pages

Improvement of PbSn Solder Reliability with Ge Microalloying-Induced Optimization of Intermetallic Compounds Growth

  • Zhibo Qu,
  • Yilong Hao,
  • Changhao Chen,
  • Yong Wang and ,
  • Shimeng Xu,
  • Shuyuan Shi,
  • Pengrong Lin and
  • Xiaochen Xie
  • + 3 authors+ 0 author

2 February 2024

PbSn solders are used in semiconductor devices for aerospace or military purposes with high levels of reliability requirements. Microalloying has been widely adopted to improve the reliability for Pb-free solders, but its application in PbSn solders...

(This article belongs to the Special Issue Advanced Electronic Packaging Technology: From Hard to Soft)
  • Article
  • Open Access
6 Citations
2,884 Views
8 Pages

21 October 2022

The application of Sn-0.7Cu-based composite solder in electronic packaging is limited due to its high melting point, poor wettability and low mechanical properties. Herein, we propose a strategy of adding Bi and Cr to improve the solderability of Sn-...

(This article belongs to the Special Issue New Welding Materials and Green Joint Technology)
  • Article
  • Open Access
20 Citations
3,751 Views
10 Pages

The In-Situ Observation of Grain Rotation and Microstructure Evolution Induced by Electromigration in Sn-3.0Ag-0.5Cu Solder Joints

  • Xing Fu,
  • Min Liu,
  • KeXin Xu,
  • Si Chen and ,
  • YiJun Shi,
  • ZhiWei Fu,
  • Yun Huang,
  • HongTao Chen and
  • RuoHe Yao
  • + 4 authors+ 0 author

2 December 2020

The in-situ observation of Sn-3.0Ag-0.5Cu solder joints under electromigration was conducted to investigate the microstructure and grain orientation evolution. It was observed that there was a grain rotation phenomenon during current stressing by in-...

  • Article
  • Open Access
13 Citations
4,259 Views
10 Pages

Metallization on Sapphire and Low-Temperature Joining with Metal Substrates

  • Jiajun Fang,
  • Qiaoxin Zhang,
  • Zhou Luo,
  • Wei Huang and ,
  • Zhenyu Liu,
  • Zhiwen Chen,
  • Xueqiang Cao and
  • Li Liu
  • + 3 authors+ 0 author

26 February 2022

To meet the packaging requirements of sapphire in special electronic components, there is an urgent need for a joining process that can realize a good connection between sapphire and dissimilar metals at a low temperature. In this work, the surface o...

(This article belongs to the Special Issue Physical Metallurgy of Metals and Alloys)
  • Article
  • Open Access
26 Citations
4,001 Views
13 Pages

30 April 2021

The mechanical properties of solder alloys are a performance that cannot be ignored in the field of electronic packaging. In the present study, novel Sn-Zn solder alloys were designed by the cluster-plus-glue-atom (CPGA) model. The effect of copper (...

  • Article
  • Open Access
11 Citations
3,571 Views
13 Pages

23 January 2024

It is difficult to confirm the existence of intermetallic compounds (IMCs) between SnIn and Cu, as their atomic numbers are very close, making it challenging to differentiate them through experimental tests. In order to determine IMCs and understand...

  • Article
  • Open Access
5 Citations
2,499 Views
14 Pages

Effect of Isothermal Annealing on Sn Whisker Growth Behavior of Sn0.7Cu0.05Ni Solder Joint

  • Aimi Noorliyana Hashim,
  • Mohd Arif Anuar Mohd Salleh,
  • Muhammad Mahyiddin Ramli,
  • Mohd Mustafa Al Bakri Abdullah and ,
  • Andrei Victor Sandu,
  • Petrica Vizureanu and
  • Ioan Gabriel Sandu
  • + 2 authors+ 0 author

24 February 2023

This paper presents an assessment of the effect of isothermal annealing of Sn whisker growth behavior on the surface of Sn0.7Cu0.05Ni solder joints using the hot-dip soldering technique. Sn0.7Cu and Sn0.7Cu0.05Ni solder joints with a similar solder c...

(This article belongs to the Special Issue Obtaining and Characterization of New Materials, Volume III)
  • Article
  • Open Access
7 Citations
3,605 Views
17 Pages

Design and Performance Evaluation of Sn58Bi/SAC305 Layered Composite Solder for Low-Temperature Applications

  • Zhongxu Zhang,
  • Dan Zhang,
  • Chenyu Li,
  • Wenlong Yang and ,
  • Haitao Ma,
  • Haoran Ma and
  • Yunpeng Wang
  • + 2 authors+ 0 author

12 February 2025

This study proposes a Sn58Bi/SAC305 layered composite solder designed for low-temperature applications. By alternating high-melting SAC305 and low-melting Sn58Bi layers, the composite achieves a liquidus temperature of ~180 °C, comparable to trad...

  • Article
  • Open Access
22 Citations
4,950 Views
15 Pages

22 March 2021

The purpose of this work is to explore the impact of 0.5, 1.5, 2.5 and 3.5 wt.% Bi additions on the microstructure and mechanical performance of Sn-1Ag-0.5Cu solder alloy. Scanning electron microscope (SEM) and X-ray diffraction (XRD) were utilized t...

(This article belongs to the Special Issue New Trends in Crystals at Saudi Arabia)
  • Article
  • Open Access
18 Citations
4,469 Views
19 Pages

Performance of Sn-3.0Ag-0.5Cu Composite Solder with Kaolin Geopolymer Ceramic Reinforcement on Microstructure and Mechanical Properties under Isothermal Ageing

  • Nur Syahirah Mohamad Zaimi,
  • Mohd Arif Anuar Mohd Salleh,
  • Andrei Victor Sandu,
  • Mohd Mustafa Al Bakri Abdullah and ,
  • Norainiza Saud,
  • Shayfull Zamree Abd Rahim,
  • Petrica Vizureanu,
  • Rita Mohd Said and
  • Mohd Izrul Izwan Ramli
  • + 4 authors+ 0 author

7 February 2021

This paper elucidates the effect of isothermal ageing at temperature of 85 °C, 125 °C and 150 °C for 100, 500 and 1000 h on Sn-3.0Ag-0.5Cu (SAC305) lead-free solder with the addition of 1 wt% kaolin geopolymer ceramic (KGC) reinforcement particles. S...

(This article belongs to the Special Issue Obtaining and Characterization of New Materials)
  • Article
  • Open Access
8 Citations
2,950 Views
16 Pages

Effect of Graphene Nanosheets on the Microstructure and Mechanical Properties of Sn-20Bi Solder

  • Wenchao Yang,
  • Weiou Qin,
  • Jingwu Wu,
  • Junli Feng and
  • Yongzhong Zhan

13 February 2023

The application of Sn-Bi series solder is limited due to the brittleness of Bi phase. Sn-20Bi solder with less Bi element content has great research prospects, but it needs modification to make it a substitute for traditional Sn-Pb solder. In this ar...

  • Article
  • Open Access
14 Citations
4,900 Views
18 Pages

Study on Thermal Cycling Reliability of Epoxy-Enhanced SAC305 Solder Joint

  • Peng Zhang,
  • Songbai Xue,
  • Lu Liu,
  • Jianhao Wang and ,
  • Hiroaki Tatsumi and
  • Hiroshi Nishikawa
  • + 1 author+ 0 author

14 September 2024

In this work, epoxy was added into commercial Sn-3.0Ag-0.5Cu (SAC305) solder paste to enhance the thermal cycling reliability of the joint. The microstructure and fracture surface were observed using a scanning electron microscope/energy dispersive s...

(This article belongs to the Special Issue Mechanical Behaviour of Polymeric-Based Systems Used in Engineering Applications)
  • Article
  • Open Access
3 Citations
2,158 Views
14 Pages

Effects of Minor Zn Dopants in Sn-10Bi Solder on Interfacial Reaction and Shear Properties of Solder on Ni/Au Surface Finish

  • Sijin Li,
  • Junxian Zhu,
  • Huiling Zhou,
  • Mingqing Liao and ,
  • Fengjiang Wang and
  • Jian Chen
  • + 1 author+ 0 author

3 September 2024

Sn-10Bi low-bismuth-content solder alloy provides a potential alternative to the currently used Sn-Ag-Cu series due to its lower cost, excellent ductility, and strengthening resulting from the Bi solid solution and precipitation. This study primarily...

(This article belongs to the Special Issue The Design, Preparation, and Mechanical Properties of New Metallic Materials and Alloys)
  • Article
  • Open Access
2 Citations
3,931 Views
8 Pages

Erosion Resistance Properties of Iron–Carbon Composite Plating to Molten Lead-Free Solder

  • Jun Watanabe,
  • Kenji Hatsuzawa,
  • Shigeyuki Ogata,
  • Shinichi Yoshida and
  • Ikuo Shohji

5 July 2019

The use of Sn-3mass%Ag-0.5mass%Cu lead-free solder (SAC305) has become common. Since SAC305 has a higher content of tin than conventional tin–lead eutectic solder, erosion of the Fe plating layer used in the solder iron tip and the point solder...

(This article belongs to the Special Issue Selected Papers from the NMJ2018)
  • Article
  • Open Access
6 Citations
3,912 Views
11 Pages

Effect of Tin Grain Orientation on Electromigration-Induced Dissolution of Ni Metallization in SnAg Solder Joints

  • Po-Ning Hsu,
  • Dai-Lung Lee,
  • Dinh-Phuc Tran,
  • Kai-Cheng Shie and ,
  • Nien-Ti Tsou and
  • Chih Chen
  • + 1 author+ 0 author

13 October 2022

In this study, symmetrical solder joints (Cu/Ni/SnAg2.3/Ni/Cu) were fabricated. They were electromigration (EM)-stressed at high (8 × 104 A/cm2) or low (1.6 × 104 A/cm2) current densities. Failures in the solder joints with different grai...

(This article belongs to the Section Manufacturing Processes and Systems)
  • Article
  • Open Access
40 Citations
8,182 Views
17 Pages

28 September 2020

This study investigates the shear strength and aging characteristics of Sn-3.0Ag-0.5Cu (SAC 305)/Cu joints by the addition of ZrO2 nanoparticles (NPs) having two different particle size: 5–15 nm (ZrO2A) and 70–90 nm (ZrO2B). Nanocomposite...

(This article belongs to the Special Issue Emerging Interconnection Technology and Pb-Free Solder Materials for Advanced Microelectronic Packaging)
  • Article
  • Open Access
11 Citations
2,899 Views
17 Pages

26 March 2023

To solve the electromigration problem of micro−electronic connection solder joints, an ideal electromigration tester was designed, and the thickness of the intermetallic compounds (IMCs), average void diameter, grain orientation, failure, shear...

  • Review
  • Open Access
4 Citations
3,647 Views
17 Pages

30 March 2023

This paper is a review of recent applications of a laser photothermal mirage technique for sensing and measuring the thermal resistance of joint layers in modern electronic devices. A straightforward theoretical model of the interfacial thermal resis...

(This article belongs to the Section Physical Sensors)
  • Review
  • Open Access
25 Citations
5,440 Views
20 Pages

21 July 2022

Sn-rich solder joints in three-dimensional integrated circuits and their reliability issues, such as the electromigration (EM), thermomigration (TM), and thermomechanical fatigue (TMF), have drawn attention related to their use in electronic packagin...

(This article belongs to the Section Electronic Materials)
  • Article
  • Open Access
18 Citations
6,296 Views
8 Pages

Interface Growth and Void Formation in Sn/Cu and Sn0.7Cu/Cu Systems

  • Jieshi Chen,
  • Yongzhi Zhang,
  • Zhishui Yu,
  • Peilei Zhang and ,
  • Wanqin Zhao,
  • Jin Yang and
  • Di Wu
  • + 2 authors+ 0 author

19 December 2018

In this work, the effects of electroplated Cu (EP Cu) and Cu addition (0.7%) in Sn solder on the intermetallic compounds (IMCs) growth and void formation were clarified by comparison with solder joints comprising of high purity Cu (HP Cu) substrate a...

(This article belongs to the Special Issue Selected Papers from the NMJ2018)
  • Article
  • Open Access
20 Citations
3,247 Views
13 Pages

12 February 2020

Dynamic observation of the microstructure evolution of Sn2.5Ag0.7Cu0.1RE/Cu solder joints and the relationship between the interfacial intermetallic compound (IMC) and the mechanical properties of the solder joints were investigated during isothermal...

  • Article
  • Open Access
7 Citations
2,931 Views
14 Pages

Diffusion Barrier Performance of Ni-W Layer at Sn/Cu Interfacial Reaction

  • Jinye Yao,
  • Chenyu Li,
  • Min Shang,
  • Xiangxu Chen and ,
  • Yunpeng Wang,
  • Haoran Ma,
  • Haitao Ma and
  • Xiaoying Liu
  • + 3 authors+ 0 author

25 July 2024

As the integration of chips in 3D integrated circuits (ICs) increases and the size of micro-bumps reduces, issues with the reliability of service due to electromigration and thermomigration are becoming more prevalent. In the practical application of...

(This article belongs to the Special Issue Advanced Electronic Packaging Technology: From Hard to Soft)
  • Article
  • Open Access
11 Citations
3,946 Views
17 Pages

Effects of Multiple Reflow on the Formation of Primary Crystals in Sn-3.5Ag and Solder Joint Strength: Experimental and Finite Element Analysis

  • Siti Farahnabilah Muhd Amli,
  • Mohd Arif Anuar Mohd Salleh,
  • Mohd Sharizal Abdul Aziz,
  • Hideyuki Yasuda and ,
  • Kazuhiro Nogita,
  • Mohd Mustafa Al Bakri Abdullah,
  • Ovidiu Nemes,
  • Andrei Victor Sandu and
  • Petrica Vizureanu
  • + 4 authors+ 0 author

13 June 2023

The growth and formation of primary intermetallics formed in Sn-3.5Ag soldered on copper organic solderability preservative (Cu-OSP) and electroless nickel immersion gold (ENIG) surface finish after multiple reflows were systematically investigated....

(This article belongs to the Section Construction and Building Materials)
  • Article
  • Open Access
11 Citations
4,778 Views
10 Pages

20 January 2022

In order to present the multiple reflow process during electronic packaging, the influence of the different short-time reheating temperatures on the microstructure and shear strength of the Cu/Au80Sn20/Cu solder joints was studied and discussed. The...

(This article belongs to the Topic Processing, Analysis, Modelling and Mechanics of Materials and Structures)
  • Article
  • Open Access
8 Citations
2,312 Views
13 Pages

27 September 2024

The sintering process of Cu nanoparticle (Cu NP)/graphene nanoplatelet (GNP) composite solder paste was thoroughly investigated in this work through molecular dynamics simulations. The tensile properties of the sintered Cu NP/GNP composite solder pas...

(This article belongs to the Section Advanced Nanomaterials and Nanotechnology)
  • Article
  • Open Access
5 Citations
2,448 Views
15 Pages

17 October 2023

A microwave transmitter/receiver using the low-temperature co-fired ceramic substrate and ball grid array packaging demonstrates superior properties, including high integration, miniaturization, and high electromagnetic shielding. However, it holds l...

(This article belongs to the Special Issue Advanced Electronic Packaging Technology: From Hard to Soft)
  • Article
  • Open Access
24 Citations
7,109 Views
13 Pages

Low Temperature Sealing Process and Properties of Kovar Alloy to DM305 Electronic Glass

  • Zhenjiang Wang,
  • Zeng Gao,
  • Junlong Chu,
  • Dechao Qiu and
  • Jitai Niu

13 July 2020

The low temperature sealing of Kovar alloy to DM305 electronic glass was realized by using lead-free glass solder of the Bi2O3-ZnO-B2O3 system in atmospheric environment. The sealing process was optimized by pre-oxidation of Kovar alloy and low tempe...

(This article belongs to the Special Issue Technology of Welding and Joining)
  • Article
  • Open Access
4 Citations
2,735 Views
13 Pages

Applicability Evaluation of Nano-Al2O3 Modified Sn-Ag-Cu Solder in High-Density Electronic Packaging Subjected to Thermal Cycling

  • Jie Wu,
  • Guoqiang Huang,
  • Yiping Wu,
  • Xiwu Huang and ,
  • Rui Yu,
  • Xuqi Yang,
  • Guangyao Chen,
  • Cheelong Tan,
  • Zhihao Yu and
  • Yong Xu
  • + 6 authors+ 1 author

1 December 2022

Recently, 3D packaging has been regarded as an important technical means to continue Moore’s Law. However, excessive stacking will increase the longitudinal dimension, and one chip with high-density bondings packaging is still needed. Thus, it...

(This article belongs to the Special Issue Advances in Metal Matrix Composites)
  • Article
  • Open Access
19 Citations
5,928 Views
9 Pages

The Effect of Grain Orientation of β-Sn on Copper Pillar Solder Joints during Electromigration

  • Kexin Xu,
  • Xing Fu,
  • Xinjie Wang,
  • Zhiwei Fu and ,
  • Xiaofeng Yang,
  • Si Chen,
  • Yijun Shi,
  • Yun Huang and
  • Hongtao Chen
  • + 4 authors+ 0 author

24 December 2021

The grain orientation of Sn-based solder joints on copper pillars under the combined action of electron wind force and temperature gradient greatly affects their electromigration damage. The copper pillars with Sn-1.8Ag lead-free solder on the top wa...

(This article belongs to the Section Electronic Materials)
  • Article
  • Open Access
21 Citations
6,030 Views
12 Pages

25 October 2018

Solder joints in thermally uncontrolled microelectronic assemblies have to be exposed to extreme temperature environments during deep space exploration. In this study, extreme temperature thermal shock test from −196 °C to 150 °C was performed on qua...

(This article belongs to the Special Issue Selected Papers from the NMJ2018)
  • Article
  • Open Access
9 Citations
3,534 Views
10 Pages

Microstructure and Grain Orientation Evolution in SnPb/SnAgCu Interconnects Under Electrical Current Stressing at Cryogenic Temperature

  • Xing Fu,
  • Yunfei En,
  • Bin Zhou,
  • Si Chen and ,
  • Yun Huang,
  • Xiaoqi He,
  • Hongtao Chen and
  • Ruohe Yao
  • + 3 authors+ 0 author

15 May 2019

Electromigration was characterized at the cathode Cu/solder interface—without the effect of Joule heating—by employing scanning electron microscopy (SEM) and electron backscatter diffraction (EBSD) analyses. Rapid (Cux,Ni1−x)6Sn5 in...

  • Article
  • Open Access
431 Views
14 Pages

Aging Effect on IMC Evolution in Bi-Based and SAC Soldering Pastes on 3D-Shaped Aluminum Cores

  • Aneta Chołaj,
  • Marek Kościelski,
  • Izabela Spocińska,
  • Wojciech Szymański and ,
  • Sonia Boczkal,
  • Anna Sitek,
  • Dorota Liszewska and
  • Mirosław Kozłowski
  • + 3 authors+ 0 author

12 June 2026

The increasing power density of modern electronic systems intensifies challenges related to heat dissipation and long-term reliability. Insulated metal substrates (IMS), particularly three-dimensional (3D), are increasingly used as integrated thermal...

(This article belongs to the Special Issue Feature Papers Collection in the Section ‘Electrical, Electronics and Communications Engineering’, Second Edition)
  • Article
  • Open Access
20 Citations
8,097 Views
8 Pages

Effect of Surface Roughness and Electroless Ni–P Plating on the Bonding Strength of Bi–Te-based Thermoelectric Modules

  • Sung Hwa Bae,
  • Sungsoon Kim,
  • Seong Hoon Yi,
  • Injoon Son and ,
  • Kyung Tae Kim and
  • Hoyong Chung
  • + 1 author+ 0 author

26 March 2019

In this study, electroless-plating of a nickel-phosphor (Ni–P) thin film on surface-controlled thermoelectric elements was developed to significantly increase the bonding strength between Bi–Te materials and copper (Cu) electrodes in ther...

(This article belongs to the Special Issue Thin Films for Thermoelectric Applications)
  • Article
  • Open Access
32 Citations
6,271 Views
11 Pages

6 January 2018

In order to accelerate the growth of interfacial intermetallic compound (IMC) layers in a soldering structure, Cu/SAC305/Cu was first ultrasonically spot soldered and then subjected to isothermal aging. Relatively short vibration times, i.e., 400 ms...

  • Review
  • Open Access
5 Citations
1,865 Views
16 Pages

12 December 2025

Electromigration (EM) presents a major reliability challenge in advanced electronic packaging as device scaling and rising power demands lead to higher current densities in solder joints. While eutectic Sn-58Bi solder is widely adopted as a low-tempe...

  • Article
  • Open Access
14 Citations
5,828 Views
17 Pages

Investigation of the Microstructure, Thermal Properties, and Mechanical Properties of Sn-Bi-Ag and Sn-Bi-Ag-Si Low Temperature Lead-Free Solder Alloys

  • Sheng Chen,
  • Xinbao Wang,
  • Zhiqiu Guo,
  • Changjun Wu and ,
  • Yongxiong Liu,
  • Ya Liu and
  • Xuping Su
  • + 2 authors+ 0 author

27 January 2023

In this study, we investigated the microstructure, mechanical properties, and thermal performance of Sn-xBi-1Ag (x = 35, 37, 45, and 47 wt.%) solders, with a particular focus on the effect of adding trace Si atoms. The impact of different Ag concentr...

(This article belongs to the Topic Environmental Sensitivity and Safety Assessment of Materials)
  • Article
  • Open Access
3 Citations
2,319 Views
17 Pages

16 January 2025

In this study, we designed and manufactured an ideal electromigration testing device for soldering joints to solve the reliability problems caused by temperature and current density changes in the electromigration processes of micro solder joints. We...

  • Article
  • Open Access
15 Citations
5,472 Views
23 Pages

Electrodeposition of Tin-Reduced Graphene Oxide Composite from Deep Eutectic Solvents Based on Choline Chloride and Ethylene Glycol

  • Stefania Costovici,
  • Aida Pantazi,
  • Danut Balan,
  • Anca Cojocaru and ,
  • Teodor Visan,
  • Marius Enachescu and
  • Liana Anicai
  • + 2 authors+ 0 author

19 January 2023

Some experimental results regarding the direct electrodeposition of tin-reduced graphene oxide composite (Sn-rGO) compared to the electrodeposition of tin metal (Sn) from a deep eutectic solvent (DES), namely using choline chloride-ethylene glycol eu...

of 2