Skip to Content

91 Results Found

  • Article
  • Open Access
6 Citations
3,217 Views
14 Pages

31 March 2022

A 2A12 aluminum alloy component with uniform high-strength and ductility was developed via predeformation (one-pass repetitive upsetting extrusion) and annular channel angular extrusion (ACAE). Moreover, the microstructure evolution and age-hardening...

(This article belongs to the Special Issue Corrosion and Degradation of Materials)
  • Article
  • Open Access
20 Citations
4,953 Views
11 Pages

Aging Response and Precipitation Behavior after 5% Pre-Deformation of an Al-Mg-Si-Cu Alloy

  • Shuoxun Jin,
  • Tungwai Ngai,
  • Liejun Li,
  • Shian Jia and ,
  • Tongguang Zhai and
  • Dongjie Ke
  • + 1 author+ 0 author

13 August 2018

In this study, Al-1.00 Mg-0.65 Si-0.24 Cu alloy was solution heat-treated, water-quenched, and then pre-deformed for 5% before aging. The peak hardness and yield strength of the pre-deformed sample with subsequent artificial aging were similar to tha...

(This article belongs to the Section Advanced Materials Characterization)
  • Article
  • Open Access
3 Citations
2,291 Views
18 Pages

Effects of Pre-Deformation in Corrosion Fatigue Crack Growth of Al-Mg-Zn Alloy

  • Hui Jiang,
  • Junjun Jin,
  • Yu Fang,
  • Guoqing Gou and ,
  • Wei Lu,
  • Zhiyi Zhang,
  • Hongmei Zhou,
  • Hairong Sun,
  • Jikui Feng and
  • Zhenghong Fu
  • + 6 authors+ 1 author

15 January 2025

This study investigated the effect of pre-deformation on the corrosion fatigue crack propagation (CFCG) of Al-Mg-Zn alloy in a corrosive environment. Tensile tests at different pre-deformation levels and molecular dynamics simulations analyzed change...

(This article belongs to the Special Issue Alloy Strengthening Mechanisms, Microstructure Control, and Performance Optimization)
  • Article
  • Open Access
78 Views
20 Pages

13 November 2026

Welding deformation in crane booms presents intractable challenges in manufacturing. An innovative simulation approach, based on the inherent strain method and pre-deformation method (ISM-PDM), is proposed to control welding deformation effectively i...

(This article belongs to the Section Welding and Joining)
  • Article
  • Open Access
4 Citations
3,593 Views
15 Pages

Effect of Pre-Deformation on the Microstructure and Precipitation Behavior of Spray-Formed 7xxx Series Aluminum Alloys

  • Huiying Hou,
  • Lei Zhang,
  • Shuohao Xing,
  • Hongchao Zhai and ,
  • Shule Xia,
  • Long Zhai,
  • Zhijie Wang and
  • Sha Liu
  • + 3 authors+ 0 author

26 March 2025

This study investigates the effect of pre-deformation on the microstructure and precipitation behavior of spray-formed 7xxx series aluminum alloys. Pre-deformation introduces a high density of dislocations, increasing the proportion of low-angle grai...

(This article belongs to the Section Corrosion and Protection)
  • Article
  • Open Access
2 Citations
847 Views
15 Pages

Effect of Pre-Deformation on Microstructure and Mechanical Properties of a Mg-Rich High-Cu Al-Mg-Si-Cu Alloy

  • Lipeng Ding,
  • Yuqi Yang,
  • Yue Zheng,
  • Tengqiang Yin and ,
  • Huilan Huang and
  • Yaoyao Weng
  • + 1 author+ 0 author

26 March 2026

The influence of pre-deformation on the microstructure and mechanical properties of a Mg-rich high-Cu Al-Mg-Si-Cu alloy was systematically investigated by hardness measurement, tensile test, and atomic resolution high-angle annular dark-field scannin...

(This article belongs to the Special Issue Processing, Microstructure and Properties of Aluminium Alloys)
  • Article
  • Open Access
1 Citations
1,619 Views
14 Pages

The Effect of Pre-Deformation on the Microstructure and Hardness of Al-Zn-Mg-Cu Alloy

  • Hongchao Zhai,
  • Lei Zhang,
  • Shuohao Xing,
  • Huiying Hou and ,
  • Zhijie Wang and
  • Sha Liu
  • + 1 author+ 0 author

28 February 2025

In this paper, hot rolling pre-deformation treatment was applied to an Al-Zn-Mg-Cu alloy after solid solution treatment, followed by peak aging treatment. The effect of the degree of deformation was discussed. The microstructure of the alloy after tr...

(This article belongs to the Section Surface Characterization, Deposition and Modification)
  • Article
  • Open Access
413 Views
22 Pages

16 May 2026

This study experimentally investigates the subsequent yield surfaces of thin-walled tubular ductile cast iron (QT600-7) specimens under various pre-deformation histories and elucidates their evolution patterns. The effects of pre-deformation level, u...

(This article belongs to the Special Issue Achievements in Foundry Materials and Technologies (Second Edition))
  • Article
  • Open Access
1 Citations
2,368 Views
12 Pages

Effects of Pre-Deformation under Tension and Annealing Process on the Microstructure and Properties of Al-6Mg-1.0Mn Extruded Wide Reinforcement Plate

  • Pengwei Li,
  • Qiqiang Han,
  • Wei Sun,
  • Xiangjie Wang and ,
  • Jianzhong Cui,
  • Rui Wang,
  • Chunzhong Liu and
  • Min Jiang
  • + 3 authors+ 0 author

6 October 2022

In order to achieve the combination of mechanical and corrosion properties for the Al-Mg-Mn alloy, a novel combination of pre-deformation under tension and an annealing process was investigated on the microstructure and properties of the Al-6Mg-1.0Mn...

(This article belongs to the Special Issue Progress in Light Alloys)
  • Article
  • Open Access
2 Citations
2,280 Views
20 Pages

17 May 2022

This paper presents research on the influence of material anisotropy caused by the technological process of its manufacturing on the plastic properties of the material. In the experimental study, samples cut from an AISI 304L rolled sheet in the roll...

  • Article
  • Open Access
8 Citations
2,165 Views
11 Pages

Accelerating Discontinuous Precipitation to Increase Strength by Pre-Deformation in Cu-Ni-Si Alloys

  • Yicheng Cao,
  • Wei Luo,
  • Wenjing Zhang,
  • Haofeng Xie and ,
  • Zhen Yang,
  • Zengde Li,
  • Lijun Peng and
  • Yunqing Zhu
  • + 3 authors+ 0 author

20 November 2024

Discontinuous precipitation-strengthened Cu-Ni-Si alloys are highly regarded for their combination of high strength and excellent electrical conductivity. However, the slow process of discontinuous precipitation, typically requiring up to 24 h for co...

(This article belongs to the Special Issue Microstructure, Mechanical Properties, and Deformation Characteristics of Metals and Alloys)
  • Article
  • Open Access
166 Views
19 Pages

Strain-Dependent High-Temperature Low-Cycle Fatigue Behavior and Damage Mechanisms of GH4169 Alloy After Cold-Drawing Pre-Deformation and Short-Time Annealing

  • Haiquan Liu,
  • Xinyu Gu,
  • Senhao Yang,
  • Ting Xiong and ,
  • Yanzhong Tian,
  • Meng Wang and
  • Feng Liu
  • + 2 authors+ 0 author

31 October 2026

The high-temperature low-cycle fatigue (LCF) response of GH4169 (Inconel 718) is sensitive to the initial microstructural state, yet the coupled effects of cold-drawing pre-deformation and subsequent annealing remain insufficiently understood. A dire...

(This article belongs to the Special Issue Advanced Metallic Materials for Structural and Functional Applications: Processing, Microstructure and Performance)
  • Article
  • Open Access
6 Citations
2,227 Views
16 Pages

2 March 2023

In this paper, the effects of compressive pre-deformation and successive pre-artificial aging on the compressive creep aging behavior and microstructure evolution of the Al-Cu-Li alloy have been studied. Severe hot deformation mainly occurs near the...

(This article belongs to the Section Metals and Alloys)
  • Article
  • Open Access
15 Citations
4,319 Views
12 Pages

26 October 2018

Columnar-grained Cu71.7Al18.1Mn10.2 shape memory alloy (SMA) was prepared by a directional solidification method and exhibited a high superelasticity of 8.18% and excellent ductility at room temperature, which provided the possibility of obtaining hi...

  • Article
  • Open Access
1 Citations
1,678 Views
13 Pages

8 August 2024

Ti-13Nb-13Zr-7Ag (TNZ-7Ag) has a great potential for biomedical application due to its low elastic modulus and excellent antibacterial properties. However, it is difficult to balance low elastic modulus and high antibacterial properties. In this stud...

(This article belongs to the Special Issue Design, Phase Transformation and Mechanical Properties of Titanium Alloy)
  • Article
  • Open Access
3 Citations
3,346 Views
18 Pages

Amplitude Dependent Internal Friction in Strained Magnesium Alloys of AZ Series

  • Milan Uhríčik,
  • Zuzana Dresslerová,
  • Peter Palček,
  • Mária Chalupová and ,
  • Zuzanka Trojanová and
  • Patrícia Hanusová
  • + 1 author+ 0 author

13 July 2020

Amplitude dependent internal friction (ADIF) was measured in three AZ magnesium alloys. Two types of experiments were performed: ADIF was measured step by step with the increasing strain amplitude and ADIF was measured after predeformation of samples...

(This article belongs to the Special Issue Study Properties of Hexagonal Single Crystals and Polycrystals)
  • Article
  • Open Access
9 Citations
3,565 Views
15 Pages

21 March 2020

Surface hardening treatment can usually introduce severe grain distortion with a large gradient in the surface layer. It results in mechanical properties being difficult to accurately determine through macroscopic tests due to the non-uniformity of t...

  • Article
  • Open Access
2 Citations
1,224 Views
24 Pages

Influence of Ply Angle on the Cavitation Performance of Composite Propellers

  • Zheng Huang,
  • Zhangtao Chen,
  • Shenhan Lin and
  • Sinan Wu

In response to the core challenge of effectively controlling deformation to suppress cavitation in composite propellers under fluid–structure interaction (FSI), this study proposes a numerical investigation method based on pre-deformation desig...

(This article belongs to the Special Issue Advanced Studies in Ship Fluid Mechanics)
  • Article
  • Open Access
12 Citations
4,093 Views
9 Pages

Effect of Pre-Strain on Microstructure and Tensile Properties of Ti-6Al-4V at Elevated Temperature

  • Taowen Wu,
  • Ning Wang,
  • Minghe Chen,
  • Dunwen Zuo and ,
  • Lansheng Xie and
  • Wenxiang Shi
  • + 1 author+ 0 author

20 August 2021

Research on pre-deformation influences on material properties in multistep hot forming is of important scientific interest. In this paper, hot tensile tests at 850 °C and a strain rate of 0.001 s−1 were performed to study the microstructural evolutio...

(This article belongs to the Special Issue Titanium Alloys and Titanium-Based Matrix Composites)
  • Article
  • Open Access
9 Citations
2,242 Views
18 Pages

11 October 2023

Rolling contact fatigue loading causes the surface material in the top of the rail to severely deform. The microstructure aligns along the shear direction and the mechanical behavior in terms of plastic flow becomes anisotropic. Cracks are initiated...

(This article belongs to the Section Metal Failure Analysis)
  • Article
  • Open Access
7 Citations
3,659 Views
12 Pages

Modulation of Multiple Precipitates for High Strength and Ductility in Al-Cu-Mn Alloy

  • Linxiang Liu,
  • Zhijun Wang,
  • Qingfeng Wu,
  • Zhongsheng Yang and ,
  • Kexuan Zhou,
  • Xiaoguang Fan,
  • Junjie Li and
  • Jincheng Wang
  • + 3 authors+ 0 author

2 December 2021

The category and morphology of precipitates are essential factors in determining the mechanical behaviors of aluminum alloys. It is a great challenge to synthetically modulate multiple precipitates to simultaneously improve strength and ductility. In...

(This article belongs to the Special Issue Feature Papers in "Metals and Alloys" Section)
  • Article
  • Open Access
17 Citations
5,188 Views
18 Pages

The Effect of Dynamic Recrystallization on Monotonic and Cyclic Behaviour of Al-Cu-Mg Alloy

  • Adam Tomczyk,
  • Andrzej Seweryn and
  • Małgorzata Grądzka-Dahlke

23 May 2018

The paper presents an investigation that was conducted to determine the possibility of the occurrence of the process of dynamic recrystallization in 2024 alloy during monotonic tensile and creep tests at the elevated temperatures of 100 °C, 200 &...

(This article belongs to the Special Issue Dynamic Recrystallization and Microstructural Evolution in Alloys)
  • Article
  • Open Access
8 Citations
3,091 Views
17 Pages

The Effect of Predeformation on Creep Strength of 9% Cr Steel

  • Petr Král,
  • Jiří Dvořák,
  • Wolfgang Blum,
  • Václav Sklenička and ,
  • Zenji Horita,
  • Yoichi Takizawa,
  • Yongpeng Tang,
  • Lenka Kunčická,
  • Radim Kocich and
  • Marie Svobodová
  • + 6 authors+ 1 author

25 November 2020

Martensitic creep-resistant P92 steel was deformed by different methods of severe plastic deformation such as rotation swaging, high-pressure sliding, and high-pressure torsion at room temperature. These methods imposed significantly different equiva...

(This article belongs to the Special Issue Creep and High Temperature Deformation of Steels and Alloys)
  • Article
  • Open Access
4 Citations
3,164 Views
14 Pages

14 May 2020

To solve the problem of the slow convergence of the geometry-based correction (GC) method in the design of a steam turbine blade, this paper proposes a geometry-load-based hybrid correction (GLHC) method. In this method, the deformation of the blade...

(This article belongs to the Section F: Electrical Engineering)
  • Article
  • Open Access
683 Views
29 Pages

Study on the Synergistic Effects of Pre-Deformation and Post-Aging Treatments on the Mechanical and Corrosion Properties of a 2A97 Al-Cu-Li Alloy

  • Danyang Liu,
  • Bangguo Wu,
  • Xin Liu,
  • Li Wang and ,
  • Hua Zhou,
  • Lei Tang,
  • Kefu Gan and
  • Jinfeng Li
  • + 3 authors+ 0 author

This work systematically investigates the effects of pre-deformation, post-aging temperature, and aging time on the mechanical properties, corrosion behavior, and microstructure of a 2A97 Al-Cu-Li alloy. Microstructural characterization indicates tha...

(This article belongs to the Topic Advances in Processing, Microstructure and Mechanical Properties of Lightweight Alloys)
  • Article
  • Open Access
22 Citations
4,121 Views
11 Pages

12 May 2019

Deformation of an as-rolled rare earth Mg-2Y-0.6Nd-0.6Zr alloy, at different temperatures, was carried out along the BC (90° anticlockwise rotation of the samples after each ECAP pass) route by equal channel angular pressing (ECAP). The effects o...

  • Article
  • Open Access
1 Citations
1,000 Views
20 Pages

16 February 2026

This study investigated high-speed air-atomized water-mist impingement cooling of 2219 aluminum alloy plates using a self-developed spray-quenching setup. Cooling intensity was controlled by varying the water loading fraction, and cooling curves were...

(This article belongs to the Section Metal Casting, Forming and Heat Treatment)
  • Article
  • Open Access
11 Citations
3,629 Views
20 Pages

Effects of Austenitization Temperature and Pre-Deformation on CCT Diagrams of 23MnNiCrMo5-3 Steel

  • Ivo Schindler,
  • Rostislav Kawulok,
  • Petr Opěla,
  • Petr Kawulok and ,
  • Stanislav Rusz,
  • Jaroslav Sojka,
  • Michal Sauer,
  • Horymír Navrátil and
  • Lukáš Pindor
  • + 4 authors+ 0 author

13 November 2020

The combined effect of deformation temperature and strain value on the continuous cooling transformation (CCT) diagram of low-alloy steel with 0.23% C, 1.17% Mn, 0.79% Ni, 0.44% Cr, and 0.22% Mo was studied. The deformation temperature (identical to...

(This article belongs to the Special Issue Hot Deformation and Microstructure Evolution of Metallic Materials)
  • Article
  • Open Access
7 Citations
2,570 Views
25 Pages

21 September 2024

AISI 316L austenitic stainless steel is utilized in various processing industries, due to its abrasion resistance, corrosion resistance, and excellent properties over a wide temperature range. The physical and mechanical properties of a material chan...

(This article belongs to the Section Metal Failure Analysis)
  • Article
  • Open Access
14 Citations
3,415 Views
18 Pages

1 July 2022

Deformation and heat treatment are important means to strengthen aluminum alloys. However, the influence mechanism of pre-strain on aging precipitation kinetics and its effect on mechanical properties are still not clear. In this work, uniaxial isoth...

(This article belongs to the Special Issue Research on Heat Treatment of Advanced Metallic Materials)
  • Article
  • Open Access
11 Citations
2,839 Views
18 Pages

Study on the Aging Precipitation Behavior and Kinetics of Al-10.0Zn-3.0Mg-2.8Cu Alloy by Pre-Deformation Treatment

  • Zhaolong Fu,
  • Xi Zhao,
  • Minhang Jiao,
  • Xianwei Ren and ,
  • Hongbin Liu and
  • Hailong Liu
  • + 1 author+ 0 author

27 July 2024

In this paper, the effect of thermomechanical treatment process on the hardening behavior, grain microstructure, precipitated phase, and tensile mechanical properties of the new high-strength and high-ductility Al-10.0Zn-3.0Mg-2.8Cu alloy was studied...

(This article belongs to the Section Metals and Alloys)
  • Feature Paper
  • Article
  • Open Access
5 Citations
2,547 Views
12 Pages

Influence of a Pronounced Pre-Deformation on the Attachment of Melt Droplets and the Fatigue Behavior of Laser-Cut AISI 304

  • André T. Zeuner,
  • Thomas Wanski,
  • Sebastian Schettler,
  • Jonas Fell and ,
  • Andreas Wetzig,
  • Robert Kühne,
  • Sarah C. L. Fischer and
  • Martina Zimmermann
  • + 3 authors+ 0 author

19 January 2023

Laser cutting is a suitable manufacturing method for generating complex geometries for sheet metal components. However, their cyclic load capacity is reduced compared to, for example, milled components. This is due to the influence of the laser-cut e...

(This article belongs to the Special Issue Mechanical Behavior of Metallic Materials under Different Loading Conditions)
  • Article
  • Open Access
4 Citations
3,100 Views
16 Pages

An Investigation of the High-Speed Machinability of 7050 Aluminum Alloy Based on Different Prefabricated Crystal Orientations

  • Chenbing Ni,
  • Wei Lu,
  • Youqiang Wang,
  • Chengguo Zong and ,
  • Dejian Liu and
  • Guoliang Liu
  • + 1 author+ 0 author

21 September 2023

This study investigated the high-speed cutting performance of 7050 aluminum alloy with prefabricated crystal orientations under dry-cutting conditions. Three specimens with different crystal orientations were prefabricated using pre-deformations of 1...

(This article belongs to the Special Issue Friction and Wear of Alloys)
  • Article
  • Open Access
12 Citations
4,040 Views
10 Pages

Ageing Behaviour of Al–Mg–Si Alloys After Cryogenic and Room Temperature Deformation

  • Belinda Gruber,
  • Florian Grabner,
  • Werner Fragner,
  • Alexander Schökel and ,
  • Florian Spieckermann,
  • Peter J. Uggowitzer and
  • Stefan Pogatscher
  • + 2 authors+ 0 author

23 January 2020

The aim of this study is to investigate the effects of cryogenic and room temperature pre-deformation on subsequent artificial ageing of Al–Mg–Si alloys. Naturally aged and pre-aged samples were strained to 5%, 10% and 20% at RT (25 °...

(This article belongs to the Collection Alloy and Process Development of Light Metals)
  • Article
  • Open Access
17 Citations
3,399 Views
12 Pages

Microstructure and High Temperature Tensile Properties of Mg–10Gd–5Y–0.5Zr Alloy after Thermo-Mechanical Processing

  • Guohua Wu,
  • H. R. Jafari Nodooshan,
  • Xiaoqin Zeng,
  • Wencai Liu and ,
  • Dejiang Li and
  • Wenjiang Ding
  • + 1 author+ 0 author

23 November 2018

The microstructure, high-temperature tensile properties and fracture behavior of the Mg-10Gd-5Y-0.5Zr alloy after thermo-mechanical processing (pre-tension between solution and aging treatment) were investigated. The pre-deformed alloy shows the acce...

  • Article
  • Open Access
3 Citations
2,278 Views
19 Pages

Near Net Shape Manufacturing of Sheets from Al-Cu-Li-Mg-Sc-Zr Alloy

  • Barbora Kihoulou,
  • Rostislav Králík,
  • Lucia Bajtošová,
  • Olexandr Grydin and ,
  • Mykhailo Stolbchenko,
  • Mirko Schaper and
  • Miroslav Cieslar
  • + 2 authors+ 0 author

28 January 2024

Thin twin-roll cast strips from a model Al-Cu-Mg-Li-Zr alloy with a small addition of Sc were prepared. A combination of a fast solidification rate and a favorable effect of Sc microalloying refines the grain size and the size of primary phase partic...

(This article belongs to the Special Issue The 15th Anniversary of Materials—Recent Advances in Materials Physics)
  • Article
  • Open Access
5 Citations
3,108 Views
19 Pages

12 June 2020

Forming processes influence the mechanical properties of manufactured workpieces in general and by means of forming-induced initial damage in particular. The effect of the latter on performance capability is the underlying research aspect for the inv...

(This article belongs to the Special Issue Manufacturing and Fatigue Properties of Materials)
  • Article
  • Open Access
2 Citations
2,187 Views
25 Pages

To enhance the seismic performance of reinforced concrete (RC) elements, it is essential to consider both strength and ductility post-yielding. This study proposed a novel method to improve the ductility of RC piers by using preformed inward-bending...

(This article belongs to the Section Infrastructures and Structural Engineering)
  • Review
  • Open Access
1 Citations
1,148 Views
42 Pages

16 August 2026

Metal additive manufacturing (MAM) enables the fabrication of geometrically complex and high-performance components but is accompanied by steep thermal gradients, repeated thermal cycling, phase transformation, residual stress, and deformation. These...

(This article belongs to the Topic Microstructure and Properties in Metals and Alloys, 4th Edition)
  • Article
  • Open Access
3 Citations
1,837 Views
21 Pages

17 October 2024

The purpose of this investigation was to determine the extent to which a combination of pre-deformation and aging procedures could enhance the corrosion and wear resistance of the Ti-15Mo alloy for biomedical materials. The initial grains were refine...

(This article belongs to the Special Issue Advances in Surface Engineering and Biocompatible Coatings for Biomedical Applications, 2nd Edition)
  • Article
  • Open Access
12 Citations
3,366 Views
16 Pages

Effect of Deformation on Precipitation and the Microstructure Evolution during Multistep Thermomechanical Processing of Al-Zn-Mg-Cu Alloy

  • Jinrong Zuo,
  • Longgang Hou,
  • Xuedao Shu,
  • Wenfei Peng and ,
  • Anmin Yin and
  • Jishan Zhang
  • + 1 author+ 0 author

23 October 2020

In order to obtain fine grained structure efficiently, a new multi-step rolling process (MSR: pre-deformation + intermediate annealing + hot deformation) was applied in Al-Zn-Mg-Cu plates. Conventional hot rolling (CHR) was also carried out as a cont...

(This article belongs to the Section Metal Casting, Forming and Heat Treatment)
  • Article
  • Open Access
2 Citations
1,405 Views
20 Pages

Influence of Pre-Strain and Notching on the Fatigue Life of DD11 Low-Carbon Steel

  • Ivan Tomasi,
  • Luigi Solazzi,
  • Candida Petrogalli,
  • Alberto Mazzoni and
  • Giorgio Donzella

9 September 2025

Structural applications commonly adopt low-carbon steels, with the fatigue concept being one of the primary causes of failure. In this research, the aim was to study the fatigue behaviour of DD11 low-carbon steel, considering also specific conditions...

(This article belongs to the Special Issue Fatigue Damage Behavior and Mechanisms: Latest Advances and Prospects)
  • Article
  • Open Access
15 Citations
2,724 Views
20 Pages

Investigation on Mechanism of Microstructure Evolution during Multi-Process Hot Forming of GH4169 Superalloy Forging

  • Ming-Song Chen,
  • Hong-Wei Cai,
  • Yong-Cheng Lin,
  • Guan-Qiang Wang and ,
  • Hong-Bin Li,
  • An Liu,
  • Ze-Hao Li and
  • Shan Peng
  • + 3 authors+ 0 author

7 April 2024

Typically, in the manufacturing of GH4169 superalloy forgings, the multi-process hot forming that consists of pre-deformation, heat treatment and final deformation is required. This study focuses on the microstructural evolution throughout hot workin...

(This article belongs to the Special Issue Review and Feature Papers in "Metals and Alloys" Section)
  • Article
  • Open Access
18 Citations
2,687 Views
18 Pages

The Effect of Heat Input, Annealing, and Deformation Treatment on Structure and Mechanical Properties of Electron Beam Additive Manufactured (EBAM) Silicon Bronze

  • Andrey Filippov,
  • Nikolay Shamarin,
  • Evgeny Moskvichev,
  • Nikolai Savchenko and ,
  • Evgeny Kolubaev,
  • Ekaterina Khoroshko and
  • Sergei Tarasov
  • + 2 authors+ 0 author

29 April 2022

Electron beam additive wire-feed manufacturing of Cu-3wt.%S-0.8wt.%Mn bronze thin wall on a stainless steel substrate has been carried out at heat input levels of 0.19, 0.25, and 0.31 kJ/mm. The microstructures of as-deposited metal ranged from low a...

(This article belongs to the Special Issue Challenges in Additive Manufacturing of Metals and Their Alloys: Microstructure and Mechanical Properties)
  • Article
  • Open Access
7 Citations
2,623 Views
18 Pages

Hydrogen Diffusion in Deformed Austenitic TRIP Steel—A Study of Mathematical Prediction and Experimental Validation

  • Christian Hempel,
  • Marcel Mandel,
  • Caroline Quitzke,
  • Marco Wendler and ,
  • Thilo Kreschel,
  • Olena Volkova and
  • Lutz Krüger
  • + 2 authors+ 0 author

13 December 2024

This study focuses on the effect of pre-deformation on hydrogen diffusion and hydrogen embrittlement of the high alloy austenitic TRIP steel X3CrMnNiMo17-8-4. Different cold-rolled steel sheets with thicknesses of ≤400 µm were electrochemica...

(This article belongs to the Special Issue Corrosion Behavior and Mechanical Properties of Metallic Materials)
  • Article
  • Open Access
4 Citations
2,679 Views
11 Pages

Enhanced Magnetostrain in a <0 0 1>A-Textured Ni44.5Co4.9Mn37.5In13.1 Alloy through Superelastic Training

  • Lanyu Guo,
  • Zongbin Li,
  • Jiaxing Chen,
  • Bo Yang and ,
  • Haile Yan,
  • Xiang Zhao,
  • Claude Esling and
  • Liang Zuo
  • + 3 authors+ 0 author

11 March 2022

Large magnetostrain can be demonstrated in Ni-Mn-X (X = In, Sn, Sb) meta-magnetic shape memory alloys by resuming the predeformed martensite through magnetic-field-induced reverse martensitic transformation. However, owing to the constraint from the...

(This article belongs to the Special Issue Phase Transformation, Functional Properties, and Crystallography of Advanced Materials)
  • Review
  • Open Access
69 Citations
9,571 Views
35 Pages

A Brief Review of the Shape Memory Phenomena in Polymers and Their Typical Sensor Applications

  • Li Sun,
  • Tao Xi Wang,
  • Hong Mei Chen,
  • Abhijit Vijay Salvekar and ,
  • Balasundaram Selvan Naveen,
  • Qinwei Xu,
  • Yiwei Weng,
  • Xinli Guo,
  • Yahui Chen and
  • Wei Min Huang
  • + 5 authors+ 0 author

15 June 2019

In this brief review, an introduction of the underlying mechanisms for the shape memory effect (SME) and various shape memory phenomena in polymers is presented first. After that, a summary of typical applications in sensors based on either heating o...

(This article belongs to the Special Issue Shape Memory Polymers III)
  • Article
  • Open Access
5 Citations
4,217 Views
17 Pages

Recent technological advances have made it possible to manufacture steels with both high strength and high ductility. This is the case for Twinning-Induced Plasticity (TWIP) steels which are characterized by a twinning deformation mechanism, which is...

  • Article
  • Open Access
3 Citations
1,417 Views
18 Pages

Influence of Pre-Strain on the Course of Energy Dissipation and Durability in Low-Cycle Fatigue

  • Stanisław Mroziński,
  • Michał Piotrowski,
  • Władysław Egner and
  • Halina Egner

18 February 2025

The work undertaken in this paper is the comparative analysis of the accumulation of plastic strain energy in the as-received and pre-deformed (overloaded) material states, performed on the example of S420M steel. For this reason, the low-cycle fatig...

(This article belongs to the Special Issue High-Performance Applications of Advanced Materials: Material Properties, Behaviour Modeling, Optimal Design and Advanced Processes)
  • Article
  • Open Access
21 Citations
3,627 Views
16 Pages

Grain Refinement Assisted by Deformation Enhanced Precipitates through Thermomechanical Treatment of AA7055 Al Alloy

  • Jinrong Zuo,
  • Longgang Hou,
  • Xuedao Shu,
  • Wenfei Peng and ,
  • Anmin Yin and
  • Jishan Zhang
  • + 1 author+ 0 author

2 May 2020

Fine-grained sheets of AA7055 Al alloy were produced by an improved double-stage rolling thermomechanical treatment (DRTMT) assisted by deformation-enhanced precipitates (DEPs). The DRTMT composed of a low temperature pre-deformation, an intermediate...

of 2