Biofuels are environmental friendly renewable fuels, that can be directly used in a diesel engine. However, a few shortcomings like a higher density, viscosity, a lower calorific value and increase in NOx emissions, has caused researchers to look for...
Carbon–metal composite NiCrFeC coatings, prepared with and without controlled oxygen addition, were investigated to evaluate the influence of oxygen on the structure, mechanical response, and tribological performance. X-ray diffraction revealed...
A study on the application of oxygenated turpentine oil as a bio-additive in diesel fuel was conducted. The purpose of this research was to investigate the effect of oxygenated turpentine oil additive in diesel fuel on the performance and emission ch...
The aim of the study was to assess the influence of the addition of an oxygenated additive (a mixture of mono-, di- and triacetylglycerol obtained from residual glycerin within the biodiesel production scheme) on the specific fuel consumption and exh...
Ti-6Al-4V thin-walled specimens were fabricated by gas tungsten arc welding-based wire arc additive manufacturing under controlled oxygen concentrations of 1, 500 and 1000 ppm, with ambient air used as a severe oxygen-exposure reference. The effects...
This work aims to assess the effect of an oxygen content graded in minimal quantities, on the order of hundreds of ppms, on the determination of surface tension of low-alloy FeCOCr and FeCONi steels in contact with a corundum substrate. Oxygen, as a...
Biodiesel production has considerably increased in recent decades, generating a surplus of crude glycerol, which is the main drawback for the economy of the process. To overcome this, many scientists have directed their efforts to transform glycerol,...
NiCr composite coatings on stainless steel were obtained by the simultaneous deposition of Cr and Ni, using thermionic vacuum arc (TVA) technology. The main aim of this paper is to study the influence of graphite and oxygen incorporation on the struc...
This study examines the impact of the addition of bio-ethanol/bio-ETBE on the main volatility properties of gasoline. Although several studies have been published on the addition of ethanol or ETBE to gasoline, the simultaneous addition of these oxyg...
High-temperature face-centered cubic bismuth oxide phase is a material of great interest given its unique properties. In the present study, α-Bi2O3 and tantalum powders were used as the starting powders for the formation of high-temperature bismuth o...
Atomic layer deposition (ALD) technology has unlocked new ways of manipulating the growth of inorganic materials. The fine control at the atomic level allowed by ALD technology creates the perfect conditions for the inclusion of new cationic or anion...
In this study, micro-oxygen was integrated into a rusty scrap iron (RSI)-loaded anaerobic digester. Under an optimal RSI dosage of 20 g/L, increasing O2 levels were added stepwise in seven stages in a semi-continuous experiment. Results showed the av...
This study investigated the ecological selection and enrichment of anaerobic ammonium-oxidizing bacteria (AnAOB) driven by endogenous carbon cycling in a low-oxygen SBR biofilm system without external carbon addition. The system was operated using dr...
The C4F7N/CO2 mixture is considered one of the most promising alternatives to sulfur SF6. Recent studies have shown that the addition of O2 to the C4F7N/CO2 mixture can suppress carbon precipitation following electric arc discharges. This paper condu...
Combustion and heat release characteristics of biogas non-premixed flames under various hydrogen-enriched and oxygen-enriched conditions were investigated through chemical kinetics simulation using detailed chemical mechanisms. The heat release rates...
Heavy oil was divided into different pseudo-components according to their boiling ranges through a real-boiling point distillation process, and the oxidation products for pseudo-components with a boiling range higher than 350 °C were systematical...
Aromatic aldehydes that bind to sickle hemoglobin (HbS) to increase the protein oxygen affinity and/or directly inhibit HbS polymer formation to prevent the pathological hypoxia-induced HbS polymerization and the subsequent erythrocyte sickling have...
The blood oxygen saturation, which indicates the ratio of oxygenated hemoglobin to total hemoglobin in the blood, is closely related to one’s health status. Oxygen saturation is typically measured using a pulse oximeter. However, this method ca...
Selective Laser Melting (SLM) is an emerging Additive Manufacturing (AM) technique for the on-demand fabrication of metal parts. The mechanical properties of Selectively Laser Melted (SLMed) parts are sensitive to oxygen concentration within the SLM...
Flame-retardant polymeric coatings with high limiting oxygen index (LOI) were prepared by combining inorganic mineral huntite (H5) and polymeric additives synthesized in the present work into a polymeric formulation. In order to improve the dispersio...
Hemoglobin is essential for maintaining cellular bioenergetic homeostasis through its ability to bind and transport oxygen to the tissues. Besides its ability to transport oxygen, hemoglobin within erythrocytes plays an important role in cellular sig...
The production of oxygenated bio-additives for traditional fuels represents a key challenge due to their depletion in the near-future and their positive contribution to the reduction in environmental pollution. The present study considers the synthes...
The detrimental effect of nitrogen and oxygen when it comes to the precipitation of the strengthening γ’’ and γ’ phases in Alloy 718 is well-known from traditional manufacturing. Hence, the influence of the two processing atmospheres, namely argon an...
Additive manufacturing processes are among the most innovative manufacturing processes of this century. Powder-based direct metal deposition (DMD) is one of these processes. In the DMD process, local shielding takes place via the powder nozzle. The p...
Directed Energy Deposition (DED) is an additive manufacturing technology rapidly consolidating for the fabrication and repair of complex aerospace Ti-6Al-4V components, ensuring high deposition rates and large build volumes. However, in high build-ra...
The effect of Nb content on microstructure, mechanical properties and superelasticity was investigated for a series of Ti-xNb alloys, fabricated by the laser engineered net shaping method, using elemental Ti and Nb powders. The microstructure of as-d...
Vanadium extraction process demands low residual vanadium and carbon loss, and variations of dissolved elements in hot metal must be determined to achieve it. A three parts dynamic model that applies the concept of Gibbs’ free energy minimizati...
The design of bipolar plates is critical for improving the performance of proton exchange membrane fuel cells (PEMFCs). In this research, a new additional outlet based on a PEMFC’s parallel flow field was proposed, and three different positions of ou...
Hybrid systems composed of the reduced graphene oxide-supported platinum and multiwalled carbon nanotube-supported iridium (both noble metals utilized at low loadings on the level of 15 and ≤2 µg cm−2, respectively) were considered as...
Initiating the partial nitritation and anammox (PN/A) process without inoculation poses a significant challenge. Thus, there is a notable amount of interest in devising a straightforward strategy for the start-up of PN/A. This study demonstrates the...
PdPt bimetallic nanoparticles on carbon-based supports functioning as advanced electrode materials have attracted attention due to their low content of noble metals and high catalytic activity for fuel cell reactions. Glassy carbon (GC)-supported Pt...
Additive manufacturing (AM) technologies have advanced from rapid prototyping to becoming viable manufacturing solutions, offering users both design flexibility and mechanical properties that meet ISO/ASTM standards. Powder bed fusion using a laser b...
Betulinic acid (BA) was used as starting building block to create a library of novel BA-derived compounds containing O- and N-heterocycles. Firstly, BA was converted into methyl betulonate (BoOMe), which was used as intermediate in the developed meth...
The depletion of fossil fuels has heightened research and utilization of renewable energy such as biodiesel. However, this has thrown up another challenge of significant increase in its byproduct, glycerol. In view of the characteristics and potentia...
Marine viruses are important components of microbial communities and influence their structure and dynamics, yet their variability remains poorly documented in the northwestern Arabian Gulf. Virus-like particle (VLP) abundance was monitored over four...
Nanocrystalline diamond (NCD) films are attractive for many applications due to their smooth surfaces while holding the properties of diamond. However, their growth rate is generally low using common Ar/CH4 with or without H2 chemistry and strongly d...
Taurine (Tau) is an amino sulfonic acid, which is widely distributed in animal tissues, whereas it is almost lacking in plants with the exception of certain algae, seaweeds, and few others. In the aquafeed industry, Tau is mainly used as a feed addit...
Room-temperature ionic liquids (RTILs) have attracted attention in engineering electrolytes for electrochemical energy conversion and storage devices. Within the present study, five different RTILs were prepared and subsequently investigated as addit...
Biomass gasification is a relevant option to produce a gaseous fuel, it faces, however, several barriers regarding its quality for energetic applications. Therefore, in this study, air-steam and O2-enriched air mixtures were used as gasification agen...
Ultra-low-phosphorus high-purity iron (ULP-HPFe) is essential for advanced electromagnetic, aerospace, and defense systems, yet stabilizing basic-oxygen-furnace (BOF) dephosphorization remains challenging. To address this instability, we present an i...
Additive manufacturing provides a fabrication route for electrode components with controlled macrostructure; however, printable carbon inks that also incorporate oxygen reduction reaction active precursors remain underdeveloped. Here, XC-72 carbon wa...
Emissions from diesel engines can be limited and potentially decreased by modifying the fuel chemical composition through additive insertion. One class of additives that have shown to be particularly efficient in the reduction of the particulates fro...
Titanium dioxide (TiO2) nanoparticles are widely used in cosmetics, sunscreens, biomedicine, and food products. When used as a food additive, TiO2 nanoparticles are used in significant amounts as white food-coloring agents. However, the effects of Ti...
Photocatalysis is a powerful advanced oxidation process for water remediation, yet benchmarking has disproportionately relied on model organic dye pollutants under idealized conditions—overstating practical performance and obscuring mechanistic...
The deprotonation of an organic substrate is a common preactivation step for the enzymatic cofactorless addition of O
Biodiesel is one of the most attractive sources of clean energy. It is produced by the transformation of vegetable oils with up to 10% formation of glycerol as a by-product. Therefore, development of new approaches for processing bio-glycerol into su...
In this study, we investigated the impact of polyvinyl alcohol (PVA) incorporation on the optical properties and oxygen detection performance of a titanium dioxide/methylene blue (TiO2/MB) nanocomposite colorimetric indicator for packaging applicatio...
Several Ru-Ti oxide-based catalysts were investigated for the catalytic oxidation of HCl to Cl2 in this work. The active component RuO2 was loaded on different titanium-containing supports by a facile wetness impregnation method. The Ru-Ti oxide base...
This study investigates the improvement of combustion performance, engine emissions, energy, exergy, and thermodynamic efficiencies by adding oxygenated additives to diesel/biodiesel blends. Five different fuel mixtures (D100, D80B20, D50B50, D30B50S...
O2 is essential for the life of eukaryotic cells. The ability to sense oxygen availability and initiate a response to adapt the cell to changes in O2 levels is a fundamental achievement of evolution. The key switch for adaptation consists of the tran...
of 188