Skip to Content

520 Results Found

  • Article
  • Open Access
41 Citations
5,518 Views
23 Pages

Effect of ECAP on the Plastic Strain Homogeneity, Microstructural Evolution, Crystallographic Texture and Mechanical Properties of AA2xxx Aluminum Alloy

  • M. El-Shenawy,
  • Mohamed M. Z. Ahmed,
  • Ahmed Nassef,
  • Medhat El-Hadek and ,
  • Bandar Alzahrani,
  • Yasser Zedan and
  • W. H. El-Garaihy
  • + 2 authors+ 0 author

9 June 2021

This study presents a comprehensive evaluation of Equal Channel Angular Pressing (ECAP) processing on the structural evolution and mechanical properties of AA2xxx aluminum alloy. Finite element analysis (FE) was used to study the deformation behavior...

  • Article
  • Open Access
2 Citations
1,858 Views
19 Pages

8 December 2024

The aim of this study was the synthesis of intermetallic crystal dispersion in an ultra-fine-grained (UFG) aluminum matrix by the equal-channel angular pressing (ECAP) process, which provides severe plastic deformation (SPD) of aluminum-5 and 10% wt....

(This article belongs to the Section Materials for Energy Applications)
  • Article
  • Open Access
7 Citations
2,840 Views
14 Pages

11 September 2020

The research and development of modern metallic materials goes hand in hand with increasing their lifetime via optimized deformation processing. The presented work deals with preparation of an Al/Cu clad composite with implemented reinforcing Cu wire...

(This article belongs to the Special Issue Mechanical Properties in Progressive Mechanically Processed Metallic Materials)
  • Article
  • Open Access
1 Citations
2,214 Views
23 Pages

7 February 2025

Light Field Angular Super-Resolution (LFASR) addresses the issue where Light Field (LF) images can not simultaneously achieve both high spatial and angular resolution due to the limited resolution of optical sensors. Since Spatial-Angular Correlation...

(This article belongs to the Section Optical Sensors)
  • Article
  • Open Access
35 Citations
3,186 Views
31 Pages

11 August 2022

Magnesium-Zinc-Zirconium (Mg-Zn-Zr) alloys have caught considerable attention in medical applications where biodegradability is critical. The combination of their good biocompatibility, improved strength, and low cytotoxicity makes them great candida...

(This article belongs to the Special Issue Magnesium and Its Alloys as Biodegradable Implants)
  • Article
  • Open Access
11 Citations
3,471 Views
30 Pages

Improving Pure Titanium’s Biological and Mechanical Characteristics through ECAP and Micro-Arc Oxidation Processes

  • Dawit Bogale Alemayehu,
  • Masahiro Todoh,
  • Jang-Hsing Hsieh,
  • Chuan Li and
  • Song-Jeng Huang

31 July 2023

Pure titanium is limited to be used in biomedical applications due to its lower mechanical strength compared to its alloy counterpart. To enhance its properties and improve medical implants feasibility, advancements in titanium processing technologie...

(This article belongs to the Section B: Biology and Biomedicine)
  • Article
  • Open Access
10 Citations
4,059 Views
22 Pages

19 October 2023

As the efficiency of advanced aero engines improves, the operational speed of their rotors increases. This heightened operational speed makes the rotor dynamics highly sensitive to changes in the rotor’s mass asymmetry state, or unbalance state...

(This article belongs to the Special Issue Symmetry in Mechanical Engineering: Properties and Applications)
  • Article
  • Open Access
1 Citations
2,040 Views
16 Pages

26 July 2023

As one of the common techniques for measuring coseismic deformations, optical image correlation techniques are capable of overcoming the drawbacks of inadequate coherence and phase blurring which can occur in radar interferometry, as well as the prob...

(This article belongs to the Section Remote Sensors)
  • Article
  • Open Access
6 Citations
5,699 Views
13 Pages

12 November 2015

Twin roll cast Al-Mn- and Al-Mn-Zr-based alloys were subjected to four passes of equal channel angular pressing. The resulting grain size of 400 nm contributes to a significant strengthening at room temperature. This microstructure is not fully stabl...

(This article belongs to the Section Advanced Materials Characterization)
  • Article
  • Open Access
9 Citations
2,931 Views
11 Pages

3 November 2020

In this study, Al5083 alloy was deformed through equal-channel angular pressing (ECAP) up to three passes. The ECAP was conducted at room temperature in a mold using route C. The microstructure evolution was investigated under optical microscopic obs...

(This article belongs to the Section Materials Science and Engineering)
  • Article
  • Open Access
9 Citations
3,434 Views
13 Pages

26 July 2023

In the present study, the microstructure, mechanical properties, and stored energy of an aluminum alloy containing iron-rich fine precipitates, subjected to severe plastic deformation through equal-channel angular pressing (ECAP), were investigated u...

(This article belongs to the Special Issue Microstructure and Mechanical Behaviour of Structural Materials)
  • Article
  • Open Access
13 Citations
3,352 Views
14 Pages

Soft Elastomeric Capacitor for Angular Rotation Sensing in Steel Components

  • Han Liu,
  • Simon Laflamme,
  • Jian Li,
  • Caroline Bennett and ,
  • William N. Collins,
  • Austin Downey,
  • Paul Ziehl and
  • Hongki Jo
  • + 3 authors+ 0 author

23 October 2021

The authors have previously proposed corrugated soft elastomeric capacitors (cSEC) to create ultra compliant scalable strain gauges. The cSEC technology has been successfully demonstrated in engineering and biomechanical applications for in-plane str...

(This article belongs to the Section Sensor Networks)
  • Review
  • Open Access
1,304 Views
20 Pages

4 August 2026

Background and Objectives: Angular and rotational lower limb alignment concerns are a frequent reason for paediatric consultations. In most children, these findings reflect physiological developmental patterns that resolve spontaneously, but unilater...

(This article belongs to the Section Orthopedics)
  • Article
  • Open Access
11 Citations
3,898 Views
11 Pages

Designing (Ultra)Fine-Grained High-Entropy Alloys by Spark Plasma Sintering and Equal-Channel Angular Pressing

  • Lisa-Marie Rymer,
  • Thomas Lindner,
  • Philipp Frint,
  • Martin Löbel and
  • Thomas Lampke

18 December 2020

Single-phase, face-centered cubic (FCC) high-entropy alloys (HEA) are promising materials for future applications. In order to improve the mechanical properties, especially the tensile strength of these materials, this study focuses on the combinatio...

(This article belongs to the Section Crystalline Metals and Alloys)
  • Article
  • Open Access
6 Citations
3,796 Views
12 Pages

Potential of High Compressive Ductility of Ultrafine Grained Copper Fabricated by Severe Plastic Deformation

  • Mayu Asano,
  • Motohiro Yuasa,
  • Hiroyuki Miyamoto,
  • Tatsuya Tanaka and ,
  • Can Erdogan and
  • Tuncay Yalçinkaya
  • + 1 author+ 0 author

11 November 2020

Severe plastic deformation (SPD) can fabricate high-strength materials by forming an ultrafine grained (UFG) microstructure. Low elongation to failure of UFG materials in tensile tests, which has often been regarded as a measure of ductility of mater...

  • Article
  • Open Access
13 Citations
3,136 Views
10 Pages

Effect of ECAP Die Angle on Mechanical Properties and Biocompatibility of SS316L

  • Dayangku Noorfazidah Awang Sh’ri,
  • Zahiruddeen Salam Zahari and
  • Akiko Yamamoto

24 September 2021

In this study, ultrafine grain (UFG) SS316L was produced using an equal channel angular pressing (ECAP) process at two different die angles namely 120° and 126°. The effect of different die angles on mechanical, corrosion, and surface properties were...

(This article belongs to the Section Biobased and Biodegradable Metals)
  • Article
  • Open Access
4 Citations
3,036 Views
11 Pages

2 August 2024

The paleopathological literature notably lacks the description and analysis of distal humeral fractures and their associated complications. The objectives of this study were (1) to evaluate a distal humerus fracture associated with cubitus valgus obs...

  • Article
  • Open Access
14 Citations
5,352 Views
9 Pages

Risk Factor Analysis for Growth Arrest in Paediatric Physeal Fractures—A Prospective Study

  • Nikki Hooper,
  • Liam Johnson,
  • Nicole Banting,
  • Rubini Pathy and ,
  • Emily K. Schaeffer,
  • Jeffrey N. Bone,
  • Bryn O. Zomar,
  • Ash Sandhu,
  • Caitlyn Siu and
  • Kishore Mulpuri
  • + 7 authors+ 2 authors

16 May 2024

Background: Fractures through the physis account for 18–30% of all paediatric fractures, leading to growth arrest in up to 5.5% of cases. We have limited knowledge to predict which physeal fractures result in growth arrest and subsequent deform...

(This article belongs to the Special Issue Evidence-Based Medicine in the Practice of Orthopedics and Trauma Care: Current Status and Future Challenges)
  • Article
  • Open Access
2 Citations
3,834 Views
23 Pages

27 April 2024

The thin-walled rings of the RV reducer main bearings are prone to structural elastic deformation, which can significantly change the bearing mechanical characteristics. According to the actual assembly state of the RV reducer, the simulation model o...

(This article belongs to the Special Issue Advances and Challenges in Reliability and Maintenance Engineering)
  • Article
  • Open Access
11 Citations
2,960 Views
17 Pages

Spall Failure of ECAE Mg-Al Alloys at Extreme Strain Rates: Influence of a Refined Precipitate and Grain Microstructure

  • Christopher S. DiMarco,
  • Peter Lim,
  • Debjoy Mallick,
  • Laszlo Kecskes and ,
  • Timothy P. Weihs and
  • K. T. Ramesh
  • + 1 author+ 0 author

22 February 2023

The development of advanced materials for extreme dynamic environments requires an understanding of the links between the microstructure and the response of the material (i.e., Materials-by-Design). Spall failure significantly limits material perform...

(This article belongs to the Special Issue Dynamic Response of Metals under Extreme Conditions)
  • Article
  • Open Access
4 Citations
2,191 Views
18 Pages

20 December 2024

The evolution of the crystallographic texture after severe plastic deformation (SPD) of the aluminum alloy AA7075, commonly used in the aeronautical and automotive industries, depends on the parameters of the applied deformation process. In this pape...

(This article belongs to the Section Computation and Simulation on Metals)
  • Article
  • Open Access
75 Citations
10,429 Views
17 Pages

Enhanced Mechanical Properties and Electrical Conductivity in Ultrafine-Grained Al 6101 Alloy Processed via ECAP-Conform

  • Maxim Murashkin,
  • Andrey Medvedev,
  • Vil Kazykhanov,
  • Alexander Krokhin and ,
  • Georgy Raab,
  • Nariman Enikeev and
  • Ruslan Z. Valiev
  • + 2 authors+ 0 author

20 November 2015

This paper studies the effect of equal channel angular pressing-Conform (ECAP-C) and further artificial aging (AA) on microstructure, mechanical, and electrical properties of Al 6101 alloy. As is shown, ECAP-C at 130 °C with six cycles resulted in t...

(This article belongs to the Special Issue Ultrafine-grained Metals)
  • Article
  • Open Access
18 Citations
6,042 Views
13 Pages

22 July 2015

This work presents the mechanical behavior modeling of commercial purity titanium subjected to severe plastic deformation (SPD) during post-SPD compression, at temperatures of 600-900 °C and at strain rates of 0.001-0.1 s−1. The flow response of the...

(This article belongs to the Special Issue Ultrafine-grained Metals)
  • Editorial
  • Open Access
12 Citations
4,682 Views
4 Pages

11 April 2018

Academia and industry alike are faced with an ever-growing demand for energy-efficiency and reduced mass [...]

(This article belongs to the Special Issue Scientific and Engineering Progress on Aluminum-Based Light-Weight Materials: Research Reports from the German Collaborative Research Center 692)
  • Article
  • Open Access
34 Citations
6,635 Views
15 Pages

12 February 2020

This paper presents a state-of-the-art and a retrospective view of the critical stages in the evolution of equal-channel angular extrusion (ECAE) from the original idea to a cost-effective industrial technology. These stages include optimization of t...

  • Article
  • Open Access
12 Citations
3,594 Views
13 Pages

28 May 2020

This paper reports the effect of the processing route on the microstructure and mechanical properties in the pure copper sheets processed by single-roll angular-rolling (SRAR). The SRAR process was repeated up to six passes in two processing routes,...

(This article belongs to the Special Issue Materials by Non-traditional Methods of Severe Plastic Deformation (Spd))
  • Article
  • Open Access
2,195 Views
15 Pages

19 September 2023

Large values and gradients of stress and strain, triggering concentrated stress and strain, arise in angular areas of a structure. The strain action, leading to the finite loss of contact between structural elements, also triggers concentrated stress...

(This article belongs to the Section Mathematical Analysis)
  • Article
  • Open Access
24 Citations
3,233 Views
35 Pages

Optimizing the ECAP Parameters of Biodegradable Mg-Zn-Zr Alloy Based on Experimental, Mathematical Empirical, and Response Surface Methodology

  • Majed O. Alawad,
  • Abdulrahman I. Alateyah,
  • Waleed H. El-Garaihy,
  • Amal BaQais and ,
  • Sally Elkatatny,
  • Hanan Kouta,
  • Mokhtar Kamel and
  • Samar El-Sanabary
  • + 3 authors+ 0 author

2 November 2022

Experimental investigations were conducted on Mg-3Zn-0.6Zr alloy under different ECAP conditions of number of passes, die angles, and processing route types, aimed at investigating the impact of the ECAP parameters on the microstructure evolution, co...

(This article belongs to the Special Issue Forming Technologies and Mechanical Properties of Advanced Materials)
  • Article
  • Open Access
23 Citations
2,853 Views
24 Pages

The Effect of ECAP Processing Conditions on Microstructural Evolution and Mechanical Properties of Pure Magnesium—Experimental, Mathematical Empirical and Response Surface Approach

  • Abdulrahman I. Alateyah,
  • Waleed H. El-Garaihy,
  • Majed O. Alawad,
  • Samar El Sanabary and ,
  • Sally Elkatatny,
  • Hany A. Dahish and
  • Hanan Kouta
  • + 2 authors+ 0 author

2 August 2022

In this study, a quantitative evaluation approach was used to investigate how certain ECAP processing parameters affect the microstructural evolution, Vicker’s microhardness values and tensile properties of pure Mg. The ECAP processing paramete...

(This article belongs to the Section Metals and Alloys)
  • Article
  • Open Access
188 Views
11 Pages

31 October 2026

This retrospective cohort study compared antebrachial angular change following radioulnar diaphyseal fracture repair in immature small-breed dogs treated with or without concurrent ulnar ostectomy (UO). Medical records of small-breed dogs younger tha...

  • Review
  • Open Access
217 Views
22 Pages

27 September 2026

Equal Channel Angular Pressing (ECAP) technique is widely used to refine grains in metallic materials, including magnesium and its alloys. This paper reviews the grain refinement data for various magnesium alloys achieved through ECAP processing. The...

(This article belongs to the Special Issue Non-ferrous Metal Metallurgy and Its Cleaner Production)
  • Article
  • Open Access
12 Citations
2,567 Views
16 Pages

Influence of Long-Term Immersion Tests on the Electrochemical Corrosion Behavior of an Ultrafine-Grained Aluminum Alloy

  • Guilherme dos Santos Vacchi,
  • Danielle Cristina Camilo Magalhães,
  • Cristie Luis Kugelmeier,
  • Rodrigo da Silva and ,
  • Anibal de Andrade Mendes Filho,
  • Andrea Madeira Kliauga and
  • Carlos Alberto Della Rovere
  • + 2 authors+ 0 author

11 December 2024

The long-term corrosion resistance of commercially pure aluminum (AA1050) processed by equal channel angular pressing (ECAP) was evaluated in a saline environment. The study compared the microstructure and corrosion behavior of ECAP-processed samples...

(This article belongs to the Section Corrosion and Protection)
  • Case Report
  • Open Access
350 Views
14 Pages

Three-Dimensional Planning and Surgical Correction of Bilateral Developmental Valgus Deformity of the Manus in a Dog

  • Francesca P. Solari,
  • Mu Young Kim,
  • Federico R. Vilaplana Grosso,
  • Adam H. Biedrzycki and
  • Daniel D. Lewis

17 September 2026

A one-year-old, 48 kg, male neutered, Great Dane presented for bilateral thoracic limb lameness ascribed to an apparent developmental valgus deformity of both manus. Corrective radial-shaped osteotomies of the four weight-bearing metacarpal bones (II...

(This article belongs to the Special Issue Applications of 3D Printing in Veterinary Medicine)
  • Article
  • Open Access
324 Views
14 Pages

24 September 2026

Surgical adhesives may provide an alternative to postoperative bandaging, but their use has not been evaluated in veterinary medicine. This prospective pilot study investigated the tolerance and postoperative adhesion of a UV-polymerizable methacryla...

(This article belongs to the Section Equids)
  • Article
  • Open Access
22 Citations
3,457 Views
20 Pages

Investigation of Severe Plastic Deformation Effects on Magnesium RZ5 Alloy Sheets Using a Modified Multi-Pass Equal Channel Angular Pressing (ECAP) Technique

  • Partha Sarathi Sahoo,
  • Manas Mohan Mahapatra,
  • Pandu Ranga Vundavilli,
  • Rama Krushna Sabat and ,
  • Sachin Sirohi and
  • Sanjeev Kumar
  • + 1 author+ 0 author

21 July 2023

The present study investigates the effects of multiple passes of equal channel angular pressing (ECAP) on magnesium alloy sheets with the assistance of an Inconel plunger along with a die setup having a channel angle of 120° and corner angle of 1...

(This article belongs to the Section Metals and Alloys)
  • Article
  • Open Access
2 Citations
6,403 Views
13 Pages

Development of Bionic Semicircular Canals and the Sensation of Angular Acceleration

  • Zhi Wang,
  • Shien Lu,
  • Xianjin Wang,
  • Yuhang Chen and ,
  • Junjie Gong,
  • Yani Jiang and
  • Yixiang Bian
  • + 2 authors+ 0 author

To study the sensing process of the human semicircular canals (HSCs) during head rotation, which is difficult to directly measure due to physiological reasons. A 1-BSC (one-dimensional bionic semicircular canal) and 3-BSC were prepared with soft SMPF...

  • Article
  • Open Access
4 Citations
3,706 Views
14 Pages

7 September 2019

In this study we presented a theoretical investigation of the channeling of high energy protons with the radial deformed (10, 0)@(5, 0) double-wall carbon nanotubes (DWNTs). Proton energy is varied from 0.1 to 10 GeV. The channeling potential within...

(This article belongs to the Special Issue Atomic and Ionic Collisions with Formation of Quasimolecules)
  • Article
  • Open Access
22 Citations
4,329 Views
19 Pages

19 March 2020

In wire arc additive manufacturing (AM), as in arc welding, arc heat thermally deforms substrates and articles. For industrial applications, deformation characteristics of various materials must be understood and appropriate materials and methods of...

(This article belongs to the Special Issue Additive Manufacturing Methods and Modeling Approaches)
  • Article
  • Open Access
10 Citations
5,582 Views
14 Pages

22 December 2022

Using high-strength steel for offshore structures with a yield stress of 500 MPa, this study evaluated the distribution characteristics of welding residual stress in the thickness direction under the influence of constrained conditions during welding...

  • Article
  • Open Access
3 Citations
5,069 Views
36 Pages

26 December 2020

This paper introduces a system that can estimate the deformation process of a deformed flat object (folded plane) and generate the input data for a robot with human-like dexterous hands and fingers to reproduce the same deformation of another similar...

(This article belongs to the Section Sensors and Robotics)
  • Article
  • Open Access
29 Citations
4,444 Views
19 Pages

2 November 2019

This paper investigated the effects of aggregate mesostructures on permanent deformation behavior of an asphalt mixture using the three-dimensional (3D) discrete element method (DEM). A 3D discrete element (DE) model of an asphalt mixture composed of...

(This article belongs to the Special Issue Sustainable Designed Pavement Materials)
  • Article
  • Open Access
3 Citations
4,323 Views
13 Pages

18 November 2019

Thermal cycles and deformations during high-speed micro friction stir welding (μFSW) under different welding conditions were studied by experimental methods. The results show that the peak temperature and elevated-temperature exposure time (t150)...

(This article belongs to the Special Issue Advanced Process Technologies Based on Friction Stir Welding and Linear Friction Welding)
  • Tutorial
  • Open Access
7 Citations
8,971 Views
26 Pages

17 February 2022

The treatment of malunion of the lower extremity diaphysis is challenging. Diaphyseal osteotomies require extra care to promote bone healing. This may be enhanced through osteotomies, which do not produce bone gaps and allow for compression. The foca...

(This article belongs to the Special Issue Malunion of Fractures of the Lower Extremity)
  • Article
  • Open Access
13 Citations
7,208 Views
26 Pages

24 December 2022

Samples of polyethylene with extended-chain crystal morphology, obtained by crystallization under high pressure, were subjected to uniaxial compression to various strains. Accompanying structural changes were analyzed using scanning electron microsco...

(This article belongs to the Special Issue Plastics II)
  • Article
  • Open Access
2 Citations
184 Views

The Evaluation of Radiologic Angular Measurements in Patients with Foot Pain

  • Gulnihal Deniz,
  • Arzu Kaya,
  • Zubeyde Ercan,
  • Ahmet Kavakli and
  • Murat Ogeturk

The aim of this study was to investigate the relationship between foot deformities by comparing foot radiographs of patients with complaints of foot pain with those of healthy individuals. The study included 30 patients with pes cavus, 30 patients wi...

  • Article
  • Open Access
15 Citations
8,586 Views
25 Pages

20 August 2020

As a kind of common phenomenon in practical engineering, misalignment error considerably changes the working performance of bearing. However, it has rarely attracted attention in the study of duplex angular contact ball bearings (DACBBs). To evaluate...

(This article belongs to the Section Mechanical Engineering)
  • Article
  • Open Access
2 Citations
220 Views

Reproducibility and Reliability of the Radiographic Angles Used to Assess Tailor’s Bunions

  • David W. Shofler,
  • Bryon McKenna,
  • Johnny Huang and
  • Robert A. Christman

Background: Tailor’s bunion, or bunionette, deformity is a common condition of the lateral forefoot. To aid in assessing the deformity, radiographic angular measurements are frequently used. The objective of this study was to determine the reliabilit...

  • Article
  • Open Access
20 Citations
3,342 Views
18 Pages

Rationale for Processing of a Mg-Zn-Ca Alloy by Equal-Channel Angular Pressing for Use in Biodegradable Implants for Osteoreconstruction

  • Natalia S. Martynenko,
  • Natalia Yu. Anisimova,
  • Olga V. Rybalchenko,
  • Mikhail V. Kiselevskiy and ,
  • Georgy Rybalchenko,
  • Boris Straumal,
  • Diana Temralieva,
  • Almagul T. Mansharipova,
  • Aigul O. Kabiyeva and
  • Yuri Estrin
  • + 7 authors+ 2 authors

12 November 2021

Widespread use of Mg-Zn-Ca alloys in clinical orthopedic practice requires improvement of their mechanical properties—in particular, ductility—and enhancement of their bioactivity for accelerated osteoreconstruction. The alloy was studied in two stru...

(This article belongs to the Special Issue Relationships between Processing and Properties of Magnesium-Based Alloys)
  • Article
  • Open Access
3,692 Views
10 Pages

Angular Rolling of the Hollow Flanges of Pipe Joints

  • Pavel Kononov,
  • Sergey Ignatiev,
  • Dmitry Levashov and
  • Irina Kononova

18 January 2021

The paper considers a three-stage technology for angular rolling of the pipe workpiece. This technology facilitates the expansion of the range of flange parts available by eliminating a number of drawbacks of the known methods of metal forming. In th...

(This article belongs to the Section Metal Casting, Forming and Heat Treatment)
  • Article
  • Open Access
14 Citations
6,437 Views
19 Pages

2 May 2019

Multi-layer welding involves the process of stacking many beads, so it requires much time and effort to predict the deformation through experimentation or numerical analysis. In this study, a systematic method for predicting transverse angular distor...

(This article belongs to the Special Issue Industrial Additive Manufacturing Process Planning: Process Evaluation, Metrology, and Post-Processing Techniques)

of 11