Skip to Content

6,465 Results Found

  • Article
  • Open Access
6 Citations
2,234 Views
14 Pages

Kinetic Study of the Aging and Overaging of Alloy Pb0.058%Ca0.12%Sr1.09%Sn for Battery Grids

  • Youssef Ait Yassine,
  • Marwan Lakhal,
  • Nabil Labchir,
  • Elhassan Zantalla and ,
  • Elmadani Saad and
  • Mohamed Sannad
  • + 1 author+ 0 author

1 September 2023

In this paper, we examine the effect of a small amount of Sn, Sr and Ca on the hardening and the kinetic properties of Pb. Experimentally, we analyze the specific process from the structural hardening evolution to equilibrium of PbCaSrSn alloy occurr...

(This article belongs to the Section Thin Films)
  • Article
  • Open Access
9 Citations
4,953 Views
15 Pages

7 November 2024

The effect of over-aging on the precipitation behavior and mechanical properties of an ultra-high-strength Al-Zn-Mg-Cu alloy was investigated using various over-aging treatment regimes. To reveal the influence of over-aging on matrix precipitation, n...

(This article belongs to the Special Issue Research and Application of High Entropy Alloys)
  • Feature Paper
  • Article
  • Open Access
13 Citations
5,904 Views
10 Pages

Effect of Zr Addition on Overaging and Tensile Behavior of 2618 Aluminum Alloy

  • Stefania Toschi,
  • Eleonora Balducci,
  • Lorella Ceschini,
  • Eva Anne Mørtsell and ,
  • Alessandro Morri and
  • Marisa Di Sabatino
  • + 1 author+ 0 author

26 January 2019

The effect of Zr addition on overaging and tensile behavior in a 2618 Al–Cu–Mg–Ni–Fe alloy has been investigated in this study. The chemical composition of the base 2618 alloy, containing ~0.1 wt % of Zr, was modified by addin...

(This article belongs to the Special Issue Alloys for High-Temperature Applications)
  • Feature Paper
  • Article
  • Open Access
5 Citations
2,948 Views
14 Pages

14 May 2021

Herein, a new kind of overaging strategy: two steps of overaging for tailor rolled blank of dual phase steel (DP-TRB) was investigated. The results indicate that two steps of the overaging process is a useful way to control the mechanical properties...

  • Article
  • Open Access
1 Citations
3,721 Views
10 Pages

Assessing Comparative Yield and Yield Contributing Traits of Hybrid Rice Varieties Transplanted as Over-Aged Seedlings in the South-Central Coastal Ecosystem of Bangladesh

  • Md. Ibrahim Khalil,
  • Md. Subbir Ahamed,
  • Uzzal Somaddar,
  • Hridoy Chandra Dey and ,
  • Sameera Mamun,
  • Uttam Kumer Sarker,
  • Md. Romij Uddin,
  • Mohammad Golam Mostofa and
  • Gopal Saha
  • + 4 authors+ 0 author

17 January 2025

The transplanting of over-aged seedlings is an important adaptive strategy for rice cultivation during the monsoon season in the coastal areas of Bangladesh. This study aimed to identify promising hybrid rice varieties that can be transplanted as ove...

  • Article
  • Open Access
2,391 Views
17 Pages

16 April 2024

Overage construction workers have received widespread attention due to the higher safety risk. The balance of interests among the contractor, supervisor, and regulator forms a game, whose dynamics are tightly linked to the contractor’s risk per...

(This article belongs to the Section Construction Management, and Computers & Digitization)
  • Article
  • Open Access
7 Citations
3,294 Views
19 Pages

Aging Behaviour of a 12.2Cr-10Ni-1Mo-1Ti-0.6Al Precipitation-Hardening Stainless Steel Manufactured via Laser Powder Bed Fusion

  • Alessandro Morri,
  • Mattia Zanni,
  • Lorella Ceschini,
  • Alessandro Fortunato and
  • Massimo Pellizzari

3 September 2023

The combination of precipitation-hardening stainless steels (PH-SS) and laser powder bed fusion (LPBF) enables the manufacturing of tools for plastic injection moulding with optimised geometry and conformal cooling channels, with potential benefits i...

(This article belongs to the Special Issue Advances in Additive Manufacturing and Their Applications)
  • Article
  • Open Access
6 Citations
2,482 Views
13 Pages

Influence of Annealing and Aging Parameters on the Microstructure and Properties of 1200 MPa Grade Cold-Rolled Dual-Phase Steel

  • Xiaoyue Ma,
  • Xiaohong Chu,
  • Yuebiao Yang,
  • Hongzhou Lu and ,
  • Wenjun Wang and
  • Zhengzhi Zhao
  • + 1 author+ 0 author

9 October 2024

With the rapid development of the automotive industry, the requirements for bodywork materials are not only focused on high strength but also on improved forming properties. To develop a new generation of automotive steels with higher strength–...

(This article belongs to the Special Issue Physical Metallurgy of Metals and Alloys (3rd Edition))
  • Article
  • Open Access
3 Citations
3,971 Views
11 Pages

30 July 2022

The continuously annealed low-carbon-steel strips from industrial production showed an average aging index of about 30 N/mm². This increase in yield strength caused by the continuous-annealing process was strongly dependent on the soaking temper...

(This article belongs to the Section Metal Casting, Forming and Heat Treatment)
  • Article
  • Open Access
2 Citations
2,820 Views
19 Pages

Investigating Physical, Social, Emotional, and Health Frailties of Cancer Survivors after Cancer Treatment: The Urgent Call for Tailored Multidisciplinary Survivorship Plans in Italy

  • Stefania Moramarco,
  • Luigi De Angelis,
  • Laura Bernardini,
  • Lorenza Marconi and ,
  • Gaia Piunno,
  • Simonetta Siciliano,
  • Andrea Malizia,
  • Ersilia Buonomo,
  • Alessia Pesaresi and
  • Francesco Torino
  • + 9 authors+ 4 authors

4 September 2024

Background: Understanding the specific needs of cancer survivors is essential for healthcare policy. In Italy, dedicated studies are lacking, so we aimed to investigate the physical, mental, social, and health difficulties encountered by these patien...

(This article belongs to the Special Issue Latest Advancements in Health-Related Quality of Life Research in Cancer Survivorship)
  • Article
  • Open Access
4 Citations
2,742 Views
18 Pages

16 November 2019

Windows with various colors are important design elements used widely ranging from traditional architecture to contemporary buildings to express the architectural façade, the interior atmosphere, and so on. Recently, there is a possibility tha...

(This article belongs to the Special Issue The Application of Renewable Energy in Sustainable Architecture)
  • Article
  • Open Access
27 Citations
6,823 Views
16 Pages

7 July 2018

The present work encompasses the effect of overaging on the strain-controlled low-cycle fatigue (LCF) behavior of an extruded AA6061 aluminum alloy at varying strain amplitudes. During the T7 aging treatment, the size of precipitates increased from 6...

  • Article
  • Open Access
9 Citations
2,181 Views
11 Pages

Enhancing Stress Corrosion Cracking Resistance of Low Cu-Containing Al-Zn-Mg-Cu Alloys by Aging Treatment Control

  • Ying Li,
  • Mingyang Yu,
  • Xiwu Li,
  • Kai Wen and ,
  • Lizhen Yan,
  • Kai Zhu and
  • Wei Xiao
  • + 2 authors+ 0 author

21 November 2024

The 7085 aluminum alloy with a low Cu content is an important lightweight structural material in the aerospace field due to its advantages of low density, high specific strength, and high hardenability. However, like other high-strength Al-Zn-Mg-Cu a...

  • Article
  • Open Access
19 Citations
5,842 Views
15 Pages

Effects of Aging Treatments on the Age Hardening Behavior and Microstructures in an Al-Mg-Si-Cu Alloy

  • Limei Liu,
  • Yingpeng Hou,
  • Tuo Ye,
  • Like Zhang and ,
  • Xuan Huang,
  • Yuqing Gong,
  • Chao Liu,
  • Yuanzhi Wu and
  • Shiyun Duan
  • + 4 authors+ 0 author

15 February 2024

In this study, we investigated the effects of modified aging treatments on the microstructures and hardness in a commercial 6016 Al alloy through hardness tests and transmission electron microscopy (TEM) observations. The results demonstrate that man...

(This article belongs to the Special Issue Aluminum Alloys: Structures, Properties and Applications)
  • Article
  • Open Access
2,363 Views
17 Pages

13 January 2026

The 6xxx series aluminum alloys are preferred in many industrial applications because they can achieve relatively high strength levels through heat treatment. It is known that, as in the case of the EN AW 6056 alloy, the addition of small amounts of...

(This article belongs to the Special Issue Processing, Microstructure and Properties of Aluminium Alloys)
  • Article
  • Open Access
3 Citations
2,344 Views
16 Pages

Microstructure and Deformation of Over-Aged Al-Zn-Mg-Cu Alloy with Fine Grains during Multiple Stress Relaxation Tests

  • Peng Rong,
  • Xin Fang,
  • Yakai Xiao,
  • Qian Wang and ,
  • Zeyu Bian,
  • Qing Yang,
  • Haowei Wang and
  • Zhe Chen
  • + 3 authors+ 0 author

6 December 2022

Strong obstacles can greatly impede the motion or transmission of dislocations, which can be reflected by strain rate sensitivity and activation volume. In this study, the strain rate sensitivity and activation volume of overaged Al-Zn-Mg-Cu alloys w...

  • Article
  • Open Access
2 Citations
1,734 Views
15 Pages

The Influence of Cu on the Aging Mechanical Properties and Precipitate Behavior of Si-Rich Al-Mg-Si Alloy

  • Yu Zhao,
  • Wu Wei,
  • Yi Lu,
  • Zhizheng Rong and ,
  • Shengping Wen,
  • Hui Huang and
  • Zuoren Nie
  • + 2 authors+ 0 author

23 October 2025

The influence of Cu addition on the age-hardening response, mechanical properties, and precipitation evolution of Si-rich Al–Mg–Si alloy was investigated by hardness test, room-temperature tensile test, and transmission electron microscop...

  • Article
  • Open Access
60 Citations
12,774 Views
16 Pages

17 November 2018

The aim of the present work is the study of T6 heat treatment of A354 (Al-Si-Cu-Mg) casting alloy. The heat treatment was optimized by maximizing mechanical strength of the alloy while keeping the treatment cost effective, reducing treatment time and...

(This article belongs to the Special Issue Heat Treatment of Aluminum Alloys)
  • Article
  • Open Access
33 Citations
7,545 Views
18 Pages

29 May 2018

Cast aluminum alloys are widely used in the automotive field for the production of complex engine parts. However, the mechanical properties of heat-treatable alloys (e.g., Al–Si–Mg or Al–Si–Cu–Mg) are negatively affected...

(This article belongs to the Special Issue Microstructure and Mechanical Properties of Casting Alloys)
  • Article
  • Open Access
3 Citations
2,484 Views
11 Pages

Effect of the Aging Process in the Failure Pressure Estimation in an API 5L Gr. B Cracked Pipeline Using Finite Element Modeling

  • Gerardo Terán,
  • Selene Capula-Colindres,
  • Julio C. Velázquez,
  • Noé E. González-Arévalo and ,
  • Esther Torres Santillán,
  • Daniel Angeles-Herrera and
  • Arturo Cervantes-Tobón
  • + 2 authors+ 0 author

1 January 2025

This work shows the effect of artificial aging on the mechanical properties of an API 5L Gr. B steel that undergoes different artificial aging times (0, 500, 1250, and 1500 h). Among the mechanical properties studied are the stress–strain curve...

(This article belongs to the Section Corrosion, Wear and Erosion)
  • Article
  • Open Access
18 Citations
3,509 Views
12 Pages

Effect of Post-Fabricated Aging on Microstructure and Mechanical Properties in Underwater Friction Stir Additive Manufacturing of Al–Zn–Mg–Cu Alloy

  • Ying Li,
  • Changshu He,
  • Jingxun Wei,
  • Zhiqiang Zhang and ,
  • Ni Tian,
  • Gaowu Qin and
  • Xiang Zhao
  • + 2 authors+ 0 author

7 May 2022

The fabricated Al–Zn–Mg–Cu alloy build has low mechanical properties due to the dissolution of strengthening precipitates back into the matrix during friction stir additive manufacturing (FSAM). Post-fabricated aging was considered...

(This article belongs to the Special Issue Additive Manufacturing (AM) of Metal Alloys: Microstructure and Mechanical Performance)
  • Article
  • Open Access
3,199 Views
26 Pages

27 January 2025

A modified carbide-free bainite (CFB) steel has been developed, building on existing alloys for compatibility with commercial continuous annealing lines (CALs), featuring a low austenitization temperature and short overaging time. The microstructural...

(This article belongs to the Special Issue Phase Transformation and Softening Mechanisms of Metals and Alloys during Thermomechanical Processing)
  • Article
  • Open Access
35 Citations
14,305 Views
11 Pages

2 April 2016

Tensile tests were conducted on both as-quenched and over-aged 7050 aluminum alloy to investigate the effect of heat treatment on the in-plane anisotropy of as-rolled 7050 aluminum alloy. The results showed that the tensile direction has limited effe...

(This article belongs to the Special Issue Aluminum Alloys)
  • Article
  • Open Access
694 Views
29 Pages

Study on the Synergistic Effects of Pre-Deformation and Post-Aging Treatments on the Mechanical and Corrosion Properties of a 2A97 Al-Cu-Li Alloy

  • Danyang Liu,
  • Bangguo Wu,
  • Xin Liu,
  • Li Wang and ,
  • Hua Zhou,
  • Lei Tang,
  • Kefu Gan and
  • Jinfeng Li
  • + 3 authors+ 0 author

This work systematically investigates the effects of pre-deformation, post-aging temperature, and aging time on the mechanical properties, corrosion behavior, and microstructure of a 2A97 Al-Cu-Li alloy. Microstructural characterization indicates tha...

(This article belongs to the Topic Advances in Processing, Microstructure and Mechanical Properties of Lightweight Alloys)
  • Feature Paper
  • Article
  • Open Access
1 Citations
2,245 Views
7 Pages

Microstructural Influences Caused by Different Aging Strategies on the Strain-Dependent Damping of the High-Strength Aluminum Alloy AA7075

  • Steffen Lotz,
  • Jiali Zhang,
  • Emad Scharifi,
  • Roland Morak and ,
  • Ursula Weidig,
  • Jürgen Göken,
  • Christoph Broeckmann and
  • Kurt Steinhoff
  • + 3 authors+ 0 author

16 December 2022

The present study focused on the influence of different aging conditions on the strain-dependent damping of the high-strength aluminum alloy AA7075. For this purpose, different artificial aging strategies were carried out after solution heat treatmen...

  • Article
  • Open Access
4 Citations
2,980 Views
14 Pages

Microstructure and Texture Evolution of X85MnAl29-9 Steel During Aging

  • Małgorzata Witkowska,
  • Kinga Chronowska-Przywara,
  • Joanna Kowalska and
  • Anna Zielińska-Lipiec

19 November 2024

The research presented in this paper is part of a larger project concerning high-manganese alloys with different chemical compositions (mainly in manganese content from 21 to 31 wt.%). The presented examination results concern the analysis of the mic...

  • Article
  • Open Access
11 Citations
3,713 Views
13 Pages

3 September 2021

In this paper, the effects of an aging treatment on the corrosion resistance/mechanism of a tensile deformed Al-Cu-Mn-Fe-Zr alloy are investigated. The impedance magnitude and polarization resistance increase, while the corrosion current decreases wi...

(This article belongs to the Special Issue Commemorating the Launch of the Section 'Metals and Alloys')
  • Article
  • Open Access
3 Citations
3,690 Views
16 Pages

Microstructural and Mechanical Characterization of the Aging Response of Wrought 6156 (Al-Mg-Si) Aluminum Alloy

  • Nikolaos D. Alexopoulos,
  • Joseph D. Robson,
  • George Stefanou,
  • Vasileios Stergiou and ,
  • Alexandra Karanika and
  • Stavros K. Kourkoulis
  • + 1 author+ 0 author

24 August 2022

The impact of the artificial aging response on the microstructure and tensile mechanical properties of aluminum alloy 6156 was investigated. Specimens were artificially aged at three different artificial aging temperatures and for various holding tim...

  • Article
  • Open Access
5 Citations
2,618 Views
16 Pages

3 May 2024

Strain-controlled low cycle fatigue (LCF) tests were conducted on conventionally grained (CG) and ultrafine-grained (UFG) Al-Mg-Si alloys treated under various aging conditions. In the cyclic stress response (CSR) curves, CG peak-aged (PA) alloys sho...

(This article belongs to the Special Issue Advances in Materials Processing (3rd Edition))
  • Article
  • Open Access
5 Citations
2,601 Views
27 Pages

The Role of Mg Content and Aging Treatment on the Tensile and Fatigue Properties of Die-Cast 380 Alloy

  • Agnes M. Samuel,
  • Yasser Zedan,
  • Ehab A. Elsharkawi,
  • Mohamed H. Abdelaziz and
  • Fawzy H. Samuel

11 December 2022

The main objective of this contribution was to determine the impact of magnesium (Mg) concentration and solidification rate (about 800 °C/s) on the mechanical properties of commercial A380.1 die-cast alloy. Respective amounts of 0.10%, 0.30%, and...

(This article belongs to the Special Issue Research and Modeling of Materials Fatigue and Fracture)
  • Article
  • Open Access
1 Citations
2,989 Views
17 Pages

31 March 2024

Thin-walled Al-Mg-Si alloy profiles with different compositions and aging states were prepared using the heating and extrusion process. The properties and structure of the profiles were then investigated using a metallographic microscope, scanning el...

(This article belongs to the Section Materials Science and Engineering)
  • Article
  • Open Access
1 Citations
1,431 Views
19 Pages

Effect of Silicon and Continuous Annealing Process on the Microstructure, Mechanical Properties, and Hydrogen Embrittlement of DP1500 Steel

  • Wei Li,
  • Yu Tang,
  • Boyu Cao,
  • Yeqian Jiang and ,
  • Yang Shen,
  • Wei Li and
  • Ke Zhang
  • + 2 authors+ 0 author

19 December 2025

Dual-phase (DP) steels are widely used in automotive structures due to their excellent strength–ductility balance. This study examines how silicon content and continuous annealing parameters affect the microstructure, mechanical properties, and...

(This article belongs to the Special Issue Alloy Strengthening Mechanisms, Microstructure Control and Performance Optimization (Second Edition))
  • Article
  • Open Access
5 Citations
3,021 Views
15 Pages

Analysis of a Double Aging Process in a Maraging 300 Steel Fabricated by Selective Laser Melting, Using the Design of Experiments Technique

  • Inés Pérez-Gonzalo,
  • Alejandro González-Pociño,
  • Florentino Alvarez-Antolin and
  • Laura del Rio-Fernández

6 October 2023

This study aims to optimize the aging treatment of a maraging 300 steel, without prior austenitizing, manufactured by the selective laser melting (SLM) technique. The study includes the analysis of a double aging process. In addition, the impact of t...

(This article belongs to the Section Metal Failure Analysis)
  • Article
  • Open Access
8 Citations
3,164 Views
15 Pages

30 November 2023

This paper examines the optimal aging temperature of WE43 alloy that has undergone precipitation hardening in conjunction with deep cryogenic treatment. The microstructure and phase composition were investigated, a microanalysis of the chemical compo...

(This article belongs to the Special Issue Research on the Microstructure and Properties of Metal Alloys)
  • Article
  • Open Access
1 Citations
1,099 Views
16 Pages

The Effect of NbC Precipitates on Hydrogen Embrittlement of Dual-Phase Steels

  • Wei Li,
  • Kejia Qiang,
  • Boyu Cao,
  • Yu Tang and ,
  • Fengcang Ma,
  • Wei Li and
  • Ke Zhang
  • + 2 authors+ 0 author

7 December 2025

New grades of dual-phase (DP) steels with ultimate tensile strength (UTS) up to 1500 MPa have been developed using a continuous annealing process. This study investigates the effects of over-aging temperature and NbC precipitates on the microstructur...

(This article belongs to the Special Issue Advances in Corrosion and Failure Analysis of Metallic Materials)
  • Article
  • Open Access
2 Citations
1,412 Views
17 Pages

Laser Powder Bed-Fused Scalmalloy®: Effect of Long Thermal Aging on Hardness and Electrical Conductivity

  • Emanuele Ghio,
  • Lorenzo Curti,
  • Daniele Carosi,
  • Alessandro Morri and
  • Emanuela Cerri

11 December 2025

This study investigates the microstructural evolution, porosity characteristics, and mechanical behavior of LPBF-manufactured Scalmalloy®, which were investigated in the as-built conditions and after long-term exposure to direct aging of 275, 325...

(This article belongs to the Special Issue Recent Advances in Powder-Based Additive Manufacturing of Metals)
  • Article
  • Open Access
27 Citations
4,585 Views
17 Pages

Mechanism of Precipitate Microstructure Affecting Fatigue Behavior of 7020 Aluminum Alloy

  • Zhaojun Shan,
  • Shengdan Liu,
  • Lingying Ye,
  • Yiran Li and ,
  • Chunhua He,
  • Jin Chen,
  • Jianguo Tang,
  • Yunlai Deng and
  • Xinming Zhang
  • + 4 authors+ 0 author

22 July 2020

The effect of different precipitate microstructures obtained by different heat treatments on fatigue behavior of 7020 aluminum alloy was investigated. The fine Guinier Preston I (GPI) zones in the under-aged alloy can be repeatedly sheared by disloca...

  • Article
  • Open Access
2 Citations
622 Views
23 Pages

Comparative Study on the Corrosion Sensitivity and Microstructure of 15%SiCp/Al-Cu-Mg Aluminum Matrix Composites Under Different Aging Treatments

  • Nan Guo,
  • Zhiyong Li,
  • Ran Pan,
  • Yuansong Zeng and ,
  • Pingan Xu,
  • Yunhe Chang and
  • Baosheng Liu
  • + 2 authors+ 0 author

29 April 2026

A comparative investigation of the corrosion behavior evolution of 15%SiCp/Al-Cu-Mg aluminum matrix composites (AMC) subjected to different heat treatments in a salt spray environment containing 5wt% NaCl was performed. Metallographic microscopy was...

(This article belongs to the Special Issue Corrosion Behavior and Mechanical Properties of Metallic Materials (3rd Edition))
  • Article
  • Open Access
1 Citations
2,521 Views
22 Pages

19 October 2025

Understanding students’ feelings about daily school life can be a tool for schools to enhance their learning experience and sense of belonging. Despite the abundant research on achievement and engagement, few studies jointly examine the effect...

(This article belongs to the Section Education and Psychology)
  • Article
  • Open Access
9 Citations
3,268 Views
11 Pages

Decrease in Electrical Resistivity below 28 nΩm by Aging in Hyperperitectic Al-Zr Alloys Treated at High Temperatures

  • Florentino Alvarez-Antolin,
  • Zakariae Amghouz,
  • Alberto Cofiño-Villar,
  • Alejandro Gonzalez-Pociño and
  • Manuel G. Melero

23 July 2021

High-voltage and alternating current conductors are mainly made up of a steel core and an envelope made of aluminum wires. The alloys commonly used in the shell are of pure aluminum, which provides low electrical resistivity, but also low mechanical...

  • Review
  • Open Access
1,042 Views
20 Pages

Vitamin C Encapsulation in Dairy Foods: A Review

  • Mia Toronto,
  • Kristine Spence and
  • Owen M. McDougal

4 September 2026

Consumers are increasingly purchasing nutrient-dense, clean-label foods, a trend that is driving demand for vitamin C-fortified dairy products; however, vitamin C is readily degraded by heat, light, oxygen, and changes to pH. The propensity for vitam...

(This article belongs to the Section Milk Processing)
  • Article
  • Open Access
6 Citations
3,616 Views
12 Pages

Superplastic Behavior of Overaged 2024 Aluminum Alloy after Friction Stir Processing

  • Alberto Orozco-Caballero,
  • Marta Álvarez-Leal,
  • Fernando Carreño and
  • Oscar A. Ruano

3 November 2022

A commercial 2024 aluminum alloy was heat treated at 280 °C for 48 h and then slow cooled in a furnace to obtain minimum hardness. This material was then friction stir processed (FSP) using three sets of processing conditions. To study the effect...

(This article belongs to the Section Metal Casting, Forming and Heat Treatment)
  • Article
  • Open Access
8 Citations
3,557 Views
15 Pages

Effects of Magnesium Content and Age Hardening Parameters on the Hardness and Ultimate Tensile Strength of SiC-Reinforced Al-Si-Mg Composites

  • Ashwin Shetty,
  • Thirumaleshwara Bhat,
  • Sathyashankara Sharma,
  • Ananda Hegde and ,
  • Nithesh K,
  • Ravikantha Prabhu and
  • Gajanan Anne
  • + 2 authors+ 0 author

31 December 2024

This study investigates the effects of magnesium (Mg) content, silicon carbide (SiC) reinforcement, and aging temperature (AT) on the ultimate tensile strength (UTS) and Brinell hardness number (BHN) of eutectic Al-Si composites using a full factoria...

(This article belongs to the Section Metal Composites)
  • Article
  • Open Access
1 Citations
1,442 Views
12 Pages

Magnetic Indicator for Evaluating Cu Clustering and Hardening Effect in RPV Model Alloy

  • Wenqing Jia,
  • Qiwei Quan,
  • Wangjie Qian,
  • Chuang Bian and ,
  • Chaoliang Xu,
  • Jian Yin,
  • Bin Li,
  • Yuanfei Li,
  • Minyu Fan and
  • Haitao Wang
  • + 6 authors+ 1 author

28 August 2024

The reactor pressure vessel (RPV) is a critical barrier in nuclear power plants, but its embrittlement during service poses a significant safety challenge. This study investigated the effects of Cu-enriched clusters on the mechanical and magnetic pro...

(This article belongs to the Section Metal Casting, Forming and Heat Treatment)
  • Article
  • Open Access
11 Citations
3,172 Views
13 Pages

29 May 2023

A selective laser-melted Al–Mn–Sc alloy with 99.9% relative density has been obtained in this work through systematic process optimization. The as-fabricated specimen had the lowest hardness and strength, but the highest ductility. The ag...

(This article belongs to the Special Issue The Additive Manufacturing of Metallic Alloys)
  • Article
  • Open Access
3 Citations
2,881 Views
15 Pages

Precipitation Kinetics of Water-Cooled Copper Mold Al-Mg-Si(-Mn, Zr) Alloy during Aging

  • Hua Shen,
  • Jianchao Shi,
  • Yukun Zhou,
  • Xiaofeng Wang and
  • Guangchun Yao

29 November 2023

The aging precipitation behavior of 6061 aluminum alloy that underwent iron casting and water-cooled copper casting and 6061 aluminum with Mn and Zr elements added was studied. Firstly, the hardness curves, tensile properties, and fracture morphology...

(This article belongs to the Special Issue Advanced Metal Matrix Functional Composites and Applications)
  • Article
  • Open Access
6 Citations
5,455 Views
20 Pages

Stress Corrosion Cracking in an Extruded Cu-Free Al-Zn-Mg Alloy

  • Adrian Lervik,
  • John C. Walmsley,
  • Lars Lodgaard,
  • Calin D. Marioara and ,
  • Roy Johnsen,
  • Otto Lunder and
  • Randi Holmestad
  • + 2 authors+ 0 author

7 September 2020

Stress corrosion cracking (SCC) in Cu-free Al-Zn-Mg (7xxx) aluminium alloys limits its use in many applications. In this work, we study in detail the microstructure of a peak and slightly overaged condition in an AA7003 alloy using transmission- and...

  • Article
  • Open Access
10 Citations
2,561 Views
14 Pages

Effect of Heat Treatment on the Dry Sliding Wear Behavior of the Mg-3Zn-0.4Ca Alloy for Biodegradable Implants

  • Nuria Pulido-González,
  • Sonia García-Rodríguez,
  • Belén Torres and
  • Joaquin Rams

10 January 2023

The wear behavior of the Mg-3wt.% Zn-0.4wt.% Ca (ZX30) alloy was tested using a pin-on-disc configuration with AZ31 alloy discs as counterparts under dry sliding conditions. The ZX30 alloy was tested in different states: as-cast, solution-treated, pe...

(This article belongs to the Special Issue Advanced Magnesium Alloys: Processing, Microstructure, Property Control, and Sectors of Fabrication Technologies)
  • Proceeding Paper
  • Open Access
2 Citations
3,384 Views
6 Pages

This review focuses on the current situation of energy resources and usage in Mongolia in order to reduce the air pollution problems that are caused by the heavy and inefficient utilization of coal, which for instance causes 80% of the air pollution...

(This article belongs to the Proceedings of The 2nd International Electronic Conference on Forests—Sustainable Forests: Ecology, Management, Products and Trade)

of 130