Skip to Content

122 Results Found

  • Article
  • Open Access
18 Citations
6,254 Views
11 Pages

15 November 2018

In this study, we demonstrated the feasibility of a wireless strain sensor using resonant frequency modulation through tensile impedance test and wireless sensing test. To achieve a high stretchability, the sensor was fabricated by embedding a copper...

(This article belongs to the Special Issue Sensors for Gait, Posture, and Health Monitoring)
  • Article
  • Open Access
77 Citations
10,731 Views
12 Pages

High-Temperature SAW Wireless Strain Sensor with Langasite

  • Lin Shu,
  • Bin Peng,
  • Zhengbing Yang,
  • Rui Wang and ,
  • Senyang Deng and
  • Xingzhao Liu
  • + 1 author+ 0 author

11 November 2015

Two Surface acoustic wave (SAW) resonators were fabricated on langasite substrates with Euler angle of (0°, 138.5°, 117°) and (0°, 138.5°, 27°). A dipole antenna was bonded to the prepared SAW resonator to form a wireless sensor. The characteristics...

(This article belongs to the Special Issue Sensors for Harsh Environments)
  • Article
  • Open Access
10 Citations
3,795 Views
22 Pages

12 April 2023

Near-field passive wireless sensors can realize non-contact strain measurement, so these sensors have extensive applications in structural health monitoring. However, these sensors suffer from low stability and short wireless sensing distance. This p...

(This article belongs to the Special Issue Advanced Sensing and Evaluating Technology in Nondestructive Testing)
  • Article
  • Open Access
34 Citations
5,431 Views
10 Pages

Wireless Passive LC Temperature and Strain Dual-Parameter Sensor

  • Ya Wang,
  • Qiulin Tan,
  • Lei Zhang,
  • Baimao Lin and ,
  • Meipu Li and
  • Zhihong Fan
  • + 1 author+ 0 author

30 December 2020

There is an increasing demand for bearing temperature and strain monitoring in high-speed rotating systems. This study proposes a new multiresonance, multiplexing, wireless, passive inductance capacitance (LC) temperature and strain sensor. The senso...

(This article belongs to the Section E: Engineering and Technology)
  • Article
  • Open Access
38 Citations
5,646 Views
13 Pages

9 July 2020

Strain and crack are critical indicators of structural safety. As a novel sensing device, a patch antenna sensor can be utilized to wirelessly estimate structural strain and surface crack growth through resonance frequency shift. The main challenges...

(This article belongs to the Special Issue Innovative Sensors for Civil Infrastructure Condition Assessment)
  • Article
  • Open Access
7 Citations
3,325 Views
14 Pages

29 February 2024

In this study, a multiwalled carbon nanotube (MWCNT) dispersion is used as an ink for a single-nozzle inkjet printing system to produce a planar coil that can be used to determine strain wirelessly. The MWCNT dispersion is non-covalently functionaliz...

(This article belongs to the Section Sensor Materials)
  • Article
  • Open Access
15 Citations
4,127 Views
10 Pages

8 January 2020

The conventional magnetoelastic resonant sensor suffers from a low detecting sensitivity problem. In this study, an hourglass-shaped magnetoelastic resonant sensor was proposed, analyzed, fabricated, and tested. The hourglass-shaped magnetoelastic re...

(This article belongs to the Special Issue Magnetoelastic Sensors)
  • Article
  • Open Access
4 Citations
2,526 Views
27 Pages

Reliability Assessment of Wireless Sensor Networks by Strain-Based Region Analysis for Redundancy Estimation in Measurements on the Example of an Aircraft Wing Box

  • Sören Meyer zu Westerhausen,
  • Gurubaran Raveendran,
  • Thorben-Hendrik Lauth,
  • Ole Meyer and ,
  • Daniel Rosemann,
  • Max Leo Wawer,
  • Timo Stauß,
  • Johanna Wurst and
  • Roland Lachmayer
  • + 4 authors+ 0 author

24 June 2024

Wireless sensor networks (WSNs) are attracting increasing research interest due to their ability to monitor large areas independently. Their reliability is a crucial issue, as it is influenced by hardware, data, and energy-related factors such as loa...

(This article belongs to the Section Sensor Networks)
  • Article
  • Open Access
37 Citations
9,579 Views
11 Pages

Quality Factor Effect on the Wireless Range of Microstrip Patch Antenna Strain Sensors

  • Ali Daliri,
  • Amir Galehdar,
  • Wayne S. T. Rowe,
  • Sabu John and ,
  • Chun H. Wang and
  • Kamran Ghorbani
  • + 1 author+ 0 author

2 January 2014

Recently introduced passive wireless strain sensors based on microstrip patch antennas have shown great potential for reliable health and usage monitoring in aerospace and civil industries. However, the wireless interrogation range of these sensors i...

(This article belongs to the Section Physical Sensors)
  • Article
  • Open Access
40 Citations
9,454 Views
22 Pages

Structural Health Monitoring of Fatigue Cracks for Steel Bridges with Wireless Large-Area Strain Sensors

  • Sdiq Anwar Taher,
  • Jian Li,
  • Jong-Hyun Jeong,
  • Simon Laflamme and ,
  • Hongki Jo,
  • Caroline Bennett,
  • William N. Collins and
  • Austin R. J. Downey
  • + 3 authors+ 0 author

6 July 2022

This paper presents a field implementation of the structural health monitoring (SHM) of fatigue cracks for steel bridge structures. Steel bridges experience fatigue cracks under repetitive traffic loading, which pose great threats to their structural...

(This article belongs to the Section Sensor Networks)
  • Abstract
  • Open Access
1,532 Views
3 Pages

A Wireless Strain Sensor for Measurement in Composites

  • Lukas Bertram,
  • Michael Brink and
  • Walter Lang

This paper presents first characterization results of a novel, battery-less sensor for integration into glass fiber-reinforced plastic (FRP) materials. The sensor targets combined usage in both production and structural health monitoring applications...

(This article belongs to the Proceedings of XXXV EUROSENSORS Conference)
  • Article
  • Open Access
27 Citations
7,607 Views
9 Pages

A Passive and Wireless Sensor for Bone Plate Strain Monitoring

  • Yisong Tan,
  • Jiale Hu,
  • Limin Ren,
  • Jianhua Zhu and ,
  • Jiaqi Yang and
  • Di Liu
  • + 1 author+ 0 author

16 November 2017

This paper reports on a sensor for monitoring bone plate strain in real time. The detected bone plate strain could be used for judging the healing state of fractures in patients. The sensor consists of a magnetoelastic material, which can be wireless...

(This article belongs to the Section Physical Sensors)
  • Article
  • Open Access
17 Citations
4,269 Views
21 Pages

Development and Validation of a Framework for Smart Wireless Strain and Acceleration Sensing

  • Omobolaji Lawal,
  • Amirali Najafi,
  • Tu Hoang,
  • Shaik Althaf V. Shajihan and ,
  • Kirill Mechitov and
  • Billie F. Spencer
  • + 1 author+ 0 author

3 March 2022

Civil infrastructure worldwide is subject to factors such as aging and deterioration. Structural health monitoring (SHM) can be used to assess the impact of these processes on structural performance. SHM demands have evolved from routine monitoring t...

(This article belongs to the Section Physical Sensors)
  • Article
  • Open Access
6 Citations
4,187 Views
13 Pages

This article presents a system for monitoring the load caused by strong winds and snow on buildings’ roofs. An estimation of the total load on the structure is obtained by measuring the strain on the main roof girders. The system is based on a...

(This article belongs to the Special Issue Application of Wireless Sensor Networks in Monitoring)
  • Article
  • Open Access
1 Citations
2,353 Views
28 Pages

7 March 2024

Three Pennsylvanian bridges were studied using finite element and wireless sensor technology. A detailed finite element model of each bridge was created using a commercial software in order to calculate the strains generated by a load that simulates...

(This article belongs to the Topic Structural Health Monitoring Based on Materials, Mathematical Methods, and Sensing Technology)
  • Article
  • Open Access
45 Citations
8,566 Views
17 Pages

A Wireless Passive Sensing System for Displacement/Strain Measurement in Reinforced Concrete Members

  • Burak Ozbey,
  • Vakur B. Erturk,
  • Hilmi Volkan Demir,
  • Ayhan Altintas and
  • Ozgur Kurc

8 April 2016

In this study, we show a wireless passive sensing system embedded in a reinforced concrete member successfully being employed for the measurement of relative displacement and strain in a simply supported beam experiment. The system utilizes electroma...

(This article belongs to the Section Physical Sensors)
  • Article
  • Open Access
28 Citations
9,640 Views
17 Pages

Design and Implementation of a Connection between Augmented Reality and Sensors

  • Marlon Aguero,
  • Dilendra Maharjan,
  • Maria del Pilar Rodriguez,
  • David Dennis Lee Mascarenas and
  • Fernando Moreu

Wireless sensor networks (WSN) are used by engineers to record the behavior of structures. The sensors provide data to be used by engineers to make informed choices and prioritize decisions concerning maintenance procedures, required repairs, and pot...

(This article belongs to the Section Sensors and Control in Robotics)
  • Article
  • Open Access
5 Citations
4,854 Views
11 Pages

17 March 2019

Wireless data communication and telemetry during drilling deep oil and gas wells are important enablers for safe and timely drilling operations. The transmission of information through drill strings and pipes using sound waves is a useful and practic...

(This article belongs to the Special Issue Sensing in Oil and Gas Applications)
  • Article
  • Open Access
15 Citations
6,472 Views
18 Pages

Design and Integration of a Wireless Stretchable Multimodal Sensor Network in a Composite Wing

  • Xiyuan Chen,
  • Loic Maxwell,
  • Franklin Li,
  • Amrita Kumar and ,
  • Elliot Ransom,
  • Tanay Topac,
  • Sera Lee,
  • Mohammad Faisal Haider,
  • Sameh Dardona and
  • Fu-Kuo Chang
  • + 5 authors+ 0 author

29 April 2020

This article presents the development of a stretchable sensor network with high signal-to-noise ratio and measurement accuracy for real-time distributed sensing and remote monitoring. The described sensor network was designed as an island-and-serpent...

(This article belongs to the Section Physical Sensors)
  • Article
  • Open Access
11 Citations
4,996 Views
19 Pages

27 November 2020

Due to sensor size and supporting circuitry, in-vivo load and deformation measurements are currently restricted to applications within larger orthopaedic implants. The objective of this study is to repurpose a commercially available low-power, miniat...

(This article belongs to the Section Intelligent Sensors)
  • Article
  • Open Access
6 Citations
4,101 Views
29 Pages

13 July 2023

Fiber reinforced plastics (FRP) offer huge potentials for energy efficient applications. Special care must be taken during both FRP fabrication and usage to ensure intended material properties and behavior. This paper presents a novel approach for th...

(This article belongs to the Section Sensors Development)
  • Article
  • Open Access
16 Citations
9,967 Views
14 Pages

Design and Application of a Field Sensing System for Ground Anchors in Slopes

  • Se Woon Choi,
  • Jihoon Lee,
  • Jong Moon Kim and
  • Hyo Seon Park

18 March 2013

In a ground anchor system, cables or tendons connected to a bearing plate are used for stabilization of slopes. Then, the stability of a slope is dependent on maintaining the tension levels in the cables. So far, no research on a strain-based field s...

(This article belongs to the Section Sensor Networks)
  • Article
  • Open Access
23 Citations
5,492 Views
15 Pages

Development of a Reference-Free Indirect Bridge Displacement Sensing System

  • Jongbin Won,
  • Jong-Woong Park,
  • Junyoung Park,
  • Junsik Shin and
  • Minyong Park

21 August 2021

Bridge displacement measurements are important data for assessing the condition of a bridge. Measuring bridge displacement under moving vehicle loads is helpful for rating the load-carrying capacity and evaluating the structural health of a bridge. D...

  • Article
  • Open Access
7 Citations
4,088 Views
17 Pages

A Low-Cost IoT-Based Bidirectional Torque Measurement System with Strain Gauge Technology

  • Cosmin Constantin Suciu,
  • Virgil Stoica,
  • Mariana Ilie,
  • Ioana Ionel and
  • Raul Ionel

22 July 2025

The scope of this paper is the development of a cost-effective wireless torque measurement system for vehicle drivetrain shafts. The prototype integrates strain gauges, an HX711 conditioner, a Wemos D1 Mini ESP8266, and a rechargeable battery directl...

(This article belongs to the Section Electrical, Electronics and Communications Engineering)
  • Article
  • Open Access
28 Citations
4,320 Views
11 Pages

In this paper, we present the design of an integrated temperature and strain dual-parameter sensor based on surface acoustic waves (SAWs). First, the COMSOL Multiphysics simulation software is used to determine separate frequencies for multiple senso...

(This article belongs to the Topic MEMS Sensors and Resonators)
  • Article
  • Open Access
18 Citations
7,047 Views
13 Pages

19 August 2013

A practical data recovery method is proposed for the strain data lost during the safety monitoring of mega columns. The analytical relations among the measured strains are derived to recover the data lost due to unexpected errors in long-term measure...

(This article belongs to the Section Sensor Networks)
  • Article
  • Open Access
26 Citations
10,794 Views
15 Pages

Determining Wheel Forces and Moments on Aircraft Landing Gear with a Dynamometer Sensor

  • Jaroslaw Pytka,
  • Piotr Budzyński,
  • Tomasz Łyszczyk,
  • Jerzy Józwik and ,
  • Joanna Michałowska,
  • Arkadiusz Tofil,
  • Dariusz Błażejczak and
  • Jan Laskowski
  • + 3 authors+ 0 author

31 December 2019

This paper describes airfield measurement of forces and moments that act on a landing gear wheel. For the measurement, a wheel force sensor was used. The sensor was designed and built based on strain gage technology and was embedded in the left landi...

(This article belongs to the Special Issue Selected papers from the 2019 IEEE International Workshop on Metrology for AeroSpace)
  • Communication
  • Open Access
5 Citations
3,464 Views
9 Pages

Progressive and Asymmetrical Deadlift Loads Captured by Wearable Motion Tape Sensors

  • Elijah Wyckoff,
  • David Sten,
  • Regan Wareham and
  • Kenneth J. Loh

2 December 2024

Weight training is widely adopted and highly effective for enhancing both muscular strength and endurance. A popular weightlifting exercise is the deadlift, which targets multiple muscle groups including the lower back, glutes, and hamstrings. Howeve...

(This article belongs to the Special Issue Wearable Sensors for Optimising Rehabilitation and Sport Training)
  • Article
  • Open Access
6 Citations
2,977 Views
15 Pages

Wireless Strain Gauge for Monitoring Bituminous Pavements

  • Camille Gillot,
  • Benoit Picoux,
  • Philippe Reynaud,
  • Debora Cardoso da Silva and ,
  • Ndrianary Rakotovao-Ravahatra,
  • Noël Feix and
  • Christophe Petit
  • + 2 authors+ 0 author

7 March 2024

This paper introduces the implementation of a new device for measuring deformations at the surface layers of bituminous pavement. Using wireless technology, rechargeable remotely, low cost, and easily positioned in a layer by coring after pavement co...

(This article belongs to the Special Issue Towards the Road of Future—Sustainability and Innovation in Pavement Engineering)
  • Article
  • Open Access
26 Citations
8,536 Views
13 Pages

Wireless Measurement of Elastic and Plastic Deformation by a Metamaterial-Based Sensor

  • Burak Ozbey,
  • Hilmi Volkan Demir,
  • Ozgur Kurc,
  • Vakur B. Erturk and
  • Ayhan Altintas

20 October 2014

We report remote strain and displacement measurement during elastic and plastic deformation using a metamaterial-based wireless and passive sensor. The sensor is made of a comb-like nested split ring resonator (NSRR) probe operating in the near-field...

(This article belongs to the Special Issue Metamaterial-Inspired Sensors)
  • Article
  • Open Access
1 Citations
3,651 Views
13 Pages

Model for Wireless Magnetoelastic Strain Sensors

  • Eduardo S. Bastos,
  • Cristina Bormio-Nunes,
  • Thomas G. R. Clarke and
  • Frank P. Missell

23 June 2020

This paper describes a magnetoelastic strain sensor based on the ∆E effect and discusses some materials used in its construction. A polycrystalline Fe–Al–B alloy with good quality magnetoelastic properties was used as the transducer and g...

(This article belongs to the Special Issue Magnetoelastic Sensors)
  • Article
  • Open Access
41 Citations
19,626 Views
16 Pages

Design and Evaluation of a Wireless Sensor Network Based Aircraft Strength Testing System

  • Jian Wu,
  • Shenfang Yuan,
  • Genyuan Zhou,
  • Sai Ji and ,
  • Zilong Wang and
  • Yang Wang
  • + 1 author+ 0 author

3 June 2009

The verification of aerospace structures, including full-scale fatigue and static test programs, is essential for structure strength design and evaluation. However, the current overall ground strength testing systems employ a large number of wires fo...

(This article belongs to the Special Issue Wireless Sensor Technologies and Applications)
  • Proceeding Paper
  • Open Access
1 Citations
2,076 Views
5 Pages

3D Printing Technique for Passive Wireless Strain Sensing

  • Joshua Dyogi,
  • Xi Song,
  • Sung-Hwan Jang,
  • Sang-Hyeok Nam and
  • Chunhee Cho

Passive wireless sensing systems, particularly passive antenna sensors, offer a viable alternative to traditional wired and active sensors for long-term structural health monitoring due to their simplicity, easy installation and maintenance, and abil...

(This article belongs to the Proceedings of The Second International Conference on Maintenance and Rehabilitation of Constructed Infrastructure Facilities (MAIREINFRA2))
  • Article
  • Open Access
5 Citations
3,979 Views
13 Pages

28 March 2020

A passive wireless impedance-loaded orthogonal frequency-coded (OFC) surface acoustic wave (SAW) sensor for wireless sensor networks was proposed in this paper. One of the chips on OFC SAW tag is connected to an external sensor, which could cause a p...

(This article belongs to the Section Physical Sensors)
  • Article
  • Open Access
44 Citations
10,503 Views
16 Pages

16 December 2013

Sensor technologies have been actively employed in structural health monitoring (SHM) to evaluate structural safety. To provide stable and real-time monitoring, a practical wireless sensor network system (WSNS) based on vibrating wire strain gauges (...

(This article belongs to the Section Sensor Networks)
  • Article
  • Open Access
11 Citations
4,386 Views
28 Pages

Design and Implementation of an IoT-Oriented Strain Smart Sensor with Exploratory Capabilities on Energy Harvesting and Magnetorheological Elastomer Transducers

  • Jorge de-J. Lozoya-Santos,
  • L. C. Félix-Herrán,
  • Juan C. Tudón-Martínez,
  • Adriana Vargas-Martinez and
  • Ricardo A. Ramirez-Mendoza

26 June 2020

This work designed and implemented a new low-cost, Internet of Things-oriented, wireless smart sensor prototype to measure mechanical strain. The research effort explores the use of smart materials as transducers, e.g., a magnetorheological elastomer...

(This article belongs to the Special Issue New Sensors for Nondestructive Evaluation)
  • Article
  • Open Access
8 Citations
3,364 Views
12 Pages

15 March 2022

Wind sensing has become a key component in various fields with the growing trend of assessing air conditions for energy conversion. In this study, we demonstrated a wireless screen-printable flexible strain sensor system based on Ag/MWCNT composite f...

(This article belongs to the Section Nanocomposite Materials)
  • Article
  • Open Access
46 Citations
10,011 Views
19 Pages

15 July 2013

In this study, a practical and integrative SHM system was developed and applied to a large-scale irregular building under construction, where many challenging issues exist. In the proposed sensor network, customized energy-efficient wireless sensing...

(This article belongs to the Section Sensor Networks)
  • Article
  • Open Access
48 Citations
16,355 Views
11 Pages

Implantable Biosensors for Real-time Strain and Pressure Monitoring

  • Ee Lim Tan,
  • Brandon D. Pereles,
  • Brock Horton,
  • Ranyuan Shao and ,
  • Mohammed Zourob and
  • Keat Ghee Ong
  • + 1 author+ 0 author

15 October 2008

Implantable biosensors were developed for real-time monitoring of pressure and strain in the human body. The sensors, which are wireless and passive, consisted of a soft magnetic material and a permanent magnet. When exposed to a low frequency AC mag...

(This article belongs to the Special Issue BioMEMS)
  • Article
  • Open Access
9 Citations
2,483 Views
10 Pages

Contactless Waveguide Characterization of Piezoresistive Materials for Wireless Strain Sensors

  • Sandra Rodini,
  • Simone Genovesi,
  • Giuliano Manara and
  • Filippo Costa

27 May 2022

Stretchable materials are widely used for the realization of various sensors, but their radio frequency behavior has not been fully characterized so far. Here, an innovative method is proposed for deriving the surface impedance of this kind of materi...

(This article belongs to the Section Physical Sensors)
  • Article
  • Open Access
1 Citations
7,052 Views
16 Pages

31 July 2013

As wireless sensor network (WSN)-based structural health monitoring (SHM) systems are increasingly being employed in civil infrastructures and building structures, the management of large numbers of sensing devices and the large amount of data acquir...

(This article belongs to the Section Sensor Networks)
  • Review
  • Open Access
73 Citations
9,663 Views
23 Pages

Review of Wireless RFID Strain Sensing Technology in Structural Health Monitoring

  • Gang Liu,
  • Qi-Ang Wang,
  • Guiyue Jiao,
  • Pengyuan Dang and ,
  • Guohao Nie,
  • Zichen Liu and
  • Junyu Sun
  • + 2 authors+ 0 author

3 August 2023

Strain-based condition evaluation has garnered as a crucial method for the structural health monitoring (SHM) of large-scale engineering structures. The use of traditional wired strain sensors becomes tedious and time-consuming due to their complex w...

(This article belongs to the Section Physical Sensors)
  • Article
  • Open Access
16 Citations
6,812 Views
19 Pages

28 January 2020

Structural health monitoring (SHM) and safety assessment are very important areas for evaluating the behavior of structures. Various wired and wireless sensors can measure the physical responses of structures, such as displacement or strain. One rece...

(This article belongs to the Special Issue Shape Sensing)
  • Article
  • Open Access
16 Citations
8,480 Views
22 Pages

Providing Self-Healing Ability for Wireless Sensor Node by Using Reconfigurable Hardware

  • Shenfang Yuan,
  • Lei Qiu,
  • Shang Gao,
  • Yao Tong and
  • Weiwei Yang

29 October 2012

Wireless sensor networks (WSNs) have received tremendous attention over the past ten years. In engineering applications of WSNs, a number of sensor nodes are usually spread across some specific geographical area. Some of these nodes have to work in h...

(This article belongs to the Section Sensor Networks)
  • Article
  • Open Access
19 Citations
5,609 Views
13 Pages

2 January 2019

A new two-dimensional wireless and passive stress sensor using the inverse magnetostrictive effect is proposed, designed, analyzed, fabricated, and tested in this work. Three pieces of magnetostrictive material are bonded on the surface of a smart el...

(This article belongs to the Special Issue Magnetic Sensors)
  • Article
  • Open Access
14 Citations
5,970 Views
23 Pages

10 November 2022

This paper was concerned with the current level of progress towards the development of chipless radio frequency identification (RFID) sensors that are capable of sensing strain and temperature. More specifically, it was interested in the possibility...

(This article belongs to the Topic Recent Advances in Structural Health Monitoring)
  • Article
  • Open Access
6 Citations
4,622 Views
13 Pages

Practical Evaluation of Printed Strain Sensors Based on Long-Term Static Strain Measurements

  • Daniel Zymelka,
  • Kazuyoshi Togashi,
  • Toshihiro Takeshita,
  • Takahiro Yamashita and
  • Takeshi Kobayashi

14 July 2021

Recent progress in printable electronics has enabled the fabrication of printed strain sensors for diverse applications. These include the monitoring of civil infrastructure, the gradual aging of which raises concerns about its effective maintenance...

(This article belongs to the Section Physical Sensors)
  • Article
  • Open Access
3 Citations
2,343 Views
20 Pages

2 June 2024

Reliable testing of aviation components depends on the quality and configuration flexibility of measurement systems. In a typical approach to test instrumentation, there are tens or hundreds of sensors on the test head and test facility, which are co...

(This article belongs to the Special Issue Feature Papers in Intelligent Sensors 2024)
  • Article
  • Open Access
10 Citations
11,352 Views
14 Pages

29 December 2011

This paper presents the design of a wireless pressure-monitoring system for harsh-environment applications. Two types of ceramic pressure sensors made with a low-temperature cofired ceramic (LTCC) were considered. The first type is a piezoresistive s...

(This article belongs to the Section Physical Sensors)
  • Article
  • Open Access
9 Citations
2,717 Views
15 Pages

Flexible Graphene Film-Based Antenna Sensor for Large Strain Monitoring of Steel Structures

  • Shun Weng,
  • Jingqi Zhang,
  • Ke Gao,
  • Hongping Zhu and
  • Tingjun Peng

6 July 2024

In the field of wireless strain monitoring, it is difficult for the traditional metal-made antenna sensor to conform well with steel structures and monitor large strain deformation. To solve this problem, this study proposes a flexible antenna strain...

(This article belongs to the Section Fault Diagnosis & Sensors)

of 3