- Article
A complete understanding of the solid-state phase equilibria of the ternary Al–Sn–Y system is essential for the development of both Al-based structural materials and Sn-based lead-free solders. In this work, the phase relationships in the...
A complete understanding of the solid-state phase equilibria of the ternary Al–Sn–Y system is essential for the development of both Al-based structural materials and Sn-based lead-free solders. In this work, the phase relationships in the...
TiAl alloys are used in high-temperature components such as the turbine blades of aeroengines because of their excellent properties. However, TiAl alloys are prone to thermal corrosion when in near-ocean service. In order to solve this problem, a hot...
A magnesium alloy containing Al2Y particles was successfully fabricated by changing the content of Al in the Mg-6Y alloy melt. Its microstructure and mechanical properties were subsequently characterized. The results show that two types of Al2Y parti...
The existence mode of Y is an important factor affecting the oxidation resistance of NiCrAlY coating. The traditional thermal sprayed NiCrAlY coating had some problems such as internal-stress-induced coating peeling, when it was used at high temperat...
(Tb0.6Y0.4)3Al5O12 transparent ceramics were successfully fabricated by solid-state reactive sintering using Tb4O7, Y2O3, and α-Al2O3 powders as raw materials. The effect of (Tb+Y)/Al ratio on microstructure evolution and densification process...
Through an activation reaction sintering method, porous (Mo2/3Y1/3)2AlC ceramics were prepared by Mo, Y, Al, and graphite powders as raw materials. The phase composition, microstructure, element distribution, and pore structure characteristics were c...
Grain refinement is of very important significance for improving the microstructure and mechanical properties of Mg alloys. This work investigated how the addition of various amounts of Y element affected the microstructure and mechanical properties...
In this study, the oxidation behavior of Al coated NiCrAlY bondcoat is investigated. It is known that many methods are applied to improve the lifetime of bondcoat in thermal barrier coatings. Herein, the Al sputtering method is selected to increase t...
The main goal of this work was to obtain dense Al2O3–Y3Al5O12 ceramic composites by reactive sintering of three-dimensional samples, built by direct ink writing from a paste containing a mixture of Al2O3 and Y2O3 powders. To obtain a ceramic in...
Two types of coatings, NiCrAlY and NiCrAlY/YSZ, were fabricated on the surface of M247 alloy by the atmospheric plasma spraying (APS) technique. Under pure Na2SO4 and 25 wt.% NaCl-containing mixed salt deposits at 900 °C in air, the M247 alloy un...
MCrAlY (M = Ni and/or Co) metallic coatings are essential for the protection of hot-end components against thermal and corrosion damage. Increasing the Al content is considered a feasible solution to improve the high-temperature performance of MCrAlY...
Thermal shock resistance is a critical parameter for evaluating the long-term service reliability of protective coatings in high-temperature molten-salt environments. In this study, Al2O3–Y2O3 composite coatings containing 0, 2, 5, and 8 wt.% Y...
The phase equilibrium and phase transformation of the Al–Si–Y ternary system were investigated in 80 annealed alloys using an electron probe microanalysis (EPMA), X-ray diffractometry (XRD) and differential scanning calorimetry (DSC). The...
Seven FeCrAlY-Al2O3 nanoceramic composite coatings are deposited on F/M steel via plasma spraying and laser remelting. A systematic investigation is conducted to examine the dependence of microstructure, mechanical properties, and lead–bismuth...
Balancing strength and ductility remains a central challenge in low-alloy Mg–Al–Ca–Mn alloys. In this study, a Mg–12Al2Y master alloy was added to Mg–1.2Al–0.8Ca–0.4Mn to obtain nominal Al2Y contents of 0, 1,...
A TiAlCrSiNbY coating was fabricated on γ-TiAl alloy by arc ion plating. The coating exhibits a dense, crack-free microstructure with a thickness of 5 ± 0.5 μm and strong interfacial bonding with the substrate. The characteristic powe...
The microstructures, phase compositions, and high-temperature oxidation behavior of a NiCrAlY coating fabricated by arc ion plating were investigated by scanning electron microscopy (SEM), energy dispersive spectrometer (EDS), atomic force microscope...
In this study, the metallic Y, CaF2, and sponge Ti were employed to regulate the composition and achieve the deoxidation of the SHS-TiAl alloy, respectively. The results indicate that the metallic Y could effectively reduce the oxygen concentration o...
The degradation process of HVOF-MCrAlY + APS-nanostructured YSZ (APS-nYSZ) thermal barrier coatings, produced using gas turbine OEM-approved MCrAlY powders, is investigated by studying the TGO growth and crack propagation behaviors in a thermal cycli...
High-performance Sc-containing aluminum alloys are limited in their industrial application due to the high cost of Sc elements. Er, Zr, and Y elements are candidates for replacing Sc elements. Combined with the first-principles thermodynamic calculat...
In this work, Y2O3 based composite crucibles with different Al2O3 contents were designed and characterized. The stability behaviors and interaction mechanisms between molten Ti-47Al-2Cr-2Nb alloy and Y2O3-Al2O3 composite crucibles were investigated a...
Metallic coatings based on cobalt and nickel are promising for elongating the life span of machine components operated in harsh environments. However, reports regarding the ambient temperature tribological performance and cavitation erosion resistanc...
To understand the oxidation behaviors of the NiCrAlY bond coats in the thermal barrier coatings (TBCs) under external loads, uniaxial tensile and compressive experiments of the TBCs in air at 900 °C for 100 h were investigated. Then, the experime...
Erosion–corrosion at elevated temperature represents a critical degradation mechanism in components exposed to particle-laden gaseous flows, such as industrial boilers and combustion systems. This study evaluates the combined erosion–corr...
Cermet coatings with ceramic and metal characteristics will play an increasingly important role in extending the service life of critical components in harsh service environments. In this paper, CoCrAlTaY-30Al2O3 (wt.%) cermet coating was prepared by...
To improve the high-temperature oxidation resistance of 20G steel, NiCrAlY and yttria-stabilized zirconia (YSZ) coatings were deposited via plasma spraying. Subsequently, high-temperature cyclic oxidation analysis was performed at 900 °C for a to...
The effect of Y2O3 addition on the microstructure and properties of the laser cladded Al-Si alloy coating on the surface of AZ91D magnesium alloy was investigated in this study. The experimental results showed that the Al-Si + Y2O3 cladding layers co...
AlSi10Mg has a good forming ability and has been widely accepted as an optimal material for selective laser melting (SLM). However, the strength and elongation of unmodified AlSi10Mg are insufficient, which limits its application in the space industr...
In this paper, an Ab-initio study was employed to study the properties of interfaces of Al3Y|Al. The interface strength, shear strength, structural stability, electronic density, bonding characteristics, stacking fault energy, and plasticity were all...
The composition dependence of glass forming ability in the ternary Al-Cu-Y system is predicted by thermodynamic calculations based on the Miedema’s model and Alonso’s method. By comparing the relative energetic status of the amorphous phase versus th...
Bulk cobalt- and nickel-based metallic materials exhibit superior resistance to cavitation erosion and sliding wear. Thus, thermally deposited High-Velocity Oxygen Fuel (HVOF) coatings seem promising for increasing the wear resistance of the bulk met...
Garnet-type rare earth aluminate compounds are one class of promising potential candidate materials for thermal barrier coatings (TBCs). In this paper, (Y0.8Gd0.2)3Al5O12 (GYAG) coatings are fabricated by air plasma spraying, with the microstructure,...
In this work, Y2O3–Al2O3 dielectrics were prepared and used in ZnO thin film transistor as gate insulators. The Y2O3 film prepared by the sol–gel method has many surface defects, resulting in a high density of interface states with the active layer i...
In order to explore the microstructure evolution of an Mg-RE alloy refined by Al during solution treatment, an Mg-3Y-4Nd-2Al alloy was treated at 545 °C for different time periods. Phase evolution of the alloy was investigated. After solution tre...
Since rare earth oxides and hard ceramic particles improve coating quality, a novel Al2O3@Y2O3 core–shell structure was prepared. Then, Ni60A coatings with different amounts (2~6 wt.%) of Al2O3@Y2O3 core–shell structures were prepared usi...
High-performance gas turbines and aircraft engines necessitate MCrAlY (M = Ni, Co, or Ni/Co) coatings with exceptional oxidation resistance. Pre-heat-treatment can enhance the performance of MCrAlY bond coatings in the following ways: First, it reduc...
In the past ten years, many coal mines have encountered the problem of a premature failure of anchor rod materials. Through field investigation and laboratory research, it was found that the premature failure of these bolt materials is mostly caused...
The increasing demand for high-performance aircraft engines has led to a greater emphasis being placed on advanced sealing coating technologies. Developing long-life, self-lubricating, and wear-resistant coatings is of significant research value. Thi...
A Ti6Al4V alloy fabrication via laser powder bed fusion (L-PBF) leads to the formation of coarse columnar β grains that give rise to anisotropic mechanical properties and inadequate strength. Incorporating the rare-earth oxide, yttrium oxide (Y2...
In order to repair a failed AlSiY coating on aeroengine turbine components, the AlSiY coating was stripped using a nitric acid-based removal reagent. The homogeneity of chemical stripping was evaluated and the stripping mechanism was clarified using...
An investigation of MgAl2O4 spinel and Y3Al2O5 (YAG) materials sintered by spark plasma sintering (SPS) was performed. The optical properties of the materials are modified depending on the powder source and the SPS sintering conditions. Spectrophotom...
NiCrAlY coatings were prepared using high-velocity oxygen fuel spraying (HVOF), and the coatings were removed from the substrate to achieve a uniform shape. Vacuum heat treatment (VHT) of the as-sprayed coatings was conducted at different temperature...
NiCrAlY coating was prepared on a stainless steel substrate by an arc ion plating machine and the annealing experiments were carried out at different temperatures using a tube furnace. The effects of annealing temperatures on the morphology, structur...
Herein, sol–gel-processed Y2O3–Al2O3 mixed oxide-based resistive random-access-memory (RRAM) devices with different proportions of the involved Y2O3 and Al2O3 precursors were fabricated on indium tin oxide/glass substrates. The correspond...
Amorphous Al2O3-Y2O3:Er nanolaminate films are fabricated on silicon by atomic layer deposition, and ~1530 nm electroluminescence (EL) is obtained from the metal-oxide-semiconductor light-emitting devices based on these nanofilms. The introduction of...
The article describes the effect of heat treatment on the structural-phase state and properties of a multilayer Cr-Al-Co-Y coating obtained by magnetron sputtering. Heat treatment was carried out at 400, 800 and 1000 °C. The study of the microstr...
The oxidation resistance of the MCrAlY binding coat is due to the formation of protective Al2O3 oxide scale at high temperature. The oxidation behavior of NiCrAlYHf alloy in 1100 °C air and air-water vapor atmosphere was studied. The effect of wa...
Nano-Y2O3 reinforced Ti-47.7Al-7.1Nb-(V, Cr) alloy was fabricated by a powder metallurgy route using spark plasma sintering (SPS), and the influence of nano-Y2O3 contents on the microstructure and mechanical properties were investigated systematicall...
The hot deformation behavior of the duplex structured Mg-9Li-5Al-2Sn-1.5Y alloy is investigated via hot compression tests in the temperature range of 200–350 °C and strain rate range of 0.001–1 s−1. The flow behavior of the Mg-9...
The oxidation and crack propagation behavior of HVOF-NiCrAlY + APS-YSZ thermal barrier coatings in a furnace cycling environment were investigated. It was found that TGO growth yields a power-law relationship,
of 27