Skip to Content

1,050 Results Found

  • Article
  • Open Access
4 Citations
2,255 Views
12 Pages

Investigation of Mold Flux Entrapment in Deep Oscillation Mark of Interstitial-Free Steel Shell Using Mold Simulator

  • Xiong Yan,
  • Wanlin Wang,
  • Lejun Zhou,
  • Xiaocan Zhong and ,
  • Hongliang Lin,
  • Xiaokang Liu,
  • Sibao Zeng and
  • Liwu Zhang
  • + 3 authors+ 0 author

21 March 2024

The slag entrapment defect has become a big issue for the IF steel casting process. In this study, the mechanism of mold flux entrapment in deep oscillation mark of an IF steel shell was studied by a high-temperature mold simulator. Results show that...

(This article belongs to the Section Manufacturing Processes and Systems)
  • Article
  • Open Access
47 Citations
14,413 Views
11 Pages

Enhanced Injection Molding Simulation of Advanced Injection Molds

  • Béla Zink,
  • Ferenc Szabó,
  • István Hatos,
  • András Suplicz and ,
  • Norbert Krisztián Kovács,
  • Hajnalka Hargitai,
  • Tamás Tábi and
  • József Gábor Kovács
  • + 3 authors+ 0 author

22 February 2017

The most time-consuming phase of the injection molding cycle is cooling. Cooling efficiency can be enhanced with the application of conformal cooling systems or high thermal conductivity copper molds. The conformal cooling channels are placed along t...

  • Review
  • Open Access
1,058 Views
23 Pages

16 July 2026

Injection molding is one of the most widely adopted manufacturing methods in the plastics industry, owing to its high efficiency, design flexibility, and mass production capabilities. Throughout the development and application of Injection molding te...

(This article belongs to the Special Issue Emerging Trends and Technologies in Manufacturing Engineering)
  • Article
  • Open Access
23 Citations
6,807 Views
17 Pages

Light-weight structural components are increasingly made of continuous fiber reinforced plastics (CoFRP), but their mass production is still very expensive. Because of its high automation potential, especially the Compression Resin Transfer Molding (...

  • Article
  • Open Access
13 Citations
5,435 Views
36 Pages

1 May 2024

In the plastics industry, CFD simulation has been used for many years to support mold design. However, using simulation as a substitute for experimentation remains a major challenge to this day. This is due to the unknown congruence between simulatio...

(This article belongs to the Section Polymer Processing and Engineering)
  • Article
  • Open Access
15 Citations
5,138 Views
28 Pages

Modeling and Simulation of the Casting Process with Skeletal Sand Mold

  • Jinwu Kang,
  • Jiwu Wang,
  • Haolong Shangguan,
  • Lele Zheng and ,
  • Chengyang Deng,
  • Yongyi Hu and
  • Jihao Yi
  • + 2 authors+ 0 author

31 March 2020

The author-proposed skeletal sand mold, which mainly includes a shell, air cavities and a truss support structure, has been experimentally proven to be very useful in controlling the cooling of casting at local areas and at different periods of the c...

  • Review
  • Open Access
11 Citations
6,967 Views
26 Pages

Multiscale Modeling and Simulation of Polymer Blends in Injection Molding: A Review

  • Lin Deng,
  • Suo Fan,
  • Yun Zhang,
  • Zhigao Huang and ,
  • Huamin Zhou,
  • Shaofei Jiang and
  • Jiquan Li
  • + 2 authors+ 0 author

31 October 2021

Modeling and simulation of the morphology evolution of immiscible polymer blends during injection molding is crucial for predicting and tailoring the products’ performance. This paper reviews the state-of-the-art progress in the multiscale modeling a...

(This article belongs to the Special Issue Advanced Polymer Simulation and Processing)
  • Article
  • Open Access
24 Citations
8,326 Views
16 Pages

Simulation of Reinforced Reactive Injection Molding with the Finite Volume Method

  • Florian Wittemann,
  • Robert Maertens,
  • Alexander Bernath,
  • Martin Hohberg and ,
  • Luise Kärger and
  • Frank Henning
  • + 1 author+ 0 author

The reactive process of reinforced thermoset injection molding significantly influences the mechanical properties of the final composite structure. Therefore, reliable process simulation is crucial to predict the process behavior and relevant process...

(This article belongs to the Special Issue Discontinuous Fiber Composites)
  • Article
  • Open Access
1 Citations
2,445 Views
18 Pages

Research on the End-Face Distribution of Rotational Molding Heating Gun Based on Numerical Simulation Method

  • Yongchun Yan,
  • Lixin Zhang,
  • Xiao Ma,
  • Huan Wang and ,
  • Wendong Wang and
  • Yan Zhang
  • + 1 author+ 0 author

4 January 2022

The distribution of heating gun ends plays a decisive role in the sidewall properties of finished rotomolded products. To obtain the optimal distribution of the end face of a rotational molding heating gun, the temperature response of the end-face mo...

(This article belongs to the Special Issue Industrial Applications of Modeling Tools)
  • Article
  • Open Access
19 Citations
4,407 Views
14 Pages

Injection Molding Process Simulation of Polycaprolactone Sticks for Further 3D Printing of Medical Implants

  • Krzysztof Formas,
  • Anna Kurowska,
  • Jarosław Janusz,
  • Piotr Szczygieł and
  • Izabella Rajzer

18 October 2022

The aim of the present study was a simulation of the injection molding process of polycaprolactone filament sticks for further 3D printing of osteochondral implants. Polycaprolactone data are not available in the data banks of popular injection moldi...

(This article belongs to the Topic Material and Process Innovations for 3D Printing Applications)
  • Article
  • Open Access
33 Citations
12,739 Views
50 Pages

31 October 2020

Discontinuous fiber composites (DFC) such as carbon fiber sheet molding compounds (CF-SMC) are increasingly used in the automotive industry for manufacturing lightweight parts. Due to the flow conditions during compression molding of complex geometr...

(This article belongs to the Special Issue Discontinuous Fiber Composites, Volume II)
  • Review
  • Open Access
45 Citations
9,807 Views
28 Pages

25 October 2023

Injection molding is a multiphase process that requires accurate simulation of the filling phase. This is a key element in predicting the complete injection molding cycle. The filling phase presents a complex set of challenges, including migrating me...

  • Article
  • Open Access
11 Citations
3,884 Views
15 Pages

28 April 2023

The simulation solutions of different plastic injection molding processes are as multifaceted as the field of injection molding itself. In this study, the simulation of a special injection molding process, which generates partially foamed integral co...

(This article belongs to the Special Issue Research on Polymer Simulation, Modeling and Computation)
  • Article
  • Open Access
20 Citations
8,032 Views
30 Pages

Experimental and Numerical Analysis of SMC Compression Molding in Confined Regions—A Comparison of Simulation Approaches

  • Florian Rothenhäusler,
  • Nils Meyer,
  • Simon Wehler,
  • Martin Hohberg and ,
  • Maik Gude,
  • Frank Henning and
  • Luise Kärger
  • + 2 authors+ 0 author

23 February 2022

The compression molding process of sheet molding compound (SMC) is an economical manufacturing process for lightweight parts. However, molding defects, such as fiber matrix separation, and fiber re-orientation, may develop during the molding process...

(This article belongs to the Special Issue Discontinuous Fiber Composites, Volume III)
  • Article
  • Open Access
5 Citations
2,655 Views
20 Pages

Investigation of a Non-Equilibrium Energy Model for Resin Transfer Molding Simulations

  • Anthony Sherratt,
  • Anthony G. Straatman,
  • Christopher T. DeGroot and
  • Frank Henning

Due to the high design freedom and weight specific properties carbon fiber reinforced plastics (CFRP) offer significant potential in light-weighting applications, specifically in the automotive sector. The demand for medium to high production quantit...

(This article belongs to the Special Issue Characterization and Modelling of Composites, Volume II)
  • Article
  • Open Access
10 Citations
3,457 Views
13 Pages

23 February 2021

Slag entrapment is a critical problem that affects the quality of steel. In this work, a three-dimensional model is established to simulate the slag entrapment phenomenon, mainly focusing on the slag entrapment phenomenon at the interface between sla...

(This article belongs to the Section Metal Casting, Forming and Heat Treatment)
  • Article
  • Open Access
18 Citations
5,738 Views
13 Pages

19 April 2020

A special mold provided with a glass window was used in order to directly evaluate the flow progression during the filling phase of the injection molding process in a thin-wall cavity and to validate the simulation of the process with particular focu...

(This article belongs to the Special Issue 10th Anniversary of Micromachines)
  • Article
  • Open Access
1,565 Views
19 Pages

Injection Molding Simulation of Polycaprolactone-Based Carbon Nanotube Nanocomposites for Biomedical Implant Manufacturing

  • Krzysztof Formas,
  • Jarosław Janusz,
  • Anna Kurowska,
  • Aleksandra Benko and ,
  • Wojciech Piekarczyk and
  • Izabella Rajzer
  • + 1 author+ 0 author

6 July 2025

This study consisted of the injection molding simulation of polycaprolactone (PCL)-based nanocomposites reinforced with multi-walled carbon nanotubes (MWCNTs) for biomedical implant manufacturing. The simulation was additionally supported by experime...

(This article belongs to the Section Biomaterials)
  • Article
  • Open Access
27 Citations
6,456 Views
18 Pages

Numerical Simulation and Experimental Validation of Hybrid Injection Molded Short and Continuous Fiber-Reinforced Thermoplastic Composites

  • Patrick Hirsch,
  • Marianne John,
  • Daniel Leipold,
  • André Henkel and ,
  • Sylvia Gipser,
  • Ralf Schlimper and
  • Matthias Zscheyge
  • + 2 authors+ 0 author

7 November 2021

In-situ thermoforming and overmolding of continuous fiber-reinforced thermoplastic composites by hybrid injection molding enables the mass production of thermoplastic lightweight structures with a complex geometry. In this study, the anisotropic mech...

(This article belongs to the Special Issue Advanced Polymer Simulation and Processing)
  • Article
  • Open Access
30 Citations
5,428 Views
32 Pages

30 April 2022

In this study, we determined the effects of design and processing parameters of precision injection molding (PIM) to minimize warpage phenomena of micro-sized parts using various plastics (polyoxymethylene (POM), acrylonitrile-butadiene-styrene (ABS)...

(This article belongs to the Special Issue Injection Molding of Polymers)
  • Review
  • Open Access
2 Citations
3,395 Views
15 Pages

4 August 2022

This paper adopted transient CFD (Computational Fluid Dynamics) simulation analysis with an experimental method for designing and surveying the quick and uniform rise in the temperature of the plastics into the insert mold cavity. Plastic injection m...

  • Article
  • Open Access
2 Citations
2,917 Views
19 Pages

8 March 2025

While design groups have utilized the abilities of injection molding simulation software, its use is often underutilized by process engineers. To expand the application of simulation software to manufacturing groups, this work focuses on developing a...

(This article belongs to the Special Issue Applications of Process Simulation in Polymer-Based Products Injection Molding)
  • Article
  • Open Access
21 Citations
5,589 Views
24 Pages

20 September 2024

This contribution provides a detailed comparison of the impact of various rheological models on the filling phase of injection molding simulations in order to enhance the accuracy of flow predictions and improve material processing. The challenge of...

  • Article
  • Open Access
5 Citations
2,046 Views
18 Pages

28 June 2023

In this paper, a fully coupled large eddy simulation model, including the volume of fluid model, the discrete phase model, the bubble-collision model, and the bubble-breakup model was used to simulate the spatial distribution of multi-size bubbles an...

(This article belongs to the Special Issue Metallurgical Process Simulation and Optimization—2nd Volume)
  • Article
  • Open Access
31 Citations
6,789 Views
27 Pages

22 December 2021

During injection molding of short glass fiber reinforced composites, a complex structure is formed due to the fiber movement. The resulting fiber orientation can be predicted using various simulation models. However, the models are known to have inad...

(This article belongs to the Special Issue Fiber-Reinforced Polymer-Based Composites: Processing, Characterization and Performance)
  • Article
  • Open Access
5 Citations
2,029 Views
19 Pages

5 April 2025

To address the challenges of unclear thermo-mechanical coupling mechanisms and unpredictable multi-field synergistic effects in segmented tire molds during vulcanization, this study focuses on segmented tire molds and proposes a multi-physics couplin...

  • Article
  • Open Access
11 Citations
3,532 Views
18 Pages

23 November 2021

In the present work, the flow field in a slab continuous casting mold with thicknesses of 180 and 250 mm are compared using high temperature quantitative measurement and numerical simulation. The results of the numerical simulation are in agreement w...

(This article belongs to the Special Issue Advances in the Continuous Casting of Steel)
  • Article
  • Open Access
440 Views
12 Pages

Research on Quenching of 65Mn Friction Plates in Internal-Circulation Water Channel Molds Based on Finite Element Simulation

  • Yu Wang,
  • Ziheng Zhao,
  • Jingang Liu,
  • Xiaoxuan Tu and ,
  • Gaifen Lu,
  • Jianwen Chen and
  • Ke Liu
  • + 2 authors+ 0 author

4 June 2026

To address uneven surface hardness distribution in 65Mn external tooth friction plates after furnace quenching and disc mold tempering, we adopted an integrated quenching and forming process, using an internal-circulation mold. By simultaneously impl...

(This article belongs to the Section Materials Simulation and Design)
  • Article
  • Open Access
12 Citations
2,911 Views
12 Pages

16 June 2023

A numerical analysis of the influence of race tracking on dry spots formation and the accuracy of permeability measurement during the resin-transfer-molding process is presented. In the numerical simulation of the mold-filling process, defects are ra...

(This article belongs to the Section Manufacturing Processes and Systems)
  • Article
  • Open Access
18 Citations
4,875 Views
14 Pages

17 June 2020

Injection molding is an economical and effective method for manufacturing polymer parts with nanostructures and residual stress in the parts is an important factor affecting the quality of molding. In this paper, taking the injection molding of polym...

  • Article
  • Open Access
15 Citations
4,136 Views
23 Pages

A Simulation and Optimization Study of the Swirling Nozzle for Eccentric Flow Fields of Round Molds

  • Peng Lin,
  • Yan Jin,
  • Fu Yang,
  • Ziyu Liu and ,
  • Rundong Jing,
  • Yang Cao,
  • Yuyang Xiang,
  • Changgui Cheng and
  • Yang Li
  • + 4 authors+ 0 author

25 May 2020

In continuous casting, the nozzle position may deviate from the center under actual operating conditions, which may cause periodic fluctuation of the steel-slag interface and easily lead to slag entrapment and gas absorption. Swirling nozzles can red...

  • Feature Paper
  • Article
  • Open Access
32 Citations
6,283 Views
17 Pages

Experimental Validation of Injection Molding Simulations of 3D Microparts and Microstructured Components Using Virtual Design of Experiments and Multi-Scale Modeling

  • Dario Loaldi,
  • Francesco Regi,
  • Federico Baruffi,
  • Matteo Calaon and ,
  • Danilo Quagliotti,
  • Yang Zhang and
  • Guido Tosello
  • + 2 authors+ 0 author

24 June 2020

The increasing demand for micro-injection molding process technology and the corresponding micro-molded products have materialized in the need for models and simulation capabilities for the establishment of a digital twin of the manufacturing process...

(This article belongs to the Special Issue Latest Advancements in Micro Nano Molding Technologies – Process Developments and Optimization, Materials, Applications, Key Enabling Technologies)
  • Article
  • Open Access
5 Citations
3,433 Views
14 Pages

17 November 2024

This technical paper delves into the creation and application of an enhanced mathematical model for semi crystalline thermoplastics based on the Pressure-Volume-Temperature (PVT) Two Domain Tait Equation. The model is designed to incorporate the impa...

(This article belongs to the Section Polymer Processing and Engineering)
  • Article
  • Open Access
23 Citations
5,405 Views
12 Pages

28 December 2017

Compression molding of long fiber reinforced composites offers specific advantages in automotive applications due to the high strength to weight ratio, the comparably low tooling costs and short cycle times. However, the manufacturing process of long...

(This article belongs to the Special Issue Discontinuous Fiber Composites)
  • Article
  • Open Access
8 Citations
3,603 Views
18 Pages

14 October 2022

In this article, a multiscale simulation method of polymer melt injection molding filling flow is established by combining an improved smoothed particle hydrodynamics method and clustered fixed slip-link model. The proposed method is first applied to...

(This article belongs to the Special Issue Advances in Polymer Processing and Molding)
  • Article
  • Open Access
6 Citations
3,698 Views
13 Pages

Integrated Numerical Simulations and Experimental Measurements for the Sintering Process of Injection-Molded Ti-6Al-4V Alloy

  • Shaohua Su,
  • Zijian Hong,
  • Yuhui Huang,
  • Peng Wang and ,
  • Xiaobao Li,
  • Junwen Wu and
  • Yongjun Wu
  • + 2 authors+ 0 author

16 November 2022

Metal injection molding (MIM) is an advanced manufacturing technology that enables the mass production of high-performance and complex materials, such as the Ti-6Al-4V alloy. The determination of the size change and deformation of the Ti-6Al-4V alloy...

(This article belongs to the Special Issue Advances in Sheet Metal Forming Processes of Lightweight Alloys)
  • Article
  • Open Access
13 Citations
5,705 Views
12 Pages

26 January 2021

Injection molding of rubber compounds is an easily conducted yet sophisticated method for rubber processing. Simulation software is used to examine the optimal process conditions, identify failure scenarios, and save resources. Due to the complexity...

(This article belongs to the Section Polymer Processing and Engineering)
  • Article
  • Open Access
47 Citations
4,817 Views
13 Pages

Large Eddy Simulation of Multi-Phase Flow and Slag Entrapment in a Continuous Casting Mold

  • Xianglong Li,
  • Baokuan Li,
  • Zhongqiu Liu,
  • Ran Niu and ,
  • Yanqiang Liu,
  • Changliang Zhao,
  • Caide Huang,
  • Huanshan Qiao and
  • Tianxiang Yuan
  • + 4 authors+ 0 author

21 December 2018

A transient, three-dimensional mathematical model has been developed to study the slag entrapment in a continuous casting mold. The unsteady turbulent flow is computed using the large eddy simulation (LES). The sub-grid scale structure is modeled by...

  • Article
  • Open Access
13 Citations
3,994 Views
13 Pages

23 September 2019

Injection molding is one of the most potential techniques for fabricating polymeric products in large numbers. The filling process, but also the demolding process, influence the quality of injection-molded nanostructures. In this study, nano-cavities...

(This article belongs to the Special Issue Latest Advancements in Micro Nano Molding Technologies – Process Developments and Optimization, Materials, Applications, Key Enabling Technologies)
  • Article
  • Open Access
2 Citations
1,879 Views
15 Pages

12 September 2025

In this research, the thermal and structural responses of high-performance dielectric strength polymers in the injection molding process for multi-pin electrical connectors were thoroughly studied using Moldflow simulations and optimized via a Box&nd...

(This article belongs to the Special Issue Applications of Process Simulation in Polymer-Based Products Injection Molding)
  • Article
  • Open Access
12 Citations
3,153 Views
24 Pages

Simulation of Inclusion Particle Motion Behavior under Interfacial Tension in Continuous Casting Mold

  • Md Irfanul Haque Siddiqui,
  • Ayidh Albaqami,
  • Latif Arifudin,
  • Khalid Alluhydan and
  • Ibrahim Abdullah Alnaser

24 October 2022

Inclusions entrapped by the solidifying front during continuous casting adversely affect the properties of the final steel products. In this study, we investigated the effect of the interfacial tension due to surfactant concentration, particularly su...

(This article belongs to the Special Issue Metallurgical Process Simulation and Optimization)
  • Article
  • Open Access
3 Citations
3,045 Views
20 Pages

17 July 2024

Selecting the optimal settings for the production of rubber goods can be a very time-consuming and resource-intensive process. A promising method for optimizing rubber processing in a short period of time is the use of simulation routines. However, p...

(This article belongs to the Section Polymer Processing and Engineering)
  • Article
  • Open Access
3 Citations
2,947 Views
14 Pages

14 July 2021

Due to the adhesion between the polymer melt and nickel (Ni) mold insert in the micro injection molding process, deformation defects frequently occur when the microstructures are demolded from the insert. In this study, self-assembled alkanethiols we...

(This article belongs to the Special Issue Advances in Computational Materials Science on Functional Interfaces and Surfaces)
  • Feature Paper
  • Article
  • Open Access
15 Citations
6,341 Views
12 Pages

6 October 2017

A debinding step using the supercritical state of a fluid has been increasingly investigated for extracting organic binders from components obtained by metal-injection molding. It consists of placing the component in an enclosure subjected to pressur...

(This article belongs to the Section Materials Science and Engineering)
  • Article
  • Open Access
10 Citations
3,805 Views
14 Pages

Engineering Additive Manufacturing and Molding Techniques to Create Lifelike Willis’ Circle Simulators with Aneurysms for Training Neurosurgeons

  • Pin-Chuan Chen,
  • Jang-Chun Lin,
  • Chung-Hsuan Chiang,
  • Yi-Chin Chen and ,
  • Jia-En Chen and
  • Wei-Hsiu Liu
  • + 1 author+ 0 author

3 December 2020

Neurosurgeons require considerable expertise and practical experience in dealing with the critical situations commonly encountered during difficult surgeries; however, neurosurgical trainees seldom have the opportunity to develop these skills in the...

(This article belongs to the Special Issue Polymer Micro/Nanofabrication and Manufacturing)
  • Article
  • Open Access
2 Citations
576 Views
38 Pages

17 June 2026

This contribution presents a simulation-based approach for optimizing injection molding processes using digital twins. It combines surrogate modeling via response surface methodology (RSM) with the evolutionary algorithm NSGA-II to efficiently captur...

(This article belongs to the Section Applied Industrial Technologies)
  • Feature Paper
  • Article
  • Open Access
3,122 Views
18 Pages

10 September 2023

The present work aims to explore the ability to simulate flow patterns and the velocity field in the powder injection molding (PIM) process using the smoothed particle hydrodynamics (SPH) method. Numerical simulations were performed using the DualSPH...

(This article belongs to the Section Powder Metallurgy)
  • Article
  • Open Access
37 Citations
6,485 Views
15 Pages

2 June 2020

Hybrid fiber reinforced thermoplastic composites are receiving important attention in lightweight applications. The fabrication process of hybrid thermoplastic composites is that discontinuous fiber reinforced thermoplastics are injected onto the con...

(This article belongs to the Section Polymer Processing and Engineering)
  • Article
  • Open Access
48 Citations
8,154 Views
12 Pages

17 May 2016

Ultrasonic plasticizing of polymers for micro-injection molding has been proposed and studied for its unique potential in materials and energy-saving. In our previous work, we have demonstrated the characteristics of the interfacial friction heating...

(This article belongs to the Special Issue Computational Modeling and Simulation in Polymer)
  • Article
  • Open Access
1 Citations
2,396 Views
18 Pages

Finite Element Simulation Tests of the Structural Strength of the Molding Module for Burger Production from Vegetable Outgrades

  • Łukasz Ignasiak,
  • Agata Bieńczak,
  • Paweł Woźniak,
  • Katarzyna Kozłowicz and ,
  • Renata Różyło and
  • Jan Szczepaniak
  • + 1 author+ 0 author

9 November 2021

The aim of the study was to assess the stresses of the structural materials of the forming module in the process of burger production from vegetable outgrades. The simulation research object was a virtual CAD 3D model of a device used for forming mul...

of 21