This paper presents a study and comparison of surface effects induced by picosecond and nanosecond laser modification of a Ti6Al4V alloy surface under different ambient conditions: air and argon- and nitrogen-rich atmospheres. Detailed surface charac...
In this experimental study, picosecond laser treatment was performed on a nickel-based superalloy Nimonic 263, aiming to investigate the surface effects induced by irradiation in different atmospheric conditions and, concerning changes in surface com...
Chlorella vulgaris is a green microalga with a high chlorophyll content, representing a valuable source of green pigments for food applications. As the application of whole biomass can promote an unpleasant fish-like flavor, the use of chlorophyll ex...
The detrimental effect of nitrogen and oxygen when it comes to the precipitation of the strengthening γ’’ and γ’ phases in Alloy 718 is well-known from traditional manufacturing. Hence, the influence of the two processing atmospheres, namely argon an...
In order to obtain the chemical reaction mechanism of Al-rich Al/PTFE/TiH2 composites in argon and oxygen atmosphere, Al/PTFE, PTFE/TiH2, Al/TiH2 and Al-rich Al/PTFE/TiH2 with different contents of TiH2 composites were prepared by using the wet mixin...
Electrification represents a fundamental process in planetary atmospheres, widespread in the Solar System. The atmospheres of the terrestrial planets (Venus, Earth, and Mars) range from thin to thick are rich in heavier gases and gaseous compounds, s...
Copper (Cu), silver (Ag), and copper–silver (Cu–Ag) powders were synthesized using ultrasonic spray pyrolysis (USP) combined with hydrogen-assisted reduction in order to examine how key processing parameters influence particle characteris...
A complex concentrated noble alloy (CCNA) of equiatomic composition (Ag20Pd20Pt20Cu20Ni20–20 at. %) was studied as a potential high—performance material. The equiatomic composition was used so that this alloy could be classified in the su...
This paper presents the results of structural tests and hardness measurements of rebuilding coatings manually applied by the gas tungsten arc welding (GTAW) method on damaged surfaces of steel shafts of turbochargers of automotive engines. Single- an...
This paper describes the combination of surface engineering and powder metallurgy to create a coating with improved corrosion resistance and wear properties. A new method has been developed to manufacture corrosion-resistant surface layers on steel s...
The Silres H62C methyl-phenyl-vinyl-hydrogen polysiloxane is a promising candidate as a SiC precursor for 3D printing based on photopolymerization reaction. An in-depth nuclear magnetic resonance spectroscopy analysis allowed us to determine its stru...
Diamond-like carbon (DLC) film has gained widespread popularity as a versatile and important solid lubricant material in the field of tribology. Among various types of DLC films, hydrogen-rich DLC (a-C:H) film as a high-performance material has great...
The initial atmospheric corrosion of ZM (ZnAlMg)-coated steel in humid air (85% RH) and humid argon (85% RH) containing 320 ppb SO2 was studied using in situ infrared reflection absorption spectroscopy (IRRAS), FTIR-ATR focal plane array (FPA) imagin...
This article reports on the structure and electronic properties of carbon-rich polysilazane polymer-derived silicon carbonitride (C/SiCN) corresponding to pyrolysis temperatures between 1100 and 1600 °C in an argon atmosphere. Raman spectroscopy,...
Active screen plasma nitriding (ASPN) of additively manufactured nickel-based superalloys represents an understudied surface enhancement pathway. This study presents the first systematic investigation of ASPN applied to additively manufactured Incone...
Mg–Si thin films (23 ≤ at.% Si ≤ 43) were deposited by co-sputtering of Mg and Si targets in an argon atmosphere. Two groups of samples were prepared with respect to sputtering parameters. The first Group I was synthesized while residual...
This paper demonstrates the enhanced NO2 sensing performance of graphene with defects generated by rapid thermal annealing (RTA). A high temperature of RTA (300–700 °C) was applied to graphene under an argon atmosphere to form defects on sp2 carbon l...
Thermoelectrics is one promising way of increasing the efficiency of machines and devices by reusing some of the waste heat produced. One obstacle for commercialization is the need to coat the materials to prevent sublimation and oxidation of the the...
Noble gases have become a powerful tool to constrain the origin and evolution of ore-forming fluids in seafloor hydrothermal systems. The aim of this study was to apply these tracers to understand the genesis of newly discovered polymetallic sulphide...
The present study developed a novel approach for transforming red mud (RM) into soft magnetic materials (SMMs) for applications in advanced electrical devices in the form of Fe-Si and Fe-Si-Al alloys. A total of ten blends were prepared based on two...
The W/Cu binary system is characterized by its mutual insolubility and excellent wettability, making W/Cu composite materials ideal for managing thermal and electrical properties in electronic components. To optimize material properties, control over...
The Daliuhang gold deposit in the Qipengfu (Qixia–Penglai–Fushan) ore concentration area is a typical gold deposit of medium-low temperature hydrothermal veins. Uncertainties regarding the primary sources of ore-forming fluids, as well as...
The Yushui ore deposit, located in the middle section of the Yong’an-Meixian Hercynian depression, is a medium-sized Cu-polymetallic massive sulphide deposit in Eastern Guangdong Province, South China. This deposit is characterized by unusually...
AlSi10Mg has been one of the most studied and employed aluminum alloys for additive manufacturing via laser powder-bed fusion (L-PBF). The optimization of manufacturing parameters is important for reducing internal defects, including porosity and ina...