Skip to Content

1,477 Results Found

  • Article
  • Open Access
24 Citations
5,459 Views
15 Pages

10 June 2019

This work mainly focuses on a series of microstructural analysis and predictions regarding dynamic recrystallization behavior, change in grain size, and dislocation density. Additionally, this study includes the shape prediction of the stir zone form...

(This article belongs to the Special Issue The Behaviours of Alloys under Thermo-Mechanical Treatment)
  • Article
  • Open Access
2 Citations
2,755 Views
17 Pages

Microstructure and Texture Evolution of Hot-Rolled Mg-3Gd Alloy during Recrystallization

  • Fang Han,
  • Hanxi Wang,
  • Xuan Luo,
  • Ziyong Hou and ,
  • Guilin Wu and
  • Xiaoxu Huang
  • + 1 author+ 0 author

30 June 2023

An Mg-3Gd (wt.%) sample with gradient rolling strains (ε = 0–0.55) was prepared using a wedge-shaped plate after one-pass hot rolling, allowing a high-throughput characterization of microstructure and texture over a wide strain range within one hot-r...

(This article belongs to the Special Issue Microstructure Evolution and Mechanical Properties of Magnesium Alloys—2nd Edition)
  • Article
  • Open Access
2 Citations
1,634 Views
10 Pages

The Recrystallized Microstructures and Mechanical Properties of a Hypo-Eutectic Al13Ni36Cr10Fe40Mo1 High-Entropy Alloy

  • Hui Li,
  • Han Wang,
  • Xiaoyu Bai,
  • Peng Yan and ,
  • Linxiang Liu,
  • Chuwen Wang,
  • Yunji Qiu and
  • Zhijun Wang
  • + 3 authors+ 0 author

23 May 2025

Recrystallization is a critical process for tailoring the microstructure to enhance the mechanical properties of alloys. In duplex-phase alloys, the recrystallization is different due to the influence of the second phase. Hypo-eutectic high-entropy a...

(This article belongs to the Special Issue Characterization of Metallic Materials: Solidification, Deformation, Heat Treatment and Other Related Phenomena—Third Edition)
  • Article
  • Open Access
6 Citations
3,384 Views
12 Pages

1 June 2023

A novel annealing process of controlled heating rate is used to produce severe cold-formed aluminum plates, which are processed into aluminum foil and mainly used for high-voltage electrolytic capacitor anodes. The experiment in this study focused on...

(This article belongs to the Special Issue Processing–Microstructure–Properties Loop in Materials and Metallurgical Engineering)
  • Article
  • Open Access
6 Citations
2,705 Views
14 Pages

Microstructure, Hot Deformation Behavior, and Recrystallization Behavior of Zn-1Fe-1Mg Alloy under Isothermal Compression

  • Penghao Xue,
  • Minglong Ma,
  • Yongjun Li,
  • Xinggang Li and ,
  • Jiawei Yuan,
  • Guoliang Shi,
  • Kaikun Wang and
  • Kui Zhang
  • + 3 authors+ 0 author

1 April 2021

Nowadays, wrought zinc-based biodegradable alloys are favored by researchers, due to their excellent mechanical properties and suitable degradation rates. However, there are few research studies on their thermal deformation behavior at present. This...

(This article belongs to the Section Biomaterials)
  • Article
  • Open Access
27 Citations
4,956 Views
17 Pages

7 January 2019

Controlling the microstructure homogeneity is crucial in achieving high quality tantalum (Ta) sputtering targets used in integrated circuit fabrication. Unluckily, traditional rolling easily generates a microstructure gradient along the thickness dir...

  • Article
  • Open Access
738 Views
15 Pages

Static Recrystallization Behavior and Microstructure Evolution of SA-508M Gr.3 Steel

  • Chuang Mao,
  • Mingze Liu,
  • Lanjun Ren,
  • Xinrui Wang and ,
  • Lei Sun,
  • Jinhao Liu,
  • Hongyu Yi,
  • Dapeng Gu and
  • Xingang Liu
  • + 4 authors+ 0 author

25 June 2026

In this study, double-pass hot compression tests were conducted to systematically investigate the effects of hot deformation parameters on the static recrystallization (SRX) behavior of SA-508M Gr.3 steel used for nuclear reactor pressure vessels. Th...

(This article belongs to the Section Metal Casting, Forming and Heat Treatment)
  • Article
  • Open Access
2 Citations
2,623 Views
22 Pages

Modeling and Simulation of Dynamic Recrystallization Microstructure Evolution for GCr15 Steel Using the Level Set Method

  • Xuewen Chen,
  • Mingyang Liu,
  • Yisi Yang,
  • Yahui Si and ,
  • Zheng Zhou,
  • Xudong Zhou and
  • Dongwon Jung
  • + 2 authors+ 0 author

14 January 2025

The microstructure of metallic materials plays a crucial role in determining their performance. In order to accurately predict the dynamic recrystallization (DRX) behavior and microstructural evolution during the hot deformation process of GCr15 bear...

(This article belongs to the Special Issue Progressive Technologies and Materials in Mechanical and Materials Engineering)
  • Article
  • Open Access
8 Citations
2,332 Views
16 Pages

28 May 2024

Friction stir processing (FSP), a severe plastic deformation process, was applied on commercially pure Ti to obtain an improved microstructure. The process yielded a refined microstructure and higher mechanical properties at room temperature (RT). Ye...

  • Article
  • Open Access
2 Citations
3,300 Views
13 Pages

Effect of Extensive and Limited Plastic Deformation on Recrystallized Microstructure of Oxide Dispersion Strengthened Fe-Cr-Al Alloy

  • Carlos Capdevila,
  • Rosalia Rementeria,
  • Maria M. Aranda,
  • Javier Vivas and ,
  • Jesus Chao and
  • Vicente Amigó
  • + 1 author+ 0 author

11 December 2018

Ferritic oxide dispersion-strengthened alloys (ODS) are manufactured using a mechanical alloying process. The development of a coarse-grained microstructure during recrystallization has been detected and discussed by several authors, but the mechanis...

  • Article
  • Open Access
16 Citations
3,793 Views
15 Pages

Simulation of Dynamic and Meta-Dynamic Recrystallization Behavior of Forged Alloy 718 Parts Using a Multi-Class Grain Size Model

  • Christian Gruber,
  • Peter Raninger,
  • Aleksandar Stanojevic,
  • Flora Godor and ,
  • Markus Rath,
  • Ernst Kozeschnik and
  • Martin Stockinger
  • + 2 authors+ 0 author

29 December 2020

Dynamic and meta-dynamic recrystallization occur during forging of alloy 718 aircraft parts and thus change the microstructure during a multistep production route. Since the prediction of the resulting grain structure in a single grain fraction is no...

(This article belongs to the Special Issue Forging Processes of Materials)
  • Article
  • Open Access
1 Citations
968 Views
16 Pages

Study on the Recrystallization Behavior and Texture Evolution of 0.5 mm Electromagnetic Pure Iron Cold-Rolled Strip

  • Qing Li,
  • Huaying Li,
  • Yinghui Wei,
  • Yipu Shi and ,
  • Baosheng Liu and
  • Yong Jiang
  • + 1 author+ 0 author

19 December 2025

The control of recrystallization in submillimeter-gauge electromagnetic pure iron strips is critical for developing high-sensitivity electromagnetic devices, yet the microstructure–property relationship during annealing remains poorly understoo...

(This article belongs to the Special Issue Advanced Rolling Technologies of Steels and Alloys)
  • Article
  • Open Access
8 Citations
2,666 Views
14 Pages

Investigation on the Fatigue Crack Propagation of Medium-Entropy Alloys with Heterogeneous Microstructures

  • Yang Liu,
  • Ping Jiang,
  • Guihua Duan,
  • Jing Wang and ,
  • Lingling Zhou and
  • Jijia Xie
  • + 1 author+ 0 author

1 September 2022

The behavior and the mechanism of fatigue crack propagation in CrCoNi medium-entropy alloys (MEAs) with heterogeneous microstructures were investigated in this paper. After cold-rolling and recrystallization annealing at different temperatures and ti...

(This article belongs to the Special Issue Mechanical Properties and Deformation Mechanisms of Advanced Metals and Alloys)
  • Article
  • Open Access
27 Citations
6,913 Views
16 Pages

4 August 2024

Continuous dynamic recrystallization (CDRX) forms a new recrystallized microstructure through the progressive increase in low-angle boundary misorientations (LAGBs) during the hot forming of metallic materials with high stacking fault energy (SFE), s...

(This article belongs to the Section Metal Casting, Forming and Heat Treatment)
  • Feature Paper
  • Article
  • Open Access
49 Citations
6,970 Views
15 Pages

4 November 2017

Microstructure evolution within the post-dynamic regime following hot deformation was investigated in Inconel 718 samples with different dynamically recrystallized volume fractions and under conditions such that no δ-phase particles were present. In...

(This article belongs to the Special Issue Dynamic Recrystallization Behavior of Metallic Materials)
  • Article
  • Open Access
5 Citations
3,655 Views
13 Pages

12 May 2022

As a kind of typical high stacking fault energy materials, recrystallization behavior of high purity Al-0.5%Cu alloy is significantly influenced by the annealing process. In this study, different heating rate, target temperature, and holding time wer...

(This article belongs to the Special Issue Research on Heat Treatment of Advanced Metallic Materials)
  • Article
  • Open Access
430 Views
14 Pages

Microstructural Evolution and Tensile Response of Cold-Rolled C17200 Cu-Be-Co Alloy Strip After Short-Time Annealing at 550 and 610 °C

  • Shaopeng Wu,
  • Geng Cao,
  • Dongxin Wang,
  • Junyi Li and ,
  • Jiankang Zhang,
  • Shuhui Cui,
  • Hailong Pang,
  • Mingda Han and
  • Yiqun Yang
  • + 4 authors+ 0 author

5 August 2026

This study examines the microstructural evolution and tensile response of a cold-rolled C17200 Cu–Be–Co alloy strip after short-time annealing at 550 and 610 °C. X-ray diffraction (XRD), electron backscatter diffraction (EBSD), kernel...

(This article belongs to the Section Metal Casting, Forming and Heat Treatment)
  • Article
  • Open Access
8 Citations
3,316 Views
8 Pages

25 August 2022

The flow stress and dynamic recrystallization behavior of A356 aluminum alloy was studied, with a strain rate ranging from 0.001 s−1 to 1 s−1 and temperature ranging from 300 to 500 °C. Both the true stress–strain curves and mic...

(This article belongs to the Section Computation and Simulation on Metals)
  • Article
  • Open Access
45 Citations
4,970 Views
14 Pages

Hot Deformation and Dynamic Recrystallization Behavior of CoCrNi and (CoCrNi)94Ti3Al3 Medium Entropy Alloys

  • Hai-long Yi,
  • Daixiu Wei,
  • Yingchen Wang,
  • Liqiang Wang and ,
  • Ming-yang Fang,
  • Kang Yang and
  • Hidemi Kato
  • + 2 authors+ 0 author

7 October 2020

The CoCrNi and precipitate-hardened (CoCrNi)94Ti3Al3 medium entropy alloys (MEAs) have attracted much attention, due to their exceptional mechanical properties, whereas the hot deformation characteristics have not been revealed. In the present study,...

(This article belongs to the Section Metal Casting, Forming and Heat Treatment)
  • Article
  • Open Access
10 Citations
4,178 Views
13 Pages

9 June 2022

Wire arc additive manufacturing (WAAM) involves the deposition of weld beads layer by layer using an electric arc energy source. However, during this procedure, the properties of each layer may differ because of unequal thermal distribution, resultin...

(This article belongs to the Special Issue Processing Optimization and Performance Characterization of Additively Manufactured Metallic Materials)
  • Article
  • Open Access
17 Citations
2,661 Views
13 Pages

28 June 2021

The grain refinement mechanisms along the material flow path in pure and high-purity Al were examined, using the marker insert and tool stop action methods, during the rapid cooling friction stir welding using liquid CO2. In pure Al subjected to a lo...

(This article belongs to the Special Issue Dynamic Recrystallization Behaviors in Metals and Alloys)
  • Article
  • Open Access
4 Citations
2,514 Views
10 Pages

7 October 2021

In this study, the effects of decarburization annealing time on the primary recrystallization microstructure, the texture and the magnetic properties of the final product of 0.047% Nb low-temperature grain-oriented silicon steel were investigated by...

(This article belongs to the Special Issue Metallurgical Slag)
  • Article
  • Open Access
8 Citations
3,544 Views
11 Pages

Evolution of Recrystallized Grain and Texture of Cold-Drawn Pure Mg Wire and Their Effect on Mechanical Properties

  • Jiao Meng,
  • Liuxia Sun,
  • Yue Zhang,
  • Feng Xue and ,
  • Chenglin Chu and
  • Jing Bai
  • + 1 author+ 0 author

16 January 2020

Static recrystallization plays a key role in the fabrication of thin Mg wires as well as the mechanical properties of the final wires. The effect of annealing parameters on the evolution of the microstructures, textures and mechanical properties of c...

  • Article
  • Open Access
5 Citations
3,105 Views
10 Pages

Effects of Repetitive Upsetting Extrusion on the Microstructure and Texture of GWZK124 Alloy under Different Starting Temperatures

  • Guanshi Zhang,
  • Zhimin Zhang,
  • Yingze Meng,
  • Zhaoming Yan and ,
  • Xin Che and
  • Xubin Li
  • + 1 author+ 0 author

31 July 2019

The effects of repetitive upsetting extrusion under different starting temperatures on the microstructure and texture of GWZK124 alloy were investigated. The results clearly showed that the particles and second phases induced dynamic recrystallizatio...

  • Article
  • Open Access
39 Citations
3,700 Views
20 Pages

Hot Deformation Behavior Considering Strain Effects and Recrystallization Mechanism of an Al-Zn-Mg-Cu Alloy

  • Lei Luo,
  • Zhiyi Liu,
  • Song Bai,
  • Juangang Zhao and ,
  • Diping Zeng,
  • Jian Wang,
  • Jing Cao and
  • Yangcheng Hu
  • + 3 authors+ 0 author

9 April 2020

The hot deformation behavior of an Al-Zn-Mg-Cu alloy was investigated by hot compression test at deformation temperatures varying from 320 to 440 °C with strain rates ranging from 0.01 to 10 s−1. The results show that the Mg(Zn, Cu)2 particles as a r...

  • Article
  • Open Access
3 Citations
2,113 Views
17 Pages

26 June 2025

One major challenge of friction stir processing (FSP) is its sensitivity to parameters like advancing and rotational speeds. This study examined the effect of tool travel speed on the microstructural evolution and mechanical properties of a new-gener...

  • Feature Paper
  • Article
  • Open Access
7 Citations
3,637 Views
15 Pages

Dependence of Charpy Impact Properties of Fe-30Mn-0.05C Steel on Microstructure

  • Jianchao Xiong,
  • Heng Li,
  • Ling Kong,
  • Xiaodan Zhang and ,
  • Wenquan Cao and
  • Yuhui Wang
  • + 1 author+ 0 author

18 February 2023

Fe-30Mn-0.05C steel specimens with cold-rolled, partially recrystallized, fine-grained, and coarse-grained microstructures were fabricated by means of 80% cold rolling followed by annealing at 550–1000 °C. The initial and deformed microstru...

(This article belongs to the Special Issue Dislocations and Twinning in Metals and Alloys)
  • Article
  • Open Access
4 Citations
1,466 Views
19 Pages

Hot Deformation Behavior and Dynamic Recrystallization Mechanism of GH3230 Superalloy

  • Shichong Yuan,
  • Yanhui Liu,
  • Hua Zhang,
  • Hao Li and ,
  • Qing Li and
  • Jinshan Li
  • + 1 author+ 0 author

4 November 2025

An isothermal hot compression test of GH3230 was carried out under deformation conditions with deformation temperatures ranging from 1020 to 1110 °C and strain rates ranging from 1 to 0.001 s−1. On this basis, the corresponding constitutive...

  • Article
  • Open Access
10 Citations
5,779 Views
13 Pages

Effect of the Annealing Process on the Microstructure and Performance of 5056 Aluminum Alloy Wires

  • Gaosong Wang,
  • Chong Peng,
  • Boyang Zhang,
  • Zhaoyu Xu and ,
  • Qiangqiang Li,
  • Kun Liu and
  • Pengwei Lu
  • + 2 authors+ 0 author

10 May 2022

Recrystallization can affect the mechanical properties of aluminum alloys by changing the grain structure, and even the secondary recrystallization will cause a sudden change in the grain size in the alloy. In this work, by choosing different anneali...

  • Article
  • Open Access
1 Citations
1,739 Views
11 Pages

Effect of Trace Bismuth on Deformation Behavior of Ultrahigh-Purity Copper during Hot Compression

  • Haitao Liu,
  • Yunxiao Hua,
  • Weiqiang Li,
  • Zhenguo Hou and ,
  • Jincan Dong and
  • Yong Liu
  • + 1 author+ 0 author

1 October 2024

The effect of trace Bi impurities on the flow stress, microstructure evolution, and dynamic recrystallization (DRX) of the ultrahigh-purity copper was systematically investigated by a hot compression test at 600 °C. The results show that the peak...

(This article belongs to the Special Issue Surface Modification of Advanced Transition Metal-Based Materials for Electrochemical Energy Storage)
  • Article
  • Open Access
168 Views
16 Pages

Evolution and Inheritance Characteristics of Microtexture During Recrystallization Annealing of High-Strength Ti-3Al-2.5V Titanium Alloy Tubes

  • Haote Xiang,
  • Jianhao Feng,
  • Xuan Zhang,
  • Meng Li and ,
  • Manfeng Gong,
  • Dong Wei,
  • Duo Zhang and
  • Heng Yang
  • + 3 authors+ 0 author

15 October 2026

This study investigates the microstructure and texture inheritance of cold-pilgered Ti-3Al-2.5V titanium alloy tubes for aerospace hydraulic systems during recrystallization annealing at 590 °C, 620 °C, and 720 °C. Tubes with radial and c...

(This article belongs to the Special Issue Recent Advances in Plastic Forming of Metals)
  • Article
  • Open Access
8 Citations
3,820 Views
19 Pages

18 February 2022

In a thermal simulator of Gleeble-3500, isothermal hot compression tests were performed on a Ni-Cr-Co-based superalloy at deformation temperatures ranging from 1323 K to 1423 K and with strain rates of 0.01, 0.1, 1, and 5 s−1. We obtained the t...

(This article belongs to the Topic Processing, Analysis, Modelling and Mechanics of Materials and Structures)
  • Article
  • Open Access
10 Citations
3,180 Views
18 Pages

12 May 2024

The exploration of the relationship between process parameters and grain evolution during the thermal deformation of rare-earth magnesium alloys using simulation software has significant implications for enhancing research and development efficiency...

(This article belongs to the Special Issue Modeling, Simulation and Experimental Studies in Metal Forming)
  • Article
  • Open Access
2 Citations
891 Views
12 Pages

24 January 2026

We investigated the effects of two-way cold rolling and subsequent annealing on the microstructure and tensile properties of low-carbon steel with different initial microstructures. Two types of hot-rolled sheet specimens were prepared: specimen P, c...

(This article belongs to the Special Issue Advanced Steel Materials: Recrystallization, Phase Transformation and Microstructure Analysis (Second Edition))
  • Article
  • Open Access
14 Citations
4,333 Views
20 Pages

Hot Deformation Behavior of Q345 Steel and Its Application in Rapid Shear Connection

  • Mengwei Wu,
  • Shuangjie Zhang,
  • Shibo Ma,
  • Huajun Yan and ,
  • Wei Wang and
  • Qiang Li
  • + 1 author+ 0 author

7 July 2019

The high-temperature deformation behavior of Q345 steel is detected by a Gleeble-3800 thermal simulator. The Arrhenius constitutive equation for high-temperature flow stress and the dynamic recrystallization model are constructed. With the secondary...

(This article belongs to the Special Issue Development of the Rolling Process in Metallic Materials)
  • Article
  • Open Access
12 Citations
5,878 Views
15 Pages

8 November 2018

Titanium alloys with high stacking-fault energy show continuous dynamic recrystallization (CDRX) instead of discontinuous dynamic recrystallization (DDRX) during high-temperature deformation. During the CDRX mechanism, new recrystallized grains are g...

(This article belongs to the Special Issue Dynamic Recrystallization Behavior of Metallic Materials)
  • Article
  • Open Access
5 Citations
1,854 Views
19 Pages

Unveiling the Microstructural Features during Compression of a High-Modulus Mg-15Gd-8Y-6Al-0.3Mn Alloy Reinforced by a Large Volume of Al2RE Phases

  • Xuhui Feng,
  • Xiaojun Wang,
  • Chao Xu,
  • Hailong Shi and ,
  • Xuejian Li,
  • Xiaoshi Hu,
  • Zhen Lu and
  • Guohua Fan
  • + 3 authors+ 0 author

29 September 2024

Magnesium alloys with a high volume fraction of secondary phases exhibit inferior formability. Therefore, investigating their thermal deformation characteristics is critical for optimizing thermal processing techniques. In this work, isothermal compr...

(This article belongs to the Special Issue Study on Advanced Metal Matrix Composites (2nd Edition))
  • Article
  • Open Access
72 Views
22 Pages

High-Temperature Hot Deformation Behavior and Processing Map of TC11 Titanium Alloy

  • Yanchun Zhu,
  • Yefan Li,
  • Jie Lu,
  • Shijie Wang and ,
  • Lei Liu,
  • Zhibing Chu,
  • Shangwu Jia,
  • Yong Niu and
  • Fan Wang
  • + 4 authors+ 0 author

4 November 2026

In this study, the high-temperature deformation behavior of TC11 titanium alloy was investigated through hot compression experiments. The relationship between flow stress, strain rate, and deformation temperature was described by analyzing stress&nda...

(This article belongs to the Section Metal Casting, Forming and Heat Treatment)
  • Article
  • Open Access
11 Citations
5,208 Views
21 Pages

Analysis of Recrystallization Kinetics Concerning the Experimental, Computational, and Empirical Evaluation of Critical Temperatures for Static Recrystallization in Nb, Ti, and V Microalloyed Steels

  • Evelyn Sobotka,
  • Johannes Kreyca,
  • Robert Kahlenberg,
  • Aurélie Jacob and ,
  • Ernst Kozeschnik and
  • Erwin Povoden-Karadeniz
  • + 1 author+ 0 author

3 May 2023

Recrystallization kinetics and two critical temperatures—the non-recrystallization temperature TNR and the static recrystallization critical temperature TSRCT—of five Nb, Ti, and V microalloyed steel grades are evaluated. The experimental...

(This article belongs to the Section Metal Casting, Forming and Heat Treatment)
  • Article
  • Open Access
13 Citations
2,668 Views
16 Pages

29 March 2024

The mechanical properties of metastable β-titanium alloys are highly susceptible during the thermal mechanical processing (TMP). In this process, the recrystallization process plays an important role in determining the microstructure and texture...

(This article belongs to the Section Metals and Alloys)
  • Article
  • Open Access
4 Citations
1,750 Views
17 Pages

9 April 2025

The influence of annealing temperature on the mechanical properties, microstructural evolution, and recrystallization behavior of AA5083 cold-rolled sheets with and without Sc/Zr microalloying was studied utilizing hardness tests, optical microscopy,...

(This article belongs to the Special Issue Processing of Metals and Alloys)
  • Article
  • Open Access
30 Citations
6,427 Views
14 Pages

The Effect of Ultrafast Heating in Cold-Rolled Low Carbon Steel: Recrystallization and Texture Evolution

  • Felipe M. Castro Cerda,
  • Leo A. I. Kestens,
  • Alberto Monsalve and
  • Roumen H. Petrov

21 November 2016

The microstructure and texture evolution of cold-rolled low carbon steel after ultrafast heating and quenching is investigated. Experiments were carried out at heating rates of 150 °C/s and 1500 °C/s. The recrystallization of ferrite is studied by sc...

  • Article
  • Open Access
6 Citations
3,699 Views
7 Pages

Structural Evolution of Bulk Silver during Cold Rolling and Annealing

  • Zheda Ning,
  • Qunshou Wang,
  • Dong Zhao,
  • Wenli Pei and
  • Ming Wen

15 September 2022

Sputtering target is commonly used in semiconductor manufacturing for the preparation of thin films. Cold rolling and annealing treatment of bulk Ag is the routine process to prepare Ag sputtering target. In this paper, the microstructure evolution o...

(This article belongs to the Special Issue Metallic Functional Materials)
  • Article
  • Open Access
4 Citations
3,445 Views
14 Pages

Primary Recrystallization Behaviors of Hi-B Steel with Lower Initial Nitrogen Produced by the Thin Slab Casting and Rolling Process

  • Bing Fu,
  • Li Xiang,
  • Jia-Long Qiao,
  • Hai-Jun Wang and ,
  • Jing Liu and
  • Sheng-Tao Qiu
  • + 1 author+ 0 author

21 January 2021

Based on low-temperature high-permeability grain-oriented silicon steel designed with an initial nitrogen content of 0.0055% and produced by the thin slab casting and rolling process, the effect of total nitrogen content and nitriding temperature on...

(This article belongs to the Special Issue Microstructure-Mechanical Property Relationships in Metallic Materials)
  • Article
  • Open Access
3 Citations
1,244 Views
14 Pages

Grain Refinement Caused by Dynamic Recrystallization Under Pulsed-Wave Laser Multi-Layer Cyclic Thermal Load

  • Manping Cheng,
  • Xi Zou,
  • Yuan Zhu,
  • Tengfei Chang and ,
  • Qi Cao,
  • Houlai Ju,
  • Jiawei Ning,
  • Yang Ding and
  • Lijun Qiang
  • + 4 authors+ 0 author

In the Direct Energy Deposition (DED) process, the deposited material experiences intricate thermo-mechanical processes. Subsequent thermal cycling can trigger Dynamic Recrystallization (DRX) under suitable conditions, with specific strain and temper...

  • Article
  • Open Access
8 Citations
2,543 Views
17 Pages

Modeling of Dynamic Recrystallization Evolution for Cr8 Alloy Steel and Its Application in FEM

  • Xuewen Chen,
  • Bingqi Liu,
  • Bo Zhang,
  • Jiawei Sun and ,
  • Zhen Yang,
  • Xudong Zhou,
  • Tao Huang and
  • Danqing Yin
  • + 3 authors+ 0 author

1 October 2022

In the process of Cr8 roller production, the phenomenon of coarse grain size and uneven grain size often appears, which makes the mechanical properties of the material decrease sharply. Accurate dynamic recrystallization model is the basis for predic...

(This article belongs to the Special Issue Processing–Microstructure–Properties Loop in Materials and Metallurgical Engineering)
  • Article
  • Open Access
7 Citations
3,004 Views
16 Pages

Hot Deformation Behavior and Microstructure Evolution of Fe–5Mn–3Al–0.1C High-Strength Lightweight Steel for Automobiles

  • Guangming Liu,
  • Jinbin Wang,
  • Yafeng Ji,
  • Runyuan Hao and ,
  • Huaying Li,
  • Yugui Li and
  • Zhengyi Jiang
  • + 2 authors+ 0 author

11 May 2021

The hot deformation behavior of a newly designed Fe–5Mn–3Al–0.1C (wt.%) medium manganese steel was investigated using hot compression tests in the temperature range of 900 to 1150 °C, at constant strain rates of 0.1, 1, 2.5, 5, 10, and 20 s−1. A deta...

  • Article
  • Open Access
8 Citations
2,750 Views
12 Pages

29 April 2022

The large diameter titanium alloy bars are usually manufactured by forging, which leads to large metal loss, high cost, low efficiency and limited product specifications. This paper adopted three-high skew rolling technology to roll Ti–6Al&ndas...

  • Article
  • Open Access
2 Citations
2,055 Views
19 Pages

26 March 2025

The hot deformation behavior of the near-α titanium alloy TA32 (Ti-5.5Al-3.5Sn-3Zr-1Mo-0.5Nb-0.7Ta-0.3Si) was studied by isothermal compression tests. The deformation temperatures ranged from 700 to 950 °C, with strain rates ranging from 0....

  • Article
  • Open Access
3 Citations
1,197 Views
13 Pages

Investigation on Hot Deformation Behavior and Microstructural Evolution of Al-Mg-Zn Aluminum Alloy via Uniaxial Isothermal Hot Compression Tests

  • Fei He,
  • Junzhe Huang,
  • Kai Zhu,
  • Xiwu Li and ,
  • Kai Wen,
  • Guanjun Gao,
  • Lizhen Yan,
  • Hongwei Yan,
  • Zhihui Li and
  • Baiqing Xiong
  • + 6 authors+ 1 author

27 October 2025

In this study, we investigated the hot deformation behavior and microstructural evolution of a novel high-magnesium-content (high-Mg) aluminum alloy, bridging the disciplines of material processing and physical metallurgy. Uniaxial hot compression te...

(This article belongs to the Section Metals and Alloys)

of 30