In order to solve the problem of high straw content in recovered residual film and the low rate of qualified straw crushing in combination with a front-mounted cotton-straw-crushing device, the cutting and crushing mechanisms of cotton stalks were st...
Modern power engine concepts and environmental restrictions demand oil-free lubrication of rotors, for example, by gas bearings. However, the stiffness and damping properties ruling the rotor’s dynamics are poorly documented for aerodynamic bea...
Electric vehicles (EVs) should have an electrical motor with high efficiency, high power density, and a wider constant power operating region, as well as ease of control and inexpensive manufacturing cost. To achieve these requirements, a real-time c...
The extreme environment of aerospace requires severe material properties, and in situ autogenous ZrC–NbC dual-phase reinforced titanium matrix composites have attracted much attention. In this study, TiC/Ti composites (TMC1–TMC4) with dif...
The article addresses the modeling of the process of manufacturing a large-sized shell, given the thermomechanical behavior and viscoelasticity of the composite mandrel. The results of the experimental identification of viscoelasticity parameters of...
In this paper, a multi-transmitting formula (MTF) was integrated into ANSYS software through secondary development, enabling dynamic finite element simulation of wave propagation in infinite domains. The numerical reliability and accuracy of the MTF...
During the Fused Deposition Modeling (FDM) molding process, temperature changes are nonlinear and instantaneous, which is a key parameter affecting FDM printing efficiency, molding accuracy, warpage deformation, and other factors. This study presents...
To solve the problems of low net harvesting rate, high loss rate, and uneven stubble height during the harvest of laver, the laver (Porphyra yezoensis) was selected as the research object, the analysis of the cultivation mode, biomechanical character...
Harvesting of laver is an important link in the laver culture chain, and a new type of corrugated harvesting blade with a curved edge angle was designed to solve the problems of low cutting ratio in laver harvesting. The mechanical model of the corru...
Based on the thickness of the common ice layer in the Heilongjiang Basin, explosions featuring different methods of firing, different thicknesses of the common ice layer, and different distances between the explosive and the ice are hereby simulated...
The process of fully mechanized coal seam mining under aquifers and surface water bodies has been a challenge in recent years for different countries. During the evolution of subsidence and the overburdening of rock mass movement above the longwall g...
Mechanical components are more difficult to detect at the initial state of failure. To solve this problem, this paper models and simulates the characteristics of an electrostatic oil-line sensor (OLS) wear particles carried in the lubricating oil pat...
The distribution of heating gun ends plays a decisive role in the sidewall properties of finished rotomolded products. To obtain the optimal distribution of the end face of a rotational molding heating gun, the temperature response of the end-face mo...
This paper utilizes computational fluid dynamics as well as a group method of data handling (GMDH) method to predict the mean velocity of intake. Firstly, the three dimensional flow pattern in a 90-degree intake is simulated with ANSYS-CFX at a trans...
This manuscript presents a fully detailed methodology in order to identify the hydrodynamic parameters of a mini autonomous underwater vehicle (mini-AUV) and evaluate its performance using different controllers. The methodology consists of close-to-r...
With the development of large-scale projects such as high-rise buildings, deep-sea platforms, bridges, etc., these construction facilities are affected by many factors such as environment and geological conditions, which put forward higher requiremen...
An ultrasonic spray pyrolysis (USP) device consists of an evaporation and two reaction zones of equal length, into which an aerosol with a precursor compound enters, and where nanoparticles are formed in the final stage. As part of this research, we...
This work presents a simulation model developed with the aim to represent and study the thermal behavior of cyclotron liquid targets. Understanding and improving the thermal behavior of the target system is fundamental to improving the target overall...
Flow control valves are designed to maintain a constant flow rate regardless of pressure changes. However, standard, two-way design may cause significant energy losses due to the need to maintain high pressure in the supply line. In contrast, the pro...
The prediction of welding distortion requires expertise in computer simulation programs, a clear definition of the nonlinear material properties, and mesh settings together with the nonlinear solution settings of a coupled thermal–structural analysis...
The atmospheric flow and dispersion of traffic exhaust were numerically studied in this work while considering a model street canyon intersection of a city. The finite volume method (FVM)-based large-eddy simulation (LES) technique in line with ANSYS...
This study investigates the impact of the bearing plate position on the uplift bearing capacity of low-header concrete expanded pile (CEP) foundations using the ANSYS finite element simulation method. Nine models of low-header CEP single piles with v...
The finite element analysis (FEA) is an essential and powerful numerical method that can explicitly optimize the design process of electrical devices. In this paper, the employment of the finite element method (FEM) as ANSYS is proposed in order to a...
As electric vehicles (EVs) face increasing power demands, rapid charging requirements, and harsh operating conditions, efficient thermal management of lithium-ion batteries is critical for safety and performance. This study evaluates a liquid-cooled...
Simple analog devices like manometers, manual valves, etc., have been ignored in the digitization process that has characterized the transition towards Industry 4.0. The reason behind this is that their substitution with the equivalent digital versio...
In this study, the evolution of mechanical properties, microstructure, and residual stresses during selective laser melting of CuSn10 components was studied. To provide a proper material model for the simulations, various CuSn10 parts were manufactur...
Binder jetting is a crucial process in additive manufacturing (AM) and is widely used in sand mold casting. This study explores the challenges of simulating binder droplets in ANSYS Fluent, including complexity and computational time. To overcome the...
The aim of this paper is to analyze the heat distribution in the high-current electrical contact under the action of an assumed current of 3000 A using mathematical modeling and simulation. Electrical contacts that carry high currents are an essentia...
One simple, efficient, reliable, and inexpensive method to protect the inner surface of slim tubes prior to exposure to corrosion is to apply a dispersed oil fraction through a nozzle and a mixing valve to prepare a mixture of air and oil applied on...
Several previous experiments showed that the leapfrog–hopscotch and the adapted Dufort–Frankel methods are the most efficient among the explicit and stable numerical methods to solve heat transfer problems in building walls. In this paper...
Wafer-level processed and wafer-level packaged low-cost microelectromechanical system (MEMS) thermal sensors are required for a wide range of Internet of Things (IoT) and wearables applications. Recently, a new generation of uncooled thermal sensors...
The reduction of building energy consumption requires appropriate planning and design of the building’s envelope. In the last years, new innovative materials and construction technologies used in new or refurbished buildings have been developed in or...
Wood is a cellulosic material that is most abundantly available in nature. Wood has been extensively used as reinforcement in polymer composite materials. Wood polymer composite (WPC) is an environmentally friendly and sustainable material exploited...
There is a lack of detailed information about wind flow and distribution of wind pressure around atypically shaped high-rise buildings. The national standard EN 1991-1-4 Eurocode 1 used to determine the effects of wind on the territory of Slovakia (a...
This study aims to create an iconic dust-control skyscraper that resembles an environmentally friendly structure, by adapting a new dust simulation design approach. This method seeks to reduce dust dispersion in the air, control dust movement, and si...
Composite materials have a wide range of functional properties, which is ensured by using various technological methods of obtaining both the matrix or fillers and the composition as a whole. A special place belongs to the composition formation techn...
Model validation is an essential part of CFD-based projects. Despite being successfully employed for decades, the level and extent of CFD model validation details vary significantly in the published literature, which, in turn, adversely affects the r...
Thermal solar systems are currently one of the most suitable ways to convert solar radiation into usable energy. To ensure maximum energy gain, it is necessary to correctly adjust the direction of the collectors in the southern direction. The deviati...
The seismic response of underground liquefied natural gas (LNG) storage tanks has been a significant focus in both academic and engineering circles. This study utilized Ansys (2021R1) to conduct seismic analyses of large-capacity LNG tanks, consideri...
Precast reinforced concrete (RC) girders with dapped ends are used in order to reduce the overall depths of concrete floors and bridge decking and meet architectural requirements. The structural requirements by reducing the depths of these girders re...
Phase change materials (PCMs) have a large number of applications for thermal energy storage (TES) and temperature reduction in buildings due to their thermal characteristics and latent heat storage capabilities. The thermal mass of typical brick wal...
Photovoltaic power plants are gaining in popularity and availability every year, resulting in a massive increase in their number and size. However, each such investment involves allocating large land areas, the cost of which may be high. For this rea...
Geopolymer concrete is preferred over OPC due to its use of energy waste such as fly ash, making it more sustainable and energy-efficient. However, limited research has been done on its seismic characterization in confined masonry, highlighting a gap...
The ability of an off-road robot to traverse obstacles determines whether the robot can complete complex environmental tasks. In order to improve the off-road ability of off-road robots, this paper proposes a new design idea, in which four hub motors...
How to improve the power generation of wave energy converters (WEC) has become one of the main research objectives in wave energy field. This paper illustrates a framework on the use of back propagation (BP) neural network in predicting capture power...
Soybeans are a crucial crop, and it is therefore necessary to make accurate predictions of their mechanical properties during harvesting to optimize the design of threshing cylinders, minimize the breakage rate during threshing, and enhance the quali...
Titanium alloy is widely used as a biomaterial due to its strength, lightweight nature, and corrosion resistance. Despite its strength and lightweight nature, its low wear resistance limits its uses in prosthetic components. Laser surface texturing (...
The shield tunnel is a common solution for natural gas pipelines crossing rivers. Consequently, the development of natural gas tunnel filling materials with excellent performance is crucial to the safe operation and maintenance of pipelines. The foam...
Non-prismatic reinforced concrete (RC) beams are widely used for various practical purposes, including enhancing architectural aesthetics and increasing the overall thickness in the support area above the column, which gives high assurance to service...
A gas turbine power plant in Thailand had the problem of compressor blade fracture in Stages 6–8, which was caused by housing damage. This gas turbine has a total of 15 stages. The housing damage reduced the lifetime of blades to an unacceptabl...
of 42