Some modern alloys, such as high-entropy alloys (HEAs), are emerging with greater acceleration due to their wide range of properties and applications. HEAs can be prepared from many metallurgical operations, but mechanical alloying is considered to b...
Aluminium metal matrix composites (AMMCs) incorporate aluminium alloys reinforced with fibres (continuous/discontinuous), whiskers, or particulate. These materials were engineered as advanced solutions for demanding sectors including construction, ae...
Nickel is an important and widely used alloying element in carbon steels. Some of its prominent metallurgical effects in these steels are moderate solid solution strengthening, mild hardenability and, importantly, a strong promotion of toughness, esp...
Additive manufacturing (AM) of metals can be broadly accomplished via two defined technologies: powder bed fusion and directed energy deposition. During AM fabrication, the melted feedstock material experiences fast thermal cycling due to the layer-b...
Residual stress is caused by non–uniform deformation caused by non–uniform force, heat and composition, which is of great significance in engineering applications. It is assumed that the residual stress is always the upper limit of the el...
The classic Cantor (FeCoCrMnNi) isoatomic high entropy alloy was modified by separate additions of Mo and Nb in an effort to optimize its mechanical properties and sliding wear response. It was found that the introduction of Mo and Nb modified the si...
Al–Mg–Si alloys are used in aircraft, train, and car manufacturing industries due to their advantages, which include non-corrosivity, low density, relatively low cost, high thermal and electrical conductivity, formability, and weldability...
One of the main challenges encountered in the Laser-based Powder Bed Fusion (L-PBF) Additive Manufacturing (AM) process is the fabrication of defect-free parts. The presence of defects severely degrades the mechanical performance of AM parts and espe...
Half-Heusler alloys are promising materials for thermoelectric applications, yet the impact of the compositional disorder on their lattice dynamics remains incompletely understood. This study investigates the effect of systematic Zr substitution on t...
Aluminum is widely used in many industries like automotive, aerospace and construction because of its low weight, good mechanical strength and resistance to corrosion. This resistance comes mainly from a passive oxide layer that forms on its surface....
High-entropy alloys (HEAs) present a vast compositional design space, characterized by four core effects—high configurational entropy, sluggish diffusion, severe lattice distortion, and the cocktail effect—which collectively underpin thei...
Ultrasonic-assisted Ti6Al4V Directed Energy Deposition (DED) additive manufacturing technology can improve the problem of uneven microstructure caused by laser heating and sudden cooling of the molten pool. In this paper, the numerical analysis and e...
The grain boundaries and dislocations play an important role in understanding the deformation behavior in polycrystalline materials. In this paper, the deformation mechanism of Cu, Ni, and equimolar Cu-Ni alloy was investigated using molecular dynami...
A new approach for the development of thermoelectric materials, which focuses on a high-power factor instead of a large figure of merit zT, has drawn attention in recent years. In this context, the thermoelectric properties of Cu-Ni-based alloys with...
Transition metal-ruthenium alloys are promising candidates for ultra-high-temperature structural applications. However, the mechanical and electronic characteristics of these alloys are not well understood in the literature. This study uses first-pri...
The isothermal oxidation of a Fe35Mn21Ni20Cr12Al12 high entropy alloy (HEA) was investigated in dry air for 50 h at 500, 600, and 700 °C after 90% cold rolling. The Fe35Mn21Ni20Cr12Al12 HEA behaves according to the linear oxidation rate with rate...
Permanent magnets are becoming more and more relevant for modern society. As the most widely used permanent magnets contain rare-earth elements, the increased dependence on these strategic elements is worrisome, and the pursuit for rare-earth free al...
Carbide-free bainitic steels show attractive mechanical properties but are difficult to process because of the sluggish phase transformation kinetics. A macroscopic model based on the classical nucleation theory in conjunction with the modified Koist...
A systematic study of the phase composition of quenched binary titanium alloys with d-metals of groups 5–11 from periods four to six was carried out using the methods of X-ray diffraction analysis. It was found that the formation of the orthorh...
Varying contents of carbon, titanium and boron were used in the base steel composition of 0.30 wt% Si, 2.0 wt% Mn, 0.006 wt% S, 0.03 wt% Nb, and 30–35 ppm N. Hot ductility tests were performed with Gleeble-3800, after the steel sample was in-si...
The demand for high-strength aluminum alloys for the laser powder bed fusion (LPBF) process is still growing. However, to date, the crack susceptibility of conventional alloys as well as the high prices for specially developed alloys are the main obs...
This study investigates the corrosion behavior of Grade 23 Ti6Al4V alloys produced through laser powder bed fusion (L-PBF) when exposed to simulated body fluid at room temperature, focusing on the role of unmelted particles. This research aims to und...
Light alloys based on magnesium are widely used in most areas of science and technology. However, magnesium powder alloys are quite difficult to sinter due to the stable film of oxides that counteracts diffusion. Therefore, finding a method to activa...
In pressurized water reactors (PWRs), flow-induced vibration (FIV) induces the fretting wear of fuel rods and supporting grids, and the process is accompanied by corrosion, which is called fretting corrosion. In this paper, fretting corrosion experim...
Additive manufacturing (AM) techniques such as laser powder bed fusion (L-PBF) are rapidly growing due to the inherent design freedom and possibilities to produce components not available with other techniques. This could be utilized in, e.g., the de...
Case-hardening steels are gaining increasing interest in the field of laser powder bed fusion (PBF-LB/M) due to their excellent weldability. In combination with post-process carburization heat treatment, the surface properties can be improved to gene...
Gold and silver are, for all their chemical similarities, optically very different. Small Ag clusters show a localized surface-plasmon resonance (LSPR), whereas in Au clusters smaller than about 300 atoms, the resonance is absent due to the coupling...
Additive manufacturing (AM) processes are not solely used where maximum design freedom meets low lot sizes. Direct microstructure design and topology optimization can be realized concomitantly during processing by adjusting the geometry, the material...
A promising approach for producing parts with outstanding properties in directed energy deposition (DED-LB/M) provides the application of tailored powder mixtures processed by applying in situ alloying strategies. In this work, DED-LB/M was used to m...
Additive manufacturing is a promising and actively developing method for the synthesis of metal products. The development of techniques for the production of spherical powder particles with specified properties from metals and alloys represents a sig...
This article presents the results of studies of the self-propagating high-temperature synthesis (SHS) for obtaining zirconium alloys with niobium by the method of calcium-thermal reduction of nuclear-grade zirconium tetrafluoride in the presence of n...
Babbitt alloys are among the most commonly used materials for sliding bearings. However, with the high speeds and heavy loads of modern machinery, as well as the demands of extreme working conditions, the temperature resistance, strength, and hardnes...
The paper is a personal perspective on the design of metallic ultra-high temperature materials (UHTMs). Specifically, the alloy design “landscape” of metallic UHTMs was considered from the viewpoint of the alloy design methodology NICE. T...
The defect evolution associated with an anomalous work hardening behavior of a single crystalline quaternary Co-Al-W-Ta superalloy at 950 °C was investigated by transmission electron microscopy. As plastic deformation is initially confined to the...
An AA6061-7075 composite with a heterogeneous structure was fabricated via the additive friction stir deposition (AFSD) method, and in situ processing data were monitored during the manufacturing process. The results show that the cross-section of th...
Laser powder bed fusion (L-PBF) is a metal additive manufacturing (AM) technique that produces a unique microstructure significantly different from wrought microstructure. Inconel 625 (IN625) is an alloy widely used to manufacture complex parts, but...
Abstract: The refractory complex concentrated alloy (RCCA) 5Al–5Cr–5Ge–1Hf–6Mo–33Nb–19Si–20Ti–5Sn–1W (at.%) was studied in the as-cast and heat-treated conditions. The partitioning of solutes in t...
The microstructure and mechanical properties of as-homogenized Mg-xLi-3Al-2Zn-0.2Zr alloys (x = 5, 7, 8, 9, 11 wt.%) were studied. As the Li content increased from 5 wt.% to 11 wt.%, the alloy matrix changed from the α-Mg single-phase to &alpha...
Titanium alloys are ideal for a great range of engineering applications; however, their high manufacturing costs hinder their widespread use. This study investigates the relationship between the processing and properties of representative Ti-based ma...
Integrated computational materials engineering (ICME) is emerging as an increasingly powerful approach to integrate computational materials science tools into a holistic system and address the multiscale modeling challenges in the processing of advan...
FeSiCr alloys are used as soft magnetic materials for power multilayer inductors. The alloys are typically annealed at intermediate temperatures in air during inductor fabrication to form an insulating chromium oxide layer around the alloy particles....
Alloy 625 is a widely utilized nickel-based superalloy known for its excellent mechanical strength and corrosion resistance in aggressive environments. However, its high niobium (Nb) content can lead to the formation of detrimental phases, such as La...
The increasing restriction of lead in industrial alloys, particularly in copper–zinc-based materials such as CuZn40Pb2, necessitates the development of environmentally safer alternatives. ZnAl15Cu1Mg (ZEP1510), a zinc-based wrought alloy compos...
In this work, the results of the structural and phase state of LaNi5-based alloys modified with Ti, Mn, and Co elements, obtained by mechanical alloying and subsequent spark plasma sintering, are presented. X-ray diffraction analysis was carried out...
The global pursuit of a sustainable and decarbonized energy landscape requires the development of novel materials capable of supporting lightweight construction, advanced energy conversion, storage, and thermal management technologies. Among these, m...
A thin-walled product made of AZ31 magnesium alloy was successfully fabricated using wire-feed electron-beam additive manufacturing. The microstructure of the initial wire, used as a precursor, comprises a α-Mg(Al, Zn) solid solution and a mino...
Machine learning (ML) is becoming an established part of alloy research, offering new ways to link composition, processing routes, and microstructure with measured properties. In this work, recent studies using ML for predicting or optimizing alloy b...
In this work, the refractory complex concentrated alloy (RCCA) 3.5Al–4Cr–6Ge–1Hf–5Mo–36Nb–22Si–1.5Sn–20Ti–1W (at.%) was studied in the as cast and heat treated conditions (100 h or 200 h at 1500 &...
Co-Cr-Mo alloy as a human body implant material has a long history, because of its excellent corrosion resistance and biocompatibility, and is widely used in human hip joint materials. Co-Cr-Mo alloy in the human body is often in a passivation state;...
The paper presents the results of the study of the processes of self-propagating high-temperature synthesis of Zr-1%B alloy and its refining by electron beam melting. Experiments on the influence of boron’s amorphous and crystalline modificatio...
