Fluids, Volume 11, Issue 4

This work investigates the impact of sample size on the measurement of non-wetting/wetting interfacial areas in porous media by X-ray microtomography (XMT). Standard-sized small columns and significantly larger columns, both packed with sand, were im...

This paper studies the dynamics of a low-density gas directly injected onto a flat wall, focusing on the influence of different pressure ratios (PRs) and plate position. Due to safety reasons, Helium (He) was employed as substitute to reproduce the m...

This study examines the electrohydrodynamic (EHD) behavior of air bubbles rising in deionized water under a non-uniform electric field, with particular emphasis on the influence of applied voltage (0.5–3.0 kV) and gas flow rates of 30 and 40 mL...

Non-Newtonian weighted fracturing fluids are used to carry out hydraulic fracturing operations into the deep and ultra-deep earth for oil and gas extraction, though their flow and friction drag characteristics are largely unknown. This study aims to...

This paper examines the sixth-order generalized Boussinesq equation, which describes the dynamics of shallow-water waves, including the effects of surface tension. The study introduces Kudryashov’s R-function neural network approach for the fir...

A wall-dependent identification method for low-speed streamwise streaks in turbulent channel flows is presented to overcome a key limitation of uniform thresholds, which tend to produce either an excess of detected structures near the wall or an appa...

The hydrojet-shield machine, a rapidly advancing shield machine type, uses slurry for excavation and muck removal via a pipeline system. The pipeline includes a flushed feeding system that injects slurry into areas at risk of obstruction. This study...

Pressure fluctuations caused by a jet in crossflow (JICF) can induce cavitation and potentially damage wall surfaces. In mercury targets for a pulsed spallation neutron source, where cavitation damage progresses due to thermal shock, mercury is confi...

The growing need to mitigate climate change has accelerated the development of Carbon Capture, Utilization, and Storage (CCUS) technologies, where the safe transport of supercritical CO₂ (sCO₂) through pipelines is a key challenge. The flow behavior...

This study investigates the dripping and leakage problem in kitchenware known as the “teapot effect” through a multidisciplinary experimental approach encompassing fluid mechanics, material science, and ergonomic design. Unlike previous s...

Hydraulic transients in pressurized pipe systems are significantly influenced by the presence of entrapped air, which alters wave propagation through increased compressibility and energy dissipation. Traditional discrete cavity models, such as the Di...

To improve unified modeling of steady two-dimensional lid-driven cavity flow across a wide range of Reynolds numbers, this study proposes a Vorticity-Enhanced Physics-Informed Neural Network (VE-PINN). The method augments a standard velocity-pressure...

This paper investigates the combustion dynamics of interacting lazy multi-component gas plumes (i.e., buoyancy-dominated gas releases with a low initial momentum flux), a configuration relevant to coal mining waste emissions. By coupling a three-dime...

Nearly all biological fluids and a vast number of non-biological fluids are, to some extent, non-Newtonian, with many also exhibiting viscoelastic responses [...]

Indoor exposure to particulate matter (PM) depends on ventilation-driven transport, yet sensor placement in real rooms is often based on limited point data. This study develops and experimentally validates a transient CFD framework, using RANS airflo...

In this work, we assess the reliability of a new Bhatnagar–Gross–Krook (BGK)-type model of the linearized Boltzmann equation for binary gas mixtures by investigating the propagation of high-frequency sound waves in microchannels. In order...

Shark skin grooves, known to reduce hydrodynamic drag, have inspired riblet structures for flow control. This study investigates their application to airfoils, where flow separation at high angles of attack (AOA) compromises aerodynamic stability and...

The valve serves as the actuating component within the valve mechanism. Under braking conditions, the valve is prone to swaying, which significantly compromises the reliability and service life of the engine. Hence, this paper focuses on researching...

To address the issues of high impurity rates and grain loss during the wheat cleaning process, a coupled Computational Fluid Dynamics (CFD) and Discrete Element Method (DEM) approach was employed to investigate the internal airflow field and the flui...

Rational design of high-performance viscosifying polymers is critical for enhancing supercritical CO₂ flooding efficiency in enhanced oil recovery (EOR). Traditional experimental and simulation approaches are limited in exploring the vast design spac...

Gas–liquid multiphase pumps are essential for deep-sea oil and gas production; however, their performance is severely limited under high gas volume fraction (GVF > 30%) conditions due to inefficient energy transfer and flow instability. In t...