Nowadays, numerical simulation methods are advanced and widely used in industry, enabling the modeling of complex systems from printed circuit boards (PCBs) to full power converters. Among many isolated topologies, the phase-shift full-bridge (PSFB)...
Newly constructed devices must meet a number of requirements in terms of the level of generated disturbances. To achieve an acceptable level in such devices, filters are installed—one of the cheapest ways to reduce interference in devices. One...
Switched-mode power supplies are very efficient and commonly used components in products nowadays. However, due to currents switched at a high frequency, the conducted emission test is a high concern for designers. The market is increasingly demandin...
Electric vehicles (EVs) pose electromagnetic compatibility (EMC) and electromagnetic interference (EMI) challenges that span sub-hertz traction currents to multi-gigahertz radiated emissions. This paper combines a narrative review of 260 publications...
This paper describes the design of an electromagnetic interference (EMI) filter for the high-frequency link matrix converter (HFLMC). The proposed method aims to systematize the design process for pre-compliance with CISPR 11 Class B standard in the...
In order to ensure the vehicle management system (VMS) satisfy the RE and CE standards which are required by national regulations, the EMC design method is necessary to be integrated into the controller PCB design flow. Through filtering for signal l...
FAT atypical cadherin 1 (FAT1) regulates cell-cell adhesion and extracellular matrix architecture, while acting as tumor suppressor or oncogene, context-dependently. Despite implication of FAT1 in several malignancies, its role in oral squamous cell...
Road lighting systems require a significant amount of electric energy. To compensate for the utilized energy, the concept of a nanogrid road lighting system is presented. A solar panel is installed on the top of a lighting pole to generate electric p...
The interconnection of different electronic devices or systems through cables is becoming more difficult due to the hard restrictions related to electromagnetic compatibility (EMC) in order to comply with requirements. Therefore, the use of EMC compo...
The motor integration of singe-phase-supplied Variable-Speed Drives (VSDs) is prevented by the significant volume, short lifetime, and operating temperature limit of the electrolytic capacitors required to buffer the pulsating power grid. The DC-link...
Quasi-resonant flyback (QRF) converters have been widely applied as the main circuit topology in power converters because of their low cost and high efficiency. Conventional QRF converters tend to generate higher average conducted electromagnetic int...
Background: Electromagnetic compatibility (EMC) challenges in 2.5D/3D semiconductor packaging arise from the complex coupling between device, interposer, board, and cable domains, which are insufficiently captured by conventional board-level analysis...
Filters for the suppression of the RF disturbances in power lines are passive; wideband stop filters attenuating common as well as differential disturbances should be insensitive to the variation in the impedance at the input and the output. The desi...
A road lighting system is important for drivers and uses a lot of energy. The road lighting system must be installed throughout roads which have a long distance and a large volume, which causes power loss in the power transmission line. The concept o...
Interference in Power Line Communication (PLC) is examined in this paper. PLC is a wired communication technology that provides communication and data transmission over the existing electrical network. It uses the electrical wiring in buildings or th...
A new universal front-end PFC rectifier topology of a battery charger for Electric Vehicles (EVs) is proposed, which allows fast charging at rated and/or full power level in case of 3-phase (Europe) as well as 1-phase (USA) mains supply. In this rega...
The imperative for EMC-optimized gate drivers in Gallium Nitride (GaN)-based automotive DC-DC converters stems from the stringent CISPR 25 standards and GaN’s intrinsic high-speed switching characteristics, which paradoxically exacerbate electr...
The large dv/dt and di/dt outputs of power devices in wireless charging system (WCS) in electric vehicles (EVs) always introduce conducted electromagnetic interference (EMI) emissions. This paper proposes a mitigation conducted emission strategy base...
Silicon carbide (SiC) power converters offer superior switching performance but generate severe broadband electromagnetic interference (EMI) that challenges regulatory compliance. Existing prediction methods face a fundamental trade-off between physi...
The large dv/dt and di/dt outputs of power devices in DC-fed motor drive systems in electric vehicles (EVs) always introduce conducted electromagnetic interference (EMI) emissions and may lead to motor drive system energy transmission losses. The eff...
The high dv/dt and di/dt outputs from power devices in a high-low voltage DC-DC converter on electric vehicles (EVs) can always introduce the unwanted conducted electromagnetic interference (EMI) emissions. A conducted EMI prediction and mitigation s...
Pearl millet (Pennisetum glaucum L.) is affected by drought stress, affecting crop productivity and survival. Long non-coding RNAs (lncRNAs) are reported to play a vital role in the response to drought stress. LncRNAs represent a major part of non-pr...