Skip to Content

Lubricants, Volume 10, Issue 6

2022 June - 26 articles

Cover Story: The present work reports the application of polyether amine derivatives as friction modifiers to improve the tribological properties of low viscosity poly-alpha-olefin. Three polyether amine derivatives with different molecular weights were synthesized, the tribological properties of which were systematically investigated under three different contact modes. The results exhibited that the molecular weights of the polymers had a direct effect on their tribological properties. The increase in molecular weight in a certain range was beneficial to the improvement of tribological performance, but further undue increase will rather reduce the friction reduction and wear resistance performances. View this paper
  • Issues are regarded as officially published after their release is announced to the table of contents alert mailing list .
  • You may sign up for email alerts to receive table of contents of newly released issues.
  • PDF is the official format for papers published in both, html and pdf forms. To view the papers in pdf format, click on the "PDF Full-text" link, and use the free Adobe Reader to open them.

Articles (26)

  • Article
  • Open Access
4 Citations
4,495 Views
15 Pages

Performance of a New Aeronautic Oil-Guiding Splash Lubrication System

  • Yu Dai,
  • Xi Chen,
  • Duan Yang,
  • Lanjin Xu and
  • Xiang Zhu

Among ever-increasing demands for low power consumption, low weight, and compact reducer systems, an oil-guiding splash lubrication method integrating the oil-guiding cylinder and pipes is suggested to be more suitable for light helicopters, instead...

(This article belongs to the Special Issue Gear Load-Independent Power Losses)
  • Review
  • Open Access
61 Citations
11,901 Views
37 Pages

The Twelve Principles of Green Tribology: Studies, Research, and Case Studies—A Brief Anthology

  • Marco Freschi,
  • Alessandro Paniz,
  • Elena Cerqueni,
  • Gianmarco Colella and
  • Giovanni Dotelli

Sustainability has become of paramount importance, as evidenced by the increasing number of norms and regulations concerning various sectors. Due to its intrinsic trans-sectorial nature, tribology has drawn the attention of the supporters of sustaina...

(This article belongs to the Special Issue Green Tribology: New Insights toward a Sustainable World 2023)
  • Article
  • Open Access
3 Citations
3,448 Views
15 Pages

Methyltrioctylammonium Octadecanoate as Lubricant Additive to Different Base Oils

  • Javier Faes,
  • Rubén González,
  • David Blanco,
  • Alfonso Fernández-González and ,
  • Antolin Hernández-Battez,
  • Patricia Iglesias and
  • José Luis Viesca
  • + 2 authors+ 0 author

This study investigates the use of an ionic liquid obtained from fatty acids (FAIL) as an additive at 2 wt.% in two different base oils: a mineral oil (M1) and a polyol ester (E1). Physicochemical characterization of the base oil–FAIL blends co...

(This article belongs to the Special Issue New Developments and Future Trends of Ionic Liquids as Lubricants)
  • Article
  • Open Access
2 Citations
2,721 Views
20 Pages

Unbalance Response Analysis of a Spindle Supported on Gas Bearings: A Comparison between Different Approaches

  • Federico Colombo,
  • Luigi Lentini,
  • Terenziano Raparelli,
  • Andrea Trivella and
  • Vladimir Viktorov

Gas journal bearings are widely employed in high-speed spindles for the micromachining industry. Compared to their oil and rolling counterparts, gas bearings have a longer life span, lower friction and a lower level of noise. In order to design accur...

(This article belongs to the Special Issue Tribology in Manufacturing and Design)
  • Article
  • Open Access
8 Citations
4,077 Views
15 Pages

Nanofluids based on vegetable oil have emerged as ecological alternatives to conventional cutting fluids. Jojoba-seed oil has recently been identified as adequate for use in metal cutting. Aiming to assess the stability and thermophysical properties...

  • Article
  • Open Access
19 Citations
4,177 Views
13 Pages

Friction and Wear Properties of a Nanoscale Ionic Liquid-like GO@SiO2 Hybrid as a Water-Based Lubricant Additive

  • Liang Hao,
  • Wendi Hao,
  • Peipei Li,
  • Guangming Liu and ,
  • Huaying Li,
  • Abdulrahman Aljabri and
  • Zhongliang Xie
  • + 2 authors+ 0 author

In this study, a nanoscale ionic liquid (NIL) GO@SiO2 hybrid was synthesized by attaching silica nanoparticles onto graphene oxide (GO). It was then functionalized to exhibit liquid-like behavior in the absence of solvents. The physical and chemical...

(This article belongs to the Special Issue Advances in Water-Based Nanolubricants)
  • Article
  • Open Access
19 Citations
5,236 Views
19 Pages

A wheel/rail friction coefficient that is too low can result in damage to the wheel and rail due to slips and slides, delays and safety concerns. A friction coefficient that is too high can result in excessive wear, noise and rolling contact fatigue....

  • Article
  • Open Access
14 Citations
4,640 Views
14 Pages

The grease film thickness was measured in fully flooded elastohydrodynamic lubrication, and the influence of rolling speed, load, consistency, base oil type and thickener type on grease film thickness was analyzed. A new calculation model for grease...

  • Article
  • Open Access
12 Citations
4,714 Views
8 Pages

The accuracy of five-axis machine tools is a key performance indicator. Among the various error sources of high precision five-axis machine tools, thermal and geometric errors occupy the majority. Thermal errors have become the largest error source o...

  • Article
  • Open Access
1 Citations
2,591 Views
12 Pages

Correlation of sharp contact problems is investigated with the focus on rigid-plastic contact behavior pertinent to engineering metals and alloys. The aim is to determine relations between the contact hardness and constitutive parameters suitable for...

  • Article
  • Open Access
5 Citations
3,348 Views
16 Pages

In the present work, Ni-10 wt.%TiO2 self-lubricating composite sinters were prepared via a powder metallurgy. Commercially available powder of nickel and non-commercial nanometric titanium dioxide (approx. 30 nm size) produced by the microwave method...

(This article belongs to the Special Issue Multiscale Tribology of Solid Lubricants)
  • Article
  • Open Access
12 Citations
4,485 Views
10 Pages

Development of a Cryogenic Tester with Air Bearing to Test Sliding-Rolling Contact Friction

  • Fengbo Liu,
  • Bing Su,
  • Guangtao Zhang,
  • Jiongli Ren and
  • Wenhu Zhang

This study aimed to test the friction coefficient of cryogenic bearing lubrication materials. A ball-on-disc type friction tester was developed in our lab using air bearings that could simulate the movement of cryogenic bearings under sliding-rolling...

  • Article
  • Open Access
12 Citations
5,559 Views
20 Pages

ZDDP Tribofilm Formation from a Formulated Oil on Textured Cylinder Liners

  • Leonardo C. Dias,
  • Giuseppe Pintaude,
  • Alessandro A. O. F. Vittorino and
  • Henara L. Costa

Surface texturing can improve lubrication and entrap wear debris but increases the effective roughness of the surfaces, which can induce higher contact pressures. On the one hand, this can be detrimental, but on the other hand, the increase in contac...

(This article belongs to the Special Issue Automotive Tribology II)
  • Article
  • Open Access
8 Citations
3,275 Views
9 Pages

The embedding situation between various nanoparticles and rough surfaces affects the lubrication characteristics of rolling bearings. If not properly handled, this can easily lead to wear damage of rolling bearings. Therefore, the friction and wear m...

(This article belongs to the Special Issue Friction and Lubrication of Sliding Bearings, Volume II)
  • Article
  • Open Access
6 Citations
6,442 Views
16 Pages

In this paper, a quasi-static angular contact ball bearing model, considering assembly accuracy is constructed, while a numerical solution method for bearing stiffness under bad assembly state is established. A 7014C angular contact ball bearing is u...

(This article belongs to the Special Issue Advances in Bearing Lubrication and Thermal Sciences)
  • Article
  • Open Access
19 Citations
4,154 Views
18 Pages

Research on Contact and Wear Characteristics of the Planetary Roller Screw Mechanism with Screw Misalignments

  • Junjie Meng,
  • Xing Du,
  • Xin Zhao,
  • Junwei Zheng and ,
  • Dingwei Wang and
  • Long Wan
  • + 1 author+ 0 author

Misalignments are unavoidable in most applications of the planetary roller screw mechanism (PRSM) due to many potential causes. However, the effect of screw misalignments on the contact characteristics for the PRSM have not been thoroughly investigat...

(This article belongs to the Special Issue Advances in Wear Predictive Models)
  • Article
  • Open Access
2 Citations
2,645 Views
12 Pages

This paper presents the results of the multi-aspect surface characterization of X39Cr13 steel samples subjected to technological processes specific to medical instrumentation, such as heat and thermochemical treatment, as well as sterilization, which...

(This article belongs to the Special Issue Surface Engineering for Wear Protection and Friction Reduction)
  • Article
  • Open Access
5 Citations
3,517 Views
17 Pages

In this study, we discussed the occurrence condition stick-slip model based on a 2DOF system, in which a 1DOF system model commonly used in stick-slip analysis was attached on an elastic foundation. Specifically, the effects of the mass, stiffness, a...

  • Article
  • Open Access
16 Citations
4,067 Views
16 Pages

Carbon Structures and Tribological Properties of Fe-C-SiC Self-Lubricating Metal Matrix Composites Prepared with α/β-SiC Polytypes

  • Guilherme Oliveira Neves,
  • Diego Berti Salvaro,
  • Tatiana Bendo,
  • Deise Rebelo Consoni and ,
  • José Daniel Biasoli de Mello,
  • Cristiano Binder and
  • Aloisio Nelmo Klein
  • + 2 authors+ 0 author

Sintered iron-based self-lubricant composites in which graphite reservoirs are generated by the dissociation of silicon carbide (SiC) particles feature low friction coefficients and scuffing resistance combined with high mechanical stress. This work...

(This article belongs to the Special Issue Friction and Wear in Composite Materials)
  • Article
  • Open Access
13 Citations
4,404 Views
17 Pages

Effects of an Electrical Double Layer and Tribo-Induced Electric Field on the Penetration and Lubrication of Water-Based Lubricants

  • Zhiqiang Luan,
  • Wenshuai Liu,
  • Yu Xia,
  • Ruochong Zhang and ,
  • Bohua Feng,
  • Xiaodong Hu,
  • Shuiquan Huang and
  • Xuefeng Xu
  • + 3 authors+ 0 author

Understanding the effects of electrical double layers (EDL) and tribo-induced electric fields on the electroosmotic behaviors of lubricants is important for developing high-performance water-based lubricants. In this study, EDL conductivities of aque...

(This article belongs to the Special Issue Advances in Water-Based Nanolubricants)
  • Article
  • Open Access
7 Citations
9,499 Views
20 Pages

This paper presents the optimization of the lubrication method of a helical bevel gearbox, which is part of a pickling line. The first gear stage of this gearbox showed frequent failures. The bevel gearing and bearings were damaged. Damage analysis w...

(This article belongs to the Special Issue Gear Load-Independent Power Losses)
  • Article
  • Open Access
15 Citations
3,105 Views
13 Pages

Friction and Wear Characteristics of Aqueous ZrO2/GO Hybrid Nanolubricants

  • Shuiquan Huang,
  • Zhen Wang,
  • Longhua Xu and
  • Chuanzhen Huang

Aqueous nanolubricants containing ZrO2 nanoparticles, graphene oxide (GO) nanosheets, or hybrid nanoparticles of ZrO2 and GO were formulated using a cost-effective ultrasonication de-agglomeration method. The friction and wear characteristics of thes...

(This article belongs to the Special Issue Advances in Water-Based Nanolubricants)
  • Perspective
  • Open Access
2 Citations
3,833 Views
4 Pages

Lubricant foaming and its mitigation is an active area of research driven by demands from modern machinery that require foam-free lubricant operation over extended periods and under adverse conditions. Tackling lubricant foaming has proven to be chal...

  • Article
  • Open Access
6 Citations
3,935 Views
18 Pages

Edge Pressures Obtained Using FEM and Half-Space: A Study of Truncated Contact Ellipses

  • Michael Juettner,
  • Marcel Bartz,
  • Stephan Tremmel,
  • Martin Correns and
  • Sandro Wartzack

In rolling or gear contacts, truncation of the contact ellipse can occur, for example, when an undercut extends into the contact area. For an elastic calculation approach, the edge constitutes a mathematical singularity, which is revealed by a theore...

  • Article
  • Open Access
3,056 Views
17 Pages

Development of Universal Friction Calibration Curve for Ball Ironing Test

  • Nuttakorn Sae-eaw,
  • Sutee Olarnrithinun,
  • Varunee Premanond and
  • Yingyot Aue-u-lan

The friction calibration curve (FCC) is normally constructed to indirectly approximate the friction value for any simulative friction test based on sensitive friction indicators (i.e., forming load or final geometry) by finite element modeling (FEM)....

(This article belongs to the Special Issue Advances in Wear Predictive Models)
  • Article
  • Open Access
14 Citations
5,895 Views
16 Pages

The requirements for the fuel economy of modern industry continue to drive the progress of low-viscosity lubricants. The present work reports the application of polyether amine derivatives as friction modifiers to improve the tribological properties...

XFacebookLinkedIn
Lubricants - ISSN 2075-4442