Skip to Content

20 Results Found

  • Article
  • Open Access
7 Citations
2,633 Views
18 Pages

13 May 2024

High-strength steel (HSS) members with welded sections exhibit a notably lower residual compressive stress ratio compared with common mild steel (CMS) members. Despite this difference, current codes often generalize the findings from CMS members to H...

(This article belongs to the Special Issue Experimental Study, Numerical Simulation & Structural Applications of Construction Materials—2nd Edition)
  • Article
  • Open Access
2 Citations
2,887 Views
22 Pages

This paper investigates the residual stresses induced by metal inert/active gas (MIG/MAG) welding in normal strength steel box sections, focusing on the validity of uniaxial residual stress assumption. Advanced manufacturing simulations are conducted...

  • Article
  • Open Access
5 Citations
2,395 Views
20 Pages

23 July 2020

BS700 high-strength steel is widely used in engineering. Welding residual stress during the manufacturing process has a significant influence on the structural safety and service life of steel structures. In this study, the residual stress of a BS700...

  • Article
  • Open Access
89 Views
30 Pages

Cyclic Behavior and Failure Modes of Q1100 Ultra-High-Strength Steel Box-Section Beam-Columns with Multiple Weld Repair Histories

  • Chengzhong Gui,
  • Lihao Chen,
  • Yanmin Zhang,
  • Yuxin Zhao and ,
  • Quanhao Dong and
  • Yuehang Zhang
  • + 1 author+ 0 author

7 November 2026

Welding repair is often unavoidable when steel structures in seismic regions are damaged, yet how it affects the cyclic performance of ultra-high-strength steel (UHSS) members is still not well understood. In this study, the hysteretic behaviour and...

(This article belongs to the Section Mechanics of Materials)
  • Article
  • Open Access
3 Citations
3,984 Views
26 Pages

29 February 2024

The local buckling behavior of welded square box section columns subjected to pure compression is investigated. Local buckling represents a crucial failure mode in thin-walled structures, exerting a significant impact on their overall stability and l...

(This article belongs to the Special Issue State-of-the-Art in Structural Steel Engineering)
  • Article
  • Open Access
1 Citations
2,076 Views
22 Pages

Overall Buckling Behavior and Design of Steel Stiffened Box Section Columns Under Axial Compression

  • Bing Shangguan,
  • Jie Li,
  • Qiu Zhao,
  • Peng Chen and ,
  • Furong Ruan and
  • Huiteng Pei
  • + 1 author+ 0 author

26 April 2025

This study experimentally and numerically investigated the overall buckling behavior of steel box column components. Two box section specimens were fabricated for axial compression tests. Prior to the tests, the material properties, initial geometric...

(This article belongs to the Special Issue Advanced Analysis and Design for Steel Structure Stability)
  • Article
  • Open Access
16 Citations
4,711 Views
15 Pages

26 April 2019

The orthotropic steel bridge deck weld structure would easily cause fatigue cracking under the repeated action of vehicle load. This paper took the steel box girder in a bridge as a research object, researched the mechanical properties of the steel p...

(This article belongs to the Special Issue Fracture, Fatigue and Structural Integrity of Metallic Materials)
  • Article
  • Open Access
159 Views
18 Pages

28 October 2026

Physical trial assembly (PTA) of large-scale welded steel structures under complex field conditions still relies on conventional measurement methods such as total stations, making it difficult to continuously capture the boundaries of assembly end-fa...

(This article belongs to the Section Construction Management, and Computers & Digitization)
  • Article
  • Open Access
6 Citations
2,162 Views
15 Pages

The Influence of Box-Strengthened Panel Zone on Steel Frame Seismic Performance

  • Linfeng Lu,
  • Jichen Zhang,
  • Gaowei Zhang,
  • Hao Peng and ,
  • Bingyou Liu and
  • Hanlin Hao
  • + 1 author+ 0 author

7 December 2023

During the Northridge earthquake, extensive brittle failures on the weld zones of the beam bottom flanges in the rigidity connection of steel special moment frames (SMFs) were detected. One of the primary reasons is the high-tensile strain demand cre...

(This article belongs to the Special Issue Research on the Seismic Design of Steel Frames)
  • Article
  • Open Access
6 Citations
3,426 Views
19 Pages

4 November 2024

The mast is a critical component of rotary drilling rigs, which has a cross-section consisting of a rectangular shape formed by two web plates and two flange plates. Structural optimization of the mast is necessary to address the issue of excessive w...

  • Article
  • Open Access
21 Citations
4,918 Views
11 Pages

29 July 2021

In this study, a method for detecting the railway surface defects called “squats” using the ABA (Axle Box Acceleration) measurement of trains was proposed. ABA prototype design, implementation, and field tests were conducted to derive and verify the...

(This article belongs to the Topic Advances on Structural Engineering)
  • Article
  • Open Access
91 Views
20 Pages

13 November 2026

Welding deformation in crane booms presents intractable challenges in manufacturing. An innovative simulation approach, based on the inherent strain method and pre-deformation method (ISM-PDM), is proposed to control welding deformation effectively i...

(This article belongs to the Section Welding and Joining)
  • Article
  • Open Access
10 Citations
4,062 Views
22 Pages

Hardox 450 Weld in Microstructural and Mechanical Approaches after Welding at Micro-Jet Cooling

  • Abílio P. Silva,
  • Tomasz Węgrzyn,
  • Tadeusz Szymczak,
  • Bożena Szczucka-Lasota and
  • Bogusław Łazarz

13 October 2022

The demand for high-strength steel welds, as observed in civil and transport engineering, is related to a mass reduction in vehicles. Container-type trucks are examples of this kind of transport means because their boxes are able to be produced using...

(This article belongs to the Topic Welding and Joining of Materials in Off-Shore and Energy Industry)
  • Article
  • Open Access
5 Citations
4,094 Views
15 Pages

Finite Element Analysis and Reinforcement of Steel Crane Beam under Eccentric Track Loading

  • Chunting Lu,
  • Zheng Yang,
  • Pengfei Li,
  • Xiangwei Zhang and ,
  • Jie Huang and
  • Ling Wang
  • + 1 author+ 0 author

7 September 2022

The crane track of a steel structure workshop was installed eccentrically, and the crane operation caused a large deflection of the crane beam, requiring reinforcement measures. The finite element model of the crane beam was established by Midas Gen...

(This article belongs to the Section Material Processing Technology)
  • Article
  • Open Access
6 Citations
3,489 Views
14 Pages

1 November 2023

A squat is a type of fatigue defect caused by short-wavelength rotational contact; if squats are detected early, the maintenance cost of the track can be effectively reduced. In this paper, a method for the early detection of squats is presented base...

(This article belongs to the Section Geotechnical, Geological and Environmental Engineering)
  • Article
  • Open Access
10 Citations
3,033 Views
18 Pages

2 October 2021

The steel constructions of mine shaft steelwork are particularly exposed to aggressive environments, which cause large, nonuniform corrosion loss throughout the steel members. A correct assessment of corrosion loss and load-carrying capacity of shaft...

(This article belongs to the Special Issue Research and Analysis in Structural Steels)
  • Article
  • Open Access
1,372 Views
18 Pages

19 December 2025

A weak-axis moment connection incorporating a double reduced beam section and a box-reinforced panel zone (WDRBS) is introduced for hot-rolled H-shaped columns. The configuration is intended to shift inelastic demand away from the column face and to...

(This article belongs to the Special Issue Seismic and Durability Performance of Steel Connections)
  • Article
  • Open Access
12 Citations
15,912 Views
25 Pages

28 June 2020

In modern steel construction, thin-walled elements with Class 4 cross-sections are commonly used. For the sake of the computation of such elements according to European Eurocode 3 (EC3), simplified computational models are applied. These models do no...

(This article belongs to the Special Issue Architectural Structure)
  • Article
  • Open Access
11 Citations
4,281 Views
12 Pages

Experimental Assessment of Time-Limited Operation and Rectification of a Bridge Crane

  • Peter Frankovský,
  • Ingrid Delyová,
  • Peter Sivák,
  • Piotr Kurylo and ,
  • Elena Pivarčiová and
  • Vojtech Neumann
  • + 1 author+ 0 author

14 June 2020

This paper describes a problem related to a casting bridge crane with a combined load of 200/50/12.5 t and a span of 18.6 m, working in a heavy metallurgical operation. Due to the specific stress of the structure after its long-term operation, longit...

(This article belongs to the Special Issue Machine Design: Numerical Simulation and Experimental Tests of Engineering Materials and Devices)
  • Article
  • Open Access
2,207 Views
20 Pages

Perforated and Composite Beam and Arch Design Optimization during Asymmetric Post-Buckling Deformation

  • Igor Andrianov,
  • Viktor Olevskyi,
  • Oleksandr Olevskyi and
  • Yuliia Olevska

15 August 2024

The structural elements of buildings have recently required the development of efficient design solutions due to increased dynamic and thermal loads. The main solution for improving the efficiency of such elements involves creating lightweight non-un...

(This article belongs to the Section C: Physics)