The hot deformation test of the nano silicon carbide (nano-SiC) and carbon nano tubes (CNT) hybrid-reinforced AZ80 matrix composite was performed at compression temperatures of 300–450 °C and strain rates of 0.0001–1 s−1. It cou...
Hot deformation behavior and microstructure evolution of 2707 hyper duplex stainless steel (HDSS) were investigated through hot compression tests in the temperature range of 900–1250 °C and strain rate range of 0.01–10 s−1. The results showed that th...
In this study, we investigated the hot deformation behavior and microstructural evolution of a novel high-magnesium-content (high-Mg) aluminum alloy, bridging the disciplines of material processing and physical metallurgy. Uniaxial hot compression te...
The effects of temperature, strain rate, and strain on the microstructure, texture, and mechanical properties of as-extruded nanodiamond reinforced ZK60 composite during hot compression was systematically studied. The results revealed that the precip...
The high-temperature thermal deformation behavior of a 2205/Q345 specimen at 850–1100 °C and strain rate of 0.01–10 s−1 was systematically studied by the Gleeble-3800 thermal simulator, which provided a theoretical basis for the...
In this study, pure copper’s hot deformation behavior was studied through isothermal compression tests at deformation temperatures of 350~750 °C with strain rates of 0.01~5 s−1 on a Gleeble-3500 isothermal simulator. Metallographic ob...
In order to study the microstructure evolution and flow stress behavior of as cast antibacterial austenitic stainless steel containing 1.52 wt.% copper, Gleeble 3800 was used for thermal compression simulation test. Through OM and EBSD analysis, it i...
Mg-Gd-Y-Zn-Zr Mg alloys show excellent performance in high-end manufacturing due to its strength, hardness and corrosion resistance. However, the hot deformation and dynamic recrystallization (DRX) behaviors of Mg-13.5Gd-3.2Y-2.3Zn-0.5Zr were not stu...
20Mn5 steel is widely used in the manufacture of heavy hydro-generator shaft forging due to its strength, toughness, and wear resistance. However, the hot deformation and recrystallization behaviors of 20Mn5 steel compressed under a high temperature...
The effect of high-temperature deformation twinning on the work hardening behaviors of Fe-38Mn alloy during hot shear-compression deformation was investigated. The discovery of micro-shear bands and deformation twinning is significant for continuous...
The hot deformation behavior of T15MN high-speed steel during thermal compression was studied by experiment and simulation. Specifically, the hot compression test was carried out on a Gleeble-1500 thermal-mechanical simulator at temperatures from 127...
Hot deformation behavior and the microstructural evolution of Inconel 625 superalloy plates are investigated by hot compression tests in a range of working temperatures (800–1050 °C) and strain rates (0.001–1 s−1). The microstructural observation sho...
To understand the effect of the initial state of AA2195 Al-Li alloy on the forming process, as-cast and homogenized ingots were compressed by using a Gleeble-3150 thermo-mechanical simulator at different temperatures (360–480 °C) and strain...
GH2132, an Ni–Cr–Fe-based superalloy for aero-engine components, exhibits hot workability that is highly sensitive to processing parameters. The hot deformation behavior of GH2132 alloy was investigated via isothermal compression (Gleeble...
The effect of trace Bi impurities on the flow stress, microstructure evolution, and dynamic recrystallization (DRX) of the ultrahigh-purity copper was systematically investigated by a hot compression test at 600 °C. The results show that the peak...
The deformation behavior of homogenized Al–7.5Zn–1.5Mg–0.2Cu–0.2Zr alloy has been studied by a set of isothermal hot compression tests, which were carried out over the temperature ranging from 350 °C to 450 °C and the strain rate ranging from 0.001 s...
This study investigated the thermal compression deformability of the low-alloyed Mg-Zn-Y-Zr magnesium alloy temperatures ranging from 300 to 450 °C, and strain rates between 0.01 s−1 and 1 s−1. A hot processing map was established usi...
The Cu-1.7Ni-1.4Co-0.65Si (wt%) alloy is hot compressed by a Gleeble-1500D machine under a temperature range of 760 to 970 °C and a strain rate range of 0.01 to 10 s−1. The flow stress increases with the extension of strain rate and decreas...
Borated stainless steel (BSS) specimens have a boron content of 1.86 wt%, and are prepared by hot isostatic pressing (HIP) conducted at different temperatures, ranging from 1000 to 1100 °C and a constant true strain rate (0.01, 0.1, 1 and 10 s&mi...
The hot deformation behaviors of the SJTU-1 alloy, the high-throughput scanned casting Nickel-based superalloy, was investigated by compression test in the temperature range of 900 to 1200 °C and strain rate range of 0.1–0.001 s−1. The hot processing...
Deformation behavior of pure iridium has been studied during thermal compression testing with the help of Gleeble-1500D in the temperature range of 1200 °C~1500 °C and strain rate range of 10−1 s−1~10−2 s−1. Resistance...
Solid state sintering of cast aluminum powders by resistance heating sintering (RHS), also known as spark plasma sintering or field-assisted sintering technique, creates a very fine microstructure in the bulk material. This leads to high performance...
Cu–9Ni–6Sn alloys have received widespread attention due to their good mechanical properties and resistance to stress relaxation in the electronic and electrical industries. The hot compression deformation behaviors of the Cu–9Ni&nd...
In this review paper, the hot compressive deformation mechanisms and processing maps of high-entropy alloys (HEAs) with different chemical compositions and crystal structures are analyzed. The stress exponent (n1) values measured from the series of c...
Nowadays, wrought zinc-based biodegradable alloys are favored by researchers, due to their excellent mechanical properties and suitable degradation rates. However, there are few research studies on their thermal deformation behavior at present. This...
Aiming to investigate the role and mechanism of nano MgO on the hot compressive deformation behavior of Mg alloys, the Mg-3Zn-0.2Ca alloy (MZC, in wt%) and the 0.2MgO/Mg-3Zn-0.2Ca alloy (MZCM, in wt%) were investigated systematically in the temperatu...
The hot deformation behavior and microstructural evolution of an Al-Zn-Mg-Cu (7150) alloy was studied during hot compression at various temperatures (300 to 450 °C) and strain rates (0.001 to 10 s−1). A decline ratio map of flow stresses was proposed...
In order to predict hot deformation behavior of superalloy nimonic 80A, a back-propagational artificial neural network (BP-ANN) and strain-dependent Arrhenius-type model were established based on the experimental data from isothermal compression test...
High-temperature compression tests on Mg-11.5Li-2.5Zn-0.35Al-0.3Y (in wt.%) were carried out on a Gleeble-3500 thermal simulator. Flow stress and microstructural evolution were analyzed at different temperatures (T = 473 K, 523 K, 573 K, and 623 K) a...
The 2198 Al–Li alloy has unique superiority in mechanical performance and has been extensively used in the aerospace field. In this study, the hot deformation behavior of the 2198 Al–Li alloy was investigated on a Gleeble-1500 thermomecha...
In this work, composites based on AA5049 aluminium alloy reinforced with multiwalled carbon nanotubes (CNTs) and multiwalled TiC-coated CNTs were prepared by powder metallurgy. For the first time, the effect of TiC coating on the CNT surface on the f...
The flow behavior and the microstructural evolution of aluminum alloy 7055 in two heat treatment conditions (homogenized vs. pre-rolled, solution treated, stretched and naturally aged (T3)) were investigated for a height reduction of 60% with deforma...
The isothermal compression tests of the nickel-based superalloy Waspaloy were carried out under various temperatures from 1040 to 1120 °C and strain rates from 0.01 to 10 s−1 with the height reduction of 60% and the flow stress curves were...
In order to verify the correctness of the transition of deformation mechanism with the change in deformation parameters and to reveal the types and mechanism of dynamic recrystallization of γ grains during compression deformation, microstructur...
The formation and evolution of shear bands in Inconel 718 nickel-base superalloy under plane strain compression was investigated in the present work. It is found that the propagation of shear bands under plane strain compression is more intense in co...
In this study, the hot deformation activation energy values of 7050-T7451 aluminum alloy, calculated with two different methods under three deformation modes, were compared. The results showed that the hot deformation activation energy values obtaine...
The hot compression simulation testing machine was utilized to conduct compression experiments on an Al-Mg-Si-Mn alloy containing the rare earth element Sc at a deformation temperature ranging from 450 to 550 °C and a strain rate of 0.01 to 10 s&...
In this paper, the VPSC (visco-plastic self-consistent) model was improved by considering the effect of heating rate. The hot compression deformation behavior and texture evolution of AA7075 were studied based on the improved VPSC model and EBSD (ele...
The deformation mechanism during the hot compression of PM nickel-based superalloy FGH99 and its micro-structural evolution, especially the evolution of γ’ phases, are the key factors affecting the final molding quality of aero-engine hot...
The Gleeble-1500 hot simulation experimental equipment was used to investigate the effects of hot simulation compression on PH13-8Mo stainless steel with strain rates ranging from 0.1 to 10 s−1 and deformation temperatures ranging from 900 to 1...
The hot deformation behavior of a harmonic-structured pure nickel has been studied and compared with the hot deformability of a homogeneously structured nickel. Both materials were produced via the powder metallurgy route through the Spark Plasma Sin...
Warm deformation is a plastic-forming process that differs from traditional cold and hot forming techniques. At the macro level, it can effectively reduce the problem of high deformation resistance in cold deformation and improve the surface decarbur...
The hot deformation behavior of the GY200 Ni-based alloys with different tungsten (W) content were investigated by means of hot compression tests, microscopic observations, and processing maps at temperatures between 950 °C and 1200 °C, strai...
The hot deformation behavior of an Al-Zn-Mg-Cu alloy was investigated by hot compression test at deformation temperatures varying from 320 to 440 °C with strain rates ranging from 0.01 to 10 s−1. The results show that the Mg(Zn, Cu)2 particles as a r...
A hot compression test of new Al-6Mg and Al-8Mg alloys was conducted to understand the dynamic recrystallization (DRX) behavior by Mg contents. To investigate the hot workability of Al-Mg with high Mg contents, the hot deformation behavior of Al-6Mg...
In this study, hot compression experiments were conducted on cast TC21 titanium alloy using a Gleeble-1500D thermal simulation compression tester, and the hot-compressed specimens were heat-treated. The data obtained after analyzing the thermal compr...
The development of new materials with low weight for the transport industry is required for the saving of natural resources and protection of the environment from carbon dioxide pollution. The microstructure and mechanical properties of the Fe-30Mn-1...
The hot deformation behavior of a newly designed Fe–5Mn–3Al–0.1C (wt.%) medium manganese steel was investigated using hot compression tests in the temperature range of 900 to 1150 °C, at constant strain rates of 0.1, 1, 2.5, 5, 10, and 20 s−1. A deta...
The deteriorated plasticity arising from the insoluble precipitates may lead to cracks during the rolling of FeCrAl alloys. The microstructure evolution and hot deformation behavior of an FeCrAl alloy were investigated in the temperature range of 750...
The hot deformation behavior of a new Al–Mn–Sc alloy was investigated by hot compression conducted at temperatures from 330 to 490 °C and strain rates from 0.01 to 10 s−1. The hot deformation behavior and microstructure of the a...
of 10