The synthesis–composition–structure relationship in the Mg–Ca–Al system is studied using combinatorial magnetron sputtering. With increasing deposition temperature, a drastic decrease in Mg concentration is obtained. This beha...
High-throughput methods are extremely important in today’s materials science, especially in the case of thin film characterization. The micro-combinatorial method enables the deposition and characterization of entire multicomponent thin film sy...
We performed an electrochromic investigation to optimize the composition of reactive magnetron-sputtered mixed layers of zinc oxide and tin oxide (ZnO-SnO2). Deposition experiments were conducted as a combinatorial material synthesis approach. The bi...
Thin films of mixed MoO3 and WO3 were obtained using reactive magnetron sputtering onto ITO-covered glass, and the optimal composition was determined for the best electrochromic (EC) properties. A combinatorial material synthesis approach was applied...
A combinatorial Co-Cr-Fe-Ni compositional complex alloy (CCA) thin film disk with a thickness of 1 µm and a diameter of 10 cm was processed by multiple-beam-sputtering physical vapor deposition (PVD) using four pure metal sources. The chemical...
Combinatorial magnetron sputtering and electrical characterization were used to systematically study the impact of compositional changes in the resistive switching of transition metal oxides, specifically the ZrxTa1−xOy system. Current-voltage...
Nitrides of aluminum (Al) and titanium (Ti) mixtures have long been studied and used as commercial coatings because of their high hardness and high oxidation resistance due to the formation of an alumina layer on the coating surface. To fully underst...
Intermetallic Al-Si-based coatings can greatly increase the oxidation resistance of γ-TiAl alloys. However, the effects of the Si addition are not fully understood. Therefore, it is difficult to determine the Si content that is optimal for oxid...
We synthesized a combinatorial library of CuxNi1−x alloy thin films via co-sputtering from Cu and Ni targets to catalyze graphene chemical vapor deposition. The alloy morphology, composition, and microstructure were characterized via scanning e...
Gradient a-Si1−xGex layers have been deposited by ”one-sample concept” combinatorial direct current (DC) magnetron sputtering onto one-inch-long Si slabs. Characterizations by electron microscopy, ion beam analysis and ellipsometry show that the laye...
Al-Cu thin films were fabricated by RF magnetron sputtering from aluminum (Al) and copper (Cu) metal targets to improve the acoustic performance of SAW devices on LiNbO3 substrates. To optimize the electrode material for SAW devices, Al-Cu films with...
The novel, single-sample concept combinatorial method, the so-called micro-combinatory technique, has been shown to be suitable for the high-throughput and complex characterization of multicomponent thin films over an entire composition range. This r...
The synthesis of nanoparticles by combinatorial sputtering in ionic liquids is a versatile approach for discovering new materials. Whereas the influence on nanoparticle formation of different pure ionic liquids has been addressed, the influence of (I...
Numerous technological advancements in the 21st century depend on the creation of novel materials possessing enhanced properties; there is a growing reliance on materials that can be optimized to serve multiple functions. To efficiently save time and...
A ternary Cr2AlB2 phase was deposited as a film using magnetron sputtering. Its anisotropic structure displays both structural and chemical similarities with the nanolaminated MAX phases (Mn+1AXn (n = 1–3) where M usually is an early transition...
A novel artificial intelligence-assisted evaluation of the X-ray diffraction (XRD) peak profiles was elaborated for the characterization of the nanocrystallite microstructure in a combinatorial Co-Cr-Fe-Ni compositionally complex alloy (CCA) film. Th...
Ruthenium (Ru) and its alloys exhibit high corrosion resistance in acidic environments; however, their corrosion behavior in supercritical acidic fluids remains unclear. In this study, the corrosion resistance of Ru–Mo–W and Ru–Mo&n...
Ta–B–C coatings were non-reactively sputter-deposited in an industrial batch coater from a single segmented rotating cylindrical cathode employing a combinatorial approach. The chemical composition, morphology, microstructure, mechanical...
A nanocrystalline Co-Cr-Ni-Fe compositional complex alloy (CCA) film with a thickness of about 1 micron was produced by a multiple-beam-sputtering physical vapor deposition (PVD) technique. The main advantage of this novel method is that it does not...
A broad compositional range of Nb-Ti anodic memristors with volatile and self-rectifying behaviour was studied using a combinatorial screening approach. A Nb-Ti thin-film combinatorial library was co-deposited by sputtering, serving as the bottom ele...
Multiple principal element alloys, also often referred to as compositionally complex alloys or high entropy alloys, present extreme challenges to characterize. They show a vast, multidimensional composition space that merits detailed investigation an...
This Special Issue was devoted to developments made in Physical Vapour Deposited (PVD) biomedical coatings for various healthcare applications. The scrutinized PVD methods were Radio-Frequency Magnetron Sputtering (RF-MS), Cathodic Arc Evaporation, P...
Combinatorial deposition, comprising filtered cathodic vacuum arc (FCVA) and physical vapor deposition (PVD) magnetron sputtering is employed to deposit molybdenum disulphide (MoS2) and titanium (Ti) thin films onto TiB2-coated tool inserts specifica...
We used high-power impulse magnetron sputtering (HiPIMS) to deposit tungsten carbide films for superior wear protection in abrasive environments. In order to sample different W-to-C ratios more efficiently, a combinatorial approach was chosen. A sing...
The development of novel materials with coexisting volatile threshold and non-volatile memristive switching is crucial for neuromorphic applications. Hence, the aim of this work was to investigate the memristive properties of oxides in a Hf–Nb...
A combinatorial material adhesion study was used to optimize the composition of an adhesion promoting layer for a nanocrystalline diamond (NCD) coating on silicon. Three different adhesion promoting metals, namely W, Cr, and Ta, were selected to fabr...
To realize highly sensitive SAW devices, novel Al–Cu thin films were developed using a combinatorial sputtering system. The Al–Cu sample library exhibited a wide range of chemical compositions and electrical resistivities, providing valua...
Cu2ZnSnS4 (CZTS) is an economically and environmentally friendly alternative to other toxic and expensive materials used for photovoltaics, however, the variation in the composition during synthesis is often followed by the occurrence of the secondar...