Nanomaterials

Article

18 pages, 4045 KiB

Open AccessEditor’s ChoiceArticle

Electrochemical Synthesis, Magnetic and Optical Characterisation of FePd Dense and Mesoporous Nanowires

by Deepti Raj, Gabriele Barrera, Federico Scaglione, Federica Celegato, Matteo Cialone, Marco Coïsson, Paola Tiberto, Jordi Sort, Paola Rizzi and Eva Pellicer

Nanomaterials 2023, 13(3), 403; https://doi.org/10.3390/nano13030403 - 19 Jan 2023

Cited by 1 | Viewed by 2466

Abstract

Dense and mesoporous FePd nanowires (NWs) with 45 to 60 at.% Pd content were successfully fabricated by template- and micelle-assisted pulsed potentiostatic electrodeposition using nanoporous anodic alumina and polycarbonate templates of varying pore sizes. An FePd electrolyte was utilized for obtaining dense NWs [...] Read more.

Dense and mesoporous FePd nanowires (NWs) with 45 to 60 at.% Pd content were successfully fabricated by template- and micelle-assisted pulsed potentiostatic electrodeposition using nanoporous anodic alumina and polycarbonate templates of varying pore sizes. An FePd electrolyte was utilized for obtaining dense NWs while a block copolymer, P-123, was added to this electrolyte as the micelle-forming surfactant to produce mesoporous NWs. The structural and magnetic properties of the NWs were investigated by electron microscopy, X-ray diffraction, and vibrating sample magnetometry. The as-prepared NWs were single phase with a face-centered cubic structure exhibiting 3.1 µm to 7.1 µm of length. Mesoporous NWs revealed a core-shell structure where the porosity was only witnessed in the internal volume of the NW while the outer surface remained non-porous. Magnetic measurements revealed that the samples displayed a soft ferromagnetic behavior that depended on the shape anisotropy and the interwire dipolar interactions. The mesoporous core and dense shell structure of the NWs were seen to be slightly affecting the magnetic properties. Moreover, mesoporous NWs performed excellently as SERS substrates for the detection of 4,4′-bipyridine, showing a low detection limit of 10⁻¹² M. The signal enhancement can be attributed to the mesoporous morphology as well as the close proximity of the embedded NWs being conducive to localized surface plasmon resonance. Full article

(This article belongs to the Special Issue New Challenges in Nanofilm and Nanowire Characterization)

► Show Figures

Figure 1

14 pages, 2218 KiB

Open AccessEditor’s ChoiceArticle

Magnetic Properties of Zig-Zag-Edged Hexagonal Nanohelicenes: A Quantum Chemical Study

by Vitaly Porsev and Robert Evarestov

Nanomaterials 2023, 13(3), 415; https://doi.org/10.3390/nano13030415 - 19 Jan 2023

Cited by 7 | Viewed by 1545

Abstract

The atomic structure and electronic and magnetic properties of two zig-zag-edged hexagonal nanohelicenes of the second type [1.2] and [2.2] were studied by the density functional theory. These objects possess a helical periodicity and belong to the fifth family of line symmetry groups [...] Read more.

The atomic structure and electronic and magnetic properties of two zig-zag-edged hexagonal nanohelicenes of the second type [1.2] and [2.2] were studied by the density functional theory. These objects possess a helical periodicity and belong to the fifth family of line symmetry groups in their global energy minimum. These nanohelicenes were shown by us to be diamagnetic metals that undergo spontaneous symmetry breaking into antiferromagnetic semiconductors as a result of the Mott–Hubbard metal-insulator transition. However, under some torsional stress, a reversible transformation to a diamagnetic metal can take place, which is promising for the use of nanohelicenes in electro-magneto-mechanical nanodevices. Full article

(This article belongs to the Section Theory and Simulation of Nanostructures)

► Show Figures

Figure 1

11 pages, 2416 KiB

Open AccessEditor’s ChoiceArticle

Pixelated Micropolarizer Array Based on Carbon Nanotube Films

by Hui Zhang, Yanji Yi, Yibin Wang, Huwang Hou, Ting Meng, Peng Zhang and Yang Zhao

Nanomaterials 2023, 13(3), 391; https://doi.org/10.3390/nano13030391 - 18 Jan 2023

Viewed by 1314

Abstract

A micropolarizer array (MPA) that can be integrated into a scientific camera is proposed as a real-time polarimeter that is capable of extracting the polarization parameters. The MPA is based on highly aligned carbon nanotube (CNT) films inspired by their typical anisotropy and [...] Read more.

A micropolarizer array (MPA) that can be integrated into a scientific camera is proposed as a real-time polarimeter that is capable of extracting the polarization parameters. The MPA is based on highly aligned carbon nanotube (CNT) films inspired by their typical anisotropy and selectivity for light propagation over a wide spectral range. The MPA contains a dual-tier CNT pixel plane with 0° and 45° orientations. The thickness of the dual-tier structure of the CNT-based MPA is limited to less than 2 μm with a pixel size of 7.45 μm × 7.45 μm. The degree of polarization of the CNT-MPA reached 93% at a 632 nm wavelength. The specific designs in structure and semiconductor fabrication procedures are described. Compared with customary MPAs, CNT-based MPA holds great potential in decreasing the cross-talk risk associated with lower film thickness and can be extended to a wide spectral range. Full article

(This article belongs to the Special Issue 2D Materials for Advanced Sensors: Fabrication and Applications)

► Show Figures

Figure 1

16 pages, 4936 KiB

Open AccessEditor’s ChoiceArticle

Graphene-Based Coating to Mitigate Biofilm Development in Marine Environments

by Francisca Sousa-Cardoso, Rita Teixeira-Santos, Ana Francisca Campos, Marta Lima, Luciana C. Gomes, Olívia S. G. P. Soares and Filipe J. Mergulhão

Nanomaterials 2023, 13(3), 381; https://doi.org/10.3390/nano13030381 - 18 Jan 2023

Cited by 8 | Viewed by 3064

Abstract

Due to its several economic and ecological consequences, biofouling is a widely recognized concern in the marine sector. The search for non-biocide-release antifouling coatings has been on the rise, with carbon-nanocoated surfaces showing promising activity. This work aimed to study the impact of [...] Read more.

Due to its several economic and ecological consequences, biofouling is a widely recognized concern in the marine sector. The search for non-biocide-release antifouling coatings has been on the rise, with carbon-nanocoated surfaces showing promising activity. This work aimed to study the impact of pristine graphene nanoplatelets (GNP) on biofilm development through the representative marine bacteria Cobetia marina and to investigate the antibacterial mechanisms of action of this material. For this purpose, a flow cytometric analysis was performed and a GNP/polydimethylsiloxane (PDMS) surface containing 5 wt% GNP (G5/PDMS) was produced, characterized, and assessed regarding its biofilm mitigation potential over 42 days in controlled hydrodynamic conditions that mimic marine environments. Flow cytometry revealed membrane damage, greater metabolic activity, and endogenous reactive oxygen species (ROS) production by C. marina when exposed to GNP 5% (w/v) for 24 h. In addition, C. marina biofilms formed on G5/PDMS showed consistently lower cell count and thickness (up to 43% reductions) than PDMS. Biofilm architecture analysis indicated that mature biofilms developed on the graphene-based surface had fewer empty spaces (34% reduction) and reduced biovolume (25% reduction) compared to PDMS. Overall, the GNP-based surface inhibited C. marina biofilm development, showing promising potential as a marine antifouling coating. Full article

(This article belongs to the Special Issue Nano-Enhanced Strategies for Biofouling and Biocorrosion Prevention)

► Show Figures

Graphical abstract

13 pages, 2679 KiB

Open AccessEditor’s ChoiceArticle

Numerical and Experimental Study of Colored Magnetic Particle Mapping via Magnetoelectric Sensors

by Ron-Marco Friedrich, Mohammad Sadeghi and Franz Faupel

Nanomaterials 2023, 13(2), 347; https://doi.org/10.3390/nano13020347 - 14 Jan 2023

Cited by 3 | Viewed by 2037

Abstract

Colored imaging of magnetic nanoparticles (MNP) is a promising noninvasive method for medical applications such as therapy and diagnosis. This study investigates the capability of the magnetoelectric sensor and projected gradient descent (PGD) algorithm for colored particle detection. In the first step, the [...] Read more.

Colored imaging of magnetic nanoparticles (MNP) is a promising noninvasive method for medical applications such as therapy and diagnosis. This study investigates the capability of the magnetoelectric sensor and projected gradient descent (PGD) algorithm for colored particle detection. In the first step, the required circumstances for image reconstruction are studied via a simulation approach for different signal-to-noise ratios (SNR). The spatial accuracy of the reconstructed image is evaluated based on the correlation coefficient (CC) factor. The inverse problem is solved using the PGD method, which is adapted according to a nonnegativity constraint in the complex domain. The MNP characterizations are assessed through a magnetic particle spectrometer (MPS) for different types. In the experimental investigation, the real and imaginary parts of the MNP’s response are used to detect the spatial distribution and particle type, respectively. The experimental results indicate that the average phase difference for CT100 and ARA100 particles is 14 degrees, which is consistent with the MPS results and could satisfy the system requirements for colored imaging. The experimental evaluation showed that the magnetoelectric sensor and the proposed approach could be potential candidates for color bio-imaging applications. Full article

(This article belongs to the Special Issue Perspectives in Magnetoelectric and Magnetic Nanomaterials)

► Show Figures

Figure 1

10 pages, 2258 KiB

Open AccessEditor’s ChoiceArticle

Synthesis of Nanocrystalline PuO₂ by Hydrothermal and Thermal Decomposition of Pu(IV) Oxalate: A Comparative Study

by Viktoria Baumann, Karin Popa, Olaf Walter, Murielle Rivenet, Gérald Senentz, Bertrand Morel and Rudy J.M. Konings

Nanomaterials 2023, 13(2), 340; https://doi.org/10.3390/nano13020340 - 13 Jan 2023

Cited by 4 | Viewed by 8057

Abstract

In recent years, the hydrothermal conversion of actinide (IV) oxalates into nanometric actinide dioxides (AnO₂) has begun to be investigated as an alternative to the widely implemented thermal decomposition method. We present here a comparison between the hydrothermal and [...] Read more.

In recent years, the hydrothermal conversion of actinide (IV) oxalates into nanometric actinide dioxides (AnO₂) has begun to be investigated as an alternative to the widely implemented thermal decomposition method. We present here a comparison between the hydrothermal and the conventional thermal decomposition of Pu(IV) oxalate in terms of particle size, morphology and residual carbon content. A parametric study was carried out in order to define the temperature and time applied in the hydrothermal conversion of tetravalent Pu-oxalate into PuO₂ and to optimize the reaction conditions. Full article

► Show Figures

Figure 1

8 pages, 2345 KiB

Open AccessEditor’s ChoiceCommunication

High-Performance n-Type Bi₂Te₃ Thermoelectric Fibers with Oriented Crystal Nanosheets

by Min Sun, Pengyu Zhang, Guowu Tang, Dongdan Chen, Qi Qian and Zhongmin Yang

Nanomaterials 2023, 13(2), 326; https://doi.org/10.3390/nano13020326 - 12 Jan 2023

Cited by 6 | Viewed by 1915

Abstract

High-performance thermoelectric fibers with n-type bismuth telluride (Bi₂Te₃) core were prepared by thermal drawing. The nanosheet microstructures of the Bi₂Te₃ core were tailored by the whole annealing and Bridgman annealing processes, respectively. The influence of the [...] Read more.

High-performance thermoelectric fibers with n-type bismuth telluride (Bi₂Te₃) core were prepared by thermal drawing. The nanosheet microstructures of the Bi₂Te₃ core were tailored by the whole annealing and Bridgman annealing processes, respectively. The influence of the annealing processes on the microstructure and thermoelectric performance was investigated. As a result of the enhanced crystalline orientation of Bi₂Te₃ core caused by the above two kinds of annealing processes, both the electrical conductivity and thermal conductivity could be improved. Hence, the thermoelectric performance was enhanced, that is, the optimized dimensionless figure of merit (ZT) after the Bridgman annealing processes increased from 0.48 to about 1 at room temperature. Full article

(This article belongs to the Special Issue Advanced Nanoscale Materials for Thermoelectric Applications)

► Show Figures

Figure 1

14 pages, 5939 KiB

Open AccessEditor’s ChoiceArticle

The Local and Electronic Structure Study of Lu_xGd_1−xVO₄ (0 ≤ x ≤ 1) Solid Solution Nanocrystals

by Yang Chen, Ziqing Li, Nianjing Ji, Chenxi Wei, Xiulan Duan and Huaidong Jiang

Nanomaterials 2023, 13(2), 323; https://doi.org/10.3390/nano13020323 - 12 Jan 2023

Viewed by 1792

Abstract

Rare-earth-doped mixed crystals have demonstrated tunable optical properties, and it is of great importance to study the structural characteristics of the mixed-crystal hosts. Herein, Lu_xGd_1-xVO₄ (0 ≤ x ≤ 1) solid solution nanocrystals were synthesized by a [...] Read more.

Rare-earth-doped mixed crystals have demonstrated tunable optical properties, and it is of great importance to study the structural characteristics of the mixed-crystal hosts. Herein, Lu_xGd_1-xVO₄ (0 ≤ x ≤ 1) solid solution nanocrystals were synthesized by a modified sol–gel method, with a pure crystalline phase and element composition. The X-ray diffraction (XRD) and Rietveld refinement results showed that Lu_xGd_1−xVO₄ nanocrystals are continuous solid solutions with a tetragonal zircon phase (space group I4₁/amd) and the lattice parameters strictly follow Vegard’s law. The detailed local structures were studied by extended X-ray absorption fine structure (EXAFS) spectra, which revealed that the average bond length of Gd-O fluctuates and decreases, while the average bond length of Lu-O gradually decreases with the increase in Lu content. Furthermore, the binding energy differences of core levels indicate that the covalent V-O bond is relatively stable, while the ionicity of the Lu-O bond decreases with the increasing x value, and the ionicity of the Gd-O bond fluctuates with small amplitude. The valence band structures were further confirmed by the first-principles calculations, indicating that the valence band is contributed to by the O 2p nonbonding state, localized Gd 4f and Lu 4f states, and the hybridized states between the bonding O 2p and V 3d. The binding energies of the Lu core and the valence levels tend to decrease gradually with the increase in Lu content. This work provides insight into the structural features of mixed-crystal hosts, which have been developed in recent years to improve laser performance by providing different positions for active ions to obtain inhomogeneous broadening spectra. Full article

(This article belongs to the Special Issue Optoelectronic Functional Nanomaterials and Devices)

► Show Figures

Figure 1

13 pages, 2584 KiB

Open AccessEditor’s ChoiceArticle

Rational Optimization of Cathode Composites for Sulfide-Based All-Solid-State Batteries

by Artur Tron, Raad Hamid, Ningxin Zhang and Alexander Beutl

Nanomaterials 2023, 13(2), 327; https://doi.org/10.3390/nano13020327 - 12 Jan 2023

Cited by 7 | Viewed by 4370

Abstract

All-solid-state lithium-ion batteries with argyrodite solid electrolytes have been developed to attain high conductivities of 10⁻³ S cm⁻¹ in studies aiming at fast ionic conductivity of electrolytes. However, no matter how high the ionic conductivity of the electrolyte, the design of [...] Read more.

All-solid-state lithium-ion batteries with argyrodite solid electrolytes have been developed to attain high conductivities of 10⁻³ S cm⁻¹ in studies aiming at fast ionic conductivity of electrolytes. However, no matter how high the ionic conductivity of the electrolyte, the design of the cathode composite is often the bottleneck for high performance. Thus, optimization of the composite cathode formulation is of utmost importance. Unfortunately, many reports limit their studies to only a few parameters of the whole electrode formulation. In addition, different measurement setups and testing conditions employed for all-solid-state batteries make a comparison of results from mutually independent studies quite difficult. Therefore, a detailed investigation on different key parameters for preparation of cathodes employed in all-solid-state batteries is presented here. Employing a rational approach for optimization of composite cathodes using solid sulfide electrolytes elucidated the influence of different parameters on the cycling performance. First, powder electrodes made without binders are investigated to optimize several parameters, including the active materials’ particle morphology, the nature and amount of the conductive additive, the particle size of the solid electrolyte, as well as the active material-to-solid electrolyte ratio. Finally, cast electrodes are examined to determine the influence of a binder on cycling performance. Full article

(This article belongs to the Special Issue Sulfur Based Nanomaterials for Secondary Batteries)

► Show Figures

Graphical abstract

13 pages, 15211 KiB

Open AccessEditor’s ChoiceArticle

In Vitro Analysis of Superparamagnetic Iron Oxide Nanoparticles Coated with APTES as Possible Radiosensitizers for HNSCC Cells

by Clara Emer, Laura S. Hildebrand, Bernhard Friedrich, Rainer Tietze, Rainer Fietkau and Luitpold V. Distel

Nanomaterials 2023, 13(2), 330; https://doi.org/10.3390/nano13020330 - 12 Jan 2023

Cited by 1 | Viewed by 2333

Abstract

Superparamagnetic iron oxide nanoparticles (SPION) are being investigated for many purposes, e.g., for the amplification of ionizing radiation and for the targeted application of therapeutics. Therefore, we investigated SPIONs coated with (3-Aminopropyle)-Triethoxysilane (SPION-APTES) for their influence on different head and neck squamous cell [...] Read more.

Superparamagnetic iron oxide nanoparticles (SPION) are being investigated for many purposes, e.g., for the amplification of ionizing radiation and for the targeted application of therapeutics. Therefore, we investigated SPIONs coated with (3-Aminopropyle)-Triethoxysilane (SPION-APTES) for their influence on different head and neck squamous cell carcinoma (HNSCC) cell lines, as well as for their suitability as a radiosensitizer. We used 24-well microscopy and immunofluorescence microscopy for cell observation, growth curves to determine cytostatic effects, and colony formation assays to determine cytotoxicity. We found that the APTES-SPIONs were very well taken up by the HNSCC cells. They generally have a low cytotoxic effect, showing no significant difference in clonogenic survival between the control group and cells treated with 20 µg Fe/mL (p > 0.25) for all cell lines. They have a cytostatic effect on some cell lines cells (e.g., Cal33) that is visible across different radiation doses (1, 2, 8 Gy, p = 0.05). In Cal33, e.g., SPION-APTES raised the doubling time at 2 Gy from 24.53 h to 41.64 h. Importantly, these findings vary notably between the cell lines. However, they do not significantly alter the radiation effect: only one out of eight cell lines treated with SPION-APTES showed a significantly reduced clonogenic survival after ionizing radiation with 2 Gy, and only two showed significantly reduced doubling times. Thus, although the APTES-SPIONs do not qualify as a radiosensitizer, we were still able to vividly demonstrate and analyze the effect that the APTES-SPIONs have on various cell lines as a contribution to further functionalization. Full article

(This article belongs to the Section Biology and Medicines)

► Show Figures

Figure 1

12 pages, 2089 KiB

Open AccessEditor’s ChoiceArticle

Dietary Transfer of Zinc Oxide Nanoparticles Induces Locomotive Defects Associated with GABAergic Motor Neuron Damage in Caenorhabditis elegans

by Chun Ming How and Chi-Wei Huang

Nanomaterials 2023, 13(2), 289; https://doi.org/10.3390/nano13020289 - 10 Jan 2023

Cited by 6 | Viewed by 1873

Abstract

The widespread use of zinc oxide nanoparticles (ZnO-NPs) and their release into the environment have raised concerns about the potential toxicity caused by dietary transfer. However, the toxic effects and the mechanisms of dietary transfer of ZnO-NPs have rarely been investigated. We employed [...] Read more.

The widespread use of zinc oxide nanoparticles (ZnO-NPs) and their release into the environment have raised concerns about the potential toxicity caused by dietary transfer. However, the toxic effects and the mechanisms of dietary transfer of ZnO-NPs have rarely been investigated. We employed the bacteria-feeding nematode Caenorhabditis elegans as the model organism to investigate the neurotoxicity induced by exposure to ZnO-NPs via trophic transfer. Our results showed that ZnO-NPs accumulated in the intestine of C. elegans and also in Escherichia coli OP50 that they ingested. Additionally, impairment of locomotive behaviors, including decreased body bending and head thrashing frequencies, were observed in C. elegans that were fed E. coli pre-treated with ZnO-NPs, which might have occurred because of damage to the D-type GABAergic motor neurons. However, these toxic effects were not apparent in C. elegans that were fed E. coli pre-treated with zinc chloride (ZnCl₂). Therefore, ZnO-NPs particulates, rather than released Zn ions, damage the D-type GABAergic motor neurons and adversely affect the locomotive behaviors of C. elegans via dietary transfer. Full article

(This article belongs to the Special Issue Nanoparticles in the Environment and Nanotoxicology)

► Show Figures

Figure 1

13 pages, 4226 KiB

Open AccessEditor’s ChoiceArticle

In Situ Grown Mesoporous Structure of Fe-Dopant@NiCoO_X@NF Nanoneedles as an Efficient Supercapacitor Electrode Material

by Yedluri Anil Kumar, Ganesh Koyyada, Dasha Kumar Kulurumotlakatla, Jae Hong Kim, Md Moniruzzaman, Salem Alzahmi and Ihab M. Obaidat

Nanomaterials 2023, 13(2), 292; https://doi.org/10.3390/nano13020292 - 10 Jan 2023

Cited by 5 | Viewed by 2718

Abstract

In this study, we designed mixed metal oxides with doping compound nano-constructions as efficient electrode materials for supercapacitors (SCs). We successfully prepared the Fe-dopant with NiCoO_x grown on nickel foam (Fe-dopant@NiCoO_x@NF) through a simple hydrothermal route with annealing procedures. This [...] Read more.

In this study, we designed mixed metal oxides with doping compound nano-constructions as efficient electrode materials for supercapacitors (SCs). We successfully prepared the Fe-dopant with NiCoO_x grown on nickel foam (Fe-dopant@NiCoO_x@NF) through a simple hydrothermal route with annealing procedures. This method provides an easy route for the preparation of high activity SCs for energy storage. Obtained results revealed that the Fe dopant has successfully assisted NiCoO_x lattices. The electrochemical properties were investigated in a three-electrode configuration. As a composite electrode for SC characteristics, the Fe-dopant@NiCoO_x@NF exhibits notable electrochemical performances with very high specific capacitances of 1965 F g⁻¹ at the current density of 0.5 A g⁻¹, and even higher at 1296 F g⁻¹ and 30 A g⁻¹, respectively, which indicate eminent and greater potential for SCs. Moreover, the Fe-dopant@NiCoO_x@NF nanoneedle composite obtains outstanding cycling performances of 95.9% retention over 4500 long cycles. The improved SC activities of Fe-dopant@NiCoO_x@NF nanoneedles might be ascribed to the synergistic reactions of the ternary mixed metals, Fe-dopant, and the ordered nanosheets grown on NF. Thus, the Fe-dopant@NiCoO_x@NF nanoneedle composite with unique properties could lead to promising SC performance. Full article

(This article belongs to the Special Issue Advanced Functional Nanomaterials for Energy Storage Applications, Volume II)

► Show Figures

Figure 1

12 pages, 9453 KiB

Open AccessEditor’s ChoiceArticle

Supercurrent in Bi₄Te₃ Topological Material-Based Three-Terminal Junctions

by Jonas Kölzer, Abdur Rehman Jalil, Daniel Rosenbach, Lisa Arndt, Gregor Mussler, Peter Schüffelgen, Detlev Grützmacher, Hans Lüth and Thomas Schäpers

Nanomaterials 2023, 13(2), 293; https://doi.org/10.3390/nano13020293 - 10 Jan 2023

Cited by 7 | Viewed by 2471

Abstract

In this paper, in an in situ prepared three-terminal Josephson junction based on the topological insulator Bi

_{4}

Te

_{3}

and the superconductor Nb the transport properties are studied. The differential resistance maps as a function of two bias currents reveal extended areas [...] Read more.

In this paper, in an in situ prepared three-terminal Josephson junction based on the topological insulator Bi

_{4}

Te

_{3}

and the superconductor Nb the transport properties are studied. The differential resistance maps as a function of two bias currents reveal extended areas of Josephson supercurrent, including coupling effects between adjacent superconducting electrodes. The observed dynamics for the coupling of the junctions is interpreted using a numerical simulation of a similar geometry based on a resistively and capacitively shunted Josephson junction model. The temperature dependency indicates that the device behaves similar to prior experiments with single Josephson junctions comprising topological insulators’ weak links. Irradiating radio frequencies to the junction, we find a spectrum of integer Shapiro steps and an additional fractional step, which is interpreted with a skewed current–phase relationship. In a perpendicular magnetic field, we observe Fraunhofer-like interference patterns in the switching currents. Full article

(This article belongs to the Special Issue Topological Materials in Low Dimensions)

► Show Figures

Figure 1

19 pages, 6251 KiB

Open AccessEditor’s ChoiceArticle

Photocatalytic Degradation of Crystal Violet Dye under Visible Light by Fe-Doped TiO₂ Prepared by Reverse-Micelle Sol–Gel Method

by Antonietta Mancuso, Nicola Blangetti, Olga Sacco, Francesca Stefania Freyria, Barbara Bonelli, Serena Esposito, Diana Sannino and Vincenzo Vaiano

Nanomaterials 2023, 13(2), 270; https://doi.org/10.3390/nano13020270 - 8 Jan 2023

Cited by 36 | Viewed by 4201

Abstract

A reverse-micelle sol–gel method was chosen for the preparation of Fe-doped TiO₂ samples that were employed in the photodegradation of the crystal violet dye under visible light irradiation in a batch reactor. The dopant amount was varied to assess the optimal photocatalyst [...] Read more.

A reverse-micelle sol–gel method was chosen for the preparation of Fe-doped TiO₂ samples that were employed in the photodegradation of the crystal violet dye under visible light irradiation in a batch reactor. The dopant amount was varied to assess the optimal photocatalyst composition towards the target dye degradation. The photocatalysts were characterized through a multi-technique approach, envisaging XRPD and QPA as obtained by Rietveld refinement, FE-SEM analysis, DR UV−vis spectroscopy, N₂ adsorption/desorption isotherms measurement at −196 °C, ζ-potential measurement, and XPS analysis. The physical-chemical characterization showed that the adopted synthesis method allows obtaining NPs with uniform shape and size and promotes the introduction of Fe into the titania matrix, finally affecting the relative amounts of the three occurring polymorphs of TiO₂ (anatase, rutile and brookite). By increasing the Fe content, the band gap energy decreases from 3.13 eV (with undoped TiO₂) to 2.65 eV (with both 2.5 and 3.5 wt.% nominal Fe contents). At higher Fe content, surface Fe oxo-hydroxide species occur, as shown by DR UV-vis and XP spectroscopies. All the Fe-doped TiO₂ photocatalysts were active in the degradation and mineralization of the target dye, showing a TOC removal higher than the undoped sample. The photoactivity under visible light was ascribed both to the band-gap reduction (as confirmed by phenol photodegradation) and to dye sensitization of the photocatalyst surface (as confirmed by photocatalytic tests carried out using different visible-emission spectra LEDs). The main reactive species involved in the dye degradation were determined to be positive holes. Full article

► Show Figures

Figure 1

13 pages, 2379 KiB

Open AccessEditor’s ChoiceArticle

Wearable and Washable MnO₂−Zn Battery Packaged by Vacuum Sealing

by Jun Ho Noh, Myoungeun Oh, Sunjin Kang, Hyeong Seok Lee, Yeong Jun Hong, Chaeyeon Park, Raeyun Lee and Changsoon Choi

Nanomaterials 2023, 13(2), 265; https://doi.org/10.3390/nano13020265 - 7 Jan 2023

Cited by 3 | Viewed by 2542

Abstract

Batteries are used in all types of electronic devices from conventional to advanced devices. Currently, batteries are evolving in the direction of extremely personalized yarn− or textile−structured textronic systems. However, the absence of a protective layer on such batteries is a critical limitation [...] Read more.

Batteries are used in all types of electronic devices from conventional to advanced devices. Currently, batteries are evolving in the direction of extremely personalized yarn− or textile−structured textronic systems. However, the absence of a protective layer on such batteries is a critical limitation to their practical use. In this study, we developed a wearable and washable MnO₂−Zn textile battery that maintains its electrochemical capacity under various external environmental conditions through a vacuum−sealed packaging. The packaged textile battery was fabricated by vacuuming a polymer envelope containing the battery, followed by heat sealing with a vacuum packaging machine. The interior and exterior regions of the textile battery are completely separated by the packaging sheath to preclude leakage and intrusion of substances. The resulting packaged textile battery exhibits stable capacity retention performance under varying temperature and humidity; mechanical deformations due to bending, twisting, rubbing, and pressing; and several mechanical, chemical, and their combined washing cycles. On the basis of these demonstrations, we expect that our vacuum−packaged textile battery will offer new possibilities for practical and convenient use of textronics. Full article

► Show Figures

Figure 1

14 pages, 3545 KiB

Open AccessEditor’s ChoiceArticle

K_xCo_1.5−0.5xFe(CN)₆/rGO with Dual−Active Sodium Ion Storage Site as Superior Anode for Sodium Ion Battery

by Gang Zhou, Mincong Fan, Lei Wang, Xianglin Li, Danqing Liu and Feng Gao

Nanomaterials 2023, 13(2), 264; https://doi.org/10.3390/nano13020264 - 7 Jan 2023

Cited by 1 | Viewed by 1914

Abstract

The unique and open large frame structures of prussian blue analogues (PBA) enables it for accommodating a large number of cations (Na⁺, K⁺, Ca²⁺, etc.), thus, PBA are considered as promising electrode materials for the rechargeable battery. [...] Read more.

The unique and open large frame structures of prussian blue analogues (PBA) enables it for accommodating a large number of cations (Na⁺, K⁺, Ca²⁺, etc.), thus, PBA are considered as promising electrode materials for the rechargeable battery. However, due to the chemical composition, there are still many alkaline metal ions in the gap within the framework, which puts multivalent metals in PBA in a low valence state and affects the sodium storage performance. To improve the valence of metal ions in PBA materials, precursors prepared by co−precipitation method and hydrothermal method are used to synthesis K_xCo_1.5−0.5xFe(CN)₆ through further chemical oxidation. Through the introducing of reduced graphene oxide (rGO) with excellent conductivity by a simple physical mixing method, the cycle stability and rate performance of the PBA material can be further improved. The K_0.5Co_1.2Fe(CN)₆·2H₂O/rGO anode prepared with 2 h hydrothermal time and further chemical oxidation, named as KCoHCP−H2−EK/rGO, exhibits a super electrochemical performance, delivering initial charge/discharge capacities of 846.7/1445.0 mAh·g⁻¹, and a capacity retention of 58.2% after 100 cycles at a current density of 100 mA·g⁻¹. The KCoHCP−H2−EK/rGO outstanding electrochemical behaviors are attributed to the unique dual−active site structure properties and the improved surface conductance of materials by rGO components. Full article

(This article belongs to the Special Issue Functional Micro-/Nanostructures: Advanced Fabrication and Application)

► Show Figures

Figure 1

10 pages, 1719 KiB

Open AccessEditor’s ChoiceArticle

Capacitive NO₂ Detection Using CVD Graphene-Based Device

by Wonbin Ju and Sungbae Lee

Nanomaterials 2023, 13(2), 243; https://doi.org/10.3390/nano13020243 - 5 Jan 2023

Cited by 3 | Viewed by 1803

Abstract

A graphene-based capacitive NO₂ sensing device was developed by utilizing the quantum capacitance effect. We have used a graphene field-effect transistor (G-FET) device whose geometrical capacitance is enhanced by incorporating an aluminum back-gate electrode with a naturally oxidized aluminum surface as an [...] Read more.

A graphene-based capacitive NO₂ sensing device was developed by utilizing the quantum capacitance effect. We have used a graphene field-effect transistor (G-FET) device whose geometrical capacitance is enhanced by incorporating an aluminum back-gate electrode with a naturally oxidized aluminum surface as an insulating layer. When the graphene, the top-side of the device, is exposed to NO₂, the quantum capacitance of graphene and, thus, the measured capacitance of the device, changed in accordance with NO₂ concentrations ranging from 1–100 parts per million (ppm). The operational principle of the proposed system is also explained with the changes in gate voltage-dependent capacitance of the G-FET exposed to various concentrations of NO₂. Further analyses regarding carrier density changes and potential variances under various concentrations of NO₂ are also presented to strengthen the argument. The results demonstrate the feasibility of capacitive NO₂ sensing using graphene and the operational principle of capacitive NO₂ sensing. Full article

(This article belongs to the Special Issue Mechanical Properties and Applications of Graphene and Layered Nanocomposites)

► Show Figures

Figure 1

14 pages, 6255 KiB

Open AccessEditor’s ChoiceArticle

Effect of Polyphenols on the Ice-Nucleation Activity of Ultrafine Bubbles

by Tsutomu Uchida and Yukiharu Fukushi

Nanomaterials 2023, 13(1), 205; https://doi.org/10.3390/nano13010205 - 2 Jan 2023

Cited by 2 | Viewed by 2523

Abstract

Ultrafine bubbles (UFBs) in water provide a large amount of gas and a large gas–liquid interfacial area, and can release energy through their collapse. Such features may promote ice nucleation. Here, we examined the nucleation of ice in solutions containing polyphenols and UFBs. [...] Read more.

Ultrafine bubbles (UFBs) in water provide a large amount of gas and a large gas–liquid interfacial area, and can release energy through their collapse. Such features may promote ice nucleation. Here, we examined the nucleation of ice in solutions containing polyphenols and UFBs. To reduce the likelihood of nucleation occurring on the container walls over that in previous studies, we used a much larger sample volume of 1 mL. In our experiments, UFBs (when present) had a number concentration of 10⁸ mL⁻¹. We quantified changes to the nucleation activity by examining the shift in the cumulative freezing (nucleation) probability distribution. Compared to pure water, this freezing curve shifts approximately 0.6 °C higher with the UFBs. Then, to the water, we added three polyphenols (tannic acid TA, tea catechin TC, and oligonol OLG), chosen because they had been reported to reduce the ice-nucleation activity of heterogeneous ice nuclei (e.g., AgI). We found experimentally that, without UFBs, all polyphenols instead shift the pure-water freezing curve to a higher temperature. Then, when UFBs are added, the additional temperature shift in the freezing curve is slightly higher for OLG, essentially unchanged for TA, and slightly lower for TC. To help to explain these differences, we examined the UFB size distributions using dynamic light scattering and freeze-fractured replicas with transmission electron microscopy, finding that OLG and TC alter the UFBs, but that TA does not. Full article

(This article belongs to the Special Issue Nanobubbles and Their Applications)

► Show Figures

Figure 1

10 pages, 2935 KiB

Open AccessEditor’s ChoiceArticle

Improved Electrical Properties of EHD Jet-Patterned MoS₂ Thin-Film Transistors with Printed Ag Electrodes on a High-k Dielectric

by Thi Thu Thuy Can and Woon-Seop Choi

Nanomaterials 2023, 13(1), 194; https://doi.org/10.3390/nano13010194 - 1 Jan 2023

Cited by 5 | Viewed by 2231

Abstract

Electrohydrodynamic (EHD) jet printing is known as a versatile method to print a wide viscosity range of materials that are impossible to print by conventional inkjet printing. Hence, with the understanding of the benefits of EHD jet printing, solution-based MoS₂ and a [...] Read more.

Electrohydrodynamic (EHD) jet printing is known as a versatile method to print a wide viscosity range of materials that are impossible to print by conventional inkjet printing. Hence, with the understanding of the benefits of EHD jet printing, solution-based MoS₂ and a high-viscosity Ag paste were EHD jet-printed for electronic applications in this work. In particular, printed MoS₂ TFTs with a patterned Ag source and drain were successfully fabricated with low-k silica (SiO₂) and high-k alumina (Al₂O₃) gate dielectrics, respectively. Eventually, the devices based on Al₂O₃ exhibited much better electrical properties compared to the ones based on SiO₂. Interestingly, an improvement of around one order of magnitude in hysteresis was achieved for devices after changing the gate insulator from SiO₂ to Al₂O₃. In effect, the results of this work for the printed MoS₂ and the printed Ag source and drains for TFTs demonstrate a new approach for jet printing in the fabrication of electronic devices. Full article

(This article belongs to the Special Issue 2D Semiconducting Materials for Device Applications)

► Show Figures

Figure 1

16 pages, 5060 KiB

Open AccessEditor’s ChoiceArticle

Photodetection Properties of MoS₂, WS₂ and Mo_xW_1-xS₂ Heterostructure: A Comparative Study

by Maryam Al Qaydi, Ahmed Kotbi, Nitul S. Rajput, Abdellatif Bouchalkha, Mimoun El Marssi, Guillaume Matras, Chaouki Kasmi and Mustapha Jouiad

Nanomaterials 2023, 13(1), 24; https://doi.org/10.3390/nano13010024 - 21 Dec 2022

Cited by 8 | Viewed by 3428

Abstract

Layered transition metals dichalcogenides such as MoS₂ and WS₂ have shown a tunable bandgap, making them highly desirable for optoelectronic applications. Here, we report on one-step chemical vapor deposited MoS₂, WS₂ and Mo_xW_1-xS₂ [...] Read more.

Layered transition metals dichalcogenides such as MoS₂ and WS₂ have shown a tunable bandgap, making them highly desirable for optoelectronic applications. Here, we report on one-step chemical vapor deposited MoS₂, WS₂ and Mo_xW_1-xS₂ heterostructures incorporated into photoconductive devices to be examined and compared in view of their use as potential photodetectors. Vertically aligned MoS₂ nanosheets and horizontally stacked WS₂ layers, and their heterostructure form Mo_xW_1-xS₂, exhibit direct and indirect bandgap, respectively. To analyze these structures, various characterization methods were used to elucidate their properties including Raman spectroscopy, X-ray diffraction, X-ray photoelectron spectrometry and high-resolution transmission electron microscopy. While all the investigated samples show a photoresponse in a broad wavelength range between 400 nm and 700 nm, the vertical MoS₂ nanosheets sample exhibits the highest performances at a low bias voltage of 5 V. Our findings demonstrate a responsivity and a specific detectivity of 47.4 mA W⁻¹ and 1.4 × 10¹¹ Jones, respectively, achieved by Mo_xW_1-xS₂. This study offers insights into the use of a facile elaboration technique for tuning the performance of Mo_xW_1-xS₂ heterostructure-based photodetectors. Full article

(This article belongs to the Special Issue Advances in Nanostructured Semiconductors and Heterojunctions)

► Show Figures

Figure 1

15 pages, 4473 KiB

Open AccessEditor’s ChoiceArticle

Shear Bond Strength and Color Stability of Novel Antibacterial Nanofilled Dental Adhesive Resins

by Qing Hong, Alexandra C. Pierre-Bez, Matheus Kury, Mark E. Curtis, Rochelle D. Hiers, Fernando L. Esteban Florez and John C. Mitchell

Nanomaterials 2023, 13(1), 1; https://doi.org/10.3390/nano13010001 - 20 Dec 2022

Cited by 8 | Viewed by 2251

Abstract

Experimental adhesives containing co-doped metaloxide nanoparticles were demonstrated to display strong and long-term antibacterial properties against Streptococcus mutans biofilms. The present study represents an effort to characterize the shear-bond strength (SBS) and color stability (CS) of these novel biomaterials. Experimental adhesives were obtained [...] Read more.

Experimental adhesives containing co-doped metaloxide nanoparticles were demonstrated to display strong and long-term antibacterial properties against Streptococcus mutans biofilms. The present study represents an effort to characterize the shear-bond strength (SBS) and color stability (CS) of these novel biomaterials. Experimental adhesives were obtained by dispersing nitrogen and fluorine co-doped titanium dioxide nanoparticles (NF_TiO₂, 10%, 20% or 30%, v/v%) into OptiBond Solo Plus (OPTB). Dentin surfaces were wet-polished (600-Grit). Specimens (n = 5/group) of Tetric EvoCeram were fabricated and bonded using either OPTB or experimental (OPTB + NF_TiO₂) adhesives. Specimens were stored in water (37 °C) for twenty-four hours (T1), three months (T2), and six months (T3). At T1, T2, or T3, specimens were removed from water storage and were tested for SBS. Disc-shaped specimens (n = 10/group; d = 6.0 mm, t = 0.5 mm) of adhesives investigated were fabricated and subjected to thermocycling (10,000 cycles, 5–55 °C, 15 s dwell time). Specimens’ colors were determined with a VITA Easyshade^® V spectrophotometer (after every 1000 cycles). SBS data was analyzed using two-way ANOVA and post-hoc Tukey tests, while CS data was analyzed using one-way ANOVA and post-hoc Tukey tests (α = 0.05). Mean values of SBS ranged from 16.39 ± 4.20 MPa (OPTB + 30%NF_TiO₂) to 19.11 ± 1.11 MPa (OPTB), from 12.99 ± 2.53 MPa (OPTB + 30% NF_TiO₂) to 14.87 ± 2.02 (OPTB) and from 11.37 ± 1.89 (OPTB + 20% NF_TiO₂) to 14.19 ± 2.24 (OPTB) after twenty-four hours, three months, and six months of water storage, respectively. Experimental materials had SBS values that were comparable (p > 0.05) to those from OPTB independently of nanoparticle concentration or time-point considered. Experimental materials with higher NF_TiO₂ concentrations had less intense color variations and were more color stable than OPTB even after 10,000 thermocycles. In combination, the results reported have demonstrated that experimental adhesives can establish strong and durable bonds to human dentin while displaying colors that are more stable, thereby suggesting that the antibacterial nanotechnology investigated can withstand the harsh conditions within the oral cavity without compromising the esthetic component of dental restorations. Full article

(This article belongs to the Special Issue Synthesis and Application of Nanoparticles in Novel Composites)

► Show Figures

Figure 1

16 pages, 6500 KiB

Open AccessEditor’s ChoiceArticle

Insights into the Stability of Graphene Oxide Aqueous Dispersions

by Codrut Costinas, Catalin Alexandru Salagean, Liviu Cosmin Cotet, Monica Baia, Milica Todea, Klara Magyari and Lucian Baia

Nanomaterials 2022, 12(24), 4489; https://doi.org/10.3390/nano12244489 - 19 Dec 2022

Cited by 7 | Viewed by 2010

Abstract

Understanding graphene oxide’s stability (or lack thereof) in liquid solvents is critical for fine-tuning the material’s characteristics and its potential involvement in future applications. In this work, through the use of structural and surface investigations, the alteration of the structural and edge-surface properties [...] Read more.

Understanding graphene oxide’s stability (or lack thereof) in liquid solvents is critical for fine-tuning the material’s characteristics and its potential involvement in future applications. In this work, through the use of structural and surface investigations, the alteration of the structural and edge-surface properties of 2D graphene oxide nanosheets was monitored over a period of eight weeks by involving DLS, zeta potential, XRD, XPS, Raman and FT-IR spectroscopy techniques. The samples were synthesized as an aqueous suspension by an original modified Marcano-Tour method centred on the sono-chemical exfoliation of graphite. Based on the acquired experimental results and the available literature, a phenomenological explanation of the two underlying mechanisms responsible for the meta-stability of graphene oxide aqueous dispersions is proposed. It is based on the cleavage of the carbon bonds in the first 3–4 weeks, while the bonding of oxygen functional groups on the carbon lattice occurs, and the transformation of epoxide and hydroxyl groups into adsorbed water molecules in a process driven by the availability of hydrogen in graphene oxide nanosheets. Full article

(This article belongs to the Special Issue Synthesis, Modification and Application of Graphene)

► Show Figures

Figure 1

11 pages, 2429 KiB

Open AccessEditor’s ChoiceArticle

Biocompatibility, Bioactivity, and Antibacterial Behaviour of Cerium-Containing Bioglass^®

by Sílvia R. Gavinho, Ana Sofia Pádua, Isabel Sá-Nogueira, Jorge C. Silva, João P. Borges, Luis C. Costa and Manuel Pedro F. Graça

Nanomaterials 2022, 12(24), 4479; https://doi.org/10.3390/nano12244479 - 18 Dec 2022

Cited by 22 | Viewed by 2969

Abstract

The main reason for the increased use of dental implants in clinical practice is associated with aesthetic parameters. Implants are also presented as the only technique that conserves and stimulates natural bone. However, there are several problems associated with infections, such as peri-implantitis. [...] Read more.

The main reason for the increased use of dental implants in clinical practice is associated with aesthetic parameters. Implants are also presented as the only technique that conserves and stimulates natural bone. However, there are several problems associated with infections, such as peri-implantitis. This disease reveals a progressive inflammatory action that affects the hard and soft tissues surrounding the implant, leading to implant loss. To prevent the onset of this disease, coating the implant with bioactive glasses has been suggested. In addition to its intrinsic function of promoting bone regeneration, it is also possible to insert therapeutic ions, such as cerium. Cerium has several advantages when the aim is to improve osseointegration and prevent infectious problems with dental implant placement. It promotes increased growth and the differentiation of osteoblasts, improves the mechanical properties of bone, and prevents bacterial adhesion and proliferation that may occur on the implant surface. This antibacterial effect is due to its ability to disrupt the cell wall and membrane of bacteria, thus interfering with vital metabolic functions such as respiration. In addition, its antioxidant effect reverses oxidative stress after implantation in bone. In this work, Bioglass 45S5 with CeO₂ with different percentages (0.25, 0.5, 1, and 2 mol%) was developed by the melt-quenching method. The materials were analyzed in terms of morphological, structural, and biological (cytotoxicity, bioactivity, and antibacterial activity) properties. The addition of cerium did not promote structural changes to the bioactive glass, which shows no cytotoxicity for the Saos-2 cell line up to 25 mg/mL of extract concentration for all cerium contents. For the maximum cerium concentration (2 mol%) the bioactive glass shows an evident inhibitory effect for Escherichia coli and Streptococcus mutans bacteria. Furthermore, all samples showed the beginning of the deposition of a CaP-rich layer on the surface of the material after 24 h. Full article

(This article belongs to the Special Issue Nanobiotechnologies in Environment and Medicine)

► Show Figures

Figure 1

19 pages, 5643 KiB

Open AccessEditor’s ChoiceArticle

3D Nanoprinting of All-Metal Nanoprobes for Electric AFM Modes

by Lukas Matthias Seewald, Jürgen Sattelkow, Michele Brugger-Hatzl, Gerald Kothleitner, Hajo Frerichs, Christian Schwalb, Stefan Hummel and Harald Plank

Nanomaterials 2022, 12(24), 4477; https://doi.org/10.3390/nano12244477 - 17 Dec 2022

Cited by 6 | Viewed by 2218

Abstract

3D nanoprinting via focused electron beam induced deposition (FEBID) is applied for fabrication of all-metal nanoprobes for atomic force microscopy (AFM)-based electrical operation modes. The 3D tip concept is based on a hollow-cone (HC) design, with all-metal material properties and apex radii in [...] Read more.

3D nanoprinting via focused electron beam induced deposition (FEBID) is applied for fabrication of all-metal nanoprobes for atomic force microscopy (AFM)-based electrical operation modes. The 3D tip concept is based on a hollow-cone (HC) design, with all-metal material properties and apex radii in the sub-10 nm regime to allow for high-resolution imaging during morphological imaging, conductive AFM (CAFM) and electrostatic force microscopy (EFM). The study starts with design aspects to motivate the proposed HC architecture, followed by detailed fabrication characterization to identify and optimize FEBID process parameters. To arrive at desired material properties, e-beam assisted purification in low-pressure water atmospheres was applied at room temperature, which enabled the removal of carbon impurities from as-deposited structures. The microstructure of final HCs was analyzed via scanning transmission electron microscopy—high-angle annular dark field (STEM-HAADF), whereas electrical and mechanical properties were investigated in situ using micromanipulators. Finally, AFM/EFM/CAFM measurements were performed in comparison to non-functional, high-resolution tips and commercially available electric probes. In essence, we demonstrate that the proposed all-metal HCs provide the resolution capabilities of the former, with the electric conductivity of the latter onboard, combining both assets in one design. Full article

(This article belongs to the Special Issue Nanomaterials Fabricated by Electron-Beam-Induced Deposition and Related Processes)

► Show Figures

Figure 1

20 pages, 2945 KiB

Open AccessEditor’s ChoiceArticle

Towards Improved Humidity Sensing Nanomaterials via Combined Electron and NH₃ Treatment of Carbon-Rich FEBID Deposits

by Hannah Boeckers, Petra Swiderek and Markus Rohdenburg

Nanomaterials 2022, 12(24), 4455; https://doi.org/10.3390/nano12244455 - 15 Dec 2022

Cited by 1 | Viewed by 1848

Abstract

Focused Electron Beam Induced Deposition (FEBID) is a unique tool to produce nanoscale materials. The resulting deposits can be used, for instance, as humidity or strain sensors. The humidity sensing concept relies on the fact that FEBID using organometallic precursors often yields deposits [...] Read more.

Focused Electron Beam Induced Deposition (FEBID) is a unique tool to produce nanoscale materials. The resulting deposits can be used, for instance, as humidity or strain sensors. The humidity sensing concept relies on the fact that FEBID using organometallic precursors often yields deposits which consist of metal nanoparticles embedded in a carbonaceous matrix. The electrical conductivity of such materials is altered in the presence of polar molecules such as water. Herein, we provide evidence that the interaction with water can be enhanced by incorporating nitrogen in the deposit through post-deposition electron irradiation in presence of ammonia (NH₃). This opens the perspective to improve and tune the properties of humidity sensors fabricated by FEBID. As a proof-of-concept experiment, we have prepared carbonaceous deposits by electron irradiation of adsorbed layers of three different precursors, namely, the aliphatic hydrocarbon n-pentane, a simple alkene (2-methyl-2-butene), and the potential Ru FEBID precursor bis(ethylcyclopentadienyl)ruthenium(II). In a subsequent processing step, we incorporated C-N bonds in the deposit by electron irradiation of adsorbed NH₃. To test the resulting material with respect to its potential humidity sensing capabilities, we condensed sub-monolayer quantities of water (H₂O) on the deposit and evaluated their thermal desorption behavior. The results confirm that the desorption temperature of H₂O decisively depends on the degree of N incorporation into the carbonaceous residue which, in turn, depends on the chemical nature of the precursor used for deposition of the carbonaceous layer. We thus anticipate that the sensitivity of a FEBID-based humidity sensor can be tuned by a precisely timed post-deposition electron and NH₃ processing step. Full article

(This article belongs to the Special Issue Nanomaterials Fabricated by Electron-Beam-Induced Deposition and Related Processes)

► Show Figures

Figure 1

14 pages, 4899 KiB

Open AccessEditor’s ChoiceArticle

Electrical Contact Resistance of Large-Area Graphene on Pre-Patterned Cu and Au Electrodes

by Tomáš Blecha, Zuzana Vlčková Živcová, Farjana J. Sonia, Martin Mergl, Oleksandr Volochanskyi, Michal Bodnár, Pavel Rous, Kenichiro Mizohata, Martin Kalbáč and Otakar Frank

Nanomaterials 2022, 12(24), 4444; https://doi.org/10.3390/nano12244444 - 14 Dec 2022

Cited by 4 | Viewed by 2998

Abstract

Contact resistance between electrically connected parts of electronic elements can negatively affect their resulting properties and parameters. The contact resistance is influenced by the physicochemical properties of the connected elements and, in most cases, the lowest possible value is required. The issue of [...] Read more.

Contact resistance between electrically connected parts of electronic elements can negatively affect their resulting properties and parameters. The contact resistance is influenced by the physicochemical properties of the connected elements and, in most cases, the lowest possible value is required. The issue of contact resistance is also addressed in connection with the increasingly frequently used carbon allotropes. This work aimed to determine the factors that influence contact resistance between graphene prepared by chemical vapour deposition and pre-patterned Cu and Au electrodes onto which graphene is subsequently transferred. It was found that electrode surface treatment methods affect the resistance between Cu and graphene, where contact resistance varied greatly, with an average of 1.25 ± 1.54 kΩ, whereas for the Au electrodes, the deposition techniques did not influence the resulting contact resistance, which decreased by almost two orders of magnitude compared with the Cu electrodes, to 0.03 ± 0.01 kΩ. Full article

(This article belongs to the Special Issue Nanofabrication and Nanomanipulation in Graphene)

► Show Figures

Figure 1

20 pages, 2617 KiB

Open AccessEditor’s ChoiceArticle

Interaction of Colloidal Gold Nanoparticles with Urine and Saliva Biofluids: An Exploratory Study

by Maria António, Tânia Lima, Rui Vitorino and Ana L. Daniel-da-Silva

Nanomaterials 2022, 12(24), 4434; https://doi.org/10.3390/nano12244434 - 13 Dec 2022

Cited by 2 | Viewed by 2124

Abstract

The use of gold nanoparticles for drug delivery, photothermal or photodynamic therapy, and biosensing enhances the demand for knowledge about the protein corona formed on the surface of nanoparticles. In this study, gold nanospheres (AuNSs), gold nanorods (AuNRs), and gold nanoflowers (AuNFs) were [...] Read more.

The use of gold nanoparticles for drug delivery, photothermal or photodynamic therapy, and biosensing enhances the demand for knowledge about the protein corona formed on the surface of nanoparticles. In this study, gold nanospheres (AuNSs), gold nanorods (AuNRs), and gold nanoflowers (AuNFs) were incubated with saliva or urine. After the interaction, the surface of gold nanoparticles was investigated using UV-VIS spectroscopy, zeta potential, and dynamic light scattering. The shifting of the localized surface plasmon resonance (LSPR) band, the increase in hydrodynamic diameter, and the changes in the surface charge of nanoparticles indicated the presence of biomolecules on the surface of AuNSs, AuNRs, and AuNFs. The incubation of AuNFs with saliva led to nanoparticle aggregation and minimal protein adsorption. AuNSs and AuNRs incubated in saliva were analyzed through liquid chromatography with tandem mass spectrometry (LC-MS/MS) to identify the 96 proteins adsorbed on the surface of the gold nanoparticles. Among the 20 most abundant proteins identified, 14 proteins were common in both AuNSs and AuNRs. We hypothesize that the adsorption of these proteins was due to their high sulfur content, allowing for their interaction with gold nanoparticles via the Au-S bond. The presence of distinct proteins on the surface of AuNSs or AuNRs was also investigated and possibly related to the competition between proteins present on the external layers of corona and gold nanoparticle morphology. Full article

► Show Figures

Graphical abstract

9 pages, 3650 KiB

Open AccessFeature PaperEditor’s ChoiceArticle

Enhanced Field-Effect Control of Single-Layer WS₂ Optical Features by hBN Full Encapsulation

by Anna Di Renzo, Onur Çakıroğlu, Felix Carrascoso, Hao Li, Giuseppe Gigli, Kenji Watanabe, Takashi Taniguchi, Carmen Munuera, Aurora Rizzo, Andres Castellanos-Gomez, Rosanna Mastria and Riccardo Frisenda

Nanomaterials 2022, 12(24), 4425; https://doi.org/10.3390/nano12244425 - 12 Dec 2022

Cited by 1 | Viewed by 2164

Abstract

The field-effect control of the electrical and optical properties of two-dimensional (2D) van der Waals semiconductors (vdW) is one important aspect of this novel class of materials. Thanks to their reduced thickness and decreased screening, electric fields can easily penetrate in a 2D [...] Read more.

The field-effect control of the electrical and optical properties of two-dimensional (2D) van der Waals semiconductors (vdW) is one important aspect of this novel class of materials. Thanks to their reduced thickness and decreased screening, electric fields can easily penetrate in a 2D semiconductor and thus modulate their charge density and their properties. In literature, the field effect is routinely used to fabricate atomically thin field-effect transistors based on 2D semiconductors. Apart from the tuning of the electrical transport, it has been demonstrated that the field effect can also be used to modulate the excitonic optical emission of 2D transition metal dichalcogenides such as MoS₂ or WSe₂. In this paper, we present some recent experiments on the field-effect control of the optical and excitonic properties of the monolayer WS₂. Using the deterministic transfer of van der Waals materials, we fabricate planar single-layer WS₂ devices contacted by a gold electrode and partially sandwiched between two insulating hexagonal boron nitride (hBN) flakes. Thanks to the planar nature of the device, we can optically access both the hBN encapsulated and the unencapsulated WS₂ regions and compare the field-effect control of the exciton population in the two cases. We find that the encapsulation strongly increases the range of tunability of the optical emission of WS₂, allowing us to tune the photoluminescence emission from excitons-dominated to trions-dominated. We also discuss how the full encapsulation of WS₂ with hBN helps reduce spurious hysteretic effects in the field-effect control of the optical properties, similar to what has been reported for 2D vdW field-effect transistors. Full article

(This article belongs to the Special Issue Advances in Semiconductor Nano-Structures)

► Show Figures

Graphical abstract

19 pages, 4737 KiB

Open AccessEditor’s ChoiceArticle

Effective Antibacterial/Photocatalytic Activity of ZnO Nanomaterials Synthesized under Low Temperature and Alkaline Conditions

by Sujeong Kim, Hyerim Park, Sadanand Pandey, Daewon Jeong, Chul-Tae Lee, Jeong Yeon Do, Sun-Min Park and Misook Kang

Nanomaterials 2022, 12(24), 4417; https://doi.org/10.3390/nano12244417 - 11 Dec 2022

Cited by 10 | Viewed by 1941

Abstract

The purpose of this study was to evaluate the surface properties of ZnO nanomaterials based on their ability to photodegrade methyl blue dye (MB) and to show their antibacterial properties against different types of Gram-positive bacteria (Bacillus manliponensis, Micrococcus luteus, [...] Read more.

The purpose of this study was to evaluate the surface properties of ZnO nanomaterials based on their ability to photodegrade methyl blue dye (MB) and to show their antibacterial properties against different types of Gram-positive bacteria (Bacillus manliponensis, Micrococcus luteus, Staphylococcus aureus) and Gram-negative bacteria (Escherichia coli). In this study, ZnO nanomaterials were synthesized rapidly and easily in the presence of 1–4 M NaOH at a low temperature of 40 °C within 4 h. It was found that the ZnO nanomaterials obtained from the 1.0 M (ZnO–1M) and 2.0 M (ZnO–2M) aqueous solutions of NaOH had spherical and needle-shaped forms, respectively. As the concentration of NaOH increased, needle thickness increased and the particles became rod-like. Although the ZnO nanomaterial shapes were different, the bandgap size remained almost unchanged. However, as the NaOH concentration increased, the energy position of the conduction band shifted upward. Photo current curves and photoluminescence intensities suggested that the recombination between photoexcited electrons and holes was low in the ZnO–4M materials prepared in 4.0 M NaOH solution; however, charge transfer was easy. ∙O₂⁻ radicals were generated more than ∙OH radicals in ZnO–4M particles, showing stronger antibacterial activity against both Gram-positive and Gram-negative bacteria and stronger decomposition ability on MB dye. The results of this study suggest that on the ZnO nanomaterial surface, ∙O₂⁻ radicals generated are more critical for antibacterial activity than particle shape. Full article

(This article belongs to the Special Issue Synthesis of Nanomaterials as Electrocatalysis, Photocatalysis and Thermal Catalysis)

► Show Figures

Figure 1

33 pages, 21104 KiB

Open AccessEditor’s ChoiceArticle

Micromagnetic Design of Skyrmionic Materials and Chiral Magnetic Configurations in Patterned Nanostructures for Neuromorphic and Qubit Applications

by Roxana-Alina One, Sever Mican, Angela-Georgiana Cimpoeșu, Marius Joldos, Romulus Tetean and Coriolan Viorel Tiușan

Nanomaterials 2022, 12(24), 4411; https://doi.org/10.3390/nano12244411 - 10 Dec 2022

Cited by 2 | Viewed by 2432

Abstract

Our study addresses the problematics of magnetic skyrmions, nanometer-size vortex-like swirling topological defects, broadly studied today for applications in classic, neuromorphic and quantum information technologies. We tackle some challenging issues of material properties versus skyrmion stability and manipulation within a multiple-scale modeling framework, [...] Read more.

Our study addresses the problematics of magnetic skyrmions, nanometer-size vortex-like swirling topological defects, broadly studied today for applications in classic, neuromorphic and quantum information technologies. We tackle some challenging issues of material properties versus skyrmion stability and manipulation within a multiple-scale modeling framework, involving complementary ab-initio and micromagnetic frameworks. Ab-initio calculations provide insight into the anatomy of the magnetic anisotropy, the Dzyaloshinskii–Moriya asymmetric exchange interaction (DMI) and their response to a gating electric field. Various multi-layered heterostructures were specially designed to provide electric field tunable perpendicular magnetization and sizeable DMI, which are required for skyrmion occurrence. Landau–Lifshitz–Gilbert micromagnetic calculations in nanometric disks allowed the extraction of material parameter phase diagrams in which magnetic textures were classified according to their topological charge. We identified suitable ranges of magnetic anisotropy, DMI and saturation magnetization for stabilizing skyrmionic ground states or writing/manipulating them using either a spin-transfer torque of a perpendicular current or the electric field. From analyzing the different contributions to the total magnetic free energy, we point out some critical properties influencing the skyrmions’ stability. Finally, we discuss some experimental issues related to the choice of materials or the design of novel magnetic materials compatible with skyrmionic applications. Full article

(This article belongs to the Special Issue New Achievements in Nanostructured and Low Dimensional Materials and Systems)

► Show Figures

Graphical abstract

13 pages, 2991 KiB

Open AccessEditor’s ChoiceArticle

Hydrogenated Amorphous Silicon-Based Nanomaterials as Alternative Electrodes to Graphite for Lithium-Ion Batteries

by Rocío Barrio, Nieves González, Álvaro Portugal, Carmen Morant and José Javier Gandía

Nanomaterials 2022, 12(24), 4400; https://doi.org/10.3390/nano12244400 - 9 Dec 2022

Cited by 1 | Viewed by 1737

Abstract

Graphite is the material most used as an electrode in commercial lithium-ion batteries. On the other hand, it is a material with low energy capacity, and it is considered a raw critical material given its large volume of use. In the current energy [...] Read more.

Graphite is the material most used as an electrode in commercial lithium-ion batteries. On the other hand, it is a material with low energy capacity, and it is considered a raw critical material given its large volume of use. In the current energy context, we must promote the search for alternative materials based on elements that are abundant, sustainable and that have better performance for energy storage. We propose thin materials based on silicon, which has a storage capacity eleven times higher than graphite. Nevertheless, due to the high-volume expansion during lithiation, it tends to crack, limiting the life of the batteries. To solve this problem, hydrogenated amorphous silicon has been researched, in the form of thin film and nanostructures, since, due to its amorphous structure, porosity and high specific surface, it could better absorb changes in volume. These thin films were grown by plasma-enhanced chemical vapor deposition, and then the nanowires were obtained by chemical etching. The compositional variations of films deposited at different temperatures and the incorporation of dopants markedly influence the stability and longevity of batteries. With these optimized electrodes, we achieved batteries with an initial capacity of 3800 mAhg⁻¹ and 82% capacity retention after 50 cycles. Full article

(This article belongs to the Special Issue Application of Nanomaterials for Electrochemical Energy Conversion and Storage Devices)

► Show Figures

Figure 1

15 pages, 3093 KiB

Open AccessEditor’s ChoiceArticle

Mechanically Enhanced Nanocrystalline Cellulose/Reduced Graphene Oxide/Polyethylene Glycol Electrically Conductive Composite Film

by Pengbo Xie, Ying Ge, Yida Wang, Jing Zhou, Yuanyuan Miao and Zhenbo Liu

Nanomaterials 2022, 12(24), 4371; https://doi.org/10.3390/nano12244371 - 8 Dec 2022

Cited by 3 | Viewed by 1914

Abstract

Traditional conductive materials do not meet the increasing requirements of electronic products because of such materials’ high rigidity, poor flexibility, and slow biodegradation after disposal. Preparing flexible conductive materials with excellent mechanical properties is an active area of research. The key to flexible [...] Read more.

Traditional conductive materials do not meet the increasing requirements of electronic products because of such materials’ high rigidity, poor flexibility, and slow biodegradation after disposal. Preparing flexible conductive materials with excellent mechanical properties is an active area of research. The key to flexible conductive materials lies in the combination of the polymer matrix and conductive components. This combination can be achieved by making a film of renewable nano-microcrystalline cellulose (NCC) and reduced graphene oxide (rGO) with excellent electrical conductivity—by simple filtration and introducing polyethylene glycol (PEG) to enhance the functionality of the composite film. Graphene imparted conductivity to the composite film, which reached 5.67 S·m⁻¹. A reinforced NCC/rGO/PEG-4 composite film with a thickness of only 21 μm exhibited a tensile strength of 30.56 MPa, which was 83% higher than that of the sample without PEG (16.71 MPa), and toughness of 727.18 kJ·m⁻³, which was about 132% higher than that of the control sample (NCC/rGO, 313.86 kJ·m⁻³). This ultra-thin conductive composite film—which can be prepared simply, consists of environmentally sustainable and biodegradable raw materials, and exhibits excellent mechanical properties—has substantial potential for applications in e.g., flexible electronic wearable devices, electrodes, and capacitors. Full article

► Show Figures

Graphical abstract

12 pages, 5293 KiB

Open AccessEditor’s ChoiceArticle

Green Extraction of Graphene from Natural Mineral Shungite

by Anastasia Novikova and Alina Karabchevsky

Nanomaterials 2022, 12(24), 4356; https://doi.org/10.3390/nano12244356 - 7 Dec 2022

Cited by 4 | Viewed by 1906

Abstract

Conventional fabrication methods to produce graphene are cumbersome, expensive, and not ecologically friendly. This is due to the fact that the processing of a large volume of raw materials requires large amounts of acids and alkalis which, in turn, require special disposal. Therefore, [...] Read more.

Conventional fabrication methods to produce graphene are cumbersome, expensive, and not ecologically friendly. This is due to the fact that the processing of a large volume of raw materials requires large amounts of acids and alkalis which, in turn, require special disposal. Therefore, it is necessary to develop new technologies or to refine existing ones for the production of graphene—and to create new, ecologically-safe and effective methods. Here, we utilized physical sonication to extract graphene films from natural mineral shungite rock. From our study of the structure of shungite by Raman spectrometry and X-ray phase analysis, we found that shungite is characterized by graphite-like mineral structures. Transmission electron microscopy images obtained from the processed material revealed graphene films—with surfaces as small as 200 nanometers long and several layers wide. Our green method of fabicating graphene can be widely used in a variety of fields, from electro-optics to ecology, to list a few. Full article

(This article belongs to the Special Issue 2D Materials for Advanced Sensors: Fabrication and Applications)

► Show Figures

Figure 1

13 pages, 4997 KiB

Open AccessFeature PaperEditor’s ChoiceArticle

Antiviral Properties against SARS-CoV-2 of Nanostructured ZnO Obtained by Green Combustion Synthesis and Coated in Waterborne Acrylic Coatings

by Julia de O. Primo, Jamille de S. Correa, Dienifer F. L. Horsth, Arkaprava Das, Marcin Zając, Polona Umek, Ruddy Wattiez, Fauze J. Anaissi, Rob C. A. Onderwater and Carla Bittencourt

Nanomaterials 2022, 12(23), 4345; https://doi.org/10.3390/nano12234345 - 6 Dec 2022

Cited by 6 | Viewed by 2413

Abstract

The COVID-19 pandemic has increased the need for developing disinfectant surfaces as well as reducing the spread of infections on contaminated surfaces and the contamination risk from the fomite route. The present work reports on the antiviral activity of coatings containing ZnO particles [...] Read more.

The COVID-19 pandemic has increased the need for developing disinfectant surfaces as well as reducing the spread of infections on contaminated surfaces and the contamination risk from the fomite route. The present work reports on the antiviral activity of coatings containing ZnO particles obtained by two simple synthesis routes using Aloe vera (ZnO-aloe) or cassava starch (ZnO-starch) as reaction fuel. After detailed characterization using XRD and NEXAFS, the obtained ZnO particles were dispersed in a proportion of 10% with two different waterborne acrylic coatings (binder and commercial white paint) and brushed on the surface of polycarbonates (PC). The cured ZnO/coatings were characterized by scanning electron microscopes (SEM) and energy-dispersive X-ray spectroscopy (EDS). Wettability tests were performed. The virucidal activity of the ZnO particles dispersed in the waterborne acrylic coating was compared to a reference control sample (PC plates). According to RT-PCR results, the ZnO-aloe/coating displays the highest outcome for antiviral activity against SARS-CoV-2 using the acrylic binder, inactivating >99% of the virus after 24 h of contact relative to reference control. Full article

(This article belongs to the Special Issue Applications of Nanomaterials in Diagnostics and Therapeutics)

► Show Figures

Figure 1

14 pages, 3264 KiB

Open AccessEditor’s ChoiceArticle

Postproduction Approach to Enhance the External Quantum Efficiency for Red Light-Emitting Diodes Based on Silicon Nanocrystals

by Hiroyuki Yamada, Junpei Watanabe, Kazuhiro Nemoto, Hong-Tao Sun and Naoto Shirahata

Nanomaterials 2022, 12(23), 4314; https://doi.org/10.3390/nano12234314 - 5 Dec 2022

Cited by 4 | Viewed by 2007

Abstract

Despite bulk crystals of silicon (Si) being indirect bandgap semiconductors, their quantum dots (QDs) exhibit the superior photoluminescence (PL) properties including high quantum yield (PLQY > 50%) and spectral tunability in a broad wavelength range. Nevertheless, their low optical absorbance character inhibits the [...] Read more.

Despite bulk crystals of silicon (Si) being indirect bandgap semiconductors, their quantum dots (QDs) exhibit the superior photoluminescence (PL) properties including high quantum yield (PLQY > 50%) and spectral tunability in a broad wavelength range. Nevertheless, their low optical absorbance character inhibits the bright emission from the SiQDs for phosphor-type light emitting diodes (LEDs). In contrast, a strong electroluminescence is potentially given by serving SiQDs as an emissive layer of current-driven LEDs with (Si-QLEDs) because the charged carriers are supplied from electrodes unlike absorption of light. Herein, we report that the external quantum efficiency (EQE) of Si-QLED was enhanced up to 12.2% by postproduction effect which induced by continuously applied voltage at 5 V for 9 h. The active layer consisted of SiQDs with a diameter of 2.0 nm. Observation of the cross-section of the multilayer QLEDs device revealed that the interparticle distance between adjacent SiQDs in the emissive layer is reduced to 0.95 nm from 1.54 nm by “post-electric-annealing”. The shortened distance was effective in promoting charge injection into the emission layer, leading improvement of the EQE. Full article

(This article belongs to the Special Issue Low-Dimensional Semiconductor Materials: Fabrication, Characterization and Applications)

► Show Figures

Graphical abstract

21 pages, 4805 KiB

Open AccessEditor’s ChoiceArticle

Conducting Electrospun Nanofibres: Monitoring of Iodine Doping of P3HT through Infrared (IRAV) and Raman (RaAV) Polaron Spectroscopic Features

by Alessia Arrigoni, Luigi Brambilla, Chiara Castiglioni and Chiara Bertarelli

Nanomaterials 2022, 12(23), 4308; https://doi.org/10.3390/nano12234308 - 4 Dec 2022

Cited by 3 | Viewed by 2024

Abstract

Aligned polymer nanofibres are prepared by means of the electrospinning of a chlorobenzene solution containing regioregular poly(3-hexyltiophene-2,5-diyl), P3HT, and poly(ethylene oxide), PEO. The PEO scaffold is easily dissolved with acetonitrile, leaving pure P3HT fibres, which do not show structural modification. Polymer fibres, either [...] Read more.

Aligned polymer nanofibres are prepared by means of the electrospinning of a chlorobenzene solution containing regioregular poly(3-hexyltiophene-2,5-diyl), P3HT, and poly(ethylene oxide), PEO. The PEO scaffold is easily dissolved with acetonitrile, leaving pure P3HT fibres, which do not show structural modification. Polymer fibres, either with or without the PEO supporting polymer, are effectively doped by exposure to iodine vapours. Doping is monitored following the changes in the doping-induced vibrational bands (IRAVs) observed in the infrared spectra and by means of Raman spectroscopy. Molecular orientation inside the fibres has been assessed by means of IR experiments in polarised light, clearly demonstrating that electrospinning induces the orientation of the polymer chains along the fibre axis as well as of the defects introduced by doping. This work illustrates a case study that contributes to the fundamental knowledge of the vibrational properties of the doping-induced defects—charged polarons—of P3HT. Moreover, it provides experimental protocols for a thorough spectroscopic characterisation of the P3HT nanofibres, and of doped conjugated polymers in general, opening the way for the control of the material structure when the doped polymer is confined in a one-dimensional architecture. Full article

(This article belongs to the Special Issue Synthesis, Characterization and Application of Nanofibers)

► Show Figures

Graphical abstract

11 pages, 2547 KiB

Open AccessEditor’s ChoiceArticle

Silver Nanoparticle Chains for Ultra-Long-Range Plasmonic Waveguides for Nd³⁺ Fluorescence

by Javier Fernández-Martínez, Sol Carretero-Palacios, Pablo Molina, Jorge Bravo-Abad, Mariola O. Ramírez and Luisa E. Bausá

Nanomaterials 2022, 12(23), 4296; https://doi.org/10.3390/nano12234296 - 3 Dec 2022

Cited by 2 | Viewed by 1561

Abstract

Plasmonic waveguides have been shown to be a promising approach to confine and transport electromagnetic energy beyond the diffraction limit. However, ohmic losses generally prevent their integration at micrometric or millimetric scales. Here, we present a gain-compensated plasmonic waveguide based on the integration [...] Read more.

Plasmonic waveguides have been shown to be a promising approach to confine and transport electromagnetic energy beyond the diffraction limit. However, ohmic losses generally prevent their integration at micrometric or millimetric scales. Here, we present a gain-compensated plasmonic waveguide based on the integration of linear chains of Ag nanoparticles on an optically active Nd³⁺-doped solid-state gain medium. By means of dual confocal fluorescence microscopy, we demonstrate long-range optical energy propagation due to the near-field coupling between the plasmonic nanostructures and the Nd³⁺ ions. The subwavelength fluorescence guiding is monitored at distances of around 100 µm from the excitation source for two different emission ranges centered at around 900 nm and 1080 nm. In both cases, the guided fluorescence exhibits a strong polarization dependence, consistent with the polarization behavior of the plasmon resonance supported by the chain. The experimental results are interpreted through numerical simulations in quasi-infinite long chains, which corroborate the propagation features of the Ag nanoparticle chains at both excitation (λ_exc = 590 nm) and emission wavelengths. The obtained results exceed by an order of magnitude that of previous reports on electromagnetic energy transport using linear plasmonic chains. The work points out the potential of combining Ag nanoparticle chains with a small interparticle distance (~2 nm) with rare-earth-based optical gain media as ultra-long-range waveguides with extreme light confinement. The results offer new perspectives for the design of integrated hybrid plasmonic–photonic circuits based on rare-earth-activated solid-state platforms. Full article

(This article belongs to the Special Issue Nano-Optics and Nano-Optoelectronics: Challenges and Future Trends)

► Show Figures

Figure 1

11 pages, 1959 KiB

Open AccessEditor’s ChoiceArticle

Dynamic Light Scattering Plus Scanning Electron Microscopy: Usefulness and Limitations of a Simplified Estimation of Nanocellulose Dimensions

by Quim Tarrés, Roberto Aguado, Justin O. Zoppe, Pere Mutjé, Núria Fiol and Marc Delgado-Aguilar

Nanomaterials 2022, 12(23), 4288; https://doi.org/10.3390/nano12234288 - 2 Dec 2022

Cited by 10 | Viewed by 2629

Abstract

Measurements of nanocellulose size usually demand very high-resolution techniques and tedious image processing, mainly in what pertains to the length of nanofibers. Aiming to ease the process, this work assesses a relatively simple method to estimate the dimensions of nanocellulose particles with an [...] Read more.

Measurements of nanocellulose size usually demand very high-resolution techniques and tedious image processing, mainly in what pertains to the length of nanofibers. Aiming to ease the process, this work assesses a relatively simple method to estimate the dimensions of nanocellulose particles with an aspect ratio greater than 1. Nanocellulose suspensions, both as nanofibers and as nanocrystals, are subjected to dynamic light scattering (DLS) and to field-emission scanning electron microscopy (FE-SEM). The former provides the hydrodynamic diameter, as long as the scatter angle and the consistency are adequate. Assays with different angles and concentrations compel us to recommend forward scattering (12.8°) and concentrations around 0.05–0.10 wt %. Then, FE-SEM with magnifications of ×5000–×20,000 generally suffices to obtain an acceptable approximation for the actual diameter, at least for bundles. Finally, length can be estimated by a simple geometric relationship. Regardless of whether they are collected from FE-SEM or DLS, size distributions are generally skewed to lower diameters. Width distributions from FE-SEM, in particular, are well fitted to log-normal functions. Overall, while this method is not valid for the thinnest fibrils or for single, small nanocrystals, it can be useful in lieu of very high-resolution techniques. Full article

(This article belongs to the Special Issue Cellulose Nanomaterials and Nanocomposites)

► Show Figures

Graphical abstract

11 pages, 2277 KiB

Open AccessEditor’s ChoiceArticle

Analysis of Electrochemical Performance with Dispersion Degree of CNTs in Electrode According to Ultrasonication Process and Slurry Viscosity for Lithium-Ion Battery

by Jaehong Choi, Chaewon Lee, Sungwoo Park, Tom James Embleton, Kyungmok Ko, Mina Jo, Kashif Saleem Saqib, Jeongsik Yun, Minki Jo, Yoonkook Son and Pilgun Oh

Nanomaterials 2022, 12(23), 4271; https://doi.org/10.3390/nano12234271 - 1 Dec 2022

Cited by 6 | Viewed by 3650

Abstract

Lithium-ion batteries (LIBs) continue to dominate the battery market with their efficient energy storage abilities and their ongoing development. However, at high charge/discharge C-rates their electrochemical performance decreases significantly. To improve the power density properties of LIBs, it is important to form a [...] Read more.

Lithium-ion batteries (LIBs) continue to dominate the battery market with their efficient energy storage abilities and their ongoing development. However, at high charge/discharge C-rates their electrochemical performance decreases significantly. To improve the power density properties of LIBs, it is important to form a uniform electron transfer network in the cathode electrode via the addition of conductive additives. Carbon nanotubes (CNTs) with high crystallinity, high electrical conductivity, and high aspect ratio properties have gathered significant interest as cathode electrode conductive additives. However, due to the high aggregational properties of CNTs, it is difficult to form a uniform network for electron transfer within the electrode. In this study, to help fabricate electrodes with well-dispersed CNTs, various electrodes were prepared by controlling (i) the mixing order of the conductive material, binder, and active material, and (ii) the sonication process of the CNTs/NMP solution before the electrode slurry preparation. When the binder was mixed with a well sonicated CNTs/NMP solution, the CNTs uniformly adsorbed to the then added cathode material of LiNi_0.6Co_0.2Mn_0.2O₂ and were well-dispersed to form a flowing uniform network. This electrode fabrication process achieved > 98.74% capacity retention after 50 cycles at 5C via suppressed polarization at high current densities and a more reversible H1-M phase transition of the active material. Our study presents a novel design benchmark for the fabricating of electrodes applying well-dispersed CNTs, which can facilitate the application of LIBs in high current density applications. Full article

(This article belongs to the Special Issue Advanced Functional Nanomaterials for Efficient Energy Conversion and Storage)

► Show Figures

Figure 1

12 pages, 2617 KiB

Open AccessEditor’s ChoiceArticle

Dual-Wavelength Forward-Enhanced Directional Scattering and Second Harmonic Enhancement in Open-Hole Silicon Nanoblock

by Xinghua Wang, Yunbao Zheng, Min Ouyang, Haihua Fan, Qiaofeng Dai and Haiying Liu

Nanomaterials 2022, 12(23), 4259; https://doi.org/10.3390/nano12234259 - 30 Nov 2022

Cited by 1 | Viewed by 1603

Abstract

Nanostructures with appropriate sizes can limit light-matter interaction and support electromagnetic multipole resonance. The interaction between light and nanostructures is intimately related to manipulating the direction of scattered light in the far field as well as the electromagnetic field in the near field. [...] Read more.

Nanostructures with appropriate sizes can limit light-matter interaction and support electromagnetic multipole resonance. The interaction between light and nanostructures is intimately related to manipulating the direction of scattered light in the far field as well as the electromagnetic field in the near field. In this paper, we demonstrate dual-wavelength directional forward-scattering enhancement in an individual open-hole silicon nanoblock (OH-SiNB) and simultaneously achieve bulk and surface electromagnetic field localization. The second harmonic generation is enhanced using electromagnetic field localization on the square hole surface. Numerical simulations reveal that the resonance modes, at λ₁ = 800 nm and λ₂ = 1190 nm, approximately satisfy the Kerker condition. In the near field, the magnetic dipole modes at dual wavelength all satisfy the boundary condition that the normal component of the electric displacement is continuous on the square holes surface, thus obtaining the surface electromagnetic field localization. Moreover, highly efficient second harmonic generation can be achieved at dual wavelengths using the surface electromagnetic field localization and the increased surface area of the square holes. Our results provide a new strategy for the integration of nanoantennas and nonlinear optoelectronic devices in optical chips. Full article

(This article belongs to the Section Nanophotonics Materials and Devices)

► Show Figures

Figure 1

9 pages, 3312 KiB

Open AccessEditor’s ChoiceArticle

Surface Oxidation of Cu₂O Nanoparticles by Adsorbed Ammonia

by Siwoo Lee, Ji Won Jang and Young Bok Ryu

Nanomaterials 2022, 12(23), 4242; https://doi.org/10.3390/nano12234242 - 29 Nov 2022

Viewed by 1671

Abstract

Copper-based nanoparticles have been intensively studied owing to their superior antibacterial activity. In this study, cuprous oxide (Cu₂O) nanoparticles were synthesized using two different methods. In particular, two methods for synthesizing copper oxide from NaOH, namely, with and without the addition [...] Read more.

Copper-based nanoparticles have been intensively studied owing to their superior antibacterial activity. In this study, cuprous oxide (Cu₂O) nanoparticles were synthesized using two different methods. In particular, two methods for synthesizing copper oxide from NaOH, namely, with and without the addition of NH₃, were used to adjust the morphology of the nanoparticles. The nanoparticles from the NH₃ and NaOH samples possessed an octahedral morphology. The crystal structure of the samples was confirmed by X-ray diffraction. The size distribution of the NH₃ sample was narrower than that of the NaOH sample. Furthermore, the average size of the NH₃ sample was smaller than that of the NaOH sample. Unexpectedly, the antibacterial activity of the NH₃ sample was found to be lower than that of the NaOH sample. X-ray photoelectron spectroscopy and Fourier-transform infrared spectroscopy revealed that the adsorbed NH₃ caused the surface oxidation of Cu₂O nanoparticles with azide (N₃) formation on surface. Full article

(This article belongs to the Section Biology and Medicines)

► Show Figures

Graphical abstract

17 pages, 15925 KiB

Open AccessEditor’s ChoiceArticle

Towards Wireless Detection of Surface Modification of Silicon Nanowires by an RF Approach

by Florian Requena, Samuel Ahoulou, Nicolas Barbot, Darine Kaddour, Jean-Marie Nedelec, Thierry Baron and Etienne Perret

Nanomaterials 2022, 12(23), 4237; https://doi.org/10.3390/nano12234237 - 28 Nov 2022

Cited by 3 | Viewed by 1274

Abstract

This paper shows the possibility to detect the presence of grafted molecules on the surface of silicon nanowires with a wireless RF radar approach based on the measurement of the backscattered signal of a resonant structure on which the nanowires are deposited. The [...] Read more.

This paper shows the possibility to detect the presence of grafted molecules on the surface of silicon nanowires with a wireless RF radar approach based on the measurement of the backscattered signal of a resonant structure on which the nanowires are deposited. The measured resonance frequency allows the determination of the intrinsic properties related to temperature and humidity variations, which can be related to the presence of the grafted molecules. Several functionalizations of nanowires have been realized and characterized. For the first time, an RF approach is used to detect significant differences related to the presence of grafted molecules on the surface of nanowires. In addition to detecting their presence, the obtained results show the potential of the radar approach to identify the type of functionalization of nanowires. A set of six different grafted molecules (including octadecyltrichlorosilane, ethynylpyrene, N3) was tested and correctly separated with the proposed approach. Various measurements of the same samples showed a good repeatability which made the approach compatible with the possibility of differentiating the molecules with each other by radar reading. Moreover, discussions about the application of such functionalizations are made to increase the sensibility of sensors using a radar approach. Full article

(This article belongs to the Special Issue Functional Nanomaterials for Sensing and Detection)

► Show Figures

Figure 1

15 pages, 8896 KiB

Open AccessEditor’s ChoiceArticle

On-Chip Reconfigurable and Ultracompact Silicon Waveguide Mode Converters Based on Nonvolatile Optical Phase Change Materials

by Yedeng Fei, Yin Xu, Dongmei Huang, Yue Dong, Bo Zhang, Yi Ni and P. K. A. Wai

Nanomaterials 2022, 12(23), 4225; https://doi.org/10.3390/nano12234225 - 28 Nov 2022

Cited by 5 | Viewed by 2229

Abstract

Reconfigurable mode converters are essential components in efficient higher-order mode sources for on-chip multimode applications. We propose an on-chip reconfigurable silicon waveguide mode conversion scheme based on the nonvolatile and low-loss optical phase change material antimony triselenide (Sb₂Se₃). The [...] Read more.

Reconfigurable mode converters are essential components in efficient higher-order mode sources for on-chip multimode applications. We propose an on-chip reconfigurable silicon waveguide mode conversion scheme based on the nonvolatile and low-loss optical phase change material antimony triselenide (Sb₂Se₃). The key mode conversion region is formed by embedding a tapered Sb₂Se₃ layer into the silicon waveguide along the propagation direction and further cladding with graphene and aluminum oxide layers as the microheater. The proposed device can achieve the TE₀-to-TE₁ mode conversion and reconfigurable conversion (no mode conversion) depending on the phase state of embedded Sb₂Se₃ layer, whereas such function could not be realized according to previous reports. The proposed device length is only 2.3 μm with conversion efficiency (CE) = 97.5%, insertion loss (IL) = 0.2 dB, and mode crosstalk (CT) = −20.5 dB. Furthermore, the proposed device scheme can be extended to achieve other reconfigurable higher-order mode conversions. We believe the proposed reconfigurable mode conversion scheme and related devices could serve as the fundamental building blocks to provide higher-order mode sources for on-chip multimode photonics. Full article

(This article belongs to the Section Nanophotonics Materials and Devices)

► Show Figures

Figure 1

13 pages, 3193 KiB

Open AccessEditor’s ChoiceArticle

Valorization of Sugarcane By-Products through Synthesis of Biogenic Amorphous Silica Microspheres for Sustainable Cosmetics

by Joana R. Costa, Ana Paula Capeto, Carla F. Pereira, Sílvia S. Pedrosa, Inês F. Mota, João da Silva Burgal, Ana I. Pintado, Manuela E. Pintado, Catarina S. S. Oliveira, Patrícia Costa and Ana Raquel Madureira

Nanomaterials 2022, 12(23), 4201; https://doi.org/10.3390/nano12234201 - 26 Nov 2022

Cited by 6 | Viewed by 2034

Abstract

Ashes from sugarcane by-product incineration were used to synthesize silica powders through alkaline hot extraction, followed by ethanol/acid precipitation or the sol–gel method. Both production methods allowed amorphous spherical silica microparticles with sizes ranging from 1–15 μm and 97% purity to be obtained. [...] Read more.

Ashes from sugarcane by-product incineration were used to synthesize silica powders through alkaline hot extraction, followed by ethanol/acid precipitation or the sol–gel method. Both production methods allowed amorphous spherical silica microparticles with sizes ranging from 1–15 μm and 97% purity to be obtained. Water absorption ranged from 135–155 mL/100 g and 150–250 mL/100 g for precipitated silica and silica gel, respectively, while oil absorption ranged from 305 to 390 and from 250 to 350 mL/100 g. The precipitation with ethanol allowed the recovery of 178 g silica/kg ash, with a lab process cost of EUR 28.95/kg, while the sol-gel process showed a yield of 198 g silica/kg ash with a cost of EUR 10.89/kg. The experimental data suggest that ash from sugarcane by-products is a promising source to be converted into a competitive value-added product, minimizing the environmental impact of disposal problems. Full article

(This article belongs to the Special Issue Micro and Nanomaterials in Cosmetics)

► Show Figures

Figure 1

16 pages, 4193 KiB

Open AccessFeature PaperEditor’s ChoiceArticle

Development and Characterisation of a Whole Hybrid Sol-Gel Optofluidic Platform for Biosensing Applications

by Emma MacHugh, Graceson Antony, Arun Kumar Mallik, Alicja Kaworek, Declan McCormack, Brendan Duffy and Mohamed Oubaha

Nanomaterials 2022, 12(23), 4192; https://doi.org/10.3390/nano12234192 - 25 Nov 2022

Cited by 3 | Viewed by 1705

Abstract

This work outlines, for the first time, the fabrication of a whole hybrid sol-gel optofluidic platform by integrating a microfluidic biosensor platform with optical waveguides employing a standard photolithography process. To demonstrate the suitability of this new hybrid sol-gel optofluidic platform, optical and [...] Read more.

This work outlines, for the first time, the fabrication of a whole hybrid sol-gel optofluidic platform by integrating a microfluidic biosensor platform with optical waveguides employing a standard photolithography process. To demonstrate the suitability of this new hybrid sol-gel optofluidic platform, optical and bio-sensing proof-of-concepts are proposed. A photoreactive hybrid sol-gel material composed of a photopolymerisable organically modified silicon alkoxide and a transition metal complex was prepared and used as the fabrication material for the entire optofluidic platform, including the optical waveguides, the sensing areas, and the microfluidic device. The most suitable sol-gel materials chosen for the fabrication of the cladding and core of the waveguides showed a RIC of 3.5 × 10⁻³ and gave thicknesses between 5.5 and 7 μm. The material was optimised to simultaneously meet the photoreactive properties required for the photolithography fabrication process and the optical properties needed for the effective optical operability of the microstructured waveguides at 532 and 633 nm with an integrated microfluidic device. The optical proof-of-concept was performed using a fluorescent dye (Atto 633) and recording its optical responses while irradiated with a suitable optical excitation. The biosensing capability of the platform was assessed using a polyclonal primary IgG mouse antibody and a fluorescent labelled secondary IgG anti-mouse antibody. A limit of detection (LOD) of 50 ug/mL was achieved. A correlation between the concentration of the dye and the emission fluorescence was evidenced, thus clearly demonstrating the feasibility of the proposed hybrid sol-gel optofluidic platform concept. The successful integration and operability of optical and microfluidic components in the same optofluidic platform is a novel concept, particularly where the sol-gel fabrication material is concerned. Full article

(This article belongs to the Special Issue Eco-Friendly Microdevice Printing Techniques with Functional Nano/Biomaterials)

► Show Figures

Graphical abstract

15 pages, 1589 KiB

Open AccessEditor’s ChoiceArticle

Effect of Silica-Based Nanomaterials on Seed Germination and Seedling Growth of Rice (Oryza sativa L.)

by Yaqi Jiang, Jie Yang, Mingshu Li, Yuanbo Li, Pingfan Zhou, Quanlong Wang, Yi Sun, Guikai Zhu, Qibin Wang, Peng Zhang, Yukui Rui and Iseult Lynch

Nanomaterials 2022, 12(23), 4160; https://doi.org/10.3390/nano12234160 - 24 Nov 2022

Cited by 12 | Viewed by 2561

Abstract

The application of nanomaterials (NMs) in agriculture has become a global concern in recent years. However, studies on their effects on plants are still limited. Here, we conducted a seed germination experiment for 5 days and a hydroponics experiment for 14 days to [...] Read more.

The application of nanomaterials (NMs) in agriculture has become a global concern in recent years. However, studies on their effects on plants are still limited. Here, we conducted a seed germination experiment for 5 days and a hydroponics experiment for 14 days to study the effects of silicon dioxide NMs(nSiO₂) and silicon carbide NMs(nSiC) (0,10, 50, 200 mg/L) on rice (Oryza sativa L.). Bulk SiO₂ (bSiO₂) and sodium silicate (Na₂SiO₃) were used as controls. The results showed that nSiO₂ and nSiC increased the shoot length (11–37%, 6–25%) and root length (17–87%, 59–207%) of germinating seeds, respectively, compared with the control. Similarly, inter-root exposure to nSiO₂, bSiO_2, and nSiC improved the activity of aboveground catalase (10–55%, 31–34%, and 13–51%) and increased the content of trace elements magnesium, copper, and zinc, thus promoting the photosynthesis of rice. However, Na₂SiO₃ at a concentration of 200 mg/L reduced the aboveground and root biomass of rice by 27–51% and 4–17%, respectively. This may be because excess silicon not only inhibited the activity of root antioxidant enzymes but also disrupted the balance of mineral elements. This finding provides a new basis for the effect of silica-based NMs promotion on seed germination and rice growth. Full article

► Show Figures

Graphical abstract

11 pages, 2068 KiB

Open AccessFeature PaperEditor’s ChoiceArticle

High-Reliability Perovskite Quantum Dots Using Atomic Layer Deposition Passivation for Novel Photonic Applications

by Tzu-Yi Lee, Tsau-Hua Hsieh, Wen-Chien Miao, Konthoujam James Singh, Yiming Li, Chang-Ching Tu, Fang-Chung Chen, Wen-Chung Lu and Hao-Chung Kuo

Nanomaterials 2022, 12(23), 4140; https://doi.org/10.3390/nano12234140 - 23 Nov 2022

Cited by 6 | Viewed by 2266

Abstract

In this study, we propose highly stable perovskite quantum dots (PQDs) coated with Al₂O₃ using atomic layer deposition (ALD) passivation technology. This passivation layer effectively protects the QDs from moisture infiltration and oxidation as well as from high temperatures and [...] Read more.

In this study, we propose highly stable perovskite quantum dots (PQDs) coated with Al₂O₃ using atomic layer deposition (ALD) passivation technology. This passivation layer effectively protects the QDs from moisture infiltration and oxidation as well as from high temperatures and any changes in the material characteristics. They exhibit excellent wavelength stability and reliability in terms of current variation tests, long-term light aging tests, and temperature/humidity tests (60°/90%). A white-light system has been fabricated by integrating a micro-LED and red phosphor exhibiting a high data transmission rate of 1 Gbit/s. These results suggest that PeQDs treated with ALD passivation protection offer promising prospects in full-color micro-displays and high-speed visible-light communication (VLC) applications. Full article

(This article belongs to the Special Issue Quantum Dots and Micro-LED Display 2.0)

► Show Figures

Figure 1

14 pages, 13242 KiB

Open AccessEditor’s ChoiceArticle

Mechanical Characterization of Two-Segment Free-Standing ZnO Nanowires Using Lateral Force Microscopy

by János Volk, János Radó, Zsófia Baji and Róbert Erdélyi

Nanomaterials 2022, 12(23), 4120; https://doi.org/10.3390/nano12234120 - 22 Nov 2022

Viewed by 1216

Abstract

Mechanical characterization of quasi one-dimensional nanostructures is essential for the design of novel nanoelectromechanical systems. However, the results obtained on basic mechanical quantities, such as Young’s modulus and fracture strength, show significant standard deviation in the literature. This is partly because of diversity [...] Read more.

Mechanical characterization of quasi one-dimensional nanostructures is essential for the design of novel nanoelectromechanical systems. However, the results obtained on basic mechanical quantities, such as Young’s modulus and fracture strength, show significant standard deviation in the literature. This is partly because of diversity in the quality of the nanowire, and partly because of inappropriately performed mechanical tests and simplified mechanical models. Here we present orientation-controlled bending and fracture studies on wet chemically grown vertical ZnO nanowires, using lateral force microscopy. The lateral force signal of the atomic force microscope was calibrated by a diamagnetic levitation spring system. By acquiring the bending curves of 14 nanowires, and applying a two-segment mechanical model, an average bending modulus of 108 ± 17 GPa was obtained, which was 23% lower than the Young’s modulus of bulk ZnO in the [0001] direction. It was also found that the average fracture strain and stress inside the nanowire was above 3.1 ± 0.3 % and 3.3 ± 0.3 GPa, respectively. However, the fracture of the nanowires was governed by the quality of the nanowire/substrate interface. The demonstrated technique is a relatively simple and productive way for the accurate mechanical characterization of vertical nanowire arrays. Full article

(This article belongs to the Special Issue Low-Dimensional Semiconductor Materials: Fabrication, Characterization and Applications)

► Show Figures

Graphical abstract

12 pages, 3085 KiB

Open AccessEditor’s ChoiceArticle

Ethanol Electrooxidation at 1–2 nm AuPd Nanoparticles

by Juliette W. Strasser and Richard M. Crooks

Nanomaterials 2022, 12(22), 4093; https://doi.org/10.3390/nano12224093 - 21 Nov 2022

Cited by 2 | Viewed by 1307

Abstract

We report a systematic study of the electrocatalytic properties and stability of a series of 1–2 nm Au, Pd, and AuPd alloy nanoparticles (NPs) for the ethanol oxidation reaction (EOR). Following EOR electrocatalysis, NP sizes and compositions were characterized using aberration-corrected scanning transmission [...] Read more.

We report a systematic study of the electrocatalytic properties and stability of a series of 1–2 nm Au, Pd, and AuPd alloy nanoparticles (NPs) for the ethanol oxidation reaction (EOR). Following EOR electrocatalysis, NP sizes and compositions were characterized using aberration-corrected scanning transmission electron microscopy (ac-STEM) and energy dispersive spectroscopy (EDS). Two main findings emerge from this study. First, alloyed AuPd NPs exhibit enhanced electrocatalytic EOR activity compared to either monometallic Au or Pd NPs. Specifically, NPs having a 3:1 ratio of Au:Pd exhibit an ~8-fold increase in peak current density compared to Pd NPs, with an onset potential shifted ~200 mV more to the negative compared to Au NPs. Second, the size and composition of AuPd alloy NPs do not (within experimental error) change following 1.0 or 2.0 h chronoamperometry experiments, while monometallic Au NPs increase in size from 2 to 5 nm under the same conditions. Notably, this report demonstrates the importance of post-catalytic ac-STEM/EDS characterization for fully evaluating NP activity and stability, especially for 1–2 nm NPs that may change in size or structure during electrocatalysis. Full article

(This article belongs to the Special Issue Nanomaterials and Nanotechnology for Electrocatalytic Applications)

► Show Figures

Figure 1

17 pages, 4515 KiB

Open AccessEditor’s ChoiceArticle

Cascade Förster Resonance Energy Transfer Studies for Enhancement of Light Harvesting on Dye-Sensitized Solar Cells

by Mulugeta Tesema Efa, Jheng-Chang Huang and Toyoko Imae

Nanomaterials 2022, 12(22), 4085; https://doi.org/10.3390/nano12224085 - 20 Nov 2022

Cited by 3 | Viewed by 1708

Abstract

This work reports cascade Förster resonance energy transfer (FRET)-based n-type (ZnO) and p-type (NiO) dye-sensitized solar cells (DSSCs), discussing approaches to enhance their overall performance. Although DSSCs suffer from poorer performance than other solar cells, the use of composites with carbon dot (Cdot) [...] Read more.

This work reports cascade Förster resonance energy transfer (FRET)-based n-type (ZnO) and p-type (NiO) dye-sensitized solar cells (DSSCs), discussing approaches to enhance their overall performance. Although DSSCs suffer from poorer performance than other solar cells, the use of composites with carbon dot (Cdot) can enhance the power conversion efficiency (PCE) of DSSCs. However, further improvements are demanded through molecular design to stimulate DSSCs. Here, a photosensitized system based on a cascade FRET was induced alongside the conventional photosensitizer dye (N719). To N719 in a DSSC is transferred the energy cascaded through donor fluorescence materials (pyrene, 3-acetyl-7-N,N-diethyl-coumarin or coumarin and acridine orange), and this process enhances the light-harvesting properties of the sensitizers in the DSSC across a broad region of the solar spectrum. PCE values of 10.7 and 11.3% were achieved for ZnO/Cdot and NiO/Cdot DSSCs, respectively. These high PCE values result from the energy transfer among multi-photosensitizers (cascade FRET fluorophores, N719, and Cdot). Moreover, Cdot can play a role in intensifying the adsorption of dyes and discouraging charge recombination on the semiconductor. The present results raise expectations that a significant improvement in photovoltaic performance can be attained of DSSCs exploiting the cascade FRET photonics phenomenon. Full article

(This article belongs to the Special Issue Quantum Materials for Photonic Devices)

► Show Figures

Graphical abstract

Journal Menu

Journal Browser

Editor’s Choice Articles

Article

Further Information

Guidelines

MDPI Initiatives

Follow MDPI