51 Results Found

Ni-Cr-Si-Fe-B self-fluxing alloys are commonly used in hardfacing applications; in addition, they are subjected to conditions of wear, corrosion, and high temperatures, but are not used in casting applications. In this work, gravity casting is presen...

The spheroidization behavior of the nano-primary silicon phase induced by Nd under high-current pulsed electron beam (HCPEB) irradiation was investigated in this study. The study results revealed that, compared to the Al–17.5Si alloy, spheroidi...

In this study, a WC-reinforced Ni-based surfacing layer was prepared on Q235 steel plate by plasma arc welding. The effects of nano-Y2O3 with different contents (0 wt.%, 0.4 wt.%, 0.8 wt.%, 1.2 wt.%, and 1.6 wt.%) on the microstructure, phase composi...

The plasma sprayed Fe-based Ni/WC composite coating on the surface of 45 steel was post-treated by laser remelting with the addition of nano-SiC. The effect of laser power on the interface microstructure of a laser remelting nano-SiC modified Fe-base...

In the present work, nano Cu (0, 5, 10, 15, 20, 25 wt.%) was added to W, and W–Cu composites were fabricated using the spark plasma sintering (S.P.S.) technique. The densification, microstructural evolution, tensile strength, micro-hardness, and elec...

A detailed study was carried out to gain a better understanding of the microstructural differences between Ti-6Al-4V parts fabricated via the conventional powder metallurgy (PM) and the laser powder bed fusion (L-PBF) 3D printing routes. The parts we...

Nano Cu precipitation plays a crucial role in significantly improving the performance of the Cu-bearing high-strength low-alloy steel. The final cooling temperature effects the transformation products of austenite during the continuous cooling proces...

This work aims to define the microstructure and to study the mechanical properties of an Al matrix incorporated with various amounts of Fe2O3 (3, 6, 9, 12 and 15 wt.%) with a constant amount of Ag at 1 wt.%. Al/Fe2O3 + Ag hybrid nano-composite sample...

This work investigates the mechanisms of the microstructure evolution in the melted surface layers of a WC-6% Co hard alloy when increasing the number of pulses of irradiation by high-current pulsed electron beam (HCPEB) treatment. After one pulse of...

The non-heat-treated, die-cast aluminum alloy samples were prepared meticulously via die-casting technology. The crystal structure, microstructure, and phase composition of the samples were comprehensively studied through electron backscatter diffrac...

The Al–Mn alloy heat exchanger fin production process includes a brazing treatment at s high temperature of 600 °C, in which coarse grains are preferred for their high resistance to deformation at elevated temperatures by decreasing the gra...

In Fe-Mn-Al-Ni shape memory alloys, the stabilization of superelasticity would be affected by the undesired precipitation of B2 nano-particles during natural aging. In order to solve this problem, the effect of Mo alloying on the precipitation behavi...

This study aimed to evaluate the incorporation of zirconia/silver phosphate nanoparticles to develop experimental dental adhesives and to measure their physical and mechanical properties. The nanoparticles were synthesized by the sonication method, a...

Nano-carbon reinforced titanium matrix/hydroxyapatite (HA) biocomposites were successfully prepared by spark plasma sintering (SPS). The microstructure, mechanical properties, biocompatibility, and the relationship between microstructure and properti...

Biomaterial composites made of titanium and hydroxyapatite (HA) powder are among the most important biomedicalmaterials due to their good mechanical properties and biocompatibility. In this work, graphene-reinforced titanium matrix/nano-hydroxyapatit...

In this study, the addition of the rare earth oxide CeO2 was investigated to alter the microstructural properties of the nano-WC-reinforced Ni-based composite coatings. The reinforced composite was prepared on the 42CrMo steel surface using a semicon...

A systematic study of explosively welded tantalum and 304 L stainless steel clad with M1E copper interlayer was carried out to characterize the microstructure and mechanical properties of interfacial layers. Microstructures were examined using transm...

This work explores the surface protection against wear provided by electroplated metal matrix composite coatings containing hard and lubricant particles. The second phase mix was selected to provide wear resistance by hardening the material and decre...

Gravitational melt-stir casting produced hybrid nano-reinforcements (β-SiCp) and micro-reinforcements (Bi and Sb) of AZ91 composites. SiCp-diffused discontinuous β-Mg17Al12 precipitation with a vital factor of SiC was exhibited at the grain boundary...

Post-treatment is crucial to improve the comprehensive performance of laser-cladded martensitic stainless steel coatings. In this work, a low-temperature tempering treatment (210 °C), for the first time, was performed on the laser-cladded AISI 42...

Protective coatings are essential for extending the service life of components exposed to harsh conditions, such as pipes used in industrial systems, where wear and corrosion remain constant challenges. This study explores the development of a nano-s...

In the present work, TiC/TiB2/Al composite coatings were synthesized onto a precipitation hardened AlSi1MgMn alloy by laser surface alloying (LSA), using 13.3 J/mm2 and 20 J/mm2 laser energy densities. Microstructure evaluation, microhardness, wear a...

The high-Mg-content Al-Mg-Zn-Si alloy, as a novel aluminum alloy, exhibits excellent strength, toughness, and corrosion resistance, demonstrating significant application potential in lightweight structural components for aerospace, weapon systems, ra...

Titanium- and chromium-based carbides are attractive coating materials to impart wear resistance. Suspension plasma spraying (SPS) is a relatively new thermal spray process which has shown a facile ability to use sub-micron and nano-sized feedstock t...

The uneven distribution and large size of the second phase weakens the effect of dispersion strengthening in ODS-W alloys. In this article, the W-Al2O3 composite powders were fabricated using a wet chemical method, resulting in a finer powder and uni...

In this paper, a nanocrystalline surface layer without impurities was fabricated on Ti-6Al-4V alloy by means of surface mechanical attrition treatment (SMAT). The grain size in the nanocrystalline layer is about 10 nm and grain morphology displays a...

Nanomaterials are usually associated with modern technologies and advanced processing methods. Three silver Dacian bracelets within Cehei hoard (Salaj County, Romania) are tougher than they should be according to the apparently higher silver content....

Friction stir processing is a novel solid-state process to modify microstructures and their properties by intense, localized plastic deformation. However, little research has been reported for microstructure evolutions of advanced high-strength steel...

In this study, metallic elements that have limited/negligible solubility in pure magnesium (Mg) were incorporated in Mg using the disintegrated melt deposition technique. The metallic elements added include: (i) micron sized titanium (Ti) particulate...

The effects of extrusion temperatures on the microstructure, mechanical properties, and corrosion performance of biomedical Mg-1Zn-0.4Ca-1MgO composites were systematically investigated. The results indicated that lower extrusion temperatures notably...

Nickel-based alloys are considered promising materials for primary circuits of high-temperature gas reactors (HTGRs), specifically for gas turbines. The primary helium (He) coolant in the gas-turbine-based HTGRs is expected to reach temperatures of u...

This article describes spark plasma sintering of ceramics based on silicon carbide with nanoadditives, as follows: MnOnano 5.5 wt. % + Al2O3nano 2.0 wt. % + SiCnm (37–57 wt. %) + SiCµm (31–51 wt. %) + SiO2µm 4.5 wt. %. Sinteri...

With the use of electrolytic Cu powder, Zr powder, Si powder and nickel-coated B4C powder as cladding powders, in-situ synthesized ZrB2-SiC reinforced copper matrix composite coatings were prepared by laser cladding on the surface of the copper subst...

This paper deals with the Cr-CrN-(Cr0.35Ti0.40Al0.25)N coating. It has a three-layered architecture with a nano-structured wear-resistant layer. The studies involved the investigation into the microstructure (with the use of SEM and TEM), elemental a...

TiC-reinforced metal matrix composites were fabricated by laser cladding and FeCrCoNiAlTiC high entropy alloy powder. The heat of the laser formed a TiC phase, which was consistent with the thermodynamic calculation, and produced a coating layer with...

Two Ni-AlSi12 coatings were prepared using mechanical alloying (MA) and mechanical alloying followed by laser cladding (LC), respectively. Phase composition and microstructure variations caused by powder weight ratio and laser-specific energy were th...

The evolution of microstructure, phase composition and physico-mechanical properties of the biocompatible Ti-39Nb-7Zr alloy (wt.%) after severe plastic deformation by rotary forging (RF) was studied using various methods including light optical micro...

Rare earth elements have been widely utilized in material manufacturing to enhance properties in various ways. In order to obtain the WC-10Co4Cr coating with uniform distribution of rare earths, CeO2-modified powder was prepared by mixing 1 wt.% nano...

In this study, a nano-composite material of a nanostructured Al-based matrix reinforced with Fe40Al intermetallic particles was produced by ball milling. During the non-equilibria processing, the powder mixtures with the compositions of Al-XFe40Al (X...

TIG arc additive manufacturing experiments were performed utilizing TiB2 nanoparticle-reinforced toward to 7075 aluminum alloy welding wire, and the microstructure and mechanical properties corresponding to different locations of welding plate were i...

Due to their excellent mechanical properties and large specific surface area, graphene and its derivatives are widely used in metal matrix composites as reinforcements. In this study, the thermal reduction behavior of large-size graphene oxide are in...

Austenitic stainless steels produced by laser powder bed fusion (L-PBF) are quite interesting materials owing to their specific microstructure consisting of dendrite walls built of dislocations pinned by many nano-oxides that involves significant str...

The research presented in this paper is part of a larger project concerning high-manganese alloys with different chemical compositions (mainly in manganese content from 21 to 31 wt.%). The presented examination results concern the analysis of the mic...

Background: Conventional sintering methods of dental ceramics have limitations of high temperature and slow cooling rates with requirements of additional heat treatment for crystallization. Spark plasma sintering (SPS) is an emerging technique that h...

In the most recent decades the introduction of unconventional machining processes allowed the development of micromachining techniques. In this work, the influence of material microstructures on the micromilling process was investigated. Ti6Al4V allo...

Diamond/copper composite coating is promising for wear-resistant applications, owing to the extreme hardness of the diamond reinforcement. Ti-coated diamond/copper composite coatings with various laser powers were successfully fabricated employing th...

This study investigates the effect of duo-ceramic zirconia and silicon nitride (ZrO2-Si3N4) particles and their reinforcement proficiencies on a Ti6Al4V alloy, consolidated using the spark plasma sintering (SPS) technique. The selected sintering para...

Magnesium-zinc-calcium (Mg-Zn-Ca) alloys as a biomaterial have attracted much attention recently, owing to their excellent biocompatibility, similar mechanical properties to natural bone, and biodegradable properties. Despite the numerous advantages...

Production of high-quality maraging steel is dependent not only on the production technology but also on the alloying design and heat treatment. In this work, cobalt-free, low nickel, molybdenum-containing maraging steel was produced by melting the r...

A new surface strengthening process: Plasma surface chromizing was implemented on the metallic card clothing to improve its wear resistance based on double glow plasma surface metallurgy technology. A chromizing coating was prepared in the process, w...