In this paper, the microstructure of friction stir welded between the Al–Li–Cu alloy and the Al–Zn–Mg–Cu alloy was studied using optical microscope(OM), electronic backscattered diffraction (EBSD), SEM, and TEM. The hard...
An Al-Zn-Mg-Cu alloy has high specific strength, good corrosion resistance, fracture toughness and fatigue resistance. It is one of the most important structural materials in the fields of aviation, aerospace, weapons and transportation; in particula...
High zinc containing Al-Zn-Mg-Cu is the research focus of ultra-high strength aluminum alloy. In the present paper, the Al-Zn-Mg-Cu multi-component system is studied when the content of Zn is 10.5 wt.%, 11 wt.% and 12 wt.%, respectively. The vertical...
In this paper, the refinement effect of Al-5Ti-0.2C refiner on Al-Zn-Mg-Cu alloys was first investigated, and then the effects of three forming processes, i.e., Gravity Casting (GC), Squeeze Casting (SC), and Squeeze Casting after Ultrasonic Treatmen...
The application of high-strength Al-Zn-Mg-Cu alloy is seriously limited because of its poor formability. A novel electroshock treatment (EST) technique with low frequency combined with tensile deformation was proposed to address the issues of low pla...
Al-Zn-Mg-Cu alloys are widely used in aircraft applications because of their superior mechanical properties and strength/weight ratios. Commercial Al-Zn-Mg-Cu alloys have been intensively studied over the last few decades. However, well-considered th...
Natural aging reduces the cost of alloy manufacturing while saving input energy but takes too long to complete for most Al-Zn-Mg-Cu alloys. Research has proved that nano-treating can facilitate precipitation in heat-treatable alloys. In this study, n...
In this paper, hot rolling pre-deformation treatment was applied to an Al-Zn-Mg-Cu alloy after solid solution treatment, followed by peak aging treatment. The effect of the degree of deformation was discussed. The microstructure of the alloy after tr...
Al-Zn-Mg-Cu alloy, recognized for its heat-treatable and super-high strength, is a pivotal material for critical structural components in aviation. Consequently, grasping the intricate relationship between heat treatment processes and the microstruct...
The effects of (Zn + Mg) total content (9.6–11.7 wt.%) combined with multi-directional forging (MDF) on the microstructure and properties of high-strength Al–Zn–Mg–Cu alloys were systematically investigated. Our results demons...
Aluminum Alloy AA-7034 is a high strength wrought alloy with reasonable ductility containing 10–12 wt% Zn, 2–3 wt% Mg, and 0.8–1.2 wt% Cu. This work investigates the effect of varying the concentration of Zn (10–12 wt%) and Cu (0.8–1 wt%) on the solu...
This study explores the influence of multiple remelting and repeated T6 heat treatment on the microstructure and mechanical properties of Al-Zn-Mg-Cu alloys. With the increase in remelting cycles, the alloy experiences structural alterations due to r...
In this study, the feed-forward (FF) neural networks (NNs) with back-propagation (BP) learning algorithm is used to estimate the ultimate tensile strength of unrefined Al-Zn-Mg-Cu alloys and refined the alloys by Al-5Ti-1B and Al-5Zr master alloys....
Spray forming is a manufacturing process that enables the production of high-performance metallic materials with exceptional properties. Due to its rapid solidification nature, spray forming can produce materials that exhibit fine, uniform, and equia...
Contact solution treatment (CST) of Al–Zn–Mg–Cu alloys can shorten solution time to within 40 s in comparison with 1800 s with traditional solution treatment using a heating furnace. Heating temperature is the key factor in solution treatment. Consid...
In this work, Al-Zn-Mg-Cu powders containing 0.15 and 0.33 wt % oxygen were utilized to prepare high-strength aluminum alloys through the process of cold isostatic pressing, sintering, hot extrusion, and heat treatment. Microstructural and mechanical...
The recrystallization and intergranular corrosion behaviors impacted by the additions of Sc and Zr in Al-Zn-Mg-Cu alloys are investigated. The stronger effect of coherent Al3(Sc1−xZrx) phases on pinning dislocation resulted in a lower degree of recry...
Al–Zn–Mg–Cu alloys are well known for their outstanding strength, toughness, and corrosion resistance, arising from the balanced addition of Mg, Zn, and Cu. However, conventional casting methods often lead to grain boundary segregat...
Extruded Al-Zn-Mg-Cu alloy samples with grains aligned parallel to the extrusion direction were subjected to high-pressure annealing. The effects of annealing pressure on the microstructure, hardness, and corrosion properties (evaluated using potenti...
Effects of temperature and strain rate on the fracture behaviors of an Al-Zn-Mg-Cu alloy are investigated by isothermal uniaxial tensile experiments at a wide range of temperatures and strain rates, from room temperature (RT) to 400 °C and from 1...
The Zr element is one of the important grain refiners for 7xxx series Al-Zn-Mg-Cu alloys, but the effect of Zr content more than 0.15 wt.% needs to be deeply investigated under the action of ultrasonic vibration. In this study, the effects of Zr cont...
Microstructure is a significant factor that influences the mechanical properties of alloys. The effect of multiaxial forging (MAF) and subsequent aging treatment on the precipitated phases of Al-Zn-Mg-Cu alloy remains unclear. Therefore, an Al-Zn-Mg-...
High-temperature tensile tests were developed to explore the flow features of an Al-Zn-Mg-Cu alloy. The fracture characteristics and microstructural evolution mechanisms were thoroughly revealed. The results demonstrated that both intergranular fract...
The presence of Al7Cu2Fe particles, formed due to Fe impurities in Al-Zn-Mg-Cu alloys, significantly impacts mechanical properties and formability, which is crucial for the use of these alloys in the automotive and aerospace industries. In this study...
High temperature tensile properties and long-term thermal stability play an important role in practical applications of Al-Zn-Mg-Cu alloys. In order to evaluate the effect of Er addition on the properties of an Al-Zn-Mg-Cu alloy as potential high tem...
Although heat-treatable Al-Zn-Mg-Cu alloys are widely used in aerospace industries, distortion and cracks exist due to the residual stress during quenching. Understanding the flow stress behavior and numerically modeling the process is the key to pre...
Transition element microalloying is important for improving the properties of Al-Zn-Mg-Cu alloys. Nevertheless, along with its high costs, increasing Sc content generates a harmful phase, limiting the strength of the alloy. In this experiment, we red...
It is well known that the development of lightweight alloys with improved comprehensive performance and application value are the future development directions for the ultra-high-strength 7xxx series Al-Zn-Mg-Cu alloys used in the aircraft field. As...
The hot deformation behavior of an Al-Zn-Mg-Cu alloy was investigated by hot compression test at deformation temperatures varying from 320 to 440 °C with strain rates ranging from 0.01 to 10 s−1. The results show that the Mg(Zn, Cu)2 particles as a r...
The effect of over-aging on the precipitation behavior and mechanical properties of an ultra-high-strength Al-Zn-Mg-Cu alloy was investigated using various over-aging treatment regimes. To reveal the influence of over-aging on matrix precipitation, n...
Recent advances in the leisure boat industry have spurred demand for improved materials for propeller manufacturing, particularly high-strength aluminum alloys. While traditional Al-Si alloys like A356 are commonly used due to their excellent castabi...
The microstructural evolution of the Al–Zn–Mg–Cu alloy during the superplastic deformation process has been studied by high temperature tensile experiment. The superplastic deformation behaviors are investigated under different temp...
The effects of nanoprecipitations on the mechanical properties of Al-Zn-Mg-Cu alloys after GBF (gas bubbling filtration) and EMS (electromagnetic stirring) casting were investigated. Dendritic cell structures were formed after GBF processing, while g...
Herein, composite extrusion deformation and heat treatment process at various temperatures were studied on a new type of Al-Zn-Mg-Cu alloy billet. The influence of pre-deformation and the final forming of extrusion and heat treatment of annular chann...
Deformation and heat treatment are important means to strengthen aluminum alloys. However, the influence mechanism of pre-strain on aging precipitation kinetics and its effect on mechanical properties are still not clear. In this work, uniaxial isoth...
In this study, Al-Zn-Mg-Cu alloy was refill friction spot welded, and the precipitates, dislocation, recovery, and recrystallization characteristics were focused. In the stir zone (SZ), continues dynamic recrystallization occurs under the intense pla...
The 7085 aluminum alloy with a low Cu content is an important lightweight structural material in the aerospace field due to its advantages of low density, high specific strength, and high hardenability. However, like other high-strength Al-Zn-Mg-Cu a...
In this study, large-sized Al–Zn–Mg–Cu alloy billets were prepared by direct chill casting imposed with annular electromagnetic stirring and intercooling; a process named uniform direct chill casting. The effects of uniform direct chill casting on gr...
The creep aging behaviors of retrogressed Al-Zn-Mg-Cu alloy were studied by uniaxial tensile creep tests at 140 °C. The effects of creep aging time and applied stress on microstructures and properties of the studied alloy were investigated by using t...
The study presents the results of research on the influence of different contents of main alloying additions, such as Mg (2 ÷ 2.5 wt.%), Cu (1.2 ÷ 1.9 wt.%), and Zn (5.5 ÷ 8 wt.%), on the strength properties and plasticity of sel...
Al-Zn-Mg-Cu aluminum alloys have the advantages of high specific strength, easy processing, and high toughness, showing great potential application in the aerospace field. However, ultra-high strength aluminum alloys usually contain coarse microstruc...
The hot deformation behavior of Al-Zn-Mg-Cu alloy was investigated by flow stress curves in isothermal hot compression experiments with deformation temperatures of 350–450 °C and strain rates of 0.01 s−1 to 1 s−1, and the consti...
The fabricated Al–Zn–Mg–Cu alloy build has low mechanical properties due to the dissolution of strengthening precipitates back into the matrix during friction stir additive manufacturing (FSAM). Post-fabricated aging was considered...
The hot deformation behavior and microstructural evolution of an Al-Zn-Mg-Cu (7150) alloy was studied during hot compression at various temperatures (300 to 450 °C) and strain rates (0.001 to 10 s−1). A decline ratio map of flow stresses was proposed...
Fine-grained (average gain size 3.8 μm) and coarse-grained (average gain size 24.9 μm) Al-Zn-Mg-Cu alloys were subjected to isothermal compression at 10−3 s−1 and temperature ranges from 300 °C to 450 °C. The grain structure...
Thermomechanical treatment is an effective way to refine the coarse microstructures of aluminum alloys. In this work, multiaxial forging deformation at high, medium, and cryogenic temperatures (i.e., 450, 250, and −180 °C, respectively) was...
In this study, Al, Zn, Mg and Cu elemental metal powders were chosen as the raw powders. The nanocrystalline Al-7Zn-2.5Mg-2.5Cu bulk alloy was prepared by mechanical alloying and spark plasma sintering. The effect of milling time on the morphology an...
In the present study, after solid solution treatment, four different artificial aging treatments (100, 120, 140 and 160 °C) were performed on Al-5.98Zn-2.86Mg-1.61Cu (wt.%) alloy, denoted as 7075-LCu, and Al-5.91Zn-2.83Mg-1.98Cu (wt.%) alloy, den...
In order to obtain fine grained structure efficiently, a new multi-step rolling process (MSR: pre-deformation + intermediate annealing + hot deformation) was applied in Al-Zn-Mg-Cu plates. Conventional hot rolling (CHR) was also carried out as a cont...
Friction stir additive manufacturing (FSAM) can be potentially used for fabricating high-performance components owing to its advantages of solid-state processing. However, the inhomogeneous microstructures and mechanical properties of the build attri...
of 15