Skip to Content

8 Results Found

  • Article
  • Open Access
13 Citations
3,338 Views
26 Pages

19 November 2020

In this study, an experimental and statistic investigation approach based on analysis of variance (ANOVA) and response surface methodology (RSM) techniques was performed to find the significant main effects and two-factor interaction effects and to d...

(This article belongs to the Section Manufacturing Processes and Systems)
  • Article
  • Open Access
1 Citations
787 Views
15 Pages

Tool Wear and Surface Finish in AISI 304 Stainless Steel Dry Turning with Cermet Inserts

  • Laurence Colares Magalhães,
  • Nelson Antenor Sorte,
  • Marcelo Tramontin Souza and
  • Armando Marques

23 March 2026

The present study investigates the surface integrity and flank wear of uncoated cermet inserts during dry turning of AISI 304 stainless steel. Three-dimensional metrology techniques were employed to assess both surface roughness and cutting-tool flan...

(This article belongs to the Section Metals and Alloys)
  • Article
  • Open Access
1 Citations
1,431 Views
20 Pages

Influence of Chip Breaker Geometric Shape on the Cutting Performance of Cermet Tools

  • Shuwen Yu,
  • Zengmin Shi,
  • Chengui Deng-Li,
  • Junwen Gao and
  • Lei Dai

9 March 2026

Ti(C,N)-based cermet turning inserts with two distinct chip breaker groove structures were employed to investigate the influence of chip breaker geometry on cutting performance. Chip removal performance and wear resistance of the inserts were evaluat...

(This article belongs to the Section Materials Engineering)
  • Article
  • Open Access
18 Citations
4,408 Views
16 Pages

Tool Wear Effect on Surface Integrity in AISI 1045 Steel Dry Turning

  • Laurence Colares Magalhães,
  • Gabriel Catarino Carlesso,
  • Luis Norberto López de Lacalle,
  • Marcelo Tramontin Souza and ,
  • Fabiana de Oliveira Palheta and
  • Cristiano Binder
  • + 1 author+ 0 author

9 March 2022

In the present work, the surface integrity and flank wear of uncoated cermet inserts in dry turning of AISI 1045 steel were evaluated. Three-dimensional techniques were used to assess the surface roughness. Previously, finite element analysis was car...

(This article belongs to the Special Issue Machining and Surface Properties of Steel Parts)
  • Review
  • Open Access
50 Citations
10,408 Views
52 Pages

A Critical Review of High-Temperature Tribology and Cutting Performance of Cermet and Ceramic Tool Materials

  • Ali Elgazzar,
  • Sheng-Jian Zhou,
  • Jia-Hu Ouyang,
  • Zhan-Guo Liu and ,
  • Yu-Jin Wang and
  • Ya-Ming Wang
  • + 1 author+ 0 author

Cermet materials exhibit advanced mechanical and tribological properties, and are widely used for tribology, elevated temperature, and machining applications due to their unique amalgamation of hardness, strength, and toughness. This paper presents a...

(This article belongs to the Special Issue Recent Advances in High Temperature Tribology)
  • Article
  • Open Access
15 Citations
5,901 Views
14 Pages

Selection of Machining Parameters Using a Correlative Study of Cutting Tool Wear in High-Speed Turning of AISI 1045 Steel

  • Luis Wilfredo Hernández González,
  • Yassmin Seid Ahmed,
  • Roberto Pérez Rodríguez,
  • Patricia Del Carmen Zambrano Robledo and
  • Martha Patricia Guerrero Mata

The manufacturing industry aims to produce many high quality products efficiently at low cost, thereby motivating companies to use advanced manufacturing technologies. The use of high-speed machining is increasingly widespread; however, it lacks a de...

(This article belongs to the Special Issue Smart Manufacturing Processes in the Context of Industry 4.0)
  • Article
  • Open Access
6 Citations
2,861 Views
20 Pages

4 April 2023

The hardfacings reinforced by recycled (cermet inserts of machining tools) WC-Co composite particles applied by manual arc welding can be used for protection against abrasive and erosive wear. Two categories of coatings were analyzed: with and withou...

(This article belongs to the Special Issue Enhanced Mechanical Properties of Metals by Surface Treatments)
  • Article
  • Open Access
4 Citations
3,492 Views
14 Pages

The Selection of Cutting Speed to Prevent Deterioration of the Surface in Internal Turning of C45 Steel by Small-Diameter Boring Bars

  • Tomáš Vopát,
  • Marcel Kuruc,
  • Boris Pätoprstý,
  • Marek Vozár and ,
  • František Jurina,
  • Barbora Bočáková,
  • Jozef Peterka,
  • Augustín Görög and
  • Róbert Straka
  • + 4 authors+ 0 author

17 January 2024

The turning of small-diameter deep holes is usually critical when the process of machining is unstable and the use of a special boring bar is often necessary. This paper is focused on the influence of cutting speed with a combination of cutting condi...

(This article belongs to the Special Issue Precision Manufacturing and Machine Tools)