Nanostructured bainite is a novel ultra-high-strength steel-concept under intensive current research, in which the optimization of its mechanical properties can only come from a clear understanding of the parameters that control its ductility. This w...
Bainite transformation is a kinetic process that involves complex solid diffusion and phase structure evolution. This research systematically studies the bainite transformation of austempered 4140 steel in a wide range of isothermal temperatures, in...
The nitrocarburising response of low transformation temperature ultrafine and nanoscale bainitic steel was investigated and compared with martensite and pearlite from the same steel composition. It was found that the retained austenite content of the...
The strength and plasticity balance of F/B dual-phase X80 pipeline steels strongly depends on deformation compatibility between the soft phase of ferrite and the hard phase of bainite; thus, the tensile strength of ferrite and bainite, as non-negligi...
A multiphase microstructure comprising of different volume fractions of prior martensite and ultra-fine bainite (bainitic ferrite and retained austenite) was obtained by quenching to certain temperatures, followed by isothermal bainitic transformatio...
The major strengthening mechanisms in bainitic steels arise from the bainitic ferrite plate thickness rather than the length, which primarily determines the mean free slip distance. Both the strength of the austenite from where the bainite grows and...
It has been reported that a multiphase microstructure with bainite, martensite, and retained austenite obtained by austempering, or quenching and tempering of spring steel containing Si, Mn, and Cr exhibits high strength and ductility. However, littl...
To relate the bainitic microstructures to the mechanical properties of steel, the average dislocation density needs to be determined. Using X-ray diffraction and diffraction line broadening analysis, this research quantifies the average dislocation d...
Bainite transformation behavior was monitored using simultaneous measurements of dilatometry and small angle neutron scattering (SANS). The volume fraction of bainitic ferrite was estimated from the SANS intensity, showing good agreement with the res...
This study aims to investigate the microstructures, strength, and impact toughness of low-temperature bainite obtained by isothermal transformation at temperature below Ms (Martensite Starting temperature) for different times and tempering process in...
This study investigates the role of coalesced bainite in enhancing the hydrogen embrittlement resistance of tempered martensitic steels. By analyzing the microstructural characteristics and mechanical properties under varying cooling rates, it was fo...
Bainitic steels were the focus of this study. These steels have the potential to obtain a good combination of strength, ductility, and edge stretchability, which is a very desirable characteristic in the automotive industry. Cu precipitation potentia...
Ultra-fine carbide-free bainitic (UCFB) steel, also known as nano-bainite (NB) steel, is composed of bainitic ferrite laths with nanoscale thickness and carbon-rich film-like retained austenite located between laths. The bainite transformation kineti...
The mixed structure of lath bainite and martensite was obtained by isothermal transformation tests at 698 K, 673 K and 623 K in ultra-high-strength steel. The interweaving mode of lath bainite and martensite was revealed by colored metallography and...
The thermal stability of nanostructured microstructures consisting of a mixture of bainitic ferrite and carbon-enriched retained austenite has been studied in two steels containing 0.6 C (wt %) by tempering cycles of 1 h at temperatures ranging from...
It has been reported that the duplex bainite microstructure obtained by austempering (AT) shows higher strength, ductility and impact toughness than quench and tempered (QT) martensite structure in SAE9254 spring steel. However, there seems to be no...
An evaluation method for bainite transformation kinetics was established by theoretical derivation, dilatometric curve analysis, and microstructure observation. The isothermal transformation of ultra-fine bainite under different austenitizing tempera...
According to the concept of the bainite-based quenching and partitioning (BQ&P) process, we designed the online heat treatment routes of bainitic rail steel for heavy haul railway. The new heat treatment process reduced the fraction and size of t...
Direct microscopic observation of the isothermal bainite evolution in terms of nucleation events, the location of the nuclei, as well as their growth is very valuable for the refinement of models predicting the kinetics of bainite transformation. To...
The influence of austenitisation temperature and time on the martensitic and isothermal bainite transformation of 51CrV4 spring steel was analysed. Based on the analysis of dilatometric curves, the martensite start temperatures (MS) were determined a...
To develop an advanced high strength steel with reasonable ductility based on low alloying concept as well as micro-composite microstructure essentially consisting of bainite, martensite and retained austenite, a Si-bearing, low alloy medium carbon s...
An advanced bainite rail with high strength–toughness combination was produced in a steel mill and the effects of tempering on the microstructure and properties of the bainite rail steel were investigated by optical microscopy, transmission ele...
Three-dimensional microstructures of bainitic ferrites and prior austenite grains (PAGs) were observed in the initial stage of upper bainite transformation by using a serial sectioning technique and orientation analysis by electron back scattering di...
The growth and propagation behavior of austenite-to-bainite isothermal transformation in laser-cladded, Si-rich, and Fe-based coatings is investigated. The crystallographic features, orientation relationship at different isothermal temperatures, and...
Nanostructured bainite (NB) bearing steel has excellent strength and ductility combinations, which can improve the fatigue life and wear resistance of bearing steel in harsh conditions. However, the phase transformations and the correlation between t...
Nanobainite transformation behavior was comparably studied using in situ observations for two heat treatments: With and without partial quenching before isothermal holding at 300 °C. It was found that the prior martensite formation significantly...
High-strength steels are widely used in various mechanical production and construction industries for their low cost, high strength and high toughness. Among these, bainitic steels have better comprehensive performance relative to martensite and ferr...
In the present study, the isothermal decomposition of austenite to bainite in 1.0 wt% carbon, 0.21% silicon steel during the partitioning step of a quenching and partitioning (Q&P) heat treatment has been investigated in a dilatometer in the temp...
A bainite dual-phase (FB) steel containing polygonal ferrite and granular bainite is thermo-mechanically rolled, followed by an accelerated cooling. Two different cooling rates are applied to obtain two different materials. The aim of the study is to...
The multi-pass deposited metals were prepared by metal-cored wire with low (2.5 wt%) and high (4.0 wt%) Ni to research the effect of Ni on the bainite/martensite transformation. Results showed that deposited metals exhibited a multiphase structure co...
The effect of multi-step austempering treatments on the microstructure and mechanical properties of a novel medium carbon high silicon carbide-free bainitic steel was studied. Five different isothermal treatment processes were selected, including sin...
In this study, the phase transformation behaviour of the carburised layer and the matrix of 23CrNi3Mo steel was comparatively investigated by constructing continuous cooling transformation (CCT) diagram, determining the volume fraction of retained au...
The partitioning and diffusion of solute elements in hot rolling and the effect of the partitioning and diffusion on the ferrite-bainite banding formation after hot rolling in the 20CrMnTi steel were experimentally examined by EPMA (electron probe mi...
This work deals with the kinetic aspects of bainite formation during isothermal holding above and below the martensite start (Ms~275 °C) temperature using a low-alloy, high-silicon DIN 1.5025 steel in a range suitable for achieving ultrafine/nano...
The stability of lath-like microstructures during low-temperature isothermal ageing was analyzed in a Fe5Ni0.33C (in wt %) steel. The microstructures were characterized using Scanning Electron Microscopy (SEM) coupled with Electron Backscatter Diffra...
One of the main limitations in application of nanostructured carbide-free bainite as a construction material is the difficulty of joining. This research presents a structural characterization of welded joints of medium carbon 55Si7 grade steel after...
The influence of V additions on isothermally formed bainite in medium carbon steels containing retained austenite has been investigated using in-situ high energy X-ray diffraction (HEXRD) and ex-situ electron energy loss spectroscopy (EELS) and energ...
In this work, the microstructural evolution during the dynamic transformation of austenite to bainite was directly observed by in-situ high energy synchrotron X-ray diffraction measurements during warm uniaxial compression performed at the P07 beamli...
The isothermal bainitic transformation kinetics, microstructure, and mechanical properties of the quenched low-carbon high-strength steel have been investigated via dilatometric measurements, microstructural characterization, and mechanical tests. Th...
In this work, three deposited metals with different nickel (Ni) contents were produced by active gas metal arc welding (GMAW) in order to explore the influence of Ni on the microstructure evolution and toughness of 800 MPa grade low carbon bainite de...
Samples of medium-carbon low alloyed steel (0.45 wt% C, 2.61 wt% Mn, 1.57 wt% Si) with bainite microstructure were welded using the cold metal transfer method. A series of single welding “dots” was made to produce welding joints using aus...
Laser-based powder bed fusion of metals (PBF-LB/M) is an emerging technology with enormous potential for the fabrication of highly complex products due to the layer-wise fabrication process. Low-alloyed steels have recently gained interest due to the...
Four types of ultra-low carbon bainite (ULCB) steels were obtained using unified production methods to investigate solely the effect of niobium content on the performance of ULCB steels. Tensile testing, low-temperature impact toughness testing, corr...
This investigation explores the influence of the austenitisation heat treatment and thus, of the prior austenite grain size (PAGS), on the kinetics of the bainitic transformation, using as A case study two high-carbon, high-silicon, bainitic steels i...
The aim of this work was to develop a method to evaluate the kinetics of bainite transformation by theoretical deduction and thermal dilatation curve analysis. A Gleeble-3500 thermomechanical simulator and dilatometer (DIL805A) were employed to study...
In order to provide important guidance for controlling and obtaining the optimal microstructures and mechanical properties of a welded joint, the continuous cooling transformation diagram of a new low-carbon Nb-microalloyed bainite E550 steel in a si...
In this study, we investigate the impact of prior ferrite on the bainite transformation kinetics and microstructure of medium-carbon steel interrupted by an intercritical annealing (IAA) process. It was found that the incubation time and completion t...
In this work, we have investigated the effect of martensite/bainite dual phase content on the mechanical properties of EA4T high-speed axle steel. For evaluation and control of the strength, ductility, and toughness of steel, the microstructure of la...
A bainite/martensite multiphase rail is treated by the controlled-cooling process with different finish-cooling temperatures. The simulated temperature–time curves of the position of 5 mm and 15 mm below the rail tread (P5 and P15) express diff...
A crystallographic analysis was conducted of the upper bainite nucleated at the austenite grain boundary in Fe-0.6C-0.8Mn-1.8Si (in mass %) steel by the EBSD analysis. The effect of the character of the prior austenite grain boundary (PAGB) on the fo...
of 12