In this work, the effects of Ce content (0.1%, 0.2%, and 0.3 wt%) on the microstructures and mechanical properties of Al-Cu-Li alloys were investigated. The results show that the grains of Al-Cu-Li alloy are refined by adding Ce element. When Ce cont...
Al-Cu-Li alloys are widely used in aerospace due to their excellent mechanical properties. However, the surface of Al-Cu-Li alloy components is prone to localized corrosion, when it serves in humid environments such as the ocean, due to the action of...
An optimized homogenization process for Al alloy ingots is key to subsequent material manufacturing, as it largely reduces metallurgical defects, such as segregation and secondary phases. However, studies on their exact microstructural evolution at d...
The microstructural evolution and properties of an Al-Cu-Li alloy with Mg and Zn microalloying (Al-3.5Cu-1.5Li-0.5Mg-0.4Zn-0.3Mn-0.12Zr-0.06Ti) ingot subjected to homogenization (second-step annealing at 500 °C for 24 h following first-step annea...
Controlling the formation of the β′ (Al3Zr) phase is pivotal for regulating the recrystallization and thus the mechanical properties of the spray formed 2195 (Al-Cu-Li) alloy. In a conventional “homogenization-extrusion” proces...
After aging heat treatment, Al-Cu-Li alloy, in general, contains a variety of precipitated phases that jointly influence the age-strengthening effect on the alloy. In this work, a multiphase-coupled strengthening model has been established on the bas...
The effects of the addition of 0.29 wt% Ce on the high-temperature mechanical properties of an Al–Cu–Li alloy were investigated. Ce addition contributes to T1 (Al2CuLi) phase coarsening inhibition and Ce-containing intermetallic refinemen...
The aim of this work is to investigate the effect of different second phases on the composite spinning-extrusion forming and mechanical properties of Al–Cu–Li alloy. With that purpose, four kinds of second phases blanks were controlled us...
The effects of pre-stretching on creep behavior, mechanical properties and microstructure during the creep aging process of Al-Cu-Li alloy were investigated. AA2195 was taken as the representative of Al-Cu-Li alloys. It is found that the total creep...
In this work, a Al-Cu-Li alloy plate with outstanding mechanical properties was successfully prepared with electromagnetic twin-roll casting (TRC) technology. The microstructure of Al-Cu-Li alloy manufactured by conventional mold casting, TRC, and el...
In the present work, the effect of Zn on the aging precipitates and mechanical properties of Al-Cu-Li alloys was investigated by Vickers hardness, tensile tests, transmission electron microscopy (TEM) and differential scanning calorimetry (DSC). The...
The effects of the addition of 0.29 wt % Ce on the recrystallization behavior of an Al–Cu–Li–0.13Zr (wt %) alloy during isothermal annealing were investigated. Ce addition greatly improved inhibition of recrystallization in this all...
The mechanical properties of Al-Cu-Li alloys after different pretreatments were investigated through tensile testing at 25 and −196 °C, and the corresponding microstructure characteristics were obtained through optical metallography, scanning electro...
For this article, hot compression tests were carried out on homogenized 2050 Al-Cu-Li alloys under different deformation temperatures and strain rates, and an Arrhenius-type constitutive model with strain compensation was established to accurately de...
The mechanical properties and microstructure evolution of an Al-Cu-Li alloy sheet processed via hot rolling (HR) (at 400 °C and 500 °C) or cryorolling (CR) (at −100 °C and −190 °C) and subsequence aging at 160 °C for 10 h were investigated. Before ag...
High-strength aluminum alloy fabricated using spray deposition technology possesses many advantages, such as fine crystal grains, low component segregation, uniform microstructure, and small internal stress. In this study, spray-deposited 2195 Al-Cu-...
In this paper, the effects of compressive pre-deformation and successive pre-artificial aging on the compressive creep aging behavior and microstructure evolution of the Al-Cu-Li alloy have been studied. Severe hot deformation mainly occurs near the...
In the present study, 2198 Al-Cu-Li alloys were successfully friction stir welded by using various welding speed ranges of 90~180 mm/min with an invariable rotation speed of 950 r/min. The effect of welding speed on microstructure evolution and mecha...
The influence of Cu content (3.10, 3.50, and 3.80 wt.%) on the precipitation behavior and mechanical properties of Al-Cu-Li alloys under two aging conditions (direct aging at 175 °C vs. 3.5% pre-stretching followed by aging at 155 °C) was sys...
In this work, the effects of the Cu/Li ratio on the mechanical properties and corrosion behavior of Sc-containing Al-Cu-Li alloys were systematically investigated by utilizing age-hardening behavior, tensile property, corrosion behavior, and electroc...
This study systematically investigates the effects of Fe and Si impurities on the microstructure and mechanical properties of Al-Cu-Li alloys. Five alloy compositions with controlled Fe (0.03–0.12 wt.%) and Si (0.03–0.12 wt.%) contents we...
The Laser Beam Welding (LBW) of aluminum alloys has attracted significant interest from industrial sectors, including the shipbuilding, automotive and aeronautics industries, as it expects to contribute to significant cost reduction associated with t...
Microstructural optimization of Al-Li alloys plays a key role in the adjustment of mechanical properties as well as corrosion behavior. In this work, Al-5Cu-1Li-0.6Mg-0.5Ag-0.5Mn alloy was homogenized at different temperatures and holding times, foll...
The displacement discontinuity arising between crack surfaces is assigned to smooth densities of crystal defects referred to as disconnections, through the incompatibility of the distortion tensor. In a dual way, the disconnections are defined as lin...
Lightweight structural alloys have broad application prospects in aerospace, energy, and transportation fields, and it is crucial to understand the hot deformation behavior of novel alloys for subsequent applications. The deformation behavior and mic...
Al-Cu-Li alloys are famous for their high strength, ductility and weight-saving properties, and have for many years been the aerospace alloy of choice. Depending on the alloy composition, this multi-phase system may give rise to several phases, inclu...
Thin twin-roll cast strips from a model Al-Cu-Mg-Li-Zr alloy with a small addition of Sc were prepared. A combination of a fast solidification rate and a favorable effect of Sc microalloying refines the grain size and the size of primary phase partic...
The flow behavior of an Al-Cu-Li-Mg-Ag alloy was studied by thermal simulation tests at deformation temperatures between 350 °C and 470 °C and strain rates between 0.01–10 s−1. The microstructures of the deformed materials were characterized by elect...
A homogenization of billets from Al-Cu-Li-Mg-Sc-Zr alloys should be accomplished at high annealing temperatures exceeding 500 °C. This type of aluminum alloy is susceptible to the depletion of surface layers from Li. Therefore, choosing a suitabl...
Aluminum (Al)–copper (Cu)–lithium (Li) alloys are susceptible to environmental degradation, which limits the in-service lifetime of the components. Because of their complex composition, there are seldom studies focusing on corrosion behav...
Equal-channel angular pressing (ECAP) is known to induce significant grain refinement and formation of tangled dislocations within the grains. These are induced to evolve to form low-angle boundaries (i.e., cell boundaries) and eventually high-angle...
In this paper, the microstructure of friction stir welded between the Al–Li–Cu alloy and the Al–Zn–Mg–Cu alloy was studied using optical microscope(OM), electronic backscattered diffraction (EBSD), SEM, and TEM. The hard...
Cryogenic deformation can improve the strength and plasticity of Al–Li alloy, although the underlying mechanism is still not yet well understood. The effects of cryogenic temperature on the tensile properties and microstructure of an Al–Cu–Li alloy w...
This study presents and explains the results of the first steps in developing high strength aluminium alloy (Al–Cu–Li) wires for the ultimate purpose of using them as feedstock for DED (directed energy deposition) techniques, such as wire...
The effect of pre-rolling on the microstructure and fatigue crack (FC) propagation resistance of the Al-Cu-Li alloy was studied using tensile testing, fatigue testing, transmission electron microscopy (TEM), X-ray diffractometer (XRD), and scanning e...
The research aim was to optimize post-weld heat-treatment (PWHT) modes for a laser-welded joint of the Al–Cu–Li alloy and improve their respective strength properties. As a result, the ultimate tensile strength, yield point, and elongatio...
The quench-induced precipitation and subsequent aging response in 2A97 aluminum alloy was investigated based on the systematic microstructure characterization. Specifically, the influence on precipitation from grain structure was examined. The result...
Al-Li alloys are widely used in aerospace applications due to their high strength, high fracture toughness, and strong resistance to stress corrosion. However, the lack of interatomic potentials has hindered systematic investigations of the relations...
The effects of double-step homogenization processes on the precipitation of Al3Zr dispersoids and the dissolution of the primary phases of 2196 aluminum alloy were studied by optical microscopy, scanning electron microscopy (SEM), and transmission el...
Prediction of the accumulated pitting corrosion damage in aluminum-lithium (Al-Li) is of great importance due to the wide application of these alloys in the aerospace industry. The Point Defect Model (PDM) is arguably one of the most well-developed t...
The deformation behavior and microstructural evolution of fine-grained 2050 alloys at elevated temperatures and slow strain rates were investigated. The results showed that significant dynamic anisotropic grain growth occurred at the primary stage of...
In this paper, the high strength and lightweight Al–Cu–Li alloy (AA2099) is considered in as-built and preheated conditions (440 °C, 460 °C, 480 °C, 500 °C, and 520 °C). The purpose of this study is to investigate the...
The influences of aging treatments on microstructures and the corrosion properties of an Al–Cu–Li alloy were investigated through an immersion test in intergranular corrosion (IGC) solutions, a potentiodynamic polarization test, and elect...
The age hardening response of a high-purity Al–4Cu–1Li–0.25Mn alloy (wt. %) during isothermal aging without and with an applied external load was investigated. Plate shaped nanometer size T1 (Al2CuLi) and θ′ (Al2Cu) hard...
The effects of various rolling reductions (64.7%, 72.1%, 81.4% and 88.2%) on the microstructures and mechanical behaviors of Sc-containing Al-3.2Cu-1.5Li-based alloys were experimentally investigated through XRD, SEM (equipped with EBSD), TEM and the...
To analyze the effect of lithium and microstructure on the pitting corrosion behavior of aluminum alloys, three types of aluminum alloys were studied via scanning electron microscopy, transmission electron microscopy, electrochemical polarization, an...
In this paper, the passivation kinetics of AA2098–T851 was investigated by a fundamental theoretical interpretation of experimental results based on the mixed potential model (MPM). The steady state passive layer formed on the AA2098–T851...
Due to their excellent specific strength and lightweight characteristics, Al-Cu-Li alloys are widely used in aerospace applications. The newly developed three-stage creep aging (CA) process ensures both the formability and high performance of the Al...
It is well known that the development of lightweight alloys with improved comprehensive performance and application value are the future development directions for the ultra-high-strength 7xxx series Al-Zn-Mg-Cu alloys used in the aircraft field. As...
Research on the development of new lightweight Al–Li alloys using a selective laser melting process has great potential for industrial applications. This paper reports on the development of novel aluminum–lithium alloys using selective la...
of 2