Special Issue "Non-Conventional Machining of Hard Materials"

A special issue of Materials (ISSN 1996-1944). This special issue belongs to the section "Manufacturing Processes and Systems".

Deadline for manuscript submissions: 20 April 2022.

Special Issue Editors

Dr. Animesh Kumar Basak
E-Mail Website
Guest Editor
Adelaide Microscopy, The University of Adelaide, Adelaide, SA 5005, Australia
Interests: microscopy; machining; 3D printing; tribology; nanostructure materials
Dr. Chander Prakash
E-Mail Website
Guest Editor
Department of Industrial Engineering, School of Mechanical Engineering, Lovely Professional University, Punjab 144411, India
Interests: biomaterials; sustainable manufacturing; surface engineering
Special Issues and Collections in MDPI journals
Dr. Alokesh Pramanik
E-Mail Website
Guest Editor
Department of Mechanical Engineering, Curtin University, GPO Box U1987, Perth, WA 6845, Australia
Interests: manufacturing science; surface engineering
Special Issues and Collections in MDPI journals

Special Issue Information

Dear Colleagues,

This Special Issue, “Non-Conventional Machining of Hard Materials”, will address advances in the non-conventional machining of a wide range of materials, such as metals, ceramics, cermets, and alloys. The use of non-conventional machining technology to machine difficult-to-cut materials is of prime impotence in term of accuracy and overcoming the shortcomings of traditional machining processes such as the deterioration of machined surfaces due to heat exposure. Nevertheless, non-conventional machining has its own challenges, such as recast layer formation during the electrodischarge machining (EDM) process. Selecting the appropriate and economical machining process in any fabrication division is one of the most challenging tasks. Research challenges in the non-conventional machining process remain the same and are growing day-by-day in terms of minimizing product size and waste management.

The purpose of this Special Issue is to collect valuable research articles in which improved techniques are presented with significant contributions to the machining process. This Special Issue aims at the accumulation of recent trends and developments in this field—including experimental, simulation, and reviews. Explaining the advantages and disadvantages of procedures involved in the non-conventional machining process will allow the reader to understand more about the process and will help them to think of and develop more optimized procedures in the near future. Topics of interest include but are not limited to the following:

  • Recent developments in the non-conventional machining process;
  • Modeling/simulation of non-conventional machining processes;
  • Hybrid non-conventional machining processes;
  • Optimization procedures of forming processes;
  • Surface damage models.

I look forward to your contributions.

Dr. Animesh Kumar Basak
Dr. Chander Prakash
Dr. Alokesh Pramanik
Guest Editors

Manuscript Submission Information

Manuscripts should be submitted online at www.mdpi.com by registering and logging in to this website. Once you are registered, click here to go to the submission form. Manuscripts can be submitted until the deadline. All papers will be peer-reviewed. Accepted papers will be published continuously in the journal (as soon as accepted) and will be listed together on the special issue website. Research articles, review articles as well as short communications are invited. For planned papers, a title and short abstract (about 100 words) can be sent to the Editorial Office for announcement on this website.

Submitted manuscripts should not have been published previously, nor be under consideration for publication elsewhere (except conference proceedings papers). All manuscripts are thoroughly refereed through a single-blind peer-review process. A guide for authors and other relevant information for submission of manuscripts is available on the Instructions for Authors page. Materials is an international peer-reviewed open access semimonthly journal published by MDPI.

Please visit the Instructions for Authors page before submitting a manuscript. The Article Processing Charge (APC) for publication in this open access journal is 2000 CHF (Swiss Francs). Submitted papers should be well formatted and use good English. Authors may use MDPI's English editing service prior to publication or during author revisions.

Keywords

  • metals
  • ceramics
  • alloys
  • electrodischarge machining (EDM)
  • ultrasonic machining
  • (abrasive) water jet machining
  • electron beam machining
  • later beam machining
  • ion beam machining

Published Papers

This special issue is now open for submission.
Back to TopTop