Skip to Content

8 Results Found

  • Article
  • Open Access
8 Citations
3,388 Views
13 Pages

27 May 2022

Mark Duffy produced a complete set of grinding data on a pilot-scale tower mill. Here these data are analyzed in terms of grinding kinetics. The results show that the data can be fitted with a simple first-order breakage model, which is not normally...

(This article belongs to the Special Issue Comminution and Comminution Circuits Optimisation)
  • Article
  • Open Access
4 Citations
3,037 Views
18 Pages

Optimization of High-Pressure Grinding Roll (HPGR) Performance in an Industrial-Scale HPGR/Tower Mill Comminution Circuit

  • Bo Wei,
  • Zhitao Yuan,
  • Quan Feng,
  • Qiang Zhang and ,
  • Xinyang Xu,
  • Qingyou Meng,
  • Bern Klein and
  • Lixia Li
  • + 3 authors+ 0 author

11 October 2025

The integration of high-pressure grinding roller (HPGR) with pre-concentration techniques and stirred mills is recognized for its energy efficiency. Studies have suggested that the feed with a P80 around 1 mm is acceptable for stirred mills or coarse...

(This article belongs to the Section Mineral Processing and Extractive Metallurgy)
  • Article
  • Open Access
29 Citations
9,559 Views
20 Pages

Industrial Vertical Stirred Mills Screw Liner Wear Profile Compared to Discrete Element Method Simulations

  • Priscila M. Esteves,
  • Douglas B. Mazzinghy,
  • Roberto Galéry and
  • Luís C. R. Machado

10 April 2021

Vertical stirred mills have been widely applied in the minerals industry, due to its greater efficiency in comparison with conventional tumbling mills. In this context, the agitator liner wear plays an important role in maintenance planning and opera...

(This article belongs to the Special Issue Comminution in the Minerals Industry)
  • Article
  • Open Access
18 Citations
7,571 Views
16 Pages

23 February 2023

Varied types/geometries of stirred mills have been produced by different manufacturers, and the comparison task has been accomplished for some of the technologies, i.e., Tower mill vs IsaMill. However, the main drawbacks of these comparisons were the...

(This article belongs to the Special Issue Comminution and Comminution Circuits Optimisation, Volume II)
  • Article
  • Open Access
3 Citations
3,213 Views
31 Pages

26 May 2023

Senile trees in historic church gardens have natural, aesthetic, historical, and cultural value. Cutting them down too hastily annihilates the achievements of entire generations. We should try to preserve the greenery surrounding historic churches an...

(This article belongs to the Topic Sustainability in Heritage and Urban Planning)
  • Article
  • Open Access
2 Citations
3,086 Views
19 Pages

Revisiting Symptom-Based Fault Tolerant Techniques against Soft Errors

  • Hwisoo So,
  • Moslem Didehban,
  • Yohan Ko,
  • Reiley Jeyapaul and ,
  • Jongho Kim,
  • Youngbin Kim,
  • Kyoungwoo Lee and
  • Aviral Shrivastava
  • + 3 authors+ 0 author

4 December 2021

Aggressive technology scaling and near-threshold computing have made soft error reliability one of the leading design considerations in modern embedded microprocessors. Although traditional hardware/software redundancy-based schemes can provide a hig...

(This article belongs to the Special Issue Advancement of Fault Detection/Diagnosis and Fault-Tolerant Control with Applications)
  • Article
  • Open Access
4 Citations
1,638 Views
16 Pages

Prediction of Circulation Load of Side-Flanged High-Pressure Grinding Rolls Closed-Circuit Crushing

  • Nan Li,
  • Lixia Li,
  • Jiaqi Wang,
  • Zhe Liu and ,
  • Quan Feng,
  • Qiang Zhang,
  • Hui Liu,
  • Bern Klein and
  • Bing Li
  • + 4 authors+ 0 author

4 June 2025

To enhance the performance of the combined high-pressure grinding roller (HPGR) and tower mill (TM) process for −1 mm particle size, this study addresses the key technical challenges of insufficient material quantity (<100 kg) and complex ex...

(This article belongs to the Section Mineral Processing and Extractive Metallurgy)
  • Article
  • Open Access
23 Citations
5,279 Views
19 Pages

Comparative Multi-Modal, Multi-Scale Residual Stress Evaluation in SLM 3D-Printed Al-Si-Mg Alloy (RS-300) Parts

  • Eugene S. Statnik,
  • Fatih Uzun,
  • Svetlana A. Lipovskikh,
  • Yuliya V. Kan and ,
  • Sviatoslav I. Eleonsky,
  • Vladimir S. Pisarev,
  • Pavel A. Somov,
  • Alexey I. Salimon,
  • Yuliya V. Malakhova and
  • Alexander M. Korsunsky
  • + 7 authors+ 2 authors

20 December 2021

SLM additive manufacturing has demonstrated great potential for aerospace applications when structural elements of individual design and/or complex shape need to be promptly supplied. 3D-printable AlSi10Mg (RS-300) alloy is widely used for the fabric...

(This article belongs to the Special Issue Experimental, Modeling and Simulation of Residual Stress in Metallic and Composite Materials)