Skip to Content

8 Results Found

  • Article
  • Open Access
4 Citations
3,706 Views
23 Pages

1 October 2019

A novel computational tool, DIMRACK, is presented for the design of the required length of bottom racks in intake systems. The users may consider clear water cases or the rack’s occlusion due to sediment transport in the river. The computationa...

(This article belongs to the Section Hydraulics and Hydrodynamics)
  • Article
  • Open Access
4 Citations
4,180 Views
21 Pages

Empirical, Dimensional and Inspectional Analysis in the Design of Bottom Intake Racks

  • Juan T. García,
  • Luis G. Castillo,
  • José M. Carrillo and
  • Patricia L. Haro

4 August 2018

Flow over bottom racks is highly turbulent, three-dimensional and spatially varied. The design of bottom intake systems has mainly been studied in the laboratory. The comparison of existing experimental studies shows large deviations in the definitio...

(This article belongs to the Section Hydraulics and Hydrodynamics)
  • Article
  • Open Access
19 Citations
7,769 Views
22 Pages

Influence of Rack Slope and Approaching Conditions in Bottom Intake Systems

  • Luis G. Castillo,
  • Juan T. García and
  • José M. Carrillo

21 January 2017

The study analyzes the flow over bottom racks made of longitudinal T-shaped bars. A clear water flow is considered in a laboratory flume. Free surface profiles, wetted rack lengths, and discharge coefficients are measured, changing parameters such as...

(This article belongs to the Special Issue Modeling of Water Systems)
  • Article
  • Open Access
19 Citations
5,880 Views
35 Pages

Wood- and Cable-Based Variable Tilt Stilt-Mounted Solar Photovoltaic Racking System

  • Uzair Jamil,
  • Nicholas Vandewetering,
  • Seyyed Ali Sadat and
  • Joshua M. Pearce

9 January 2024

The prohibitive costs of small-scale solar photovoltaic (PV) racks decrease PV adoption velocity. To overcome these costs challenges, an open hardware design method is used to develop two novel variable tilt racking designs. These are the first stilt...

(This article belongs to the Section Energy System Design)
  • Article
  • Open Access
7 Citations
4,054 Views
21 Pages

Occlusion in Bottom Intakes with Circular Bars by Flow with Gravel-Sized Sediment. An Experimental Study

  • Juan T. Garcia,
  • Luis G. Castillo,
  • Patricia L. Haro and
  • Jose M. Carrillo

21 November 2018

Obstruction of the racks in bottom intakes due to sediment wedged in the slit of the bars can significantly reduce diverted flow. Notwithstanding the design recommendations that are found in the literature, the problem of rack occlusion continues to...

(This article belongs to the Section Hydraulics and Hydrodynamics)
  • Feature Paper
  • Article
  • Open Access
10 Citations
4,927 Views
23 Pages

Field Investigation of Hydraulics and Fish Guidance Efficiency of a Horizontal Bar Rack-Bypass System

  • Mohammadreza Maddahi,
  • Roland Hagenbüchli,
  • Ricardo Mendez,
  • Claudia Zaugg and ,
  • Robert Michael Boes and
  • Ismail Albayrak
  • + 1 author+ 0 author

1 March 2022

This paper investigates the hydraulics and fish guidance efficiency of a Horizontal Bar Rack-Bypass System (HBR-BS) installed at a hydropower plant with a design discharge of 33 m3/s. The HBR is placed at a horizontal rack angle of 38° to the flo...

(This article belongs to the Special Issue Fish Passage at Hydropower Dams)
  • Article
  • Open Access
2,219 Views
20 Pages

2 October 2024

This paper discusses the possible early crack detectability performances of low contact ratio (LCR) and high contact ratio (HCR) spur gears. CAD models of the LCR and HCR gears are created using the rack cutter type tool. Static bending stress analys...

(This article belongs to the Special Issue Fault Diagnosis and Health Monitoring of Mechanical Systems)
  • Article
  • Open Access
506 Views
20 Pages

Skiving of Spur Face Gears and Verification of Meshing Performance of Modified Gear Pair

  • Chuang Jiang,
  • Zhilong Huang,
  • Jianjun Yang,
  • Bingyang Wei and
  • Zhengyang Han

2 September 2026

Power skiving has become an increasingly adopted process for manufacturing spur face gears. However, achieving satisfactory meshing performance remains challenging, mainly because the tooth surface produced by skiving does not fully coincide with the...

(This article belongs to the Section Process Control, Modeling and Optimization)