Selected Papers from the 2nd International Electronic Conference on Machines and Applications (IECMA 2024)

A special issue of Machines (ISSN 2075-1702).

Deadline for manuscript submissions: 15 February 2025 | Viewed by 88

Special Issue Editors

E-Mail Website
Guest Editor
CISE—Electromechatronic Systems Research Centre, University of Beira Interior, Calçada Fonte do Lameiro, P-6201-001 Covilhã, Portugal
Interests: diagnosis and fault tolerance of electrical machines, power electronics and drives
Special Issues, Collections and Topics in MDPI journals

E-Mail Website
Guest Editor
Department of Mechanical Engineering, The Hong Kong Polytechnic University, Hong Kong, China
Interests: robotics and mechatronics; high performance parallel robotic machine development; sustainable/green manufacturing systems; micro/nano manipulation and MEMS devices (sensors); micro mobile robots and control of multi-robot cooperation; intelligent servo control system for the MEMS based high-performance micro-robot; web-based remote manipulation; rehabilitation robot and rescue robot
Special Issues, Collections and Topics in MDPI journals

E-Mail Website1 Website2
Guest Editor
Department of Electrical Engineering, Universitat de València, 46022 Valencia, Spain
Interests: electric motors; fault diagnosis; transient analysis; signal processing; wavelet analysis; infrared thermography; time-frequency transforms
Special Issues, Collections and Topics in MDPI journals

Special Issue Information

Dear Colleagues,

This Special Issue will comprise extended versions of proceedings papers from the 2nd International Electronic Conference on Machines and Applications (IECMA 2024), which will be held online from 18 to 20 June 2024, on (

In this 2nd edition of the e-conference, contributors are invited to provide papers and presentations from the field of machines and their applications at large. Selected papers that are expected to attract the most interest on the web, or that will provide a particularly innovative contribution, will be gathered for publication. These papers will be subjected to peer review and published in the Special Issue, with the aim of rapid and wide dissemination of the research results, developments, and applications.

We hope that this conference series will further expand in the future and become recognized as a new avenue by which to (electronically) present novel developments related to the field of machines and their applications.

Suitable topics for this Special Issue include, but are not limited to, the following:

  • Additive Manufacturing;
  • Condition Monitoring and Fault Diagnosis;
  • Automation and Control Systems;
  • Mechatronic and Intelligent Machines;
  • Turbomachinery;
  • Electrical Machines and Drives;
  • Vehicle Dynamics and Control;
  • Friction and Tribology.

Prof. Dr. Antonio J. Marques Cardoso
Prof. Dr. Dan Zhang
Prof. Dr. Jose Alfonso Antonino-Daviu
Guest Editors

Manuscript Submission Information

Manuscripts should be submitted online at by registering and logging in to this website. Once you are registered, click here to go to the submission form. Manuscripts can be submitted until the deadline. All submissions that pass pre-check are peer-reviewed. Accepted papers will be published continuously in the journal (as soon as accepted) and will be listed together on the special issue website. Research articles, review articles as well as short communications are invited. For planned papers, a title and short abstract (about 100 words) can be sent to the Editorial Office for announcement on this website.

Submitted manuscripts should not have been published previously, nor be under consideration for publication elsewhere (except conference proceedings papers). All manuscripts are thoroughly refereed through a single-blind peer-review process. A guide for authors and other relevant information for submission of manuscripts is available on the Instructions for Authors page. Machines is an international peer-reviewed open access monthly journal published by MDPI.

Please visit the Instructions for Authors page before submitting a manuscript. The Article Processing Charge (APC) for publication in this open access journal is 2400 CHF (Swiss Francs). Submitted papers should be well formatted and use good English. Authors may use MDPI's English editing service prior to publication or during author revisions.


  • automation and control
  • electrical machines
  • turbomachinery
  • intelligent machines
  • additive manufacturing
  • condition monitoring
  • fault diagnosis

Published Papers

This special issue is now open for submission.
Back to TopTop