polymers-logo

Journal Browser

Journal Browser

Nanostructured Polymers and Nanocomposites

A special issue of Polymers (ISSN 2073-4360).

Deadline for manuscript submissions: closed (20 February 2019) | Viewed by 94026

Special Issue Editors


E-Mail Website
Guest Editor
Instituto de Ciencia y Tecnología de Polímeros, Consejo Superior de Investigaciones Científicas (CSIC), Juan de la Cierva 3, Madrid 28006, Spain
Interests: polymer science; polymer modification; self-assembly; nanostructured materials; polymer gels

E-Mail Website
Guest Editor
1. POLYMAT, University of the Basque Country UPV/EHU Avenida de Tolosa 72, Donostia-San Sebastián, Spain
2. Centre for Plastic Electronics and Department of Materials, Imperial College London, London, UK
Interests: organic functional materials; polymer physics; polymer nanotechnology; porous aluminium oxide

E-Mail Website
Guest Editor
Institute of Polymer Science and Technology, (ICTP – CSIC), 28006 Madrid, Spain
Interests: polymers; gels; biomedical applications
Special Issues, Collections and Topics in MDPI journals

Special Issue Information

Dear Colleagues,

The 10th ECNP International Conference has established itself as one of the major events on Nanostructured Polymers and Nanocomposites for the European polymer science community. It continues the well-established tradition of international conferences, started with the European Network of Excellence NANOFUN-POLY, bringing together key researcher in an open forum where scientific discussions and dissemination of cutting-edge science and technology is ensured. The conference covers all aspects of polymer science, from fundamentals to applications, e.g., the synthesis of novel polymer architectures, polymer physics, processing, nanotechnologies, biomedicine, energy, etc.

Prof. Dr. Carmen Mijangos
Dr. Jaime Martín
Dr. Rebeca Hernandez Velasco
Guest Editors

Manuscript Submission Information

Manuscripts should be submitted online at www.mdpi.com by registering and logging in to this website. Once you are registered, click here to go to the submission form. Manuscripts can be submitted until the deadline. All submissions that pass pre-check are peer-reviewed. Accepted papers will be published continuously in the journal (as soon as accepted) and will be listed together on the special issue website. Research articles, review articles as well as short communications are invited. For planned papers, a title and short abstract (about 100 words) can be sent to the Editorial Office for announcement on this website.

Submitted manuscripts should not have been published previously, nor be under consideration for publication elsewhere (except conference proceedings papers). All manuscripts are thoroughly refereed through a single-blind peer-review process. A guide for authors and other relevant information for submission of manuscripts is available on the Instructions for Authors page. Polymers is an international peer-reviewed open access semimonthly journal published by MDPI.

Please visit the Instructions for Authors page before submitting a manuscript. The Article Processing Charge (APC) for publication in this open access journal is 2700 CHF (Swiss Francs). Submitted papers should be well formatted and use good English. Authors may use MDPI's English editing service prior to publication or during author revisions.

Keywords

  • Nanostructured polymers
  • Nanocomposites
  • Polymer synthesis
  • Biomedicine
  • Nanotechnology
  • Processing
  • Functional polymers
  • Sustainability
  • Smart polymers
  • Energy

Benefits of Publishing in a Special Issue

  • Ease of navigation: Grouping papers by topic helps scholars navigate broad scope journals more efficiently.
  • Greater discoverability: Special Issues support the reach and impact of scientific research. Articles in Special Issues are more discoverable and cited more frequently.
  • Expansion of research network: Special Issues facilitate connections among authors, fostering scientific collaborations.
  • External promotion: Articles in Special Issues are often promoted through the journal's social media, increasing their visibility.
  • e-Book format: Special Issues with more than 10 articles can be published as dedicated e-books, ensuring wide and rapid dissemination.

Further information on MDPI's Special Issue polices can be found here.

Published Papers (18 papers)

Order results
Result details
Select all
Export citation of selected articles as:

Research

Jump to: Other

18 pages, 7682 KiB  
Article
Solvent-Free Synthesis of Amidated Carboxymethyl Cellulose Derivatives: Effect on the Thermal Properties
by Asja Pettignano, Aurélia Charlot and Etienne Fleury
Polymers 2019, 11(7), 1227; https://doi.org/10.3390/polym11071227 - 23 Jul 2019
Cited by 51 | Viewed by 12540
Abstract
The present work explores the possibility of chemically modifying carboxymethyl cellulose (CMC), a widely diffused commercial cellulose ether, by grafting of hydrophobic moieties. Amidation of CMC, at high temperature and in heterogeneous conditions, was selected as synthetic tool for grafting on CMC a [...] Read more.
The present work explores the possibility of chemically modifying carboxymethyl cellulose (CMC), a widely diffused commercial cellulose ether, by grafting of hydrophobic moieties. Amidation of CMC, at high temperature and in heterogeneous conditions, was selected as synthetic tool for grafting on CMC a panel of commercially available amines (bearing long aliphatic chains, alkyl aromatic and heteroaromatic groups, more or less spaced from the cellulose backbone). The reaction was successfully carried out in absence of solvents, catalysts and coupling agents, providing a promising and more sustainable alternative to conventional amidation procedures. Relationships between the chemical structure of the obtained CMC derivatives and their thermal properties were carefully studied, with a particular attention to the thermal behavior. Grafting of aromatic and heteroaromatic alkyl amines, presenting a linear alkyl chain between CMC backbone and a terminal bulky moiety, allowed for efficiently separating the polysaccharide chains, improving their mobility and resulting in a consequent lowering of the glass transition temperature (Tg). The Tg values obtained (90–147 °C) were found to be closely dependent on both the size of the aliphatic spacer, the structure of the aromatic ring and the extent of amidation. Full article
(This article belongs to the Special Issue Nanostructured Polymers and Nanocomposites)
Show Figures

Graphical abstract

23 pages, 9942 KiB  
Article
Effect of Cellulose Nanofibrils and TEMPO-mediated Oxidized Cellulose Nanofibrils on the Physical and Mechanical Properties of Poly(vinylidene fluoride)/Cellulose Nanofibril Composites
by Eftihia Barnes, Jennifer A. Jefcoat, Erik M. Alberts, Mason A. McKechnie, Hannah R. Peel, J. Paige Buchanan, Charles A. Weiss Jr., Kyle L. Klaus, L. Christopher Mimun and Christopher M. Warner
Polymers 2019, 11(7), 1091; https://doi.org/10.3390/polym11071091 - 27 Jun 2019
Cited by 36 | Viewed by 5945
Abstract
Cellulose nanofibrils (CNFs) are high aspect ratio, natural nanomaterials with high mechanical strength-to-weight ratio and promising reinforcing dopants in polymer nanocomposites. In this study, we used CNFs and oxidized CNFs (TOCNFs), prepared by a 2,2,6,6-tetramethylpiperidine-1-oxyl radical (TEMPO)-mediated oxidation process, as reinforcing agents in [...] Read more.
Cellulose nanofibrils (CNFs) are high aspect ratio, natural nanomaterials with high mechanical strength-to-weight ratio and promising reinforcing dopants in polymer nanocomposites. In this study, we used CNFs and oxidized CNFs (TOCNFs), prepared by a 2,2,6,6-tetramethylpiperidine-1-oxyl radical (TEMPO)-mediated oxidation process, as reinforcing agents in poly(vinylidene fluoride) (PVDF). Using high-shear mixing and doctor blade casting, we prepared free-standing composite films loaded with up to 5 wt % cellulose nanofibrils. For our processing conditions, all CNF/PVDF and TOCNF/PVDF films remain in the same crystalline phase as neat PVDF. In the as-prepared composites, the addition of CNFs on average increases crystallinity, whereas TOCNFs reduces it. Further, addition of CNFs and TOCNFs influences properties such as surface wettability, as well as thermal and mechanical behaviors of the composites. When compared to neat PVDF, the thermal stability of the composites is reduced. With regards to bulk mechanical properties, addition of CNFs or TOCNFs, generally reduces the tensile properties of the composites. However, a small increase (~18%) in the tensile modulus was observed for the 1 wt % TOCNF/PVDF composite. Surface mechanical properties, obtained from nanoindentation, show that the composites have enhanced performance. For the 5 wt % CNF/PVDF composite, the reduced modulus and hardness increased by ~52% and ~22%, whereas for the 3 wt % TOCNF/PVDF sample, the increase was ~23% and ~25% respectively. Full article
(This article belongs to the Special Issue Nanostructured Polymers and Nanocomposites)
Show Figures

Graphical abstract

17 pages, 3023 KiB  
Article
Active Role of ZnO Nanorods in Thermomechanical and Barrier Performance of Poly(vinyl alcohol-co-ethylene) Formulations for Flexible Packaging
by Francesca Luzi, Alessandro Di Michele, Luigi Torre and Debora Puglia
Polymers 2019, 11(5), 922; https://doi.org/10.3390/polym11050922 - 26 May 2019
Cited by 8 | Viewed by 3410
Abstract
Poly(vinyl alcohol-co-ethylene) (EVOH) films containing zinc oxide nanorods (ZnO Nrods) at 0.1, 0.5, and 1 wt%, were realized by solvent casting. The effect of ZnO Nrods content on morphological, thermal, optical, mechanical, and oxygen permeability properties were analyzed. In addition, moisture content and [...] Read more.
Poly(vinyl alcohol-co-ethylene) (EVOH) films containing zinc oxide nanorods (ZnO Nrods) at 0.1, 0.5, and 1 wt%, were realized by solvent casting. The effect of ZnO Nrods content on morphological, thermal, optical, mechanical, and oxygen permeability properties were analyzed. In addition, moisture content and accelerated-aging test studies were performed, with the intention to determine the influence of zinc oxide nanofillers on the functional characteristics of realized packaging systems. Tensile properties showed increased values for strength and deformation-at-break in EVOH-based formulations reinforced with 0.1 and 0.5 wt% of zinc oxide nanorods. Results from the colorimetric and transparency investigations underlined that the presence of ZnO Nrods in EVOH copolymer did not induce evident alterations. In addition, after the accelerated-aging test, the colorimetric test confirmed the possibility for these materials to be used in the packaging sector. This behavior was induced by the presence of zinc oxide nanofillers that act as a UV block that made them useful as an efficient absorber of UV radiation. Full article
(This article belongs to the Special Issue Nanostructured Polymers and Nanocomposites)
Show Figures

Graphical abstract

12 pages, 3142 KiB  
Article
Polysaccharide Coating of Gelatin Gels for Controlled BSA Release
by Jimena S. Gonzalez, Carmen Mijangos and Rebeca Hernandez
Polymers 2019, 11(4), 702; https://doi.org/10.3390/polym11040702 - 17 Apr 2019
Cited by 21 | Viewed by 4152
Abstract
Self-assembly of natural polymers constitute a powerful route for the development of functional materials. In particular, layer-by-layer (LBL) assembly constitutes a versatile technique for the nanostructuration of biobased polymers into multilayer films. Gelatin has gained much attention for its abundance, biodegradability, and excellent [...] Read more.
Self-assembly of natural polymers constitute a powerful route for the development of functional materials. In particular, layer-by-layer (LBL) assembly constitutes a versatile technique for the nanostructuration of biobased polymers into multilayer films. Gelatin has gained much attention for its abundance, biodegradability, and excellent gel-forming properties. However, gelatin gels melt at low temperature, thus limiting its practical application. With respect to the above considerations, here, we explored the potential application of gelatin gels as a matrix for protein delivery at physiological temperature. A model protein, bovine serum albumin (BSA), was encapsulated within gelatin gels and then coated with a different number of bilayers of alginate and chitosan (10, 25, 50) in order to modify the diffusion barrier. The coated gel samples were analyzed by means of Attenuated Total Reflectance-Fourier Transform Infrared (ATR-FTIR) and confocal Raman spectroscopy, and it was found that the multilayer coatings onto polymer film were interpenetrated to some extent within the gelatin. The obtained results inferred that the coating of gelatin gels with polysaccharide multilayer film increased the thermal stability of gelatin gels and modulated the BSA release. Finally, the influence of a number of bilayers onto the drug release mechanism was determined. The Ritger-Peppas model was found to be the most accurate to describe the diffusion mechanism. Full article
(This article belongs to the Special Issue Nanostructured Polymers and Nanocomposites)
Show Figures

Graphical abstract

18 pages, 4361 KiB  
Article
Isothermal Crystallization Kinetics and Morphology of Double Crystalline PCL/PBS Blends Mixed with a Polycarbonate/MWCNTs Masterbatch
by Thandi P. Gumede, Adriaan S. Luyt, Agnieszka Tercjak and Alejandro J. Müller
Polymers 2019, 11(4), 682; https://doi.org/10.3390/polym11040682 - 15 Apr 2019
Cited by 11 | Viewed by 3961
Abstract
In this work, the 70/30 and 30/70 w/w polycaprolactone (PCL)/polybutylene succinate (PBS) blends and their corresponding PCL/PBS/(polycarbonate (PC)/multiwalled carbon nanotubes (MWCNTs) masterbatch) nanocomposites were prepared in a twin-screw extruder. The nanocomposites contained 1.0 and 4.0 wt% MWCNTs. The blends showed a sea-island morphology [...] Read more.
In this work, the 70/30 and 30/70 w/w polycaprolactone (PCL)/polybutylene succinate (PBS) blends and their corresponding PCL/PBS/(polycarbonate (PC)/multiwalled carbon nanotubes (MWCNTs) masterbatch) nanocomposites were prepared in a twin-screw extruder. The nanocomposites contained 1.0 and 4.0 wt% MWCNTs. The blends showed a sea-island morphology typical of immiscible blends. For the nanocomposites, three phases were formed: (i) The matrix (either PCL- or PBS-rich phase depending on the composition), (ii) dispersed polymer droplets of small size (either PCL- or PBS-rich phase depending on the composition), and (iii) dispersed aggregates of tens of micron sizes identified as PC/MWCNTs masterbatch. Atomic force microscopy (AFM) results showed that although most MWCNTs were located in the PC dispersed phase, some of them migrated to the polymer matrix. This is due to the partial miscibility and intimate contact at the interfaces between blend components. Non-isothermal differential scanning calorimetry (DSC) scans for the PCL/PBS blends showed an increase in the crystallization temperature (Tc) of the PCL-rich phase indicating a nucleation effect caused by the PBS-rich phase. For the nanocomposites, there was a decrease in Tc values. This was attributed to a competition between two effects: (1) The partial miscibility of the PC-rich and the PCL-rich and PBS-rich phases, and (2) the nucleation effect of the MWCNTs. The decrease in Tc values indicated that miscibility was the dominating effect. Isothermal crystallization results showed that the nanocomposites crystallized slower than the neat blends and the homopolymers. The introduction of the masterbatch generally increased the thermal conductivity of the blend nanocomposites and affected the mechanical properties. Full article
(This article belongs to the Special Issue Nanostructured Polymers and Nanocomposites)
Show Figures

Graphical abstract

13 pages, 4098 KiB  
Article
Polymer Grafted Aluminum Nanoparticles for Percolative Composite Films with Enhanced Compatibility
by Chenggong Yang, Chufarov Marian, Jie Liu, Qi Di, Mingze Xu, Yunhe Zhang, Wei Han and Kun Liu
Polymers 2019, 11(4), 638; https://doi.org/10.3390/polym11040638 - 8 Apr 2019
Cited by 7 | Viewed by 3166
Abstract
Aluminum nanoparticles hold promise for highly energetic materials and sustainable surface plasmonic materials. Most of the commercial Al nanoparticles are prepared via a high-throughput electrical explosion of wires method (up to 200 g h−1). However, the use of Al nanoparticles produced [...] Read more.
Aluminum nanoparticles hold promise for highly energetic materials and sustainable surface plasmonic materials. Most of the commercial Al nanoparticles are prepared via a high-throughput electrical explosion of wires method (up to 200 g h−1). However, the use of Al nanoparticles produced by an electrical explosion of wires is limited by their micrometer-sized aggregations and poor stability. Here, we use polystyrene with –COOH end-group to graft onto isolated Al nanoparticles and dramatically enhance their colloidal stability in various organic solvents. We further demonstrate that the polystyrene grafted Al nanoparticles can be doped into polystyrene films with high compatibility, leading to enhanced dielectric properties, such as higher dielectric constant, lower dielectric loss, and stronger breakdown strength. Moreover, the composite film can improve the moisture resistance of embedded Al nanoparticles. Full article
(This article belongs to the Special Issue Nanostructured Polymers and Nanocomposites)
Show Figures

Graphical abstract

18 pages, 7465 KiB  
Article
Direction Dependent Electrical Conductivity of Polymer/Carbon Filler Composites
by Karina Kunz, Beate Krause, Bernd Kretzschmar, Levente Juhasz, Oliver Kobsch, Wolfgang Jenschke, Mathias Ullrich and Petra Pötschke
Polymers 2019, 11(4), 591; https://doi.org/10.3390/polym11040591 - 1 Apr 2019
Cited by 24 | Viewed by 7419
Abstract
The method of measuring electrical volume resistivity in different directions was applied to characterize the filler orientation in melt mixed polymer composites containing different carbon fillers. For this purpose, various kinds of fillers with different geometries and aspect ratios were selected, namely carbon [...] Read more.
The method of measuring electrical volume resistivity in different directions was applied to characterize the filler orientation in melt mixed polymer composites containing different carbon fillers. For this purpose, various kinds of fillers with different geometries and aspect ratios were selected, namely carbon black (CB), graphite (G) and expanded graphite (EG), branched multiwalled carbon nanotubes (b-MWCNTs), non-branched multiwalled carbon nanotubes (MWCNTs), and single-walled carbon nanotubes (SWCNTs). As it is well known that the shaping process also plays an important role in the achieved electrical properties, this study compares results for compression molded plates with random filler orientations in the plane as well as extruded films, which have, moreover, conductivity differences between extrusion direction and perpendicular to the plane. Additionally, the polymer matrix type (poly (vinylidene fluoride) (PVDF), acrylonitrile butadiene styrene (ABS), polyamide 6 (PA6)) and filler concentration were varied. For the electrical measurements, a device able to measure the electrical conductivity in two directions was developed and constructed. The filler orientation was analyzed using the ratio σin/th calculated as in-plane conductivity σin-planein) divided by through-plane conductivity σthrough-planeth). The ratio σin/th is expected to increase with more pronounced filler orientation in the processing direction. In the extruded films, alignment within the plane was assigned by dividing the in-plane conductivity in the extrusion direction (x) by the in-plane conductivity perpendicular to the extrusion direction (y). The conductivity ratios depend on filler type and concentration and are higher the higher the filler aspect ratio and the closer the filler content is to the percolation concentration. Full article
(This article belongs to the Special Issue Nanostructured Polymers and Nanocomposites)
Show Figures

Graphical abstract

13 pages, 3979 KiB  
Article
Electrospinning of Ethylene Vinyl Acetate/Carbon Nanotube Nanocomposite Fibers
by Mária Omastová, Eliška Číková and Matej Mičušík
Polymers 2019, 11(3), 550; https://doi.org/10.3390/polym11030550 - 22 Mar 2019
Cited by 19 | Viewed by 5005
Abstract
Nanocomposites, based on an ethylene vinyl acetate (EVA) copolymer with a vinyl acetate content of 34 wt % and varying amounts of multiwall carbon nanotubes (MWCNTs), were prepared by an electrospinning method. The dispersibility of the MWCNTs in the solution was improved by [...] Read more.
Nanocomposites, based on an ethylene vinyl acetate (EVA) copolymer with a vinyl acetate content of 34 wt % and varying amounts of multiwall carbon nanotubes (MWCNTs), were prepared by an electrospinning method. The dispersibility of the MWCNTs in the solution was improved by using cholesteryl 1-pyrenecarboxylate (PyChol) as a compatibilizer. The transmission electron microscopy images showed that the MWCNTs were aligned inside of the elastomeric matrix by the electrospinning process. The morphologies of the fibers were evaluated by scanning electron microscopy. When the amount of MWCNTs in the polymer solution reached 3 wt %, fibers with a diameter of 846 ± 447 nm were prepared. The chemical composition of the prepared fibers was investigated by Fourier transform infrared spectroscopy (FTIR) and X-ray photoelectron spectroscopy (XPS). FTIR results confirmed the presence of a carboxyl group, originating from the presence of PyChol. XPS results showed that the EVA fibers produced by electrospinning were oxidized in ethylene units, when comparing the spectra of the original EVA granules, but the presence of MWCNTs enhanced the stability of the EVA. The thermal stabilities of the fibers were tested with thermogravimetric analysis. The results confirmed that the presence of MWCNTs inside the fibers enhanced the thermal stabilities of the prepared nanocomposites. Full article
(This article belongs to the Special Issue Nanostructured Polymers and Nanocomposites)
Show Figures

Figure 1

14 pages, 3253 KiB  
Article
Glass-Transition Dynamics of Mixtures of Linear Poly(vinyl methyl ether) with Single-Chain Polymer Nanoparticles: Evidence of a New Type of Nanocomposite Materials
by Beatriz Robles-Hernández, Marina González-Burgos, José A. Pomposo, Juan Colmenero and Ángel Alegría
Polymers 2019, 11(3), 533; https://doi.org/10.3390/polym11030533 - 21 Mar 2019
Cited by 8 | Viewed by 3248
Abstract
Single-chain polymer nanoparticles (SCNPs) obtained through chain collapse by intramolecular cross-linking are attracting increasing interest as components of all-polymer nanocomposites, among other applications. We present a dielectric relaxation study on the dynamics of mixtures of poly(vinyl methyl ether) (PVME) and polystyrene (PS)-based SCNPs [...] Read more.
Single-chain polymer nanoparticles (SCNPs) obtained through chain collapse by intramolecular cross-linking are attracting increasing interest as components of all-polymer nanocomposites, among other applications. We present a dielectric relaxation study on the dynamics of mixtures of poly(vinyl methyl ether) (PVME) and polystyrene (PS)-based SCNPs with various compositions. Analogous dielectric measurements on a miscible blend of PVME with the linear precursor chains of the SCNPs are taken as reference for this study. Both systems present completely different behaviors: While the blend with the linear precursor presents dynamics very similar to that reported for PVME/PS miscible blends, in the PVME/SCNP mixtures there are an appreciable amount of PVME segments that are barely affected by the presence of SCNPs, which nearly vanishes only for mixtures with high SCNP content. Interestingly, in the frame of a simple two-phase system, our findings point towards the existence of a SCNP-rich phase with a constant PVME fraction, regardless of the overall concentration of the mixture. Moreover, the dynamics of the PVME segments in this SCNP-rich phase display an extreme dynamic heterogeneity, a signature of constraint effects. Full article
(This article belongs to the Special Issue Nanostructured Polymers and Nanocomposites)
Show Figures

Graphical abstract

15 pages, 2308 KiB  
Article
Characterization of Highly Filled PP/Graphite Composites for Adhesive Joining in Fuel Cell Applications
by Piotr Rzeczkowski, Beate Krause and Petra Pötschke
Polymers 2019, 11(3), 462; https://doi.org/10.3390/polym11030462 - 11 Mar 2019
Cited by 52 | Viewed by 5867
Abstract
In order to evaluate the suitability of graphite composite materials for use as bipolar plates in fuel cells, polypropylene (PP) was melt compounded with expanded graphite as conductive filler to form composites with different filler contents of 10–80 wt %. Electrical resistivity, thermal [...] Read more.
In order to evaluate the suitability of graphite composite materials for use as bipolar plates in fuel cells, polypropylene (PP) was melt compounded with expanded graphite as conductive filler to form composites with different filler contents of 10–80 wt %. Electrical resistivity, thermal conductivity, and mechanical properties were measured and evaluated as a function of filler content. The electrical and thermal conductivities increased with filler content. Tensile and flexural strengths decreased with the incorporation of expanded graphite in PP. With higher graphite contents, however, both strength values remained more or less unchanged and were below the values of pure PP. Young’s-modulus and flexural modulus increased almost linearly with increasing filler content. The results of the thermogravimetric analysis confirmed the actual filler content in the composite materials. In order to evaluate the wettability and suitability for adhesive joining of graphite composites, contact angle measurements were conducted and surface tensions of composite surfaces were calculated. The results showed a significant increase in the surface tension of graphite composites with increasing filler content. Furthermore, graphite composites were adhesively joined and the strength of the joints was evaluated in the lap-shear test. Increasing filler content in the substrate material resulted in higher tensile lap-shear strength. Additionally, the influence of surface treatment (plasma and chemical) on surface tension and tensile lap-shear strength was investigated. The surface treatment led to a significant improvement of both properties. Full article
(This article belongs to the Special Issue Nanostructured Polymers and Nanocomposites)
Show Figures

Graphical abstract

13 pages, 2239 KiB  
Article
Effect of Chemical Structure and Salt Concentration on the Crystallization and Ionic Conductivity of Aliphatic Polyethers
by Jorge L. Olmedo-Martínez, Leire Meabe, Andere Basterretxea, David Mecerreyes and Alejandro J. Müller
Polymers 2019, 11(3), 452; https://doi.org/10.3390/polym11030452 - 9 Mar 2019
Cited by 29 | Viewed by 5299
Abstract
Poly(ethylene oxide) (PEO) is the most widely used polymer in the field of solid polymer electrolytes for batteries. It is well known that the crystallinity of polymer electrolytes strongly affects the ionic conductivity and its electrochemical performance. Nowadays, alternatives to PEO are actively [...] Read more.
Poly(ethylene oxide) (PEO) is the most widely used polymer in the field of solid polymer electrolytes for batteries. It is well known that the crystallinity of polymer electrolytes strongly affects the ionic conductivity and its electrochemical performance. Nowadays, alternatives to PEO are actively researched in the battery community, showing higher ionic conductivity, electrochemical window, or working temperature range. In this work, we investigated polymer electrolytes based on aliphatic polyethers with a number of methylene units ranging from 2 to 12. Thus, the effect of the lithium bis(trifluoromethanesulfone) imide (LiTFSI) concentration on the crystallization behavior of the new aliphatic polyethers and their ionic conductivity was investigated. In all the cases, the degree of crystallinity and the overall crystallization rate of the polymers decreased drastically with 30 wt % LiTFSI addition. The salt acted as a low molecular diluent to the polyethers according to the expectation of the Flory–Huggins theory for polymer–diluent mixtures. By fitting our results to this theory, the value of the interaction energy density (B) between the polyether and the LiTFSI was calculated, and we show that the value of B must be small to obtain high ionic conductivity electrolytes. Full article
(This article belongs to the Special Issue Nanostructured Polymers and Nanocomposites)
Show Figures

Graphical abstract

15 pages, 4187 KiB  
Article
Comparison of Properties of PVA Nanocomposites Containing Reduced Graphene Oxide and Functionalized Graphene
by Gi Tae Park and Jin-Hae Chang
Polymers 2019, 11(3), 450; https://doi.org/10.3390/polym11030450 - 8 Mar 2019
Cited by 23 | Viewed by 4194
Abstract
The thermal properties, morphologies, oxygen barrier properties, and electrical conductivities of poly(vinyl alcohol) (PVA) hybrid films containing different nanofillers were compared. For the fabrication of the PVA hybrid films, we used reduced graphene oxide (RGO) synthesized from graphite or functionalized hexadecylamine-graphene sheets (HDA-GS) [...] Read more.
The thermal properties, morphologies, oxygen barrier properties, and electrical conductivities of poly(vinyl alcohol) (PVA) hybrid films containing different nanofillers were compared. For the fabrication of the PVA hybrid films, we used reduced graphene oxide (RGO) synthesized from graphite or functionalized hexadecylamine-graphene sheets (HDA-GS) obtained from HDA and GS as a reinforcing filler. The properties of the PVA hybrid films fabricated by intercalating PVA and the fillers for different filler contents ranging from 3 to 10% w/w were then compared. The dispersions of the graphene fillers in the matrix polymers were examined using wide-angle X-ray diffraction and field emission scanning electron microscopy, and the changes in their thermal properties were observed using differential scanning calorimetry and thermogravimetric analysis. Moreover, we measured the oxygen permeability and electrical conductivity of the films to investigate their industrial applications. In addition, all the physical properties of the PVA composites obtained using the two nanofillers were compared. Full article
(This article belongs to the Special Issue Nanostructured Polymers and Nanocomposites)
Show Figures

Figure 1

12 pages, 3010 KiB  
Article
Development of Surface-Coated Polylactic Acid/Polyhydroxyalkanoate (PLA/PHA) Nanocomposites
by J. J. Relinque, A. S. de León, J. Hernández-Saz, M. G. García-Romero, Francisco J. Navas-Martos, G. Morales-Cid and S. I. Molina
Polymers 2019, 11(3), 400; https://doi.org/10.3390/polym11030400 - 1 Mar 2019
Cited by 27 | Viewed by 5860
Abstract
This work reports on the design and development of nanocomposites based on a polymeric matrix containing biodegradable Polylactic Acid (PLA) and Polyhydroxyalkanoate (PHA) coated with either Graphite NanoPlatelets (GNP) or silver nanoparticles (AgNP). Nanocomposites were obtained by mechanical mixing under mild conditions and [...] Read more.
This work reports on the design and development of nanocomposites based on a polymeric matrix containing biodegradable Polylactic Acid (PLA) and Polyhydroxyalkanoate (PHA) coated with either Graphite NanoPlatelets (GNP) or silver nanoparticles (AgNP). Nanocomposites were obtained by mechanical mixing under mild conditions and low load contents (<0.10 wt %). This favours physical adhesion of the additives onto the polymer surface, while the polymeric bulk matrix remains unaffected. Nanocomposite characterisation was performed via optical and focused ion beam microscopy, proving these nanocomposites are selectively modified only on the surface, leaving bulk polymer unaffected. Processability of these materials was proven by the fabrication of samples via injection moulding and mechanical characterisation. Nanocomposites showed enhanced Young modulus and yield strength, as well as better thermal properties when compared with the unmodified polymer. In the case of AgNP coated nanocomposites, the surface was found to be optically active, as observed in the increase of the resolution of Raman spectra, acquired at least 10 times, proving these nanocomposites are promising candidates as surface enhanced Raman spectroscopy (SERS) substrates. Full article
(This article belongs to the Special Issue Nanostructured Polymers and Nanocomposites)
Show Figures

Graphical abstract

19 pages, 4406 KiB  
Article
Nanoforest: Polyaniline Nanotubes Modified with Carbon Nano-Onions as a Nanocomposite Material for Easy-to-Miniaturize High-Performance Solid-State Supercapacitors
by Piotr Olejnik, Marianna Gniadek, Luis Echegoyen and Marta E. Plonska-Brzezinska
Polymers 2018, 10(12), 1408; https://doi.org/10.3390/polym10121408 - 19 Dec 2018
Cited by 25 | Viewed by 4736
Abstract
This article describes a facile low-cost synthesis of polyaniline nanotube (PANINT)–carbon nano-onion (CNO) composites for solid-state supercapacitors. Scanning electron microscopic (SEM) analyses indicate a uniform and ordered composition for the conducting polymer nanotubes immobilized on a thin gold film. The obtained [...] Read more.
This article describes a facile low-cost synthesis of polyaniline nanotube (PANINT)–carbon nano-onion (CNO) composites for solid-state supercapacitors. Scanning electron microscopic (SEM) analyses indicate a uniform and ordered composition for the conducting polymer nanotubes immobilized on a thin gold film. The obtained nanocomposites exhibit a brush-like architecture with a specific capacitance of 946 F g−1 at a scan rate of 1 mV s−1. In addition, the nanocomposites offer high conductivity and a porous and well-developed surface area. The PANINT–CNO nanocomposites were tested as electrodes with high potential and long-term stability for use in easy-to-miniaturize high-performance supercapacitor devices. Full article
(This article belongs to the Special Issue Nanostructured Polymers and Nanocomposites)
Show Figures

Graphical abstract

13 pages, 5305 KiB  
Article
Preparation of the Yellow-Colored Aluminum Pigments with Double-Layer Structure Using a Crosslinked Copolymeric Dye
by Zhicheng Wang, Shuping Nie, Ru Xia, Yang Lv, Ming Cao, Ming Chen, Qiannian Dong, Lifen Su, Peng Chen, Bin Yang, Jibin Miao, Zhengzhi Zheng and Jiasheng Qian
Polymers 2018, 10(10), 1097; https://doi.org/10.3390/polym10101097 - 4 Oct 2018
Cited by 5 | Viewed by 3275
Abstract
Colorization for fabricating aluminum pigments has broad application prospects in recent years. In this study, yellow-colored aluminum pigments with the double-layer structure Al@SiO2@PFMV were prepared using a sol-gel method. A crosslinked copolymeric dye (PFMV) was firstly synthesized by radical polymerization using [...] Read more.
Colorization for fabricating aluminum pigments has broad application prospects in recent years. In this study, yellow-colored aluminum pigments with the double-layer structure Al@SiO2@PFMV were prepared using a sol-gel method. A crosslinked copolymeric dye (PFMV) was firstly synthesized by radical polymerization using vinyl triethoxysilane (VTES) and a small molecular dye (FGMAC) as monomers. Then, colored aluminum pigments were prepared by hydrolysis and condensation of the copolymers on the surface of aluminum pigments. SEM, AFM, FTIR, and XPS were used to characterize the surface morphology and chemical structure of the colored aluminum pigments. It was found that the colored aluminum pigments have a heterogeneous and smooth surface layer. The anticorrosion results showed that the colored aluminum pigments had better chemical stability with significantly improving corrosion resistance compared to raw aluminum pigments and Al@SiO2 with the single-layer coating. Chromatism analysis indicated that the lightness of Al@SiO2@PFMV pigments decreased slightly and the color changed from silver-gray to yellow. Full article
(This article belongs to the Special Issue Nanostructured Polymers and Nanocomposites)
Show Figures

Figure 1

7 pages, 1407 KiB  
Communication
Self-Assembly DBS Nanofibrils on Solution-Blown Nanofibers as Hierarchical Ion-Conducting Pathway for Direct Methanol Fuel Cells
by Hang Wang, Xiangxiang Li, Xiaojie Li, Xi Feng, Weimin Kang, Xianlin Xu, Xupin Zhuang and Bowen Cheng
Polymers 2018, 10(9), 1037; https://doi.org/10.3390/polym10091037 - 19 Sep 2018
Cited by 7 | Viewed by 3149
Abstract
In this work, we reported a novel proton exchange membrane (PEM) with an ion-conducting pathway. The hierarchical nanofiber structure was prepared via in situ self-assembling 1,3:2,4-dibenzylidene-d-sorbitol (DBS) supramolecular fibrils on solution-blown, sulfonated poly (ether sulfone) (SPES) nanofiber, after which the composite PEM was [...] Read more.
In this work, we reported a novel proton exchange membrane (PEM) with an ion-conducting pathway. The hierarchical nanofiber structure was prepared via in situ self-assembling 1,3:2,4-dibenzylidene-d-sorbitol (DBS) supramolecular fibrils on solution-blown, sulfonated poly (ether sulfone) (SPES) nanofiber, after which the composite PEM was prepared by incorporating hierarchical nanofiber into the chitosan polymer matrix. Then, the effects of incorporating the hierarchical nanofiber structure on the thermal stability, water uptake, dimensional stability, proton conductivity, and methanol permeability of the composite membranes were investigated. The results show that incorporation of hierarchical nanofiber improves the water uptake, proton conductivity, and methanol permeability of the membranes. Furthermore, the composite membrane with 50% hierarchical nanofibers exhibited the highest proton conductivity of 0.115 S cm−1 (80 °C), which was 69.12% higher than the values of pure chitosan membrane. The self-assembly allows us to generate hierarchical nanofiber among the interfiber voids, and this structure can provide potential benefits for the preparation of high-performance PEMs. Full article
(This article belongs to the Special Issue Nanostructured Polymers and Nanocomposites)
Show Figures

Graphical abstract

11 pages, 3939 KiB  
Article
New Insight into Polydopamine@ZIF-8 Nanohybrids: A Zinc-Releasing Container for Potential Anticancer Activity
by Jingyu Ran, Cong Wang, Jinjuan Zhang, Wei Wang, Lihua Xiao, Shaoyi Jia, Ze Wang, Weidang Wu, Jun Xiao and Xinyu Wu
Polymers 2018, 10(5), 476; https://doi.org/10.3390/polym10050476 - 27 Apr 2018
Cited by 20 | Viewed by 6578
Abstract
Despite the initial evidence on the role of zinc and zinc transporters in cancer prevention, little attention has been paid to the zinc-derived compounds. In the present work, we reported a strategy to prepare a kind of zinc-releasing container with enhanced biocompatibility and [...] Read more.
Despite the initial evidence on the role of zinc and zinc transporters in cancer prevention, little attention has been paid to the zinc-derived compounds. In the present work, we reported a strategy to prepare a kind of zinc-releasing container with enhanced biocompatibility and release dynamics using ZIF-8 nanocrystals as the sacrificial templates. Transmission electron microscopy (TEM) analysis demonstrated that the ZIF-8 nanocrystals were gradually etched out in the aqueous media within 48 h, resulting in hollow nanocapsules. Notably, we found the self-polymerization of dopamine can form nanoshells around the ZIF-8 nanocrystals, which served as a type of functional membranes during the release of zinc. More interestingly, PDA@ZIF-8–based nanohybrids expressed stronger inhibition to the cancer cell growth, which implied that the nanohybrids could be a drug carrier for chemotherapy. This study broadens the biomedical application of ZIF-8 and also provides a versatile strategy toward the development of multifunctional delivery system. Full article
(This article belongs to the Special Issue Nanostructured Polymers and Nanocomposites)
Show Figures

Graphical abstract

Other

Jump to: Research

9 pages, 1874 KiB  
Letter
A Patterned Butyl Methacrylate-co-2-Hydroxyethyl Acrylate Copolymer with Softening Surface and Swelling Capacity
by Laia León-Boigues, Catalina von Bilderling, Lía I. Pietrasanta, Omar Azzaroni, Juan M. Giussi and Carmen Mijangos
Polymers 2019, 11(2), 290; https://doi.org/10.3390/polym11020290 - 9 Feb 2019
Cited by 5 | Viewed by 3074
Abstract
The tunable swelling and mechanical properties of nanostructures polymers are crucial parameters for the creation of adaptive devices to be used in diverse fields, such as drug delivery, nanomedicine, and tissue engineering. We present the use of anodic aluminum oxide templates as a [...] Read more.
The tunable swelling and mechanical properties of nanostructures polymers are crucial parameters for the creation of adaptive devices to be used in diverse fields, such as drug delivery, nanomedicine, and tissue engineering. We present the use of anodic aluminum oxide templates as a nanoreactor to copolymerize butyl methacrylate and 2-hydroxyethyl acrylate under radical conditions. The copolymer obtained under confinement showed significant differences with respect to the same copolymer obtained in bulk conditions. Molecular weights, molecular weight dispersities, Young’s modulus, and wetting behaviors were significantly modified. The combination of selected monomers allowed us to obtain nanopillar structures with an interesting softening surface and extraordinary swelling capacity that could be of special interest to surface science and specifically, cell culture. Full article
(This article belongs to the Special Issue Nanostructured Polymers and Nanocomposites)
Show Figures

Figure 1

Back to TopTop