Submit to Energies Review for Energies Propose a Special Issue

Journal Browser

► Journal Browser

Rock Burst Disasters in Coal Mines

Print Special Issue Flyer
Special Issue Editors
Special Issue Information
Keywords
Published Papers

A special issue of Energies (ISSN 1996-1073). This special issue belongs to the section "H: Geo-Energy".

Deadline for manuscript submissions: closed (31 May 2022) | Viewed by 25758

Share This Special Issue

Special Issue Editors

Dr. Yulong Chen

E-Mail Website
Guest Editor

School of Energy and Mining Engineering, China University of Mining and Technology (Beijing), Beijing 100083, China
Interests: rock permeability; slope stability
Special Issues, Collections and Topics in MDPI journals

Prof. Dr. Junwen Zhang

E-Mail Website
Guest Editor

School of Energy and Mining Engineering, China University of Mining and Technology (Beijing), Beijing 100083, China
Interests: deep coal pressure relief mining; rock burst disaster prevention; rock mechanics
Special Issues, Collections and Topics in MDPI journals

Dr. Jianhang Chen

E-Mail Website
Guest Editor

School of Energy and Mining Engineering, China University of Mining and Technology (Beijing), Beijing 100083, China
Interests: ground control; mining engineering; rock reinforcement
Special Issues, Collections and Topics in MDPI journals

Dr. Xuejie Deng

E-Mail Website
Guest Editor

School of Energy and Mining Engineering, China University of Mining and Technology (Beijing), Beijing 100083, China
Interests: backfill mining and ground control; new backfill materials; rheology; mine waste disposal; environmental protection
Special Issues, Collections and Topics in MDPI journals

Special Issue Information

Dear Colleagues,

Rock bursts are often encountered in coal mines worldwide. In China, rock bursts have been a major safety concern in underground coal mines for more than 50 years. Due to the large uncertainty and variability in rock mass properties (e.g., rock mass strength) and boundary conditions (e.g., in situ stress), the unpredictable and recurrent nature of the phenomenon poses a major safety problem in many hard rock mines and coal mines. The highly frequent occurrence of rock burst disasters in coal mines still seriously restricts the safety and efficiency of the deep underground mining of coal resources. Thus, an in-depth understanding of the failure mechanism of rock bursts is of the utmost importance for the prediction, mitigation and control of geological disasters in deep underground mining and engineering projects.

This Special Issue aims to highlight the state-of-the-art findings in rock bursts, and to address critical issues for the global mining industry. Original theoretical research articles, review articles and case studies are welcome. Potential topics include, but are not limited to, the following:

Long-term stability analysis of deep surrounding rocks;
Fracture mechanism of surrounding rocks in deep excavation;
Occurrence mechanism of rock bursts in coal mines;
Monitoring and early warning of rock bursts;
Pressure relieving and impact reduction mechanism for rock bursts;
Comprehensive prevention system of rock bursts.

Dr. Yulong Chen
Prof. Dr. Junwen Zhang
Dr. Jianhang Chen
Prof. Dr. Xuejie Deng
Guest Editors

Manuscript Submission Information

Manuscripts should be submitted online at www.mdpi.com by registering and logging in to this website. Once you are registered, click here to go to the submission form. Manuscripts can be submitted until the deadline. All submissions that pass pre-check are peer-reviewed. Accepted papers will be published continuously in the journal (as soon as accepted) and will be listed together on the special issue website. Research articles, review articles as well as short communications are invited. For planned papers, a title and short abstract (about 100 words) can be sent to the Editorial Office for announcement on this website.

Submitted manuscripts should not have been published previously, nor be under consideration for publication elsewhere (except conference proceedings papers). All manuscripts are thoroughly refereed through a single-blind peer-review process. A guide for authors and other relevant information for submission of manuscripts is available on the Instructions for Authors page. Energies is an international peer-reviewed open access semimonthly journal published by MDPI.

Please visit the Instructions for Authors page before submitting a manuscript. The Article Processing Charge (APC) for publication in this open access journal is 2600 CHF (Swiss Francs). Submitted papers should be well formatted and use good English. Authors may use MDPI's English editing service prior to publication or during author revisions.

Keywords

rock burst
coal mine
stability
monitoring and prediction
prevention system

Published Papers (14 papers)

Download All Papers

Editorial

Jump to: Research, Review, Other

6 pages, 188 KiB

Open AccessEditorial

Special Issue: Rock Burst Disasters in Coal Mines

by Yulong Chen, Junwen Zhang, Jianhang Chen and Xuejie Deng

Energies 2022, 15(13), 4846; https://doi.org/10.3390/en15134846 - 01 Jul 2022

Cited by 2 | Viewed by 974

Abstract

Rock bursts are often encountered in coal mines worldwide [...] Full article

(This article belongs to the Special Issue Rock Burst Disasters in Coal Mines)

Research

Jump to: Editorial, Review, Other

19 pages, 6069 KiB

Open AccessArticle

Experimental Investigation of Failure Mechanisms of Granites with Prefabricated Cracks Induced by Cyclic-Impact Disturbances

by Jie Zhang, Xun Xi, Wenhui Tan, Xu Wu, Xinghui Wu, Qifeng Guo and Meifeng Cai

Energies 2022, 15(10), 3680; https://doi.org/10.3390/en15103680 - 17 May 2022

Cited by 2 | Viewed by 1502

Abstract

Engineering rock mass is normally subject to cyclic–dynamic disturbances from excavation, blasting, drilling, and earthquakes. Natural fractures in rock masses can be reactivated and propagated under dynamic and static loadings, which affects the stability of rock mass engineering. However, fractured rock mass failure induced by cyclic-impact disturbances is far from clear, especially considering varying angles between the rock mass and the direction of impact loadings. This work investigated rock deformation and failure characteristics through cyclic impact tests on granite samples with cracks of different angles. A Hopkinson bar was employed for uniaxial cyclic impact tests on granite samples with the crack inclination angles of 0–90°. The magnetic resonance imaging technique was used to determine rocks’ porosity after cyclic impacts. The stress–strain curves, porosity, strength, deformation modulus, failure modes, and energy density of samples were obtained and discussed. Results showed that the crack inclination angles significantly affected the damage evolution and crack morphology of rocks. Under the constant cyclic impact, the dynamic deformation modulus and dynamic strength of rock samples first increased and then decreased with the increase in crack inclination angle. The failures of granite samples for inclination angles of 0 and 90° were dominated by tensile cracking, while those for the inclination angles of 30–60° were dominated by shear cracking. The energy density per unit time gradually decreased with the increase in impact cycles. The results can provide references for the stability analysis and cyclic-impact-induced failure prediction of fractured rock masses. Full article

(This article belongs to the Special Issue Rock Burst Disasters in Coal Mines)

► Show Figures

Figure 1

20 pages, 8159 KiB

Open AccessArticle

Study on Overburden Movement and Fissure Evolution Law of Protective Layer Mining in Shallow Coal Seam

by Li Li, Guiyi Wu and Qinzhi Liu

Energies 2022, 15(5), 1831; https://doi.org/10.3390/en15051831 - 02 Mar 2022

Cited by 12 | Viewed by 1734

Abstract

This study aims to effectively solve the problem of the destruction of the coal roof and floor overlying rock after mining the protective layer, and determines whether the gas in the protected layer can be effectively released. We do this based on the engineering background of the Weng’an Coal Mine; research and analysis of the movement of the roof and floor overlying rocks; the evolution of cracks and the pressure relief characteristics of the protected layer after mining the protective layer; and through theoretical analysis and similar simulation experiments. Through numerical simulation, it was found that the protected layer was depressurized due to the mining of the protective layer, and the decompression rate of the protected layer was 0.2–0.8. In addition, the overall expansion rate of the protected layer was greater than the requirements of the “Detailed Rules for Prevention and Control of Coal and Gas Outbursts” for coal mines, and the investigation of the residual gas pressure and content of the protected layer revealed that the protected coal seam had been mined in the upper protective layer coal face. The gas pressure dropped to 50.7% of the original coal seam gas pressure, the rate of decrease was 49.3%, the residual gas content dropped by 68.67%, and the gas concentration in the return airway was 0.31% on average, meeting the national regulations that require its value to be less than or equal to 1%. The study comprehensively demonstrates that mining of the protective layer is beneficial to the release of gas from the protected layer, and provides a practical reference for coal and gas outbursts in mines. Full article

(This article belongs to the Special Issue Rock Burst Disasters in Coal Mines)

► Show Figures

Figure 1

19 pages, 13107 KiB

Open AccessArticle

Numerical Simulation of the Impact of Unmined Longwall Panel on the Working Stability of a Longwall Using UDEC 2D—A Case Study

by Sylwester Rajwa, Tomasz Janoszek, Janina Świątek, Andrzej Walentek and Dominik Bałaga

Energies 2022, 15(5), 1803; https://doi.org/10.3390/en15051803 - 28 Feb 2022

Cited by 4 | Viewed by 1605

Abstract

The main goal of the paper is numerical simulation for investigation of damage causes in the working of a longwall located under the unmined longwall panel. The paper presents the results of model-based research on the stability of the roof of a longwall working in a zone subject to cave-in mining, taking into account the influence of mining conditions in the form of an unmined coal seam located 115 m above the exploited seam. It presents the geometry of the rock mass under study, the discretization area of the solution, and gives an overview of the assumptions used to build the numerical model. The authors discuss the results of numerical simulations of the influence of mining phenomena on the formation of roof falls in the longwall. Based on the results of numerical simulations, the process of identifying the size of roof falls in a longwall working (loss of stability) was carried out through their appropriate classification. The case presented and analyzed in this paper occurred in one of Poland’s coal mines. Full article

(This article belongs to the Special Issue Rock Burst Disasters in Coal Mines)

► Show Figures

Figure 1

17 pages, 47305 KiB

Open AccessArticle

Distribution Law of In Situ Stress and Its Engineering Application in Rock Burst Control in Juye Mining Area

by Guangchao Zhang, You Li, Xiangjun Meng, Guangzhe Tao, Lei Wang, Hanqing Guo, Chuanqi Zhu, Hao Zuo and Zhi Qu

Energies 2022, 15(4), 1267; https://doi.org/10.3390/en15041267 - 09 Feb 2022

Cited by 5 | Viewed by 1490

Abstract

This paper presents an integrated approach for mathematical statistics, theoretical analysis, and a field test to investigate the distribution law of in-situ stress and its engineering practice of rock burst control. The test site is located in the Juye mining area, Shandong Province, China. The main conclusions included: (1) There are two types of in-situ stress states in the Juye mining area, σ_H > σ_V > σ_h (42.42%) and σ_H > σ_h > σ_V (57.57%), which are mainly caused by the tectonic stress of the Heze and Fushan faults (The σ_H, σ_V, and σ_h is the maximum principal stress, vertical principal stress or intermediate principal stress and minimum principal stress respectively). (2) The lateral pressure coefficients K_H, K_h, and K_av show a non-linear distribution with increased depth, approaching 1.32, 0.96, and 1.41, respectively. The variation range of the horizontal difference stress μ_d is 0.09–0.58. (3) The average value of the stress gradient is 3.05 MPa/100 m, and the main directions of the maximum horizontal principal stress are northeast–southwest, and northwest–southeast. (4) A new combined supporting strategy, incorporating optimization of roadway layout, anti-impact support system design, and local reasonable pressure relief, was proposed for the rock burst control, and its validity was verified via field monitoring. All these design principles and support strategies for the rock burst control presented in this study can potentially be applied to other similar projects. Full article

(This article belongs to the Special Issue Rock Burst Disasters in Coal Mines)

► Show Figures

Figure 1

18 pages, 5146 KiB

Open AccessArticle

Stability and Cementation of the Surrounding Rock in Roof-Cutting and Pressure-Relief Entry under Mining Influence

by Xizhan Yue, Min Tu, Yingfu Li, Guanfeng Chang and Chen Li

Energies 2022, 15(3), 951; https://doi.org/10.3390/en15030951 - 27 Jan 2022

Cited by 13 | Viewed by 1924

Abstract

The application of roof-cutting and pressure-relief gob-side entry retention plays a critical role in controlling the stability of the surrounding rock at the entry, easing continuity tension and improving resource recovery ratio. The excavation of the 360,803 airway in Xinji No. 1 Mine is affected by intense mining of the 360,805 working face. Hence, to address the stability problem of surrounding rock in the 360,803 airway, rock mass blast weakening theory was used in this study to analyze the blasting stress of columnar charged rock mass and obtain the radiuses of crushed, fractured, and vibration zones under uncoupled charging conditions. The reasonable array pitch, length, and dip angle of boreholes were determined according to the pressure-relief range of the blasting fracture. The migration laws of roof strata were explored based on a mechanical model of overlying roof strata structure on the working face. Subsequently, the horizon, breaking span, and caving sequence of hard roof strata were obtained to determine the roof-cutting height of this entry. On the basis of the theory of key stratum, the number of sequences at the roof caving limit stratum and hanging roof length in the goaf were calculated, the analytical solution to critical coal pillar width was acquired, the evaluation indexes for the stability of entry-protecting coal pillars were determined, and the engineering requirements for the 25 m entry-protecting coal pillars in the 360,803 airway were met. Moreover, various indexes such as roof separation fracture, displacement of surrounding rock, and loose circle of surrounding rock in the gob-side entry were analyzed. The stability and cementation status of surrounding rock in the 360,803 airway were evaluated, and tunneling safety was ensured. Full article

(This article belongs to the Special Issue Rock Burst Disasters in Coal Mines)

► Show Figures

Figure 1

24 pages, 6275 KiB

Open AccessArticle

Full-Stress Anchoring Technology and Application of Bolts in the Coal Roadway

by Xiaowei Guo, Xigui Zheng, Peng Li, Rui Lian, Cancan Liu, Niaz Muhammad Shahani, Cong Wang, Boyang Li, Wenjie Xu and Guowei Lai

Energies 2021, 14(22), 7475; https://doi.org/10.3390/en14227475 - 09 Nov 2021

Cited by 9 | Viewed by 1580

Abstract

The traditional anchoring method of bolts has insufficient control over the surrounding rock of the coal roadway. Based on this background, full-stress anchoring technology of bolts was proposed. Firstly, a mechanical relationship model of a bolt-drawing, anchoring interface was established to obtain the equations of the axial force and obtain shear stress distribution as well as the decreasing-load transfer law of the anchoring section of bolts. Through studying the prestress-loading experimental device of bolts, we found that increasing the initial preload could increase the axial force under the same conditions and the retarded anchoring section could control the axial-force loss of bolts in the middle of the anchoring section. Under the full-stress anchoring mode, the effect of applying a pre-tightening force was better than that of applying a pre-tightening force under traditional anchoring methods. Moreover, FLAC3D (Fast Lagrangian Analysis of Continua 3D; ITASCA (Ita sca International Inc), Minnesota, USA) numerical simulation calculation was performed. Under the full-stress anchoring mode of bolts, the increased anchoring length reduced the damage of the anchoring section, with a wider control range of the rock formation and higher strength of the compressive-stress anchoring zone. Based on the above research, four methods for applying the full-stress anchoring technology of bolts in engineering were proposed. The full-stress anchoring technology of bolts in the coal roadway has been applied in the support project of the return-air roadway at working face 3204 of the Taitou Coking Coal Mine of the Xiangning Coking Coal Group, Shanxi. The maximum moving distance of the roof and floor of the roadway was reduced from 200 to 42 mm, and the maximum moving distance on both coal sides was reduced from 330 to 86 mm. The full-stress anchoring technology of bolts was able to control the surrounding rock in the coal roadway. Full article

(This article belongs to the Special Issue Rock Burst Disasters in Coal Mines)

► Show Figures

Graphical abstract

15 pages, 8926 KiB

Open AccessArticle

An Approach to Dynamic Disaster Prevention in Strong Rock Burst Coal Seam under Multi-Aquifers: A Case Study of Tingnan Coal Mine

by Xinxin Zhou, Zhenhua Ouyang, Ranran Zhou, Zhenxing Ji, Haiyang Yi, Zhongyi Tang, Bo Chang, Chengcheng Yang and Bingcheng Sun

Energies 2021, 14(21), 7287; https://doi.org/10.3390/en14217287 - 03 Nov 2021

Cited by 11 | Viewed by 1385

Abstract

In order to prevent the multi-dynamic disasters induced by rock burst and roof water inrush in strong rock burst coal seams under multi-aquifers, such as is the case with the 207 working face in the Tingnan coal mine considered in this study, the exhibited characteristics of two types of dynamic disasters, namely rock burst and water inrush, were analyzed. Based on the lithology and predicted caving height of the roof, the contradiction between rock burst and water inrush was analyzed. In light of these analyses, an integrated method, roof pre-splitting at a high position and shattering at a low position, was proposed. According to the results of numerical modelling, pre-crack blasting at higher rock layers enables a cantilever roof cave in time, thereby reducing the risk of rock burst, and pre-crack blasting at underlying rock layers helps increase the crushing degree of the rock, which is beneficial for decreasing the caving height of rock layers above goaf, thereby preventing the occurrence of water inrush. Finally, the proposed method was applied in an engineering case, and the effectiveness of this method for prevention and control of multi-dynamics disasters was evaluated by field observations of the caving height of rock layers and micro-seismic monitoring. As a result, the proposed method works well integrally to prevent and control rock burst and water inrush. Full article

(This article belongs to the Special Issue Rock Burst Disasters in Coal Mines)

► Show Figures

Figure 1

15 pages, 14690 KiB

Open AccessArticle

Experimental Study on the Mechanical Behavior and Failure Characteristics of Layered Coal at Medium Strain Rates

by Kun Zhong, Wusheng Zhao, Changkun Qin and Weizhong Chen

Energies 2021, 14(20), 6616; https://doi.org/10.3390/en14206616 - 13 Oct 2021

Cited by 4 | Viewed by 1218

Abstract

The study of the mechanical properties and failure behaviors for coal with different bedding structures at various medium strain rates is of great importance for revealing the mechanism of rock burst. In our study, we systematically analyze the uniaxial compressive strength (UCS), acoustic emission (AE) characteristics, failure pattern, and risk of rock burst on coal specimens with two bedding orientations under ranged in strain rates from 10⁻⁴ s⁻¹ to 10⁻² s⁻¹. The results reflect that and the bedding direction and the strain rates significantly affect the UCS and failure modes of coal specimens. The UCS of coal specimens with loading directions perpendicular to bedding planes (horizontal bedding) increases logarithmically with increasing strain rate while the UCS increases first and then decreases of coal specimens with loading directions parallel to bedding planes (vertical bedding). The AE cumulative energy of the specimens with horizontal bedding is an order of magnitude higher than that of specimens with vertical bedding. However, it is independent of the strain rates. The energy release rates of these two types of bedded coal specimens increase in a power function as the strain rate increases. The coal specimens with horizontal bedding show violent failure followed by the ejection of fragments, indicating a high risk of rock burst. On the other hand, the coal specimens with vertical bedding exhibit a tensile splitting failure with a low risk of rock burst. Strain localization is a precursor of coal failure, and the concentration area of local principal strain is highly consistent with the initial damage area, and the area where the principal strain gradient is significantly increased corresponds to the fracture initiation area. Full article

(This article belongs to the Special Issue Rock Burst Disasters in Coal Mines)

► Show Figures

Figure 1

19 pages, 8612 KiB

Open AccessArticle

Instability Control of Roadway Surrounding Rock in Close-Distance Coal Seam Groups under Repeated Mining

by Yu Xiong, Dezhong Kong, Zhanbo Cheng, Zhijie Wen, Zhenqian Ma, Guiyi Wu and Yong Liu

Energies 2021, 14(16), 5193; https://doi.org/10.3390/en14165193 - 22 Aug 2021

Cited by 16 | Viewed by 2498

Abstract

In order to solve the problems of roadway stability and easy instability under repeated mining of close-distance coal seam groups, the mechanism and control technology of surrounding rock instability under repeated mining were studied via indoor testing, field testing, physical similarity simulation experiment, and numerical simulation. The results show that the surrounding rock of roadway has low strength, low bearing capacity, and poor self-stabilization ability, and it is vulnerable to engineering disturbances and fragmentation. Affected by the disturbance under repeated mining, the roadway surrounding rock cracks are developed and the sensitivity is strong, and it is prone to large-scale loose and destroyed. The location of the roadway is unreasonable, and the maximum principal stress of the roadway is 3.1 times of the minimum principal stress, which is quite different. Thus, under a large horizontal stress, the surrounding rock undergoes long-range expansion deformation. On the basis of this research, the direction and emphasis of stability control of roadway surrounding rock under repeated mining of coal seam groups in close-distance are shown. A repair scheme (i.e., long bolt + high-strength anchor cable + U-shaped steel + grouting) is proposed, and reduces the risk of roadway instability. Full article

(This article belongs to the Special Issue Rock Burst Disasters in Coal Mines)

► Show Figures

Figure 1

17 pages, 10760 KiB

Open AccessArticle

Longwall Top-Coal Caving Mechanism and Cavability Optimization with Hydraulic Fracturing in Thick Coal Seam: A Case Study

by Zhaohui Wang, Yuesong Tang and Hao Gong

Energies 2021, 14(16), 4832; https://doi.org/10.3390/en14164832 - 08 Aug 2021

Cited by 3 | Viewed by 1681

Abstract

Longwall top-coal caving mechanisms and cavability optimization with hydraulic fracturing are analysed in this study. Based on the geological and geotechnical conditions of the Dongzhouyao coal mine, it is revealed that top-coal failure mechanisms are dominated by both compressive and tensile stresses. Ahead of the face line, shear failure initiates at the lower level of the top-coal and propagates to the upper level. Compressive stress-induced damage leads to obvious deterioration in tensile strength, causing the onset of tensile failure in the top-coal behind the face line. Accumulated plastic strain (APS) is selected as a top-coal cavability indicator. The cavability degrades gradually at the higher elevation of the top-coal while it is greatly strengthened as the top-coal approaches closer to the face line. In a thick coal seam without hydraulic fractures, the maximum APS occurs at the middle section of the face length in the Longwall top-coal caving (LTCC) panel. After hydraulic fracturing, top-coal cavability is significantly enhanced. But the spatial distribution of the APS transitions from uniform to non-uniform type due to the existence of hydraulic fractures, causing great variety in the cavability along the panel width. With increasing fracture intensity and fracture size, the failure zone expands significantly ahead of the longwall face, which means the cavability becomes increasingly favourable. Full article

(This article belongs to the Special Issue Rock Burst Disasters in Coal Mines)

► Show Figures

Figure 1

16 pages, 20628 KiB

Open AccessArticle

Numerical Study on Strength and Failure Behavior of Rock with Composite Defects under Uniaxial Compression

by Xiaofei Wang, Zhiguo Xia, Peng Li and Hongning Liu

Energies 2021, 14(15), 4418; https://doi.org/10.3390/en14154418 - 22 Jul 2021

Cited by 12 | Viewed by 1666

Abstract

The cracks and holes in underground engineering are the critical factors that cause the instability of the surrounding rock. It is helpful to control the stability of surrounding rock to study the samples with combined defects of cracks and holes. In this study, PFC 2D is used to analyze the numerical models. Seven combined models of single circular hole and double cracks with different angles are established, and the fracture angle varies from 0° to 90° with an interval of 15°. First, uniaxial compression experiments and numerical simulations are carried out in the 0° defect combination model, and the microscopic parameters of PFC 2D are determined. Then, the numerical simulations of seven defect models under uniaxial compression are carried out, and the crack development law and acoustic emission characteristics of different defect combination models are studied. The failure modes, mechanical behavior, and stress states are studied. The displacement vector distributions of different defect combination models are analyzed; it is found that there are three main types of macro cracks in the defect combination samples. The results show that the combined defects reduce the strength of the model. Meanwhile, the distributions of the stress and displacement are changed by the cracks with different angles in the defective models. Full article

(This article belongs to the Special Issue Rock Burst Disasters in Coal Mines)

► Show Figures

Figure 1

Review

Jump to: Editorial, Research, Other

16 pages, 1012 KiB

Open AccessReview

Rockburst Precursors and the Dynamic Failure Mechanism of the Deep Tunnel: A Review

by Yulong Chen, Junwen Zhang, Jiahao Zhang, Bin Xu, Luji Zhang and Wenxin Li

Energies 2021, 14(22), 7548; https://doi.org/10.3390/en14227548 - 12 Nov 2021

Cited by 7 | Viewed by 2044

Abstract

With the rapid development of underground caverns in the fields of hydraulic engineering, mining, railway and highway, the frequency, and intensity of rockburst and dynamic instability have gradually increased, which has become a bottleneck restricting the safe construction of deep caverns. This paper presents a review of the current understanding of rockburst precursors and the dynamic failure mechanism of the deep tunnel. Emphasis is placed on the stability of the surrounding rock of the deep tunnel, the rockburst prediction method, and the dynamic failure characteristics of the surrounding rock of the deep tunnel. Throughout the presentation, the current overall gaps in understanding rockburst precursors and the dynamic failure mechanism of deep tunnels are identified in an attempt to stimulate further research in these promising directions by the research community. Full article

(This article belongs to the Special Issue Rock Burst Disasters in Coal Mines)

► Show Figures

Figure 1

Other

Jump to: Editorial, Research, Review

15 pages, 3763 KiB

Open AccessTechnical Note

Studying the Bond Performance of Full-Grouting Rock Bolts Based on the Variable Controlling Method

by Jianhang Chen, Ziwei Ding, Saisai Wu and Junwen Zhang

Energies 2022, 15(9), 3157; https://doi.org/10.3390/en15093157 - 26 Apr 2022

Cited by 1 | Viewed by 1272

Abstract

This paper studied the bond performance of full-grouting rock bolts with a theoretical analysis. The variable controlling method was used to study the effect of parameters on the load-carrying force of bars. The results showed that when the bar diameter grew from 15 mm to 25 mm, the maximum force of the bars rose from 194 kN to 349 kN, growing by 80%. As for the stiffness, it grew by 108%. Moreover, when the elastic modulus grew from 50 GPa to 200 GPa, the maximum force rose from 229 kN to 269 kN, only growing by 17%. As for the stiffness, it grew by 100%. When the grouting length increased from 2 m to 3 m, the maximum force rose from 269 kN to 364 kN, growing by 35%. However, the grouting length had almost no effect on the stiffness. Lastly, for the bond slip when the bond strength was reached, when it grew from 1 mm to 3 mm, the maximum force dropped from 281 kN to 258 kN, dropping by 8%. As for the stiffness, it dropped by 44%. This paper is conducive to enriching the base of knowledge. Full article

(This article belongs to the Special Issue Rock Burst Disasters in Coal Mines)

► Show Figures

Figure 1

Journal Menu

Journal Browser

Rock Burst Disasters in Coal Mines

Share This Special Issue

Special Issue Editors

Special Issue Information

Keywords

Published Papers (14 papers)

Editorial

Research

Review

Other

Further Information

Guidelines

MDPI Initiatives

Follow MDPI