Search Results (4,581)

To investigate the bending response of ultra-high-performance concrete (UHPC) beams reinforced with hybrid glass-fiber-reinforced polymer (GFRP) and steel bars, five specimens were tested in four-point bending in the present experimental study. The effect of varying reinforcement ratios on the flexural behavior was evaluated. It was observed that all tested beams failed due to reinforcement yielding while maintaining satisfactory ductility; the failure mode was characterized by yielding of the bottom tensile reinforcement followed by crushing of the UHPC in the compression zone. When the steel reinforcement ratio increased from 2.03% to 2.42% and 3.08%, the beam load-carrying capacity increased by 6.27% and 14.34%, respectively. When the GFRP reinforcement ratio increased from 0.91% to 1.19% and 1.51%, the peak load-carrying capacity increased by 9.58% and 15.55%, respectively. Based on reasonable assumptions, analytical formulas were proposed to predict the cracking moment and the flexural capacity of the UHPC beams reinforced with hybrid GFRP and steel bars, with errors within ±5%. By fully accounting for the bridging effect of steel fibers, modified coefficients were introduced to estimate beam deformation and crack width, along with corresponding calculation methods. The proposed formulas accurately predicted cracking moment, ultimate moment, deflection and crack width for the beam. The findings propose a theoretical basis for the design and application of UHPC beams reinforced with hybrid GFRP and steel bars. Full article

Shrinkage of injection-molded parts is a major challenge for dimensional accuracy, especially for semi-crystalline polymers where crystallization induces pronounced volume change and heat release during cooling. Because packing pressure is effective only before gate or local solidification, multi-stage packing is commonly used to regulate the overall shrinkage behavior. In practice, however, the solidification/transition temperature taken from standard material tests does not necessarily represent the actual in-cavity state behavior under specific cooling rate and pressure history, which compromises the consistency of P–V–T-based shrinkage prediction. In this study, a modified P–V–T-based framework (Tait equation) is developed for polypropylene (PP) by introducing a Thermal Enthalpy Transformation Method (TETM) to determine a process-relevant solidification time and crystallization-completion temperature (including the corresponding target specific volume) directly from in-cavity melt temperature monitoring using an infrared temperature sensor. The novelty TETM utilizes the crystallization-induced enthalpy release to identify the temperature–time plateau, from which one can identify the effective solidification point. Because the Tait equation adopts a two-domain formulation (molten and solidified states), accurate identification of the domain-switching temperature is critical for reliable shrinkage prediction in practical molding conditions. In the experiment execution, the optimum filling time was defined using the minimum pressure required for melt-filling. Four target specific volumes, three melt temperatures, and two mold temperatures were examined, and a two-stage packing strategy was implemented to achieve comparable shrinkage performance under different target specific volumes. A conventional benchmark based on the solidification temperature reported in the Moldex3D material database was used for comparison only. The results show that the target specific volume determined by the TETM exhibits a more consistent and near-linear relationship with the measured shrinkage rate, demonstrating that the TETM improves the robustness of solidification-time identification and the practical usability of P–V–T information for shrinkage control. Full article

Powder Injection Molding (PIM) is a versatile manufacturing technology widely used for fabricating components with complex geometries from metals and ceramics, yet its application to high-performance thermoplastics remains underutilized. This study explores the feasibility of manufacturing products from Polyphenylene Sulfide (PPS)—a promising linear aromatic polymer synthesized in powder form—using PIM technology and investigates the development of PE-based feedstocks with PPS and solid fillers. Regarding the matrix formulation, it was found that using pure paraffin as a binder limited the maximum PPS content to 20%. Consequently, a modified binder system consisting of Low-Density Polyethylene (LDPE) and paraffin in a 70:30 wt.% ratio was utilized, which successfully increased the PPS loading in the feedstock to 50% and enabled stable molding. Following matrix optimization, the study examined composites incorporating various fillers, including chalk, talc, and carbon fibers. Systematic rheological analysis confirmed that these composite suspensions possess characteristics necessary for molding products with complex geometries. Key results indicate that optimal sintering conditions were established to achieve the required mechanical properties. Among the tested fillers, carbon fibers were the most effective reinforcement, increasing the elastic modulus by 33% and flexural strength by 20%. Representative examples of samples successfully manufactured via this approach are presented. Full article

This research investigates the effects of corona plasma treatment on the mechanical properties of jute/epoxy-reinforced composites, particularly within biomedical application contexts. Plant Fibre Composites (PFCs) are attractive for medical devices and scaffolds due to their environmental friendliness, renewability, cost-effectiveness, low density, and high specific strength. However, their applications are often constrained by inferior mechanical performance arising from poor bonding between the plant fibre used as the reinforcement and the synthetic resin or polymer serving as the matrix. This study addresses the challenge of improving the weak interfacial bonding between plant fibre and synthetic resin in a 2/2 twill-weave-woven jute/epoxy composite material. The surface of the jute fibre is modified for better adhesion with the epoxy resin through plasma treatment, which exposes the jute fibre to controlled plasma energy and utilises dry air (plasma only), argon (Ar) (argon gas with plasma), and nitrogen (N₂) (nitrogen gas with plasma) at two different distances (25 mm and 35 mm) between the plasma nozzle and the fibre surface. In this context, “equilibrium” refers to the optimal combination of plasma power, treatment distance, and gas environment that collectively determines the degree of fibre surface modification. The results indicate that all plasma treatments improve the interlaminar shear strength in comparison to untreated samples, with treatments at 35 mm using N₂ gas showing a 35.4% increase in shear strength. Conversely, plasma treatment using dry air at 25 mm yields an 18.3% increase in tensile strength and a 35.7% increase in Young’s modulus. These findings highlight the importance of achieving an appropriate equilibrium among plasma intensity, treatment distance, and fibre–plasma interaction conditions to maximise the effectiveness of plasma treatment for jute/epoxy composites. This research advances sustainable innovation in biomedical materials, underscoring the potential for improved mechanical properties in environmentally friendly fibre-reinforced composites. Full article

Christmas tree growers are concerned with improving establishment of their plantations. Here, we report the results of a series of on-farm trials conducted with grower-cooperators in the Pacific Northwest (PNW) and Great Lakes (Michigan—MI) regions to determine the efficacy of treatments at planting on improving tree survival and growth in Christmas tree plantations. Cooperating growers planted species that were typical for each region (Fraser fir in the Great Lakes and Douglas-fir and noble fir in the PNW) and managed the plantings using standard cultural practices, aside from test treatments. Test treatments varied between locations and years but included wood chip mulch, shade blocks, an anti-transpirant, biochar, fertilizers, and various root dips including polymer gels, mycorrhizae, and bio-stimulants. Overall, treatments that directly modified the tree environment (i.e., mulch and shade blocks) provided the most consistent benefit to tree survival and growth. In Michigan, mulching increased survival by 5% on non-irrigated farms and increased second-year shoot growth by ~3 cm. In the PNW trials, mulching increased survival of noble fir seedlings more than Douglas-fir seedlings. Installing controlled release fertilizer packets at planting increased initial growth of Douglas-firs. Application of root dips prior to planting did not improve tree survival or growth relative to dipping tree roots in water (control). Based on our results, we conclude that treatments that conserve soil moisture (mulch) or reduce tree water loss (shade blocks) offer the most direct opportunity for growers to improve initial tree survival and growth. Full article

In this study, semi-interpenetrating polymer network (semi-IPN) hydrogels based on methacrylated dextran and native inulin were designed as biodegradable carriers for the colon-specific delivery of uracil as a model antitumor compound. The hydrogels were synthesized via free-radical polymerization, using diethylene glycol diacrylate (DEGDA) as a crosslinking agent at varying concentrations (5, 7.5, and 10 wt%), and their structural, thermal, and biological properties were systematically evaluated. Fourier transform infrared spectroscopy (FTIR) confirmed successful crosslinking and physical incorporation of uracil through hydrogen bonding. Concurrently, differential scanning calorimetry (DSC) revealed an increase in glass transition temperature (T_g) with increasing crosslinking density (149, 153, and 156 °C, respectively). Swelling studies demonstrated relaxation-controlled, first-order swelling kinetics under physiological conditions (pH 7.4, 37 °C) and high gel fraction values (84.75, 91.34, and 94.90%, respectively), indicating stable network formation. SEM analysis revealed that the hydrogel morphology strongly depended on crosslinking density and drug incorporation, with increasing crosslinker content leading to a more compact and wrinkled structure. Uracil loading further modified the microstructure, promoting the formation of discrete crystalline domains within the semi-IPN hydrogels, indicative of physical drug entrapment. All formulations exhibited high encapsulation efficiencies (>86%), which increased with increasing crosslinker content, consistent with the observed gel fraction values. Simulated in vitro gastrointestinal digestion showed negligible drug release under gastric conditions and controlled release in the intestinal phase, primarily governed by crosslinking density. Antimicrobial assessment against Escherichia coli and Staphylococcus epidermidis, used as an initial or indirect indicator of cytotoxic potential, revealed no inhibitory activity, suggesting low biological reactivity at the screening level. Overall, the results indicate that DEGDA-crosslinked dextran/inulin semi-interpenetrating (semi-IPN) hydrogels represent promising carriers for colon-targeted antitumor drug delivery. Full article

Dopamine (DA) is a critical catecholaminergic neurotransmitter that facilitates signal transduction across synaptic junctions and modulates essential neurophysiological processes, including motor coordination, motivational drive, and reward-motivated behaviors. The fabrication of cost-effective, miniaturized, and high-fidelity analytical platforms is imperative for real-time DA monitoring. Due to its inherent electrochemical activity, carbon-based amperometric sensors constitute the primary modality for DA quantification. In this study, graphite, multi-walled carbon nanotubes (MWCNTs), and graphene were immobilized within an ethyl 2-cyanoacrylate (ECA) polymer matrix. ECA was selected for its rapid polymerization kinetics and established biocompatibility in electrochemical frameworks. All fabricated composites demonstrated robust electrocatalytic activity toward DA; however, MWCNT- and graphene-based sensors exhibited superior analytical performance, characterized by highly competitive limits of detection (LOD) and quantification (LOQ). Specifically, MWCNT-modified electrodes achieved an interesting LOD of 0.030 ± 0.001 µM and an LOQ of 0.101 ± 0.008 µM. Discrepancies in baseline current amplitudes suggest that the spatial orientation of carbonaceous nanomaterials within the cyanoacrylate matrix significantly influences the electrochemical surface area and resulting baseline characteristics. The impact of interfering species commonly found in biological environments on the sensors’ response was systematically evaluated. The best-performing sensor, the graphene-based one, was used to measure the DA intracellular content of PC12 cells. Full article

The irrational or excessive use of antibiotics causes the emergence of bacterial resistance, making antibiotics less effective or ineffective. As the number of resistant antibiotics increases, it is crucial to develop new strategies and innovative approaches to potentiate the efficacy of existing antibiotics. Prior to this, we discovered that some of the traditional antibiotics produce reactive oxygen species (ROS) under specific light exposure. In this paper, we report a multifunctional polymeric nanoparticle (F8IC NPs-PME) that combines targeted and photodynamic–photothermal therapy (PDT-PTT) in one device. The PME on the surface of F8IC enables the selective binding of F8IC NPs-PME to the surface of Gram-negative bacteria. In addition, PME and F8IC can generate ROS and photothermia under near-infrared light excitation, respectively. The results showed that the sterilization efficiency of F8IC NPs-PME at a concentration of 8 μg/mL was as high as 94.7% against kanamycin-resistant E. coli under 808 nm near-infrared light irradiation (0.8 W/cm², 10 min). This antimicrobial strategy can achieve efficient bacteria killing with a low dosage of antibiotics and opens up a new avenue for fighting bacterial resistance. Full article

Traditional flexible polyurethane (PU) foams frequently exhibit limited mechanical support and suboptimal moisture–heat regulation, which can compromise the microenvironmental comfort required for high-quality sleep. In this study, natural luffa fibers (LF) were incorporated as a microstructural modifier to simultaneously enhance the mechanical and moisture–heat regulation performance of PU foams. PU/LF composite foams with varying LF loadings were prepared via in situ polymerization, and their foaming kinetics, cellular morphology evolution, and physicochemical characteristics were systematically investigated. The results indicate that LF functions both as a reinforcing skeleton and as a heterogeneous nucleation site, thereby promoting more uniform bubble formation and controlled open-cell development. At an optimal loading of 4 wt%, the composite foam developed a highly interconnected porous architecture, leading to a 7.9% increase in tensile strength and improvements of 19.4% and 22.6% in moisture absorption and moisture dissipation rates, respectively, effectively alleviating the heat–moisture accumulation typically observed in unmodified PU foams. Ergonomic pillow prototypes fabricated from the optimized composite further exhibited enhanced pressure-relief performance, as evidenced by reduced peak cervical pressure and improved uniformity of contact-area distribution in human–pillow pressure mapping, together with an increased SAG factor, indicating improved load-bearing adaptability under physiological sleep postures. Collectively, these findings elucidate the microstructural regulatory role of biomass-derived luffa fibers within porous polymer matrices and provide a robust material basis for developing high-performance, sustainable, and ergonomically optimized sleep products. Full article

The mitigation of traffic noise is essential for the development of sustainable and livable urban environments, a goal that is directly contingent on addressing tire-pavement interaction noise (TPIN) as the dominant acoustic pollutant at medium to high vehicle speeds. This comprehensive review addresses a critical gap in the literature by systematically analyzing the damping properties of pavement systems through a unified, multi-scale framework—from the molecular-scale viscoelasticity of asphalt binders to the composite performance of asphalt mixtures. The analysis begins by synthesizing state-of-the-art testing and characterization methodologies, which establish a clear connection between macroscopic damping performance and the underlying viscoelastic mechanisms coupled with the microscopic morphology of the binders. Subsequently, the review critically assesses the influence of critical factors, such as polymer modifiers including rubber and Styrene-Butadiene-Styrene (SBS), temperature, and loading frequency. This examination elucidates how these variables govern molecular mobility and relaxation processes to ultimately determine damping efficacy. A central and synthesizing conclusion emphasizes the paramount importance of the asphalt binder’s properties, which serve as the primary determinant of the composite mixture’s overall acoustic performance. By delineating this structure-property-performance relationship across different scales, the review consolidates a foundational scientific framework to guide the rational design and informed material selection for next-generation asphalt pavements. The insights presented not only advance the fundamental understanding of damping mechanisms in pavement materials but also provide actionable strategies for creating quieter and more sustainable transportation infrastructures. Full article

Polymeric microfiltration membranes are among the most utilized pressure-driven membranes due to their excellent permeation flux, moderate removal efficiency, low operating pressure, low cost, as well as their potential for reusability and cleanability. Therefore, these membranes are used in different crucial sectors, including the water and wastewater, dairy, beverage, and pharmaceutical industries. However, well-known polymeric microfiltration membranes suffer from their poor hydrophilic properties, causing fouling phenomenon. A reduction in permeate flux, a shortened operational lifespan, and increased energy consumption are the primary negative consequences of membrane fouling. Over the years, a broad spectrum of studies has been performed to modify polymeric microfiltration membranes to improve their hydrophilic, transport, and antifouling characteristics. Despite extensive research, this issue remains a subject of ongoing discussion and scrutiny within the scientific community. This review article provides promising information about different physical and chemical modification methods—such as polymer blending, the incorporation of nanomaterials, surface coating, chemical crosslinking, in situ nanoparticle immobilization, and chemical surface functionalization—for polymeric microfiltration membranes. The physical and chemical modification methods are comparatively evaluated, highlighting their positive and negative aspects, supported by findings from recent investigations. Moreover, promising ideas and future-oriented techniques were proposed to obtain polymeric microfiltration membranes containing superior efficiency, extended service life, and mechanical strength. Full article

Additive manufacturing has been widely adopted in industry as an alternative to traditional manufacturing processes for complex component production. In fact, a diverse range of materials, particularly polymers, can be processed using 3D printing for biomechanical applications (e.g., prosthetics). However, in-depth evaluation of these materials is necessary to determine their suitability for demanding applications, such as those involving cyclic loading. Following previous work that studied Polylactic Acid (PLA) and Polyethylene Terephthalate Glycol-modified (PETG) under experimental fatigue testing, this study examines the fatigue behaviour of other current 3D-printed polymeric materials, namely Acrylonitrile Styrene Acrylate (ASA), Polycarbonate (PC), Polyamide 12 (Nylon 12), and Polycarbonate–Acrylonitrile Butadiene Styrene (blend) (PC-ABS), for which fatigue data remain limited or even non-existent. The findings revealed performance differences on Tensile Strength (σ_R), Young’s Modulus and Ultimate Strain among tensile specimens made from these materials and characterised S-N curves for both high-cycle (HCF) and low-cycle (LCF) fatigue regimes at room temperature, with a tensile load ratio (R = 0.05). These results establish relationships among fatigue limit and quasi-static mechanical properties, namely 25% × σ_r for ASA (8 MPa), 7% × σ_r for PC (3.6 MPa), 17% × σ_r for Nylon 12 (7.4 MPa), and 15% × σ_r for PC-ABS (4.7 MPa), as well as between mechanical properties and preliminary potential biomechanical applications. Main conclusions were further supported by micro-computed tomography (micro-CT), which revealed levels of porosity in between 4% and 11%, thermogravimetric analysis (TGA), differential scanning calorimetry (DSC), and Fourier transform infrared spectroscopy (FTIR). Full article

Concrete production contributes approximately 4–8% of global cardon dioxide emissions, largely due to Portland cement. Incorporating municipal solid waste (MSW) into concrete offers a pathway to reduce cement demand while supporting circular economy objectives. This study evaluates the mechanical performance, environmental impacts, and optimization potential of concrete incorporating three MSW-derived materials: cardboard kraft fibers (KFs), recycled high-density polyethylene (HDPE), and textile fibers. A maximum 10% cement replacement strategy was adopted. Compressive strength was assessed at 7, 14, and 28 days, and a cradle-to-gate life cycle assessment (LCA) was conducted using OpenLCA to quantify global warming potential (GWP100) and other midpoint impacts. A surrogate-based optimization implemented using Non-dominated Sorting Genetic Algorithm II (NSGA-II) was applied to minimize cost and GWP while enforcing compressive strength as a feasibility constraint. The results show that fiber-based wastes significantly reduce embodied carbon, with KF achieving the largest GWP reduction (19%) and textile waste achieving moderate reductions (10%) relative to the control. HDPE-modified concrete exhibited near-control mechanical performance but increased GWP and fossil depletion due to polymer processing burdens. The optimization results revealed well-defined Pareto trade-offs for KF and textile concretes, identifying clear compromise solutions between cost and emissions, while HDPE was consistently dominated. Overall, textile waste emerged as the most balanced option, offering favorable environmental gains with minimal cost and acceptable mechanical performance. The integrated LCA optimization framework demonstrates a robust approach for evaluating MSW-derived concrete and supports evidence-based decision-making toward low-carbon, circular construction materials. Full article

Alzheimer’s disease (AD) is a progressive neurodegenerative disorder marked by persistent memory impairment and complex molecular and cellular pathological changes in the brain. Current treatments, including acetylcholinesterase inhibitors and memantine, only help with symptoms for a short time and do not stop the disease from getting worse. This is mainly because these drugs do not reach the brain well and are quickly removed from the body. The blood–brain barrier (BBB) restricts the entry of most drugs into the central nervous system; therefore, new methods of drug delivery are needed. Nanotechnology-based drug delivery systems (NTDDS) are widely studied as a potential approach to address existing therapeutic limitations. Smart biosensing nanoparticles composed of polymers, lipids, and metals can be engineered to enhance drug stability, improve drug availability, and target specific brain regions. These smart nanoparticles can cross the BBB via receptor-mediated transcytosis and other transport routes, making them a promising option for treating AD. Additionally, multifunctional nanocarriers enable controlled drug release and offer theranostic capabilities, supporting real-time tracking of AD treatment responses to facilitate more precise and personalized interventions. Despite these advantages, challenges related to long-term safety, manufacturing scalability, and regulatory approval remain. This review discusses current AD therapies, drug-delivery strategies, recent advances in nanoparticle platforms, and prospects for translating nanomedicine into effective, disease-modifying treatments for AD. Full article

Conductive polymers (CPs), such as polypyrrole (PPy), have shown promising properties for use as electro-responsive bioactive scaffolds for tissue regeneration. PPy can be synthesized by chemical electrosynthesis and doped with biomolecules such as hyaluronic acid (HA). Taking advantage of the electrochemical synthesis versatility, nanofibers for surface-modified indium tin oxide (ITO) electrodes can be used as templates to produce tridimensional HA-doped PPy scaffolds. In this study, polyvinyl alcohol/chitosan (PVA/CTS) electrospun nanofibers deposited on ITO electrodes were used as a 3D template for the in situ electrosynthesis of HA-doped PPy to produce a bioactive scaffold for tissue engineering. The final material gathers the advantages of each biopolymer, the porous morphology of the nanofiber, and the conductivity of the electrosynthetized polymer. Furthermore, the biological activity of the NF-PVA/CTS@PPy:HA composite was evaluated in NIH-3T3 fibroblasts by MTT, resulting in a cell viability of 146 ± 40% and wound-healing capacity of 97 ± 1.9% at 24 h of culture. Full article