Electrical and Electro-Optical Biosensors

A special issue of Biosensors (ISSN 2079-6374). This special issue belongs to the section "Biosensor and Bioelectronic Devices".

Deadline for manuscript submissions: closed (15 September 2021) | Viewed by 42353

Printed Edition Available!
A printed edition of this Special Issue is available here.

Special Issue Editors


E-Mail Website
Guest Editor
Department of Bioscience Technology and Department of Medical Sciences Industry, Chang Jung Christian University, Tainan, Taiwan
Interests: biosensors; liquid crystal; cancer biomarker; aptamer; stem cells; nanobiomaterials

E-Mail Website
Guest Editor
Department of Electrical and Computer Engineering, School of Engineering, Baylor University, Waco, TX 76798, USA
Interests: biosensors; optical biosensors; microfabrication; photonics; microfluidic devices; integrated optics

Special Issue Information

Dear colleagues,

Electrical and electro-optical biosensors have received much attention in recent years because of their sensitive detection, simplified procedure, and potential in the development of portable point-of-care devices. These technologies generally rely on the label-free detection of the electrical, electrochemical, and electro-optical signals derived from molecular interactions on sensor surfaces modified with biomolecules. Innovative application of voltammetric, amperometric, capacitance measurements, electrochemical impedance spectroscopy, electrochemical surface plasmon resonance, electrochemical optical waveguide lightmode spectroscopy, transmission spectrometry and dielectric spectrometry on the detection and quantitation of disease-related biomarkers, molecular interactions and activity assays offers challenging research topics yet promising perspectives for researchers working in the field of biosensors.

This Special Issue is devoted to the recent advances in electrical, electrochemical, and electro-optical biosensors, including the design of the electrode and biosensing interfaces, as well as the quantitative approaches for interpreting various electrical signals resulting from the detection of target analytes or molecular binding events. The authors are encouraged to provide clinical evidence or implications that these technologies can be potentially transformed into practical medical devices.

Prof. Dr. Mon-Juan Lee

Dr. Seunghyun Kim
Guest Editors

Manuscript Submission Information

Manuscripts should be submitted online at www.mdpi.com by registering and logging in to this website. Once you are registered, click here to go to the submission form. Manuscripts can be submitted until the deadline. All submissions that pass pre-check are peer-reviewed. Accepted papers will be published continuously in the journal (as soon as accepted) and will be listed together on the special issue website. Research articles, review articles as well as short communications are invited. For planned papers, a title and short abstract (about 100 words) can be sent to the Editorial Office for announcement on this website.

Submitted manuscripts should not have been published previously, nor be under consideration for publication elsewhere (except conference proceedings papers). All manuscripts are thoroughly refereed through a single-blind peer-review process. A guide for authors and other relevant information for submission of manuscripts is available on the Instructions for Authors page. Biosensors is an international peer-reviewed open access monthly journal published by MDPI.

Please visit the Instructions for Authors page before submitting a manuscript. The Article Processing Charge (APC) for publication in this open access journal is 2700 CHF (Swiss Francs). Submitted papers should be well formatted and use good English. Authors may use MDPI's English editing service prior to publication or during author revisions.

Keywords

  • electrical biosensor
  • electrochemical biosensor
  • electro-optical biosensor
  • dielectric biosensor
  • Protein
  • enzyme
  • Immunoassay
  • label-free detection
  • real-time detection
  • lab-on-a-chip devices

Benefits of Publishing in a Special Issue

  • Ease of navigation: Grouping papers by topic helps scholars navigate broad scope journals more efficiently.
  • Greater discoverability: Special Issues support the reach and impact of scientific research. Articles in Special Issues are more discoverable and cited more frequently.
  • Expansion of research network: Special Issues facilitate connections among authors, fostering scientific collaborations.
  • External promotion: Articles in Special Issues are often promoted through the journal's social media, increasing their visibility.
  • e-Book format: Special Issues with more than 10 articles can be published as dedicated e-books, ensuring wide and rapid dissemination.

Further information on MDPI's Special Issue polices can be found here.

Published Papers (10 papers)

Order results
Result details
Select all
Export citation of selected articles as:

Editorial

Jump to: Research, Review

3 pages, 168 KiB  
Editorial
A Label-Free and Affordable Solution to Point-of-Care Testing Devices
by Mon-Juan Lee
Biosensors 2022, 12(4), 192; https://doi.org/10.3390/bios12040192 - 24 Mar 2022
Viewed by 1639
Abstract
Clinical diagnosis and disease monitoring often require the detection of small-molecule analytes and disease-related proteins in body fluids [...] Full article
(This article belongs to the Special Issue Electrical and Electro-Optical Biosensors)

Research

Jump to: Editorial, Review

12 pages, 1660 KiB  
Article
Dielectrophoretic and Electrical Impedance Differentiation of Cancerous Cells Based on Biophysical Phenotype
by Ina Turcan, Iuliana Caras, Thomas Gabriel Schreiner, Catalin Tucureanu, Aurora Salageanu, Valentin Vasile, Marioara Avram, Bianca Tincu and Marius Andrei Olariu
Biosensors 2021, 11(10), 401; https://doi.org/10.3390/bios11100401 - 17 Oct 2021
Cited by 13 | Viewed by 2949
Abstract
Here, we reported a study on the detection and electrical characterization of both cancer cell line and primary tumor cells. Dielectrophoresis (DEP) and electrical impedance spectroscopy (EIS) were jointly employed to enable the rapid and label-free differentiation of various cancer cells from normal [...] Read more.
Here, we reported a study on the detection and electrical characterization of both cancer cell line and primary tumor cells. Dielectrophoresis (DEP) and electrical impedance spectroscopy (EIS) were jointly employed to enable the rapid and label-free differentiation of various cancer cells from normal ones. The primary tumor cells that were collected from two colorectal cancer patients, cancer cell lines (SW-403, Jurkat, and THP-1), and healthy peripheral blood mononuclear cells (PBMCs) were trapped first at the level of interdigitated microelectrodes with the help of dielectrophoresis. Correlation of the cells dielectric characteristics that was obtained via electrical impedance spectroscopy (EIS) allowed evident differentiation of the various types of cell. The differentiations were assigned to a “dielectric phenotype” based on their crossover frequencies. Finally, Randles equivalent circuit model was employed for highlighting the differences with regard to a series group of charge transport resistance and constant phase element for cancerous and normal cells. Full article
(This article belongs to the Special Issue Electrical and Electro-Optical Biosensors)
Show Figures

Figure 1

13 pages, 2448 KiB  
Article
Design and Analysis of a Single System of Impedimetric Biosensors for the Detection of Mosquito-Borne Viruses
by Fahmida Nasrin, Kenta Tsuruga, Doddy Irawan Setyo Utomo, Ankan Dutta Chowdhury and Enoch Y. Park
Biosensors 2021, 11(10), 376; https://doi.org/10.3390/bios11100376 - 7 Oct 2021
Cited by 11 | Viewed by 2913
Abstract
The treatment for mosquito-borne viral diseases such as dengue virus (DENV), zika virus (ZIKV), and chikungunya virus (CHIKV) has become difficult due to delayed diagnosis processes. In addition, sharing the same transmission media and similar symptoms at the early stage of infection of [...] Read more.
The treatment for mosquito-borne viral diseases such as dengue virus (DENV), zika virus (ZIKV), and chikungunya virus (CHIKV) has become difficult due to delayed diagnosis processes. In addition, sharing the same transmission media and similar symptoms at the early stage of infection of these diseases has become more critical for early diagnosis. To overcome this, a common platform that can identify the virus with high sensitivity and selectivity, even for the different serotypes, is in high demand. In this study, we have attempted an electrochemical impedimetric method to detect the ZIKV, DENV, and CHIKV using their corresponding antibody-conjugated sensor electrodes. The significance of this method is emphasized on the fabrication of a common matrix of gold–polyaniline and sulfur, nitrogen-doped graphene quantum dot nanocomposites (Au-PAni-N,S-GQDs), which have a strong impedimetric response based only on the conjugated antibody, resulting in minimum cross-reactivity for the detection of various mosquito-borne viruses, separately. As a result, four serotypes of DENV and ZIKV, and CHIKV have been detected successfully with an LOD of femtogram mL−1. Full article
(This article belongs to the Special Issue Electrical and Electro-Optical Biosensors)
Show Figures

Figure 1

14 pages, 3441 KiB  
Article
A Single-Substrate Biosensor with Spin-Coated Liquid Crystal Film for Simple, Sensitive and Label-Free Protein Detection
by Po-Chang Wu, Chao-Ping Pai, Mon-Juan Lee and Wei Lee
Biosensors 2021, 11(10), 374; https://doi.org/10.3390/bios11100374 - 6 Oct 2021
Cited by 6 | Viewed by 2486
Abstract
A liquid crystal (LC)-based single-substrate biosensor was developed by spin-coating an LC thin film on a dimethyloctadecyl[3-(trimethoxysilyl)propyl]ammonium chloride (DMOAP)-decorated glass slide. Compared with the conventional sandwiched cell configuration, the simplified procedure for the preparation of an LC film allows the film thickness to [...] Read more.
A liquid crystal (LC)-based single-substrate biosensor was developed by spin-coating an LC thin film on a dimethyloctadecyl[3-(trimethoxysilyl)propyl]ammonium chloride (DMOAP)-decorated glass slide. Compared with the conventional sandwiched cell configuration, the simplified procedure for the preparation of an LC film allows the film thickness to be precisely controlled by adjusting the spin rate, thus eliminating personal errors involved in LC cell assembly. The limit of detection (LOD) for bovine serum albumin (BSA) was lowered from 10−5 g/mL with a 4.2-μm-thick sandwiched cell of the commercial LC E7 to 107 g/mL with a 4.2-μm-thick spin-coated E7 film and further to 108 g/mL by reducing the E7 film thickness to 3.4 μm. Moreover, by exploiting the LC film of the highly birefringent nematic LC HDN in the immunodetection of the cancer biomarker CA125, an LOD comparable to that determined with a sandwiched HDN cell was achieved at 10−8 g/mL CA125 using a capture antibody concentration an order of magnitude lower than that in the LC cell. Our results suggest that employing spin-coated LC film instead of conventional sandwiched LC cell provides a more reliable, reproducible, and cost-effective single-substrate platform, allowing simple fabrication of an LC-based biosensor for sensitive and label-free protein detection and immunoassay. Full article
(This article belongs to the Special Issue Electrical and Electro-Optical Biosensors)
Show Figures

Figure 1

14 pages, 4558 KiB  
Article
Millimeter-Wave-Based Spoof Localized Surface Plasmonic Resonator for Sensing Glucose Concentration
by Yelim Kim, Ahmed Salim and Sungjoon Lim
Biosensors 2021, 11(10), 358; https://doi.org/10.3390/bios11100358 - 28 Sep 2021
Cited by 14 | Viewed by 2797
Abstract
Glucose-monitoring sensors are necessary and have been extensively studied to prevent and control health problems caused by diabetes. Spoof localized surface plasmon (LSP) resonance sensors have been investigated for chemical sensing and biosensing. A spoof LSP has similar characteristics to an LSP in [...] Read more.
Glucose-monitoring sensors are necessary and have been extensively studied to prevent and control health problems caused by diabetes. Spoof localized surface plasmon (LSP) resonance sensors have been investigated for chemical sensing and biosensing. A spoof LSP has similar characteristics to an LSP in the microwave or terahertz frequency range but with certain advantages, such as a high-quality factor and improved sensitivity. In general, microwave spoof LSP resonator-based glucose sensors have been studied. In this study, a millimeter-wave-based spoof surface plasmonic resonator sensor is designed to measure glucose concentrations. The millimeter-wave-based sensor has a smaller chip size and higher sensitivity than microwave-frequency sensors. Therefore, the microfluidic channel was designed to be reusable and able to operate with a small sample volume. For alignment, a polydimethylsiloxane channel was simultaneously fabricated using a multilayer bonding film to attach the upper side of the pattern, which is concentrated in the electromagnetic field. This real-time sensor detects the glucose concentration via changes in the S11 parameter and operates at 28 GHz with an average sensitivity of 0.015669 dB/(mg/dL) within the 0–300 mg/dL range. The minimum detectable concentration and the distinguishable signal are 1 mg/dL and 0.015669 dB, respectively, from a 3.4 μL sample. The reusability and reproducibility were assessed through replicates. Full article
(This article belongs to the Special Issue Electrical and Electro-Optical Biosensors)
Show Figures

Figure 1

15 pages, 40335 KiB  
Article
Label-Free Detection and Spectrometrically Quantitative Analysis of the Cancer Biomarker CA125 Based on Lyotropic Chromonic Liquid Crystal
by Hassanein Shaban, Mon-Juan Lee and Wei Lee
Biosensors 2021, 11(8), 271; https://doi.org/10.3390/bios11080271 - 11 Aug 2021
Cited by 10 | Viewed by 3055
Abstract
Compared with thermotropic liquid crystals (LCs), the biosensing potential of lyotropic chromonic liquid crystals (LCLCs), which are more biocompatible because of their hydrophilic nature, has scarcely been investigated. In this study, the nematic phase, a mesophase shared by both thermotropic LCs and LCLCs, [...] Read more.
Compared with thermotropic liquid crystals (LCs), the biosensing potential of lyotropic chromonic liquid crystals (LCLCs), which are more biocompatible because of their hydrophilic nature, has scarcely been investigated. In this study, the nematic phase, a mesophase shared by both thermotropic LCs and LCLCs, of disodium cromoglycate (DSCG) was employed as the sensing mesogen in the LCLC-based biosensor. The biosensing platform was constructed so that the LCLC was homogeneously aligned by the planar anchoring strength of polyimide, but was disrupted in the presence of proteins such as bovine serum albumin (BSA) or the cancer biomarker CA125 captured by the anti-CA125 antibody, with the level of disturbance (and the optical signal thus produced) predominated by the amount of the analyte. The concentration- and wavelength-dependent optical response was analyzed by transmission spectrometry in the visible light spectrum with parallel or crossed polarizers. The concentration of CA125 can be quantified with spectrometrically derived parameters in a linear calibration curve. The limit of detection for both BSA and CA125 of the LCLC-based biosensor was superior or comparable to that of thermotropic LC-based biosensing techniques. Our results provide, to the best of our knowledge, the first evidence that LCLCs can be applied in spectrometrically quantitative biosensing. Full article
(This article belongs to the Special Issue Electrical and Electro-Optical Biosensors)
Show Figures

Figure 1

15 pages, 3809 KiB  
Article
Signal Amplification in an Optical and Dielectric Biosensor Employing Liquid Crystal-Photopolymer Composite as the Sensing Medium
by Hassanein Shaban, Shih-Chun Yen, Mon-Juan Lee and Wei Lee
Biosensors 2021, 11(3), 81; https://doi.org/10.3390/bios11030081 - 13 Mar 2021
Cited by 10 | Viewed by 2742
Abstract
An optical and dielectric biosensor based on a liquid crystal (LC)–photopolymer composite was established in this study for the detection and quantitation of bovine serum albumin (BSA). When the nematic LC E7 was doped with 4-wt.% NOA65, a photo-curable prepolymer, and photopolymerized by [...] Read more.
An optical and dielectric biosensor based on a liquid crystal (LC)–photopolymer composite was established in this study for the detection and quantitation of bovine serum albumin (BSA). When the nematic LC E7 was doped with 4-wt.% NOA65, a photo-curable prepolymer, and photopolymerized by UV irradiation at 20 mW/cm2 for 300 s, the limit of detection determined by image analysis of the LC optical texture and dielectric spectroscopic measurements was 3400 and 88 pg/mL for BSA, respectively, which were lower than those detected with E7 alone (10 μg/mL BSA). The photopolymerized NOA65, but not the prepolymer prior to UV exposure, contributed to the enhanced optical signal, and UV irradiation of pristine E7 in the absence of NOA65 had no effect on the optical texture. The effective tilt angle θ, calculated from the real-part dielectric constant ε’, decreased with increasing BSA concentration, providing strong evidence for the correlation of photopolymerized NOA65 to the intensified disruption in the vertically oriented LC molecules to enhance the optical and dielectric signals of BSA. The optical and dielectric anisotropy of LCs and the photo-curable dopant facilitate novel quantitative and signal amplification approaches to potential development of LC-based biosensors. Full article
(This article belongs to the Special Issue Electrical and Electro-Optical Biosensors)
Show Figures

Figure 1

8 pages, 1129 KiB  
Communication
Highly Sensitive Detection of CA 125 Protein with the Use of an n-Type Nanowire Biosensor
by Kristina A. Malsagova, Tatyana O. Pleshakova, Rafael A. Galiullin, Andrey F. Kozlov, Ivan D. Shumov, Vladimir P. Popov, Fedor V. Tikhonenko, Alexander V. Glukhov, Vadim S. Ziborov, Oleg F. Petrov, Vladimir E. Fortov, Alexander I. Archakov and Yuri D. Ivanov
Biosensors 2020, 10(12), 210; https://doi.org/10.3390/bios10120210 - 18 Dec 2020
Cited by 13 | Viewed by 3168
Abstract
The detection of CA 125 protein in a solution using a silicon-on-insulator (SOI)-nanowire biosensor with n-type chip has been experimentally demonstrated. The surface of nanowires was modified by covalent immobilization of antibodies against CA 125 in order to provide the biospecificity of the [...] Read more.
The detection of CA 125 protein in a solution using a silicon-on-insulator (SOI)-nanowire biosensor with n-type chip has been experimentally demonstrated. The surface of nanowires was modified by covalent immobilization of antibodies against CA 125 in order to provide the biospecificity of the target protein detection. We have demonstrated that the biosensor signal, which results from the biospecific interaction between CA 125 and the covalently immobilized antibodies, increases with the increase in the protein concentration. At that, the minimum concentration, at which the target protein was detectable with the SOI-nanowire biosensor, amounted to 1.5 × 10−16 M. Full article
(This article belongs to the Special Issue Electrical and Electro-Optical Biosensors)
Show Figures

Figure 1

Review

Jump to: Editorial, Research

29 pages, 2609 KiB  
Review
Printed Electrochemical Biosensors: Opportunities and Metrological Challenges
by Emilio Sardini, Mauro Serpelloni and Sarah Tonello
Biosensors 2020, 10(11), 166; https://doi.org/10.3390/bios10110166 - 4 Nov 2020
Cited by 40 | Viewed by 5456
Abstract
Printed electrochemical biosensors have recently gained increasing relevance in fields ranging from basic research to home-based point-of-care. Thus, they represent a unique opportunity to enable low-cost, fast, non-invasive and/or continuous monitoring of cells and biomolecules, exploiting their electrical properties. Printing technologies represent powerful [...] Read more.
Printed electrochemical biosensors have recently gained increasing relevance in fields ranging from basic research to home-based point-of-care. Thus, they represent a unique opportunity to enable low-cost, fast, non-invasive and/or continuous monitoring of cells and biomolecules, exploiting their electrical properties. Printing technologies represent powerful tools to combine simpler and more customizable fabrication of biosensors with high resolution, miniaturization and integration with more complex microfluidic and electronics systems. The metrological aspects of those biosensors, such as sensitivity, repeatability and stability, represent very challenging aspects that are required for the assessment of the sensor itself. This review provides an overview of the opportunities of printed electrochemical biosensors in terms of transducing principles, metrological characteristics and the enlargement of the application field. A critical discussion on metrological challenges is then provided, deepening our understanding of the most promising trends in order to overcome them: printed nanostructures to improve the limit of detection, sensitivity and repeatability; printing strategies to improve organic biosensor integration in biological environments; emerging printing methods for non-conventional substrates; microfluidic dispensing to improve repeatability. Finally, an up-to-date analysis of the most recent examples of printed electrochemical biosensors for the main classes of target analytes (live cells, nucleic acids, proteins, metabolites and electrolytes) is reported. Full article
(This article belongs to the Special Issue Electrical and Electro-Optical Biosensors)
Show Figures

Figure 1

16 pages, 2433 KiB  
Review
Printed Circuit Board (PCB) Technology for Electrochemical Sensors and Sensing Platforms
by Hamed Shamkhalichenar, Collin J. Bueche and Jin-Woo Choi
Biosensors 2020, 10(11), 159; https://doi.org/10.3390/bios10110159 - 30 Oct 2020
Cited by 78 | Viewed by 14041
Abstract
The development of various biosensors has revolutionized the healthcare industry by providing rapid and reliable detection capability. Printed circuit board (PCB) technology has a well-established industry widely available around the world. In addition to electronics, this technology has been utilized to fabricate electrical [...] Read more.
The development of various biosensors has revolutionized the healthcare industry by providing rapid and reliable detection capability. Printed circuit board (PCB) technology has a well-established industry widely available around the world. In addition to electronics, this technology has been utilized to fabricate electrical parts, including electrodes for different biological and chemical sensors. High reproducibility achieved through long-lasting standard processes and low-cost resulting from an abundance of competitive manufacturing services makes this fabrication method a prime candidate for patterning electrodes and electrical parts of biosensors. The adoption of this approach in the fabrication of sensing platforms facilitates the integration of electronics and microfluidics with biosensors. In this review paper, the underlying principles and advances of printed board circuit technology are discussed. In addition, an overview of recent advancements in the development of PCB-based biosensors is provided. Finally, the challenges and outlook of PCB-based sensors are elaborated. Full article
(This article belongs to the Special Issue Electrical and Electro-Optical Biosensors)
Show Figures

Figure 1

Back to TopTop