Skip to Content
You are currently on the new version of our website. Access the old version .
  • Article
  • Open Access

18 November 2025

25 Pages

Design of a High-Speed Pavement Image Acquisition System Based on Binocular Vision

,
,
,
and
1
School of Mechanical and Precision Instrument Engineering, Xi’an University of Technology, Xi’an 710048, China
2
School of Materials Science and Engineering, Xi’an Jiaotong University, Xi’an 710049, China
*
Author to whom correspondence should be addressed.

Abstract

The acquisition of images of road surfaces not only establishes a theoretical foundation for road maintenance by relevant departments but also is instrumental in ensuring the safe operation of highway transportation systems. To address the limitations of traditional road surface image acquisition systems, such as low collection speed, poor image clarity, insufficient information richness, and prohibitive costs, this study has developed a high-speed binocular-vision-based system. Through theoretical analysis, we developed a complete system that integrates hybrid anti-shake technology. Specifically, a hardware device was designed for stable installation at the rear of high-speed vehicles, and a software algorithm was implemented to develop an electronic anti-shake module that compensates for horizontal, vertical, and rotational motion vectors with sub-pixel-level accuracy. Furthermore, a road surface image fusion algorithm that combines the stationary wavelet transform (SWT) and nonsubsampled contourlet transform (NSCT) was proposed to preserve multi-scale edge and textural details by leveraging their complementary multidirectional characteristics. Experimental results demonstrate that the fusion algorithm based on SWT and NSCT outperforms those using either SWT or NSCT alone across quality evaluation metrics such as QAB/F, SF, MI, and RMSE: at 80 km/h, the SF value reaches 4.5, representing an improvement of 0.088 over the SWT algorithm and 4.412 over the NSCT algorithm, indicating that the fused images are clearer. The increases in QAB/F and MI values confirm that the fused road surface images retain rich edge and detailed information, achieving excellent fusion results. Consequently, the system can economically and efficiently capture stable, clear, and information-rich road surface images in real-time under high-speed conditions with low energy consumption and outstanding fidelity.

1. Introduction

Certainly, highways are one of the important infrastructures of national development and are one of the factors important for the development of society. Long-term running of vehicles and the influence of natural causes lead the surface of highways to erode and cause cracks, potholes, craters, bulges, and so on. These defects not only undermine driving safety but also hinder people’s travel. Poor maintenance brings about a high risk of severe accidents and serious economic losses. As a result, regular maintenance is required for keeping the roads sound and safe. Road maintenance calls for scheduled data collection on the surface conditions of the road to detect defects and help enforcement authorities to address them specifically. However, existing popular crowdsourced app-driven data collecting models suffer from deficiencies such as great dependence on network connections, limited geographic coverage, and low user involvement. These limitations lead to the poor quality of the data and affect the emergency management efficiency of the administrative agents. To overcome these challenges, it is essential to deploy intelligent road monitoring systems with high-resolution imaging and powerful real-time analysis tools for highly accurate defect detection. Such systems can dynamically inform maintenance strategies, offering substantial practical value for optimizing road network governance [1].
The advancement of smart transportation systems [2] has emerged as a pivotal benchmark for urban modernization efficiency, safety, and sustainability through technological innovation. Within this framework, autonomous driving technology is emerging as a transformative catalyst for next-generation mobility solutions. Nevertheless, despite its revolutionary potential, this technology confronts critical implementation barriers, including operational reliability concerns in real-world scenarios, particularly in complex environments such as urban thoroughfares, highway networks, and rural roads, where perception and decision-making algorithms demonstrate constrained capabilities. To overcome these technical hurdles, sophisticated road surface image acquisition systems have become indispensable infrastructure components. These systems not only provide cost-effective and high-fidelity data streams for vehicular perception modules but also enable situational awareness through surface condition analytics, thereby comprehensively improving system robustness and safety parameters.
Consequently, the deployment of such acquisition systems holds substantial engineering significance for smart transportation evolution as vital technical enablers for achieving intelligent, efficient, and secure transportation systems. Current road surface inspection systems primarily rely on dedicated vehicles to capture high-quality image data for damage detection. In 2002, the Research Group of Intelligent Inspection Vehicle of Highway at Nanjing University of Science and Technology pioneered China’s first intelligent road inspection vehicle [3]. Equipped with a high-speed digital sensor, it achieved image capture at 70 km/h with a resolution of 1300 × 1030 and 10 fps. However, while effective on smooth roads, the system could not compensate for motion blur caused by vibrations. In 2012, Wuhan Opto Valley Excellence Technology Co., Ltd. (Wuhan, China) introduced the ZOYON-RTM system [4], automating rapid image acquisition during standard driving at speeds of up to 100 km/h. Despite these advances, motion blur remained unresolved. For mountainous terrains, the National Road Maintenance Management Research Center developed the Customer Information Control System (CiCS) road information acquisition system, operating at 30 km/h [5], with specialized stabilization. Yet, its low speed severely limited efficiency.
Technological integration saw progress in 2019 when Tsinghua University researchers Zhou Youjia and Guo Runhua developed a 3D inspection system combining road surface data with environmental mapping via LiDAR and stereo cameras. Recently, unmanned aerial vehicles have appeared as alternatives, with dual optical–electronic stabilizations cancelling the vibration artifacts. However, they are too expensive and massive and have too heavy sensor loads. In summary, there are three aspects of bottlenecks: limit in speed (120 km/h), poor deblurring algorithm, and costly multi-sensor integration. Overcoming these requires breakthroughs in real-time image optimization and adaptive sensor fusion.
The escalating demands of modern infrastructure management—requiring simultaneous achievement of high-throughput operation (>100 km/h), cost-efficiency (<CNY 50,000 per unit), and submillimeter-level precision—have rendered conventional road inspection systems obsolete. This paper presents a binocular vision-based imaging system specifically engineered for high-velocity pavement quality assessment, addressing the critical need for vibration mitigation in mobile sensing platforms. To meet the dual challenge of high-speed operation (>100 km/h) and submillimeter precision in road surface imaging, we developed a bimodal stabilization system integrating passive mechanical dampers with adaptive computational correction. The demands of road maintenance tasks and stringent management requirements dictate that the system operate at speeds exceeding 100 km/h. At such high speeds, slight vehicle vibrations can cause motion blur in the captured road surface images. This blur, whether global or local, leads to a severe loss of detail. To address this issue, a hybrid anti-shake technology combining hardware-based mechanical stabilization and software-based electronic stabilization was proposed. Compared to standalone mechanical or electronic stabilization, the hybrid approach integrates physical compensation with algorithmic processing, enabling it to handle a wider range of vibrations, including high-frequency minor vibrations and low-frequency major vibrations. It performs exceptionally well in complex scenarios (e.g., motion capture, low-light environments). While standalone mechanical stabilization has minimal impact on image quality, it may still have blur under extreme vibrations. In contrast, hybrid anti-shake technology effectively reduces image quality loss by further compensating with electronic stabilization. Additionally, hybrid anti-shake dynamically adjusts stabilization strategies based on the type and intensity of vibrations, providing more flexible and efficient stabilization. Although hybrid anti-shake requires the integration of both mechanical components and algorithmic support, its overall cost may be lower than solutions relying solely on high-performance mechanical stabilization. By comparison, standalone electronic stabilization mainly relies on algorithmic processing, with limited compensation capability for large vibrations, whereas hybrid anti-shake significantly enhances stabilization effectiveness through the physical compensation of mechanical stabilization. Electronic stabilization often requires cropping the frame to compensate for vibrations, resulting in a loss of field of view, whereas hybrid anti-shake reduces the reliance on frame cropping through mechanical stabilization, preserving more field of view. Moreover, hybrid anti-shake reduces blur through mechanical stabilization and further optimizes the image using electronic stabilization, resulting in overall image quality superior to standalone electronic stabilization. Furthermore, electronic stabilization may introduce delays due to algorithmic processing, whereas hybrid anti-shake effectively reduces latency by compensating for vibrations in real time through mechanical stabilization. Overall, hybrid anti-shake technology demonstrates significant advantages in stabilization effectiveness, image quality preservation, and real-time performance, making it an ideal solution for complex scenarios. Given that existing systems rely on single stabilization technologies and struggle to balance cost and performance, this paper proposes hybrid anti-shake as a solution to this contradiction.
This hybrid anti-shake technology simultaneously achieves stabilization during the image acquisition and image processing phases, thereby enhancing the accuracy and reliability of high-speed acquisition while ensuring the longevity and long-term accuracy of the acquisition system. For pavement image information acquisition systems, in addition to employing mechanical fixation devices to stabilize image clarity, traditional approaches for enhancing image quality include image transformation, image enhancement, and image restoration. Youla et al. applied convex set projection theory to image restoration, achieving notable improvements in image clarity [6]. Glasner et al. proposed a single-image super-resolution method that leverages internal image statistics combined with prior knowledge and edge information to enhance image sharpness [7]. Dong et al. introduced a deep learning-based approach for image super-resolution, utilizing a deep convolutional neural network as a mapping model to reconstruct high-resolution images from low-resolution inputs [8]. Zhang et al. developed a deep convolutional neural network-based method for image denoising capable of handling multiple general image denoising tasks [9]. Chen et al. implemented an end-to-end trainable fully convolutional network for low-light image processing, directly processing raw sensor data to replace conventional image processing pipelines and thereby enhance image clarity [10]. Wang Yang et al. presented a fusion method combining generative adversarial networks with multi-scale recursive networks, effectively addressing motion-induced blur and achieving satisfactory image restoration [11].
In summary, while the aforementioned methods can directly improve image clarity, they heavily depend on training datasets and computational time, requiring image processing systems with substantial computational and storage resources. The design and development of pavement image acquisition systems by researchers worldwide predominantly rely on single imaging devices without dedicated modules for stabilizing image clarity. Consequently, these systems cannot eliminate motion blur caused by minor vibrations during high-speed acquisition in real-time, resulting in compromised image quality and information richness. In contrast, image fusion technology can not only average pixel values across multiple images to reduce random noise but also complement information from different images, thereby enhancing both clarity and informational richness.
Currently, most pavement information acquisition systems developed by global research teams utilize single cameras for data collection, producing individual pavement images. Even systems equipped with multiple cameras primarily expand the scope and quantity of image acquisition without improving overall image quality. Such systems no longer meet the requirements of road maintenance management. The coordinated utilization of multi-camera pavement image information to enhance both clarity and detail richness has become a critical challenge. Image fusion technology can address this issue through three hierarchical levels: pixel-level, feature-level, and decision-level fusion [12]. Pixel-level fusion directly combines information from multiple source images, preserving fine details and improving image quality, making it a research focus in recent years. Feature-level fusion involves extracting and comprehensively analyzing image features before integration [13]. Compared to pixel-level fusion, this approach incurs greater information loss. Decision-level fusion primarily employs feature extraction and classification for integration but requires extensive decision systems, resulting in the highest information loss. Based on this comparative analysis, research on image fusion technology for high-speed pavement information acquisition systems will focus on pixel-level fusion to enhance image clarity and information richness.
Subsequently, high-speed acquired road surface images were transmitted in real time to a PC via an HDMI interface for pixel-level image fusion processing. An image fusion algorithm based on a stationary wavelet transform and nonsubsampled contourlet transform was designed to further improve the clarity and information richness of road surface images. Finally, a high-speed road surface acquisition experiment was carried out on an unobstructed road section. By analyzing the clarity S of the acquired images and comparing it with traditional mechanical anti-shake technology, the feasibility and advantages of the hybrid anti-shake technology were demonstrated. Additionally, image fusion tests were performed using the acquired original images, with QAB/F, SF, MI, and RMSE as evaluation metrics. By comparing the results of the image fusion method based on SWT (stationary wavelet transform) and NSCT (nonsubsampled contourlet transform) with those obtained using SWT and NSCT individually, the feasibility of the SWT- and NSCT-based image fusion method was validated.

3. Experimental Evaluation

3.1. Road Surface Image Acquisition Experiment

The experiment was carried out using an image acquisition vehicle equipped with a high-speed road surface image acquisition system on an unobstructed smooth road section. The performance of the system was evaluated by continuously recording acquired road surface images in various speed ranges, followed by an analysis of the results. The aim was to analyze the acquisition results and demonstrate the feasibility of the hybrid anti-shake technology in the stabilization module of the system.
The high-speed acquisition of pavement images was conducted on unobstructed and smooth road segments. Pavement images continuously captured at various speed intervals of the system were recorded, and the results were evaluated and analyzed. In the image acquisition module of the system, the OV2710 binocular image sensors were vertically oriented toward the road surface, with a separation of 1.5 cm between the two sensors and a height of 25 cm above the pavement. The image reception device was placed inside the trunk of the acquisition vehicle to receive real-time high-speed pavement images, and all modules were debugged to ensure normal system operation.
The high-speed acquisition experiment was divided into two phases. In the first phase, continuous pavement images were captured at speeds of 20 km/h, 40 km/h, and 60 km/h, respectively. For each speed interval, images were acquired over a distance of 500 m, with a frame rate of 120 FPS and an exposure time of 7.3 ms. Assuming the field of view width of the acquired images is Wt and the height is H, the formula for calculating the field of view range of the system’s image acquisition is as follows:
A = Wt × H
The field of view height H of the images acquired by the system is calculated as follows:
H = D   ×   t a n a 2
where D denotes the height of the image sensor above the ground, and a represents the vertical field of view angle, calculated as follows:
a = 2 a r c t a n h 2 f
where h is the height of the image sensor, and f is the focal length of the image sensor.
The field of view width Wt of the system’s acquired images is calculated as follows:
Wt = 2W + d
where Wt denotes the total field of view width, and W represents the field of view width of a single sensor.
W = H × P
where P is the aspect ratio of the image sensor, H is the field of view height of the image sensor, and d is the distance between the two sensors.
Based on the aforementioned analysis and calculations, the field of view range for high-speed image acquisition by the system is determined to be 63 cm × 30.75 cm. After confirming the system’s capability to capture clear pavement images at 60 km/h, the image acquisition module was calibrated to ensure operational stability. The system subsequently proceeded to continuously capture high-speed pavement images at 80 km/h, 100 km/h, and 120 km/h, with each speed segment covering a distance of 500 m.
Upon achieving clear image acquisition at 120 km/h, the collection vehicle continued to accelerate in increments of 5 km/h. The captured pavement images were observed, and the motion blur value was calculated for each speed segment. When the motion blur value exceeds 1, it leads to image quality degradation and visible blurring phenomena. Given the collection vehicle’s speed v and the image sensor’s exposure time t, the motion blur value is calculated as follows:
x = vtβ
where β is the image magnification ratio, set to 4.
Table 2 lists the number of road surface images acquired by the system for each speed range.
Table 2. Image acquisition table.
As shown in Figure 9, during the first phase of the acquisition experiment, the system continuously acquired road surface images at speeds of 20, 40, and 60 km/h. It could be observed that the quality of the road surface images acquired at these three speeds was good, with no blur, indicating that both the hardware fixation device and the electronic stabilization system effectively compensated for motion during high-speed acquisition, ensuring system stability. The high-speed acquired road surface images were first cached and processed in the DDR3 SDRAM of the FPGA hardware platform and then transmitted in real time to the PC via HDMI for display. The calculated motion blur values for the road surface images at 20 km/h, 40 km/h, and 60 km/h were 0.1620, 0.3244, and 0.4864, respectively, all of which were less than 1, indicating a good quality of the acquired images with no loss of detailed information.
Figure 9. (a,b) Binocular road surface images acquired by the system at speeds of 20 km/h; (c,d) binocular road surface images acquired by the system at speeds of 40 km/h; (e,f) binocular road surface images acquired by the system at speeds of 60 km/h.
Figure 10 shows the binocular road surface images acquired by the system at high speeds of 80, 100, and 120 km/h. Table 3 presents the clarity of the road surface images acquired by the system at speeds ranging from 20 km/h to 120 km/h.
Figure 10. (a,b) Binocular road surface images acquired by the system at speeds of 80 km/h; (c,d) binocular road surface images acquired by the system at speeds of 100 km/h; (e,f) binocular road surface images acquired by the system at speeds of 120 km/h.
Table 3. Clarity of road surface images acquired by the system at speeds of 20 km/h to 120 km/h.
As shown in Table 3 and Figure 10, the road surface images acquired by the system at 80, 100, and 120 km/h had no blur and demonstrated good clarity, with values close to 1. The calculated motion blur values for these speeds are 0.6488, 0.8108, and 0.9732, respectively, all of which are less than 1. Therefore, the system meets the design requirements for high-speed road surface image acquisition. When the acquisition vehicle reached a speed of 125 km/h, localized blur began to appear in the images with a significant loss of detailed information. The calculated motion blur value was 1.013 and the clarity was 0.3450, which was far from 1. At this speed, the system was unable to acquire clear images. This indicates that the system can acquire clear road surface images with a resolution of 640 × 480 pixels at a speed of 120 km/h.
To compare the image clarity effects of the traditional mechanical stabilization methods and hybrid stabilization technology during high-speed acquisition, high-speed road surface images acquired at 60, 80, 100, and 120 km/h were analyzed. The results of the image clarity enhancement using the two methods are compared in Figure 11.
Figure 11. (a,b) Mechanical stabilization and hybrid stabilization at 60 km/h; (c,d) mechanical stabilization and hybrid stabilization at 80 km/h; (e,f) mechanical stabilization and hybrid stabilization at 100 km/h; (g,h) mechanical stabilization and hybrid stabilization at 120 km/h.
As shown in Figure 11 and Figure 12, the hybrid stabilization technology demonstrated superior performance in enhancing the clarity of high-speed images. The image clarity at speeds ranging from 60 to 120 km/h was consistently higher than that achieved with traditional mechanical stabilization methods, with improvements of 37.2%, 15.2%, 22.3%, and 7.5%, respectively. This technology can process and compensate for image jitter in real time during high-speed acquisition, offering high precision and effective stabilization. Therefore, the adoption of hybrid stabilization technology in the image clarity enhancement module of this system is feasible.
Figure 12. Bar chart comparing image clarity of two stabilization methods.

3.2. Road Surface Image Fusion Results and Analysis

To compare the proposed image fusion method based on SWT and NSCT with the results of using SWT and NSCT individually for road surface image fusion, the fusion algorithm was analyzed. After preprocessing the road surface images through registration, the two images were aligned in the same coordinate system. OV1 and OV2, two sets of road surface images acquired by the binocular acquisition system at speeds of 20, 40, 60, 80, 100, and 120 km/h, were fused using SWT and NSCT, respectively. Table 4 and Table 5 present the quality evaluations of the fused road surface images using the SWT and NSCT at speeds ranging from 20 to 120 km/h, respectively.
Table 4. Quality evaluation of road surface fusion images using SWT.
Table 5. Quality evaluation of road surface fusion images using NSCT.
As shown in Table 4 and Table 5, the evaluation metric QAB/F for the road surface image fusion results using SWT was higher than that of NSCT, whereas the evaluation metric SF for the road surface image fusion results using NSCT was higher than that of SWT.
As shown in Table 6, after the road surface images acquired by the system at high speeds ranging from 20 km/h to 120 km/h were processed using SWT and NSCT fusion, the image clarity was improved compared with using SWT or NSCT individually, demonstrating better fusion results. As illustrated in Figure 13, by comparing the changes in the quality metrics before and after image fusion across different speed ranges, it is evident that the introduced road surface image fusion algorithm based on SWT and NSCT results in an increase in the QAB/F, SF, and MI metrics after fusion. Specifically, at 100 km/h, the SF value increased by 2.821 and the MI value increased by 3.044 after fusion at 120 km/h.
Table 6. Quality evaluation of road surface fusion images based on SWT and NSCT.
Figure 13. Bar chart comparing road surface image fusion results before and after using SWT and NSCT: (a) QAB/F; (b) SF; (c) MI; (d) RMSE.
As shown in Figure 14, to compare the performance of the three image fusion algorithms, road surface images acquired at four speed ranges—60, 80, 100, and 120 km/h—were used as examples to analyze the quality evaluation results after image fusion using the three algorithms. The fusion results of the road surface image fusion algorithm based on SWT and NSCT outperformed the other two algorithms. Specifically, at 80 km/h, the SF value is 4.5, which is higher than that of the SWT and 4.412 higher than that of the NSCT, indicating that the fused images are clearer. The increase in QAB/F and MI values suggests that the fused images retain richer edges and detailed information, making the image content more comprehensive. This method achieved excellent results when fusing road surface images. Therefore, the image fusion method based on stationary wavelet transform and nonsubsampled contourlet transform is suitable for enhancing the clarity of road surface images and capturing detailed edge information.
Figure 14. Quality evaluation results of image fusion using different algorithms: (a) 60 km/h; (b) 80 km/h; (c) 100 km/h; (d) 120 km/h.

4. Conclusions

Based on binocular vision, the high-speed road surface image acquisition system designed in this study features low cost, low power consumption, real-time performance, and high accuracy. It is capable of acquiring stable, clear, and detailed road surface images under high-speed conditions. By employing a hybrid anti-shake technology combining mechanical and electronic stabilization, the system effectively reduces the impact of vibrations on image quality, enhancing the accuracy and reliability of high-speed acquisition. Subsequently, an image fusion algorithm based on stationary wavelet transform and nonsubsampled contourlet transform is applied to enrich the image information and improve clarity. The conclusions are as follows:
(1)
The external mechanical stabilization of the hardware device of the system uses an acrylic plate with a dimension of 114.5 mm × 156.5 mm × 17 mm and a thickness of 2 mm to securely install the system at the rear of the high-speed acquisition vehicle. An electronic stabilization algorithm was designed in the system to compensate for the horizontal, vertical, and rotational motion vectors of the images in real time. The system continuously acquired road surface images at speeds ranging from 20 to 120 km/h, totaling 26,480 images. The field of view for the image acquisition was 63 cm × 30.75 cm. An evaluation method for image clarity and information richness was established to analyze and assess the acquisition results. The results indicate that the system can achieve the continuous acquisition of clear road surface images with a resolution of 640 × 480 at a speed of 120 km/h.
(2)
To address the issues of insufficient clarity and information richness in high-speed acquired images, a road surface image fusion algorithm based on stationary wavelet transform and nonsubsampled contourlet transform was introduced. This algorithm leverages the complementary characteristics of multi-scale and multidirectional analyses to preserve the edge and detail information in the images. The results show that the road surface image fusion algorithm based on the stationary wavelet transform and nonsubsampled contourlet transform outperforms the fusion algorithms using SWT or NSCT individually in terms of quality evaluation metrics such as QAB/F, SF, MI, and RMSE. At 80 km/h, the SF value is 4.5, which is higher than that of the SWT and 4.412 higher than that of the NSCT, indicating that the fused images are clearer. The increase in QAB/F and MI values demonstrates that the fused road surface images retain rich edges and detailed information, achieving excellent results in image fusion.
In summary, for the high-speed road surface image acquisition system designed in this study, a hybrid anti-shake technology that combines mechanical hardware and electronic stabilization is proposed. This approach comprehensively enhances the system stability and image quality during both the image acquisition and processing stages, enabling the acquisition of stable, clear, and detailed road surface images under high-speed conditions. Additionally, this study is the first to apply SWT + NSCT fusion to road surface images, providing new insights into multimodal perception and further demonstrating the feasibility and superiority of the proposed system. This offers a reliable theoretical foundation for road maintenance management departments and provides significant engineering guidance for the effective implementation of maintenance management methods. Future research will focus on AI-driven intelligence to enhance the intelligence, computational efficiency, and adaptability of the system. For instance, by integrating the real-time capabilities of electronic stabilization with the intelligent advantages of AI, more robust anti-shake solutions can be developed. Through the introduction of more advanced AI algorithms, the system can achieve high-precision and high-efficiency road surface image acquisition and processing in more complex traffic environments. Furthermore, by optimizing heterogeneous computing architectures, such as exploring FPGA + GPU heterogeneous computing, we will support higher frame rates for real-time processing, driving the intelligent and efficient development of traffic systems.

Author Contributions

Conceptualization, Z.D. and R.G.; methodology, Z.D.; software, Z.D.; validation, Z.D., Q.J., and Y.M.; formal analysis, Y.W.; investigation, Z.D.; resources, Y.W.; data curation, R.G.; writing—original draft preparation, Z.D. and R.G.; writing—review and editing, Y.W. and R.G.; visualization, Z.D.; supervision, R.G.; project administration, R.G.; funding acquisition, R.G. All authors have read and agreed to the published version of the manuscript.

Funding

This research received no external funding.

Data Availability Statement

The data used to support the findings of this study are included within the article.

Conflicts of Interest

The authors declare no conflicts of interest.

References

  1. Zhang, H.; Dong, Y.; Hou, Y.; Cheng, X.; Xie, P.; Di, K. Research on asphalt pavement surface distress detection technology coupling deep learning and object detection algorithms. Infrastructures 2025, 10, 72. [Google Scholar] [CrossRef] [Scilit]
  2. Chen, H.; Wen, X.; Liu, Y.; Zhang, H. Research on comprehensive vehicle information detection technology based on single-point laser ranging. Sensors 2025, 25, 1303. [Google Scholar] [CrossRef] [Scilit] [PubMed]
  3. Li, Q.; Li, B.; Mao, Q.; Hu, Q.; Geng, X.; Li, J. Research on intelligent pavement inspection vehicle. In Proceedings of the 2005 Annual Meeting of China Highway Society (I), Xinjiang, China, 18 August 2005; pp. 203–209. [Google Scholar]
  4. Zhang, X.H.; Hong, H.Y.; Hou, J.; Jing, G. Research on real-time detection method for pavement distress images. Electron. Des. Eng. 2009, 17, 36–37,40. [Google Scholar]
  5. Liu, J. Research on the application of CiCS road detection vehicle in asphalt pavement detection. China High. New Technol. 2023, 21, 108–110. [Google Scholar] [CrossRef]
  6. Youla, D.C.; Webb, H. Image restoration by the Method of convex projections. IEEE Trans. Med. Imaging 1982, 2, 81–94. [Google Scholar] [CrossRef] [Scilit] [PubMed]
  7. Glasner, D.; Bagon, S.; Irani, M. Super-resolution from a single image. In Proceedings of the IEEE International Conference on Computer Vision, Kyoto, Japan, 29 September–2 October 2009; pp. 349–356. [Google Scholar]
  8. Dong, C.; Loy, C.C.; He, K.; Tang, X. Image super-resolution using deep convolutional networks. IEEE Trans. Pattern Anal. Mach. Intell. 2016, 38, 295–307. [Google Scholar] [CrossRef] [Scilit] [PubMed]
  9. Zhang, K.; Zuo, W.; Chen, Y.; Meng, D.; Zhang, L. Beyond a gaussian denoiser: Residual learning of deep CNN for image denoising. IEEE Trans. Image Process. 2017, 26, 3142–3155. [Google Scholar] [CrossRef] [Scilit] [PubMed]
  10. Chen, C.; Chen, Q.; Xu, J.; Koltun, V. Learning to see in the Dark. In Proceedings of the IEEE/CVF Conference on Computer Vision and Pattern Recognition, Salt Lake City, UT, USA, 18–22 June 2018; pp. 3291–3300. [Google Scholar] [CrossRef] [Scilit]
  11. Wang, Y.; Chen, C.X.; Zhang, Y.G.; Guo, L.; Shen, P. Image clarity enhancement method based on generative adversarial Network. Mod. Comput. 2022, 28, 64–68. [Google Scholar]
  12. Liu, C.; Jing, Z.; Xiao, G.; Yang, B. Feature-based fusion of infrared and visible dynamic images using target detection. Chin. Opt. Lett. 2007, 5, 274–277. [Google Scholar]
  13. Goshtasby, A.A.; Nikolov, S. Image fusion: Advances in the state of the art. Inf. Fusion 2007, 8, 114–118. [Google Scholar] [CrossRef] [Scilit]
  14. Dai, Y.; Bai, Y.; Zhang, W.; Chen, X. Effectiveness evaluation of hardware design based on vivado HLS. Comput. Knowl. Technol. 2021, 17, 1–4. [Google Scholar] [CrossRef]
  15. Zhan, C.; Long, W.; Ding, Y.; Li, F. Design of multi channel data collection and processing system based on FPGA. J. Shenzhen Univ. (Sci. Eng.) 2016, 3, 127–133. [Google Scholar] [CrossRef] [Scilit]
  16. Yu, S.; Zhang, H.; Peng, L.; Luo, Y. Evaluation algorithm of non-reference image quality applying re-fuzzy theory. Transducer Microsyst. Technol. 2021, 40, 140–143. [Google Scholar] [CrossRef]
  17. Nason, G.P.; Silverman, B.W. The stationary wavelet transform and some statistical applications. In Wavelets and Statistics; Antoniadis, A., Oppenheim, G., Eds.; Springer: New York, NY, USA, 1995; pp. 281–299. [Google Scholar] [CrossRef] [Scilit]
  18. Da Cunha, A.L.; Zhou, J.; Do, M.N. The nonsubsampled contourlet transform: Theory, design, and applications. IEEE Trans. Image Process. 2006, 15, 3089–3101. [Google Scholar] [CrossRef] [Scilit] [PubMed]
  19. Khan, N.Y.; McCane, B.; Wyvill, G. SIFT and SURF performance evaluation against various image deformations on benchmark dataset. In Proceedings of the International Conference on Digital Image Computing: Techniques and Applications, Noosa, QLD, Australia, 6–8 December 2011; pp. 501–506. [Google Scholar] [CrossRef] [Scilit]
Disclaimer/Publisher’s Note: The statements, opinions and data contained in all publications are solely those of the individual author(s) and contributor(s) and not of MDPI and/or the editor(s). MDPI and/or the editor(s) disclaim responsibility for any injury to people or property resulting from any ideas, methods, instructions or products referred to in the content.

Article Metrics

Citations

Article Access Statistics

Multiple requests from the same IP address are counted as one view.