Skip to Content
BuildingsBuildings
  • Article
  • Open Access

10 November 2026

18 Pages

Experimental and FEM Analysis of the Thermal Performance of Calcium Silicate Boards at High-Temperature Exposure

,
,
,
and
1
Department of Engineering for Innovation, University of Salento, 73100 Lecce, Italy
2
Tema Sistemi S.p.A., Via della Transumanza, 5/A, 74121 Taranto, Italy
*
Author to whom correspondence should be addressed.

Abstract

Calcium silicate boards are widely used in passive fire protection due to their high-temperature stability and excellent thermal insulation properties. In this study, thermal performance under high-temperature exposure of three commercially available calcium-silicate-based boards with different compositions, densities, thicknesses, and thermal conductivities was experimentally evaluated and complemented by finite element modeling (FEM). The boards were characterized by X-ray fluorescence (XRF), X-ray diffraction (XRD), Fourier-transform infrared spectroscopy (FTIR), thermogravimetric analysis (TGA), and scanning electron microscopy (SEM) to investigate their composition, thermal stability, phase evolution, and microstructure. High-temperature tests were performed under severe thermal exposure, and temperature evolution on the unexposed surface was monitored. A one-dimensional FEM heat-transfer model employing effective thermophysical properties showed reasonable agreement with the experimental temperature profiles. Under equal-thickness conditions, Skamopro-300 exhibited the lowest unexposed-face temperature, mainly due to its substantially lower effective thermal conductivity, while Promatect-T and Naper-S showed comparatively similar thermal responses. The results demonstrate that combining experimental characterization with FEM provides an effective approach for comparing commercial calcium silicate fireboards and predicting their thermal performance under standardized geometrical conditions.

1. Introduction

In recent years, the rapid expansion of urban infrastructure has raised significant safety concern regarding accidental fires that not only damage the structural integrity but also eventually cause them to collapse, triggering a major disaster. Under high temperatures in the fire, the performance of building components will be significantly weakened [1,2,3,4]. Moreover, confined or complex architectural geometries can make fire suppression and evacuation particularly challenging, often resulting in severe casualties during fire incidents. Fire safety is therefore a fundamental requirement for building systems, ensuring safe evacuation routes for occupants and limiting fire propagation within the structure [5,6]. To moderate damage during fire events, the application of fireproofing materials has become a widely adopted and effective solution. Passive fire protection (PFP) is a core strategy in modern fire safety design for buildings and infrastructure, providing thermal insulation and structural protection without active intervention [7,8]. Fireproofing materials represent a well-established approach for PFP of both equipment and load-bearing structures, playing a critical role in maintaining structural stability and integrity under extreme fire exposure [9].
A wide range of commercially available inorganic materials, both synthetic (e.g., mineral wool, cellular glass, foamed glass, calcium silicate foam, ceramic fibers and foams, aerogel, gypsum foam, geopolymers) and natural (e.g., expanded perlite, exfoliated vermiculite, expanded clay, insulating clay bricks) have been used for passive fire protection applications [10,11,12,13]. Among these materials, calcium-silicate-based fire protective boards are considered particularly suitable for fire protection due to their superior thermophysical properties, including low thermal conductivity, excellent thermal shock resistance, high-temperature stability, and durability under harsh environmental conditions [14].
Calcium-silicate-based boards are typically manufactured from a mixture of calcium sources (Ca2+ or Ca(OH)2) and silica, together with mineral fillers and 3–6 wt% cellulose as reinforcing agents and processing aids during manufacturing. The ingredients are mixed with water to form a slurry, in which calcium silicate hydrate (C-S-H, CaH2SiO4) is generated and serves as the primary strength-giving phase. The slurry is then cast into molds and subjected to autoclaving, resulting in a porous, open-cell rigid foam structure. The advantage of C-S-H foam boards as fire protective material includes their asbestos-free composition, non-combustible classification (Class A1, GB8624-2006 [15]), relatively low density and thermal conductivity, environmental friendliness, high mechanical strength, weather resistance, water and moisture resistance, and resistance to biological degradation due to their high alkalinity [16,17]. For materials intended for fire protection applications, their thermal properties at elevated temperatures are particularly important, as changes in thermal conductivity, specific heat capacity, density, and associated heat-transfer mechanisms can strongly influence their insulation performance and the temperature evolution through the protective layer during high-temperature exposure.
Accurate prediction of temperature evolution in thermal protection panels during high-temperature exposure is essential for evaluating their thermal performance and insulation efficiency. Finite element methods (FEMs) provide a powerful tool for predicting temperature profiles under various heating conditions and represent an important approach for understanding heat-transfer mechanisms and the thermal response of materials and structures subjected to elevated temperatures [18].
In the present study, three commercially available calcium-silicate-based fire protection boards with different thicknesses, densities, and thermal conductivities were investigated. Their microstructural, physical, and thermal properties were characterized, and their thermal response under controlled high-temperature exposure was experimentally evaluated. The measured temperature evolution was compared with FEM simulations to assess the thermal insulation performance of the boards and to investigate the influence of material properties and board thickness on heat transfer under elevated-temperature conditions.

2. Materials and Methods

2.1. Materials Selection

After a comprehensive survey of commercially available inorganic fireproof materials, three calcium-silicate-based fireproof boards from independent manufacturers were selected for this study. Among the samples, Skamopro 300 is the lightest (300 kg/m3) followed by Promatect-T (900 kg/m3) and Naper S (1200 kg/m3). The much lower density of the Skamopro 300 sample indicates high porosity, which is reflected in the low thermal conductivity (0.072 W/mK) compared to Promatect-T (0.21 W/mK) and Naper S (0.25 W/mK).
The selected boards, along with their product codes and thermophysical properties as provided in the manufacturers’ technical data sheets, are summarized in Table 1.
Table 1. Physicochemical characteristics of the selected fireboards according to the technical data sheet available from the manufacturers.

2.2. Characterizations

The compositional analysis of the fire protective boards was performed with a Bruker M4 Tornado (Bruker, Karlsruhe, Germany) X-ray Fluorescence spectrophotometer (XRF) operating at 50 KV and 600 μA (30 W). The measurements were performed by scanning in area mode (1 cm2 area) to avoid inhomogeneous distribution of the compounds/elements. The microstructure of the fireproof boards was observed with a field emission scanning electron microscope (FE-SEM Ziess, Oberkochen, Germany). XRD analyses were performed with a Rigaku Ultima X-ray diffractometer (Rigaku Corporation, Tokyo, Japan) operating at 40 kV and 30 mA with a scanning step of 0.02°. Thermogravimetric analysis (TGA) was carried out in air to evaluate the presence of organic content and observe the thermal decomposition behavior of the fireboards. TGA of the as-received fireboards was performed with a Mettler thermoanalyzer (Mettler Toledo, Star system, Greifensee, Switzerland) at a heating rate of 10 °C/min in an air atmosphere from 25° to 1200 °C temperature range.

2.3. High-Temperature Thermal Performance Test

The thermal performance of the selected calcium silicate boards was evaluated under controlled laboratory high-temperature exposure by monitoring the temperature evolution across the specimens. A customized time–temperature heating profile was adopted to provide a severe and reproducible thermal environment and to enable comparison of the thermal insulation behavior of the different boards.
The as-received boards were cut into 28 cm × 28 cm square panels to fit the furnace opening. As illustrated in the experimental setup in Figure 1, four K-type thermocouples (T1–T4) were positioned at different locations on the unexposed surface of the calcium silicate board to monitor temperature evolution and spatial temperature distribution during high-temperature exposure. The reported unexposed-surface temperature was calculated as the mean of these four measurements, while the corresponding standard deviation was used to describe the spatial temperature variation across the tested panel. These measurements represent spatial measurements within a single specimen and should not be interpreted as independent specimen replicates.
Figure 1. Experimental setup for high-temperature thermal performance evaluation of calcium silicate boards, showing thermocouple positioning (T1–T4), the PicoLog TC-08 temperature data logger, and the computerized data acquisition system.
Temperature data were recorded using a PicoLog TC-08 (Pico Technology Limited, Cambridgeshire, United Kingdom) data logger connected to a computer (Figure 1). An additional thermocouple was introduced from the rear side of the furnace and maintained in direct contact with the exposed surface of the board to monitor the temperature applied to the specimen.
The furnace temperature was increased at a nominal heating rate of 8 °C/min up to 1300 °C, followed by an isothermal holding period of 2 h. This heating program was selected to provide controlled and severe high-temperature exposure for assessing the thermal response of the boards. The temperature evolution on both the exposed and unexposed surfaces was continuously monitored to evaluate heat transfer through the specimens.
The purpose of this test was to compare the high-temperature thermal response and insulation performance of the selected boards under identical controlled heating conditions. The measured temperature profiles were subsequently used to evaluate the heat-transfer behavior of the boards and for comparison with the FEM simulations.

3. Results and Discussion

3.1. Physicochemical Characteristics

The compositional analysis of the fire protective boards quantified by XRF spectrometry is summarized in Table 2 and reported as wt% of the corresponding oxides. Naper S and Skamopro 300 show Ca/Si ratio of 0.852 and 1.151, whereas Promatect-T shows a comparatively high Ca/Si ratio of 1.474. It is also interesting to observe the presence of a significant amount of alumina (Al2O3, 30.63 wt%) in Promatect-T sample compared to other calcium silicate boards (Naper S contains 4.39 wt%, Skamopro 300 contains 1.03 wt%). The oxide compositions of the selected fireboards after calcination at 1200 °C for 60 min are also presented in Table 2. The elemental compositions before and after calcination remain largely unchanged, with only minor variations, which may be attributed to sample inhomogeneity or elemental redistribution during thermal treatment.
Table 2. Compositional analyses (wt%) of the as-received and 1200 °C-treated fireboards quantified with XRF spectrometry.
Thermogravimetric analyses (TGA) of the selected fireboards are shown in Figure 2a. All samples exhibit an initial weight loss below 200 °C, corresponding to the evaporation of pore and capillary water and the dehydration of calcium silicate hydrate (C–S–H) phases [22,23]. A second weight-loss step observed in the range of 300–400 °C is attributed to the thermal decomposition of the cellulose binder. Weight loss occurring between 400 and 450 °C can be associated with the dehydration of portlandite [22]. An additional weight-loss region between 500 and 700 °C is attributed to CO2 release from calcium carbonate formed through surface carbonation during thermal exposure. Weight loss above approximately 770 °C is assigned to dehydroxylation, corresponding to the removal of structural OH groups, primarily from silanol (Si–OH) species in the silicate network. The TGA curves indicate that Promatect-T and Naper-S exhibit similar thermal decomposition behavior, whereas Skamopro-300 shows a slightly different trend, likely due to variations in component stoichiometry.
Figure 2. Thermogravimetric analysis (TGA) curves showing the weight loss (%) as a function of temperature up to 1200 °C for three selected fireboards: Promatect-T, Naper-S, and Skamopro-300. The weight loss amount at each stage is indicated in the respective curves.
Figure 3 shows the XRD pattern of the selected fireboards before and after heat treatment at 1200 °C. The as-received samples exhibit different degrees of crystallinity; while Promatect-T shows less crystallinity, Skamopro-300 and Naper-S show relatively higher crystallinity. All the patterns show several diffraction peaks in the 10–60° 2θ region. In the case of Promatect-T, there is a notable difference in the appearance of a sharp peak around 18° (2θ) for the as-received sample, which corresponds to the portlandite (Ca(OH)2) that disappeared after calcination at 1200 °C, indicating its decomposition [24,25]. This feature is not observed for Naper-S and Skamopro-300 boards. The peaks at 11.7°, 23.58°, 29.65°, and 32.7° of 2θ could be assigned to the presence of hydrated calcium silicate phases (C-S-H), which is common in fire-resistant calcium silicate boards [22,26,27,28]. After calcination at 1200 °C, all these phases disappear and transform into the more thermally stable Wollastonite (CaSiO3) crystalline phase [25]. Some additional peaks are also visible that can be assigned to the formation of calcium silicate polymorphs, such as dicalcium silicate (Ca2SiO4) and calcium aluminate (CaAl2O4). These transformations are associated with solid-state reactions between CaO and SiO2 during the sintering process. Similar crystalline transformation was also observed for Skamopro-300 and Naper-s, with the appearance of a stronger SiO2 peak due to the presence of quartz. The appearance of relatively stronger quartz peaks in Skamopro-300 and Naper-S suggests either incomplete reaction during heat treatment or the presence of excess silica-containing filler, which is supported by the XRF compositional analyses (Table 2). It is also worth mentioning that the presence of Al2O3 can be identified in Promatect-T due to the appearance of corundum diffraction peaks at 2θ of 25.6° and 35.14°. This is consistent with the compositional analysis of XRF, where a higher amount of Al2O3 is observed for the Promatect-T sample. This higher amount of Al2O3 presence in the Promatect-T board enhances its structural integrity during high-temperature operation, which could make it superior to the other fireboards.
Figure 3. XRD pattern of the as-received samples and after heat treatment at 1200 °C for 60 min.
FT-IR spectra of the as-received and 1200 °C calcined fireboards are shown in Figure 4a–f, where several structural and compositional changes related to dehydration, decarbonation, and silicate-phase transformation are observed. Distinct vibrational peaks of the respective samples, before and after heat treatment, are marked in the figure. The appearance of a broad vibration band at the higher wavenumber centered at 3645 cm−1 can be assigned to the O-H stretching vibration of Ca(OH)2 [22], and a broad peak centered around 3400 cm−1 is due to O-H stretching vibrations of surface hydroxyl groups in the C-S-H structure. Another weak absorption at 1645 cm−1 could be attributed to adsorbed water molecules. The broad and relatively strong band in the range of 1400–1500 cm−1 is caused by CO2, which may arise from either adsorbed CO2 or the presence of amorphous carbonates [24,25]. A group of intense bands between 900 and 1200 cm−1 originates from the asymmetric and symmetric stretching vibrations of Si-O-Si bonds, confirming silica presence in all fireboards. The relatively strong and sharp Si-O-Si bonds in Naper-S and Skamopro-300 boards, compared to Promatect-T, indicate a higher amount of silica, as observed in XRF analyses (Table 2) and XRD diffractogram. Notably, for the as-received Naper-S and Promatect-T, a strong peak around 964 cm−1 and a weaker band at 873 cm−1 are observed, which disappear after calcination at 1200 °C; these can be attributed to cellulose binder (C-O and C-C stretching vibrations). This feature is less prominent in Promatect-T, possibly due to a lower cellulose content or masking by Si-O-Si bands. Additionally, peaks between 900 and 950 cm−1 emerge after calcination, likely due to the formation of α-Wollastonite, as indicated by the XRD spectrum [26].
Figure 4. FTIR spectra of the as-received and heat-treated samples at 1200 °C for 60 min. (a,b) Promatect–T, (c,d) Skamopro–300, and (e,f) Naper–S. “1200” indicates heat treatment at 1200 °C.
The microstructures of as-received and heat-treated at 1200 °C fireproof boards are shown in Figure 5. Low-magnification images clearly reveal fibers embedded within a porous calcium silicate matrix (Figure 5a–c). Significant open porosity and inter-fiber voids are visible, contributing to the low bulk density and thermal insulation properties. At higher magnification (Figure 5d–f), the matrix pf Promatect shows poorly crystallized calcium silicate hydrates with irregular morphology. Needle-like and flaky structures are observed, indicating the presence of hydrated phases in Naper-S and Skamopro-300. The presence of elongated reinforcing fibers and plate-like phases suggests a typical autoclaved calcium silicate hydrate structure. The microstructure appears loosely packed, with limited interparticle bonding. After exposure to 1200 °C (Figure 5g–i), the microstructure becomes more homogeneous and compact indicating significant microstructural densification due to thermal exposure. High-magnification images (Figure 5j–l) show a clear transformation toward a denser and more cohesive microstructure. The needle-like hydrates appear coarsened and grain-like agglomerates are formed. This suggests dehydration-induced densification and partial-phase transformation (discussed in XRD). The reduction in visible microporosity indicates shrinkage and microstructural consolidation. Among the samples, differences in fiber distribution and matrix compactness suggest that boards with a more uniform fiber dispersion and controlled porosity exhibit improved thermal stability and reduced cracking after heating.
Figure 5. FE-SEM micrographs of Promatect-T (a,d,g,j), Naper-S (b,e,h,k), and Skamopro-300 (c,f,i,l) in the as-received condition (a–f) and after thermal exposure at 1200 °C (g–l). Images (a–c,g–i) were acquired at 200× magnification (scale bar: 200 µm), while images (d–f,j–l) were acquired at 20,000× magnification (scale bar: 2 µm).

3.2. High-Temperature Thermal Performance

Figure 6 presents the time–temperature profiles recorded on the unexposed surfaces of the three calcium silicate boards during high-temperature thermal exposure, together with the applied furnace temperature. The furnace temperature increased at a nominal rate of 8 °C/min to approximately 1300 °C, followed by an isothermal holding period. Under these severe thermal conditions, all three boards substantially delayed heat transmission from the exposed to the unexposed surface, confirming their ability to provide thermal insulation at elevated temperatures.
Figure 6. Plot of the time–temperature curve of all three samples.
Clear differences in temperature evolution were observed among the three boards. Skamopro-300 exhibited the lowest unexposed-surface temperature throughout the exposure period, remaining below approximately 180 °C after 5 h. Promatect-T showed an intermediate thermal response, with the unexposed-surface temperature reaching approximately 260 °C. In comparison, Naper-S exhibited a more pronounced temperature increase, reaching approximately 420 °C, indicating greater heat transmission through the board under the applied experimental conditions.
The observed differences in thermal response are associated with the combined effects of board thickness and thermophysical and microstructural characteristics, including density, thermal conductivity, porosity, and pore structure. These parameters collectively govern heat transfer through porous calcium silicate materials. In particular, low thermal conductivity and a highly porous microstructure can reduce heat transfer and delay the temperature increase at the unexposed surface. However, because the investigated commercial boards differ simultaneously in thickness, density, composition, and thermal properties, the individual contribution of each parameter cannot be isolated from the present experimental results.
Overall, the results demonstrate substantial differences in the high-temperature thermal insulation behavior of the three commercial boards and highlight the importance of considering both material properties and board geometry when selecting calcium silicate materials for thermal protection applications.
Photos of surfaces exposed to fire test for all samples are shown in Figure 7. In the case of Naper-S and Skampro-300, many cracks appear compared to Promatect-T. This shows the reliability of the Promatect-T board during fire over other fireboards.
Figure 7. Photographs of the exposed surface of the fireproof board before and after the fire test.

3.3. Finite Element Modeling (FEM) for Simulating Heat Exchange During Fire

The temperature/time test was analyzed by means of finite element methods (FEMs) using the FlexPDE software version 5. A 1-D heat-exchange model was implemented into the software, which allowed for the solution of the classical II Fourier law:
ρ c p d T d t = ∂ ∂ x k e f f ∂ T ∂ x
where ρ ,   c p and k e f f are the material density, specific heat and thermal conductivity, T is the temperature, t is time, and x the direction of heat transfer. The heat-transfer equation was coupled with proper boundary conditions (BC). Referring to the scheme of Figure 8 the material thermal properties used in the heat-transfer problem are reported in Table 3 and were taken from the material technical data sheet. The only unknown thermal property, specific heat, which was not reported on the TDS, was used as a fitting parameter.
Figure 8. Scheme for the heat-exchange model calculation.
Table 3. Thermophysical properties of the selected fireboards.
The boundary conditions used on the internal oven surface (B1) is
− k e f f ∂ T ∂ x = h c o n v 1 T o v e n − T + h r a d T o v e n − T 4
whereas for the outer surface of the board, in contact with the air at room temperature
− k e f f ∂ T ∂ x = h c o n v 2 T r o o m − T + h r a d T r o o m − T 4
In both Equations (2) and (3), the thermal flux at the interface is made of two different contributions, the first one due to convection, and the second one to radiation; in both equations, hconv represent the convective heat-transfer coefficients, whereas the radiative heat-transfer coefficient, h r a d , was calculated as
h r a d = σ ε f ε s ε f + ε s − ε f ε s
In which εf ed εs are the emissivity of the oven chamber and the exposed surface respectively, and σ = 5.67 × 10−8 W/(m2K4) is the Stefan–Boltzman constant. In the simulations, εf = 1 and, εs = 0.8 were taken [29].
The convective coefficient of Equations (2) and (3) were calculated according to the definition of the Nusselt number:
h c o n v = N u k f l u i d L
in which k f l u i d is the air thermal conductivity and L is the characteristic length of convection, which, for vertical plates, is the wall length.
The Nusselt number for a free convection on a vertical plate was obtained by the Churchill and Chu correlation [30].
N u = 0.825 + 0.387 G r P r 1 / 6 1 + 0.492 P r 9 / 16 8 / 27 2
where Gr is the Grashof number
G r = L 3 ρ 2 g β T − T f l u i d μ 2
and Pr is the Prandtl number
P r = c p μ k
in which β is the thermal expansion coefficient, μ viscosity, T the interface temperature, Tfluid the fluid temperature and Cp is the specific heat. For air, β = 3.7 × 10−3 K−1, μ = 1.7 × 10−5 Pa∙s ρ = 1.2 kg/m3 and k = 0.024 W/mK were taken.
The typical evolution of the convective coefficients on both sides of the Skampopro fireproof panel is reported in Figure 9.
Figure 9. Evolution of convective heat-transfer coefficients as a function of temperature.
The convective and radiative heat fluxes at the two boundaries of the domain are reported in Figure 10. On the oven side, initially, convective and radiative terms are comparable in magnitude. However, as the temperature of the panel on the oven side increases, the radiative term increases; the decrease in the temperature difference T o v e n − T causes a decrease in the convective term. On the other hand, on the room side, the two heat fluxes are comparable in magnitude over the whole-time interval. In fact, in this case the term T r o o m − T continuously increases, which causes the convective term to be significant over the whole-time range of the simulation. However, all the heat flux terms reach an asymptotic value after a reasonable time interval (about 10,000 s in Figure 11), which roughly coincides with the time necessary for the oven to attain the isothermal step. After this transient, the heat-transfer problem becomes substantially stationary. The total positive heat flux (heating from the oven to the panel) becomes equivalent to the total negative heat flux (cooling from the panel to the external air).
Figure 10. Evolution of convective and radiative heat flux as a function of time.
Figure 11. Comparison between experimental and FEM simulation.
A comparison between experimental and simulation data, reported in Figure 11, shows a reasonably good agreement, as highlighted by the results reported in Table 4, which highlight the more relevant results of experimental data and simulation, in terms of heating rate (calculated in the 3000–6000 s range) and maximum temperature. In the simulations, the best fitting of experimental data was found with cp = 840 J/kgK, 2500 J/KgK and 2400 J/KgK for Skamapro 300, Promatect T and Naper S, respectively.
Table 4. Deviations in heating rate and maximum temperature from FEM.
The FEM predictions match the experimentally measured temperature trends for all samples, demonstrating the reliability of the numerical model in capturing the heat-transfer mechanisms during temperature exposure. Deviations between experimental and simulated data can be attributed to simplifications in the model, such as the assumption of temperature-independent thermophysical properties and idealized boundary conditions. Among the tested boards, Skamopro-300 exhibits the lowest unexposed-face temperature both experimentally and numerically, remaining below ~180 °C after 5 h, indicating superior insulation performance. Promatect-T shows intermediate behavior with a stabilized backside temperature of ~260 °C, while Naper-S reaches the highest temperature (~420 °C), reflecting comparatively higher thermal conductivity and/or lower effective insulation thickness. Overall, the good agreement between experimental thermal tests and FEM simulations validates the predictive capability of the numerical approach and demonstrates its usefulness for optimizing fireboard design and predicting thermal performance under different high-temperature exposure conditions without extensive experimental trials.
The superior insulation performance of Skamapro-300 arises from the different thermal properties of the material; however, the thickness also has a significant influence on the heat-transfer phenomena. Therefore, simulations were also run for the three panels at the same thickness, i.e., 25 and 50 mm. The results reported in Figure 12a,b clearly show the same qualitative behavior even when considering the same thickness for the three panels; Skamapro 300 shows the best insulating properties, as evidenced by the lowest unexposed-face temperature compared to the other two panels. In addition, Promatect T and Naper S show very similar temperature evolution, which is in agreement with their very similar thermal properties, as highlighted in Table 2.
Figure 12. FEM simulation results at constant panel thickness. (a) Simulations for a panel thickness of 25 mm and (b) simulations for a panel thickness of 50 mm.
Another relevant result is the substantial difference in temperature evolution when comparing Skamapro 300 with the other two panels: in fact, the former shows a much faster initial temperature increase; according to the thermal properties of Table 2 this is due to the lower values of density and specific heat. Referring to the Fourier number, defined as
F o = k ρ c p L 2 t
It is possible to define the characteristic time for conductive heat transfer as
t C H T = ρ c p L 2 k
For Skamapro, lower density and specific heat involve very low values of tCHT, which in turn involve faster heating and lower time to approach steady state conditions.
However, when steady state is reached, the temperature difference between the exposed and unexposed surface is mainly governed by the thermal conductivity of the panel: the lower conductivity of Skamapro therefore allows us to significantly reduce the maximum temperature attained at the unexposed surface.

4. Conclusions

In this study, three commercially available calcium-silicate-based fire protection boards were characterized to investigate their physicochemical, microstructural, and high-temperature thermal performance. Promatect-T exhibited a higher Ca/Si ratio (1.474) than Naper-S and Skamopro-300 (<1.2), together with a considerably higher Al2O3 content (~30 wt%, compared with 4.4 wt% for Naper-S and ~1 wt% for Skamopro-300), indicating substantial compositional differences among the investigated boards. Thermogravimetric analysis revealed different mass-loss behavior for the three materials, reflecting differences in their composition and thermally induced transformations. XRD analysis identified portlandite (Ca(OH)2) in Promatect-T, indicating the presence of residual calcium hydroxide. In addition, the stronger Si–O–Si vibrational bands observed for Naper-S and Skamopro-300 were consistent with their higher silica content.
Microstructural observations revealed differences in fiber distribution and pore architecture among the boards, which, together with their composition and thermophysical properties, influence their response to high-temperature exposure. During controlled thermal testing up to 1300 °C, all three boards delayed heat transmission to the unexposed surface, although substantial differences in temperature evolution were observed. Skamopro-300 exhibited the lowest unexposed-surface temperature, followed by Promatect-T and Naper-S under the investigated conditions.
The experimentally measured temperature evolution was compared with the FEM predictions, and the numerical model reproduced the overall thermal response of the boards with reasonable agreement. The results demonstrate the applicability of FEM for evaluating heat transfer through calcium silicate boards and for comparing their thermal behavior under controlled high-temperature exposure.
The observed differences in thermal performance arise from the combined influence of board thickness, density, thermal conductivity, composition, and microstructural characteristics. Since these parameters vary simultaneously among the investigated commercial boards, their individual contributions cannot be isolated from the present experimental comparison. Nevertheless, the results highlight the importance of considering both material properties and board geometry when evaluating and designing calcium-silicate-based materials for high-temperature thermal protection applications.

Author Contributions

Conceptualization, S.K.P., S.P., A.G. and A.L.; Methodology, S.K.P., S.P., A.G. and A.L.; Software, S.K.P., S.P. and A.G.; Validation, S.K.P., A.G. and A.L.; Formal analysis, S.K.P., S.P. and A.G.; Investigation, S.K.P., S.P. and A.G.; Data curation, S.K.P., S.P. and A.G.; Writing—original draft, S.K.P., S.P., A.G. and A.L.; Writing—review and editing, S.K.P., S.P., A.G., R.B. and A.L.; Visualization, S.P.; Supervision, S.K.P., S.P., A.G., R.B. and A.L.; Project administration, R.B. and A.L.; Funding acquisition, R.B. and A.L. All authors have read and agreed to the published version of the manuscript.

Funding

This research was supported by the Puglia FESR 2014–2020 Programme (European Regional Development Fund) through the industrial research and experimental development project entitled “Barriere antincendio semipassive, intelligenti ed autoconfiguranti” in collaboration with Tema Sistemi S.p.A., Taranto, Italy.

Data Availability Statement

The original contributions presented in this study are included in the article. Further inquiries can be directed to the corresponding author.

Conflicts of Interest

Author Roberto Borraccino is employed by the company TEMA Sistemi S.p.A. as director and CEO. The authors declare that this study received funding from TEMA Sistemi S.p.A. The author had the following involvement with the study: provided scientific contribution, provided the technological background that guided the selection of the experimental procedure, identified application areas, and evaluated the experimental results. The authors declare that the research has no correlation with the company’s industrial products and that the research was conducted in the absence of any commercial or financial relationships that could be construed as a potential conflict of interest.

References

  1. Kodur, V. Properties of Concrete at Elevated Temperatures. ISRN Civ. Eng. 2014, 2014, e468510. [Google Scholar] [CrossRef] [Scilit]
  2. Kürüm Varolgüneş, F. Typology-Specific Gaps in Building Fire Safety: A Scientometric Review of Technologies, Functions, and Research Trends. Fire 2025, 8, 423. [Google Scholar] [CrossRef] [Scilit]
  3. Bhadauria, P.K.S.; Ranit, A.B.; Chaudhary, P.S.; Dongre, K.A.; Harle, S.M.; Bhagat, A.P. Innovative Approaches to Fire-Resistant Building Materials: A Review. Life Cycle Reliab. Saf. Eng. 2025, 15, 353–366. [Google Scholar] [CrossRef] [Scilit]
  4. Ji, J.; Hamins, A.; Hostikka, S.; Jangi, M.; Tanaka, F.; Ding, L. Fire Safety of Complex Buildings (Tall Buildings, Tunnels, Subways, Etc.). Build. Simul. 2022, 15, 493–494. [Google Scholar] [CrossRef] [Scilit]
  5. Yew, M.C.; Yew, M.K.; Yuen, R.K.K. Experimental Analysis of Lightweight Fire-Rated Board on Fire Resistance, Mechanical, and Acoustic Properties. Fire 2023, 6, 221. [Google Scholar] [CrossRef] [Scilit]
  6. Yang, Y.; Sun, Y.; Chen, M.; Zhou, Y.; Wang, R.; Liu, Z. Platform Development of BIM-Based Fire Safety Management System Considering the Construction Site. Buildings 2022, 12, 1268. [Google Scholar] [CrossRef] [Scilit]
  7. Caetano, H.; Vilhena, L.; Ramalho, A.; Santiago, A.; Laím, L.; Monteiro, E. Mechanical Characterisation of Gypsum-Based Passive Fire Protection Mortars with Micro and Nano Silica Particles. Appl. Sci. 2024, 14, 8612. [Google Scholar] [CrossRef] [Scilit]
  8. Hsiao, C.-J.; Hsieh, S.-H. Real-Time Fire Protection System Architecture for Building Safety. J. Build. Eng. 2023, 67, 105913. [Google Scholar] [CrossRef] [Scilit]
  9. Di Padova, A.; Tugnoli, A.; Cozzani, V.; Barbaresi, T.; Tallone, F. Identification of Fireproofing Zones in Oil&Gas Facilities by a Risk-Based Procedure. J. Hazard. Mater. 2011, 191, 83–93. [Google Scholar] [CrossRef] [Scilit] [PubMed]
  10. Gellert, R. 8—Inorganic Mineral Materials for Insulation in Buildings. In Materials for Energy Efficiency and Thermal Comfort in Buildings; Hall, M.R., Ed.; Woodhead Publishing Series in Energy; Woodhead Publishing: Cambridge, UK, 2010; pp. 193–228. ISBN 978-1-84569-526-2. [Google Scholar]
  11. Aziz, I.H.; Al Bakri Abdullah, M.M.; Yong, H.C.; Ming, L.Y.; Hussin, K.; Surleva, A.; Azimi, E.A. Manufacturing Parameters Influencing Fire Resistance of Geopolymers: A Review. Proc. Inst. Mech. Eng. Part L J. Mater. Des. Appl. 2019, 233, 721–733. [Google Scholar] [CrossRef] [Scilit]
  12. Kolaitis, D.I.; Asimakopoulou, E.K.; Founti, M.A. Fire Behaviour of Gypsum Plasterboard Wall Assemblies: CFD Simulation of a Full-Scale Residential Building. Case Stud. Fire Saf. 2017, 7, 23–35. [Google Scholar] [CrossRef] [Scilit]
  13. Wang, Y.; Chuang, Y.-J.; Lin, C.-Y. The Performance of Calcium Silicate Board Partition Fireproof Drywall Assembly with Junction Box under Fire. Adv. Mater. Sci. Eng. 2015, 2015, 642061. [Google Scholar] [CrossRef] [Scilit]
  14. Kristanto, L.; Sugiharto, H.; Agus, S.W.D.; Pratama, S.A. Calcium Silicate Board as Wall-Facade. Procedia Eng. 2017, 171, 679–688. [Google Scholar] [CrossRef] [Scilit]
  15. GB 8624-2006; Classification for Burning Behavior of Building Materials and Products. Standards Press of China: Beijing, China, 2006.
  16. Gravit, M.; Golub, E. The Fire Resistant Ceiling Construction in a Hydrocarbon Fire. MATEC Web Conf. 2018, 245, 03004. [Google Scholar] [CrossRef] [Scilit]
  17. Lin, L.; Wu, B. Chloride Diffusion Behavior of Recycled Lump-Aggregate Concrete: Experiment and Numerical Simulation. Constr. Build. Mater. 2025, 501, 144286. [Google Scholar] [CrossRef] [Scilit]
  18. Prieler, R.; Gerhardter, H.; Landfahrer, M.; Gaber, C.; Schluckner, C.; Eichhorn-Gruber, M.; Schwabegger, G.; Hochenauer, C. Development of a Numerically Efficient Approach Based on Coupled CFD/FEM Analysis for Virtual Fire Resistance Tests—Part B: Deformation Process of a Steel Structure. Fire Mater. 2020, 44, 704–723. [Google Scholar] [CrossRef] [Scilit]
  19. BS 476-7:1997; Fire Tests on Building Materials and Structures – Method of Test To Determine the Classification of the Surface Spread of Flame of Products. British Standards Institution: Loughborough, UK, 1997.
  20. EN 13501-1:2007 + A1:2009; Fire Classification of Construction Products and Building Elements—Part 1: Classification Using Data From Reaction to Fire Tests. European Committee for Standardization: Brussels, Belgium, 2009.
  21. EN 12467; Fibre Cement Flat Sheets—Product Specification and Test Methods. European Committee for Standardization: Brussels, Belgium, 2018.
  22. Garbev, K.; Bornefeld, M.; Beuchle, G.; Stemmermann, P. Cell Dimensions and Composition of Nanocrystalline Calcium Silicate Hydrate Solid Solutions. Part 2: X-Ray and Thermogravimetry Study. J. Am. Ceram. Soc. 2008, 91, 3015–3023. [Google Scholar] [CrossRef] [Scilit]
  23. Maddalena, R.; Hall, C.; Hamilton, A. Effect of Silica Particle Size on the Formation of Calcium Silicate Hydrate Using Thermal Analysis. Thermochim. Acta 2018, 672, 142–149. [Google Scholar] [CrossRef] [Scilit]
  24. Taglieri, G.; Mondelli, C.; Daniele, V.; Pusceddu, E.; Trapananti, A. Synthesis and X-Ray Diffraction Analyses of Calcium Hydroxide Nanoparticles in Aqueous Suspension. Adv. Mater. Phys. Chem. 2013, 3, 108. [Google Scholar] [CrossRef]
  25. Tajuelo Rodriguez, E.; Garbev, K.; Merz, D.; Black, L.; Richardson, I.G. Thermal Stability of C-S-H Phases and Applicability of Richardson and Groves’ and Richardson C-(A)-S-H(I) Models to Synthetic C-S-H. Cem. Concr. Res. 2017, 93, 45–56. [Google Scholar] [CrossRef] [Scilit]
  26. Grangeon, S.; Claret, F.; Lerouge, C.; Warmont, F.; Sato, T.; Anraku, S.; Numako, C.; Linard, Y.; Lanson, B. On the Nature of Structural Disorder in Calcium Silicate Hydrates with a Calcium/Silicon Ratio Similar to Tobermorite. Cem. Concr. Res. 2013, 52, 31–37. [Google Scholar] [CrossRef] [Scilit]
  27. Trezza, M.A. Hydration Study of Ordinary Portland Cement in the Presence of Zinc Ions. Mater. Res. 2007, 10, 331–334. [Google Scholar] [CrossRef] [Scilit]
  28. Jokanović, V.; Čolović, B.; Mitrić, M.; Marković, D.; Ćetenović, B. Synthesis and Properties of a New Dental Material Based on Nano-Structured Highly Active Calcium Silicates and Calcium Carbonates. Int. J. Appl. Ceram. Technol. 2014, 11, 57–64. [Google Scholar] [CrossRef] [Scilit]
  29. Zhang, C.; Usmani, A. Heat Transfer Principles in Thermal Calculation of Structures in Fire. Fire Saf. J. 2015, 78, 85–95. [Google Scholar] [CrossRef] [Scilit] [PubMed]
  30. Churchill, S.W.; Churchill, R.U. A Comprehensive Correlating Equation for Heat and Component Transfer by Free Convection. AIChE J. 1975, 21, 604–606. [Google Scholar] [CrossRef] [Scilit]
Disclaimer/Publisher’s Note: The statements, opinions and data contained in all publications are solely those of the individual author(s) and contributor(s) and not of MDPI and/or the editor(s). MDPI and/or the editor(s) disclaim responsibility for any injury to people or property resulting from any ideas, methods, instructions or products referred to in the content.

Article Metrics

Citations

Article Access Statistics

Multiple requests from the same IP address are counted as one view.