Next Article in Journal
Analysis Method for Post-Impact Damage Development in Carbon Fiber Reinforced Laminate under Repeated Loading
Next Article in Special Issue
The Possibilities of Using Poly(3-hydroxybutyrate-co-3-hydroxyvalerate) PHBV in the Production of Wood–Polymer Composites
Previous Article in Journal
An Overview of Enhancing the Performance of Medical Implants with Nanocomposites
 
 
Font Type:
Arial Georgia Verdana
Font Size:
Aa Aa Aa
Line Spacing:
Column Width:
Background:
Article

Fabrication and Characterization of Piezoelectric PEO/SF/BaTiO3 Scaffolds for Cardiac Tissue Engineering

by
Abdelrahman K. A. Khalil
1,
Hassan Fouad
2,*,
Abdalla Abdal-hay
3,4,
Nasser M. Abd El-salam
2 and
Khalil Abdelrazek Khalil
5,*
1
Graduated from the Mechanical Engineering Department, College of Engineering, King Saud University, Riyadh 12372, Saudi Arabia
2
Applied Medical Science Department, Community College, King Saud University, Riyadh 12642, Saudi Arabia
3
School of Dentistry, University of Queensland, Herston Campus, St. Lucia, QLD 4072, Australia
4
Department of Mechanical Engineering, Faculty of Engineering, South Valley University, Qena 83523, Egypt
5
Department of Mechanical and Nuclear Engineering, College of Engineering, University of Sharjah, Sharjah P.O. Box 27272, United Arab Emirates
*
Authors to whom correspondence should be addressed.
J. Compos. Sci. 2023, 7(5), 200; https://doi.org/10.3390/jcs7050200
Submission received: 20 March 2023 / Revised: 7 May 2023 / Accepted: 12 May 2023 / Published: 16 May 2023
(This article belongs to the Special Issue Functional Additives for Bio-Based Advanced Composites)

Abstract

The existence of an intrinsic electrical platform responsible for the formation and transmission of impulses is essential, especially in cardiac tissue. However, most cardiac tissue made from biodegradable polymeric materials lacks conductive characteristics; this delays regional conduction, potentially causing arrhythmias. This study proposes a conductive polyethylene oxide (PEO)/silk fibroin (SF)-based material conjugated with conductive nanoparticles as a cardiac patch to fix any infarcted heart part. A new composite of PEO/15 wt%SF/0.2 wt%BaTiO3 was prepared and characterized in vitro. The obtained patches were characterized by conventional Bragg-platinum-conductive action (XRD), FTIR spectroscopy, Raman spectra, and thermogravimetric analysis. A PiezoTester device was used to evaluate the piezoelectric properties. The produced samples of 500 μm thickness were assessed in tapping mode. The applied load was selected to be as low as possible, and the frequencies were adjusted to simulate the heartbeats, ranging from 10 to 100 Hz. The results showed that a maximum of around 1100 mV was obtained at a load of 20 N. A maximum of about 80 mV was received at an applied force of 1 N and a frequency of 100 Hz, which matches the electricity generated by the human heart. The cytotoxicity effect of prepared films was tested against AC16 cells using microculture tetrazolium assay (MTT). The pristine PEO cell viability either was not affected by adding SF or slightly decreased. However, the cell viability dramatically increased by adding BaTiO3 to the PEO/SF composites. The confocal microscope images proved that the cells showed a spread morphology. The cells adhered to the PEO membranes and demonstrated a well-spread morphology. Overall, our study suggests that the PEO/SF/BaTiO3 composite can be a promising cardiac patch material for repairing infarcted heart tissue, as it is conductive, has good mechanical properties, and is biocompatible.
Keywords: cardiac tissue engineering; PEO; piezoelectric properties; barium titanate cardiac tissue engineering; PEO; piezoelectric properties; barium titanate

Share and Cite

MDPI and ACS Style

Khalil, A.K.A.; Fouad, H.; Abdal-hay, A.; Abd El-salam, N.M.; Abdelrazek Khalil, K. Fabrication and Characterization of Piezoelectric PEO/SF/BaTiO3 Scaffolds for Cardiac Tissue Engineering. J. Compos. Sci. 2023, 7, 200. https://doi.org/10.3390/jcs7050200

AMA Style

Khalil AKA, Fouad H, Abdal-hay A, Abd El-salam NM, Abdelrazek Khalil K. Fabrication and Characterization of Piezoelectric PEO/SF/BaTiO3 Scaffolds for Cardiac Tissue Engineering. Journal of Composites Science. 2023; 7(5):200. https://doi.org/10.3390/jcs7050200

Chicago/Turabian Style

Khalil, Abdelrahman K. A., Hassan Fouad, Abdalla Abdal-hay, Nasser M. Abd El-salam, and Khalil Abdelrazek Khalil. 2023. "Fabrication and Characterization of Piezoelectric PEO/SF/BaTiO3 Scaffolds for Cardiac Tissue Engineering" Journal of Composites Science 7, no. 5: 200. https://doi.org/10.3390/jcs7050200

APA Style

Khalil, A. K. A., Fouad, H., Abdal-hay, A., Abd El-salam, N. M., & Abdelrazek Khalil, K. (2023). Fabrication and Characterization of Piezoelectric PEO/SF/BaTiO3 Scaffolds for Cardiac Tissue Engineering. Journal of Composites Science, 7(5), 200. https://doi.org/10.3390/jcs7050200

Article Metrics

Back to TopTop